Utilization of by-products derived from bioethanol production process for cost-effective production of lactic acid

The by-products of bioethanol production such as thin stillage (TS) and condensed distillers solubles (CDS) were used as a potential nitrogen source for economical production of lactic acid. The effect of those by-products and their concentrations on lactic acid fermentation were investigated using Lactobacillus paracasei CHB2121. Approximately, 6.7 g/L of yeast extract at a carbon source to nitrogen source ratio of 15 was required to produce 90 g/L of lactic acid in the medium containing 100 g/L of glucose. Batch fermentation of TS medium resulted in 90 g/L of lactic acid after 48 h, and the medium containing 10 % CDS resulted in 95 g/L of lactic acid after 44 h. Therefore, TS and CDS could be considered as potential alternative fermentation medium for the economical production of lactic acid. Furthermore, lactic acid fermentation was performed using only cassava and CDS for commercial production of lactic acid. The volumetric productivity of lactic acid [2.94 g/(L·h)] was 37 % higher than the productivity obtained from the medium with glucose and CDS.     

Comparative metabolic profiling-based improvement of rapamycin production by Streptomyces hygroscopicus

Rapamycin is a clinically important macrocyclic polyketide with immunosuppressive activity produced by Streptomyces hygroscopicus. To rationally guide the improvement of rapamycin production, comparative metabolic profiling analysis was performed in this work to investigate the intracellular metabolic changes in S. hygroscopicus U1-6E7 fermentation in medium M1 and derived medium M2. A correlation between the metabolic profiles and rapamycin accumulation was revealed by partial least-squares to latent structures analysis, and 16 key metabolites that most contributed to the metabolism differences and rapamycin production were identified. Most of these metabolites were involved in tricarboxylic acid cycle, fatty acids, and shikimic acid and amino acids metabolism. Based on the analysis of key metabolites changes in the above pathways, corresponding exogenous addition strategies were proposed as follows: 1.0 g/L methyl oleate was added at 0 h; 1.0 g/L lysine was added at 12 h; 0.5 g/L shikimic acid was added at 24 h; 0.5 g/L sodium succinate, 0.1 g/L phenylalanine, 0.1 g/L tryptophan, and 0.1 g/L tyrosine were added at 36 h, successively, and a redesigned fermentation medium (M3) was obtained finally on the basis of M2. The production of rapamycin in M3 was increased by 56.6 % compared with it in M2, reaching 307 mg/L at the end of fermentation (120 h). These results demonstrated that metabolic profiling analysis was a successful method applied in the rational guidance of the production improvement of rapamycin, as well as other industrially or clinically important compounds.     

Improvement of kojic acid production in Aspergillus oryzae B008 mutant strain and its uses in fermentation of concentrated corn stalk hydrolysate

A strain designated M866, producing kojic acid with a high yield, was obtained by combining induced mutation using ion beam implantation and ethyl methane sulfonate treatment of a wild type strain of Aspergillus oryzae B008. The amount of kojic acid produced by the strain M866 in a shaking flask was 40.2 g/L from 100 g/L of glucose, which was 1.7 times higher than that produced by wild strain (23.58 g/L). When the mixture of glucose and xylose was used as carbon source, the resulting kojic acid production was raised with the increasing of glucose ratios in the mixture. With concentrations of glucose at 75 g/L and xylose at 25 g/L mixed in the medium, the production of kojic acid reached 90.8 %, which was slightly lower than with glucose as the sole source of carbon. In addition, the kojic acid fermentation of the concentrated hydrolysate from corn stalk was also investigated in this study, the maximum concentration of kojic acid accumulated at the end of the fermentation was 33.1 g/L and this represents the yield based on reducing sugar consumed and the overall productivity of 0.36 g/g and 0.17 g/L/h, respectively.     

Statistical optimization of lovastatin production by Omphalotus olearius (DC.) singer in submerged fermentation

In this study, culture conditions were optimized to improve lovastatin production by Omphalotus olearius, isolate OBCC 2002, using statistical experimental designs. The Plackett–Burman design was used to select important variables affecting lovastatin production. Accordingly, glucose, peptone, and agitation speed were determined as the variables that have influence on lovastatin production. In a further experiment, these variables were optimized with a Box–Behnken design and applied in a submerged process; this resulted in 12.51 mg/L lovastatin production on a medium containing glucose (10 g/L), peptone (5 g/L), thiamine (1 mg/L), and NaCl (0.4 g/L) under static conditions. This level of lovastatin production is eight times higher than that produced under unoptimized media and growth conditions by Omphalotus olearius. To the best of our knowledge, this is the first attempt to optimize submerged fermentation process for lovastatin production by Omphalotus olearius.     

Co-fermentation of carbon sources by Enterobacter aerogenes ATCC 29007 to enhance the production of bioethanol

We investigated the enhancement of bioethanol production in Enterobacter aerogenes ATCC 29007 by co-fermentation of carbon sources such as glycerol, glucose, galactose, sucrose, fructose, xylose, starch, mannitol and citric acid. Biofuel production increases with increasing growth rate of microorganisms; that is why we investigated the optimal growth rate of E. aerogenes ATCC 29007, using mixtures of different carbon sources with glycerol. E. aerogenes ATCC 29007 was incubated in media containing each carbon source and glycerol; growth rate and bioethanol production improved in all cases compared to those in medium containing glycerol alone. The growth rate and bioethanol production were highest with mannitol. Fermentation was carried out at 37 °C for 18 h, pH 7, using 50 mL defined production medium in 100 mL serum bottles at 200 rpm. Bioethanol production under optimized conditions in medium containing 16 g/L mannitol and 20 g/L glycerol increased sixfold (32.10 g/L) than that containing glycerol alone (5.23 g/L) as the carbon source in anaerobic conditions. Similarly, bioethanol production using free cells in continuous co-fermentation also improved (27.28 g/L) when 90.37 % of 16 g/L mannitol and 67.15 % of 20 g/L glycerol were used. Although naturally existing or engineered microorganisms can ferment mixed sugars sequentially, the preferential utilization of glucose to non-glucose sugars often results in lower overall yield and productivity of ethanol. Here, we present new findings in E. aerogenes ATCC 29007 that can be used to improve bioethanol production by simultaneous co-fermentation of glycerol and mannitol.     

Studies on the production of shikimic acid using the <Emphasis Type="Italic">aroK</Emphasis> knockout strain of <Emphasis Type="Italic">Bacillus megaterium</Emphasis>

Shikimic acid has various pharmaceutical and industrial applications. It is the sole chemical building block for the antiviral drug oseltamivir (Tamiflu^®) and one of the potent pharmaceutical intermediates with three chiral centres. Here we report a modified strain of Bacillus megaterium with aroK (shikimate kinase) knock out to block the aromatic biosynthetic pathway downstream of shikimic acid. Homologous recombination based gene disruption approach was used for generating aroK knock out mutant of B. megaterium. Shake flask cultivation showed shikimic acid yield of 2.98 g/L which is ~6 times more than the wild type (0.53 g/L). Furthermore, the shikimate kinase activity was assayed and it was 32 % of the wild type. Effect of various carbon sources on the production of shikimic acid was studied and fructose (4 %, w/v) was found to yield maximum shikimic acid (4.94 g/L). The kinetics of growth and shikimic acid production by aroK knockout mutant was studied in 10 L bioreactor and the yield of shikimic acid had increased to 6 g/L which is ~12 fold higher over the wild type. It is evident from the results that aroK gene disruption had an immense effect in enhancing the shikimic acid production.     

Metabolic engineering of Aspergillus oryzae NRRL 3488 for increased production of l-malic acid

Malic acid, a petroleum-derived C4-dicarboxylic acid that is used in the food and beverage industries, is also produced by a number of microorganisms that follow a variety of metabolic routes. Several members of the genus Aspergillus utilize a two-step cytosolic pathway from pyruvate to malate known as the reductive tricarboxylic acid (rTCA) pathway. This simple and efficient pathway has a maximum theoretical yield of 2 mol malate/mol glucose when the starting pyruvate originates from glycolysis. Production of malic acid by Aspergillus oryzae NRRL 3488 was first improved by overexpression of a native C4-dicarboxylate transporter, leading to a greater than twofold increase in the rate of malate production. Overexpression of the native cytosolic alleles of pyruvate carboxylase and malate dehydrogenase, comprising the rTCA pathway, in conjunction with the transporter resulted in an additional 27 % increase in malate production rate. A strain overexpressing all three genes achieved a malate titer of 154 g/L in 164 h, corresponding to a production rate of 0.94 g/L/h, with an associated yield on glucose of 1.38 mol/mol (69 % of the theoretical maximum). This rate of malate production is the highest reported for any microbial system.     

Fumaric Acid Production by <Emphasis Type="Italic">Rhizopus oryzae</Emphasis> ATCC® 20344™ from Lignocellulosic Syrup

Powdered activated carbon-treated lignocellulosic syrup prepared from energy cane bagasse was evaluated as a potential feedstock in the production of fumaric acid by Rhizopus oryzae ATCC® 20344?. Energy cane bagasse was pretreated with dilute ammonia and enzymatically hydrolyzed with commercially available enzymes, Cellic® CTec2 and HTec2. The collected hydrolysate samples were subjected to powdered activated carbon adsorption for the removal of non-sugar compounds (i.e., organic acids, furaldehydes, total phenolic compounds) and concentrated to a final 65°Bx syrup (mostly xylose and glucose sugars). The use of lignocellulosic syrup, the effect of nitrogen source, medium additives, and initial pH in the seed culture medium on fungal morphology were investigated. The carbon to nitrogen (C/N) ratio in the acid production medium was also optimized for maximum yields in fumaric acid production. Optimum seed culture medium conditions (2.0 g/L urea, 3.0 pH) produced the desired compact, smooth, and uniform fungal pellets. Optimum acid production medium conditions (400 C/N ratio, 0.2 g/L urea) resulted in a fumaric acid production of 34.20 g/L, with a yield of 0.43 g/g and a productivity of 0.24 g/L/h. These results were comparable to those observed with the control medium (pure glucose and xylose). The present study demonstrated that lignocellulosic syrup processed from dilute ammonia pretreated energy cane bagasse has potential as a renewable carbon source for fumaric acid fermentation by Rhizopus oryzae ATCC® 20344?.     

Succinic acid production from Bacteroides fragilis: process optimization and scale up in a bioreactor

We report the effect of different physiological and nutritional parameters on succinic acid production from Bacteroides fragilis. This strain initially produced 0.70gL(-1) of succinic acid in 60h. However, when process optimization was employed, 5.4gL(-1) of succinic acid was produced in medium consisting of glucose (1.5%); tryptone (2.5%); Na(2)CO(3) (1.5%), at pH 7.0, when inoculated with 4% inoculum and incubated at 37 degrees C, 100rpm for 48h. A marked enhancement in succinic acid production was observed when the optimized conditions were employed in a 10L bioreactor. A total of 12.5gL(-1) of succinic acid was produced in 30h. This is approximately 12-fold increase in succinic acid production when compared to the initial un-optimized medium production. This enhancement in succinic acid production may be due to the control of CO(2) supply and the impeller speed. This is also resulted in the reduction of the production time. The present study provides useful information to the industrialists seeking environmentally benign technology for the production of bulk biomolecules through manipulation of various chemical parameters.     

An integrative process of bioconversion of oil palm empty fruit bunch fiber to ethanol with on-site cellulase production

The aim of this study was to efficiently convert oil palm empty fruit bunch fiber (OPEFB), one of the most commonly generated lingo-wastes in Southeast Asia, into both cellulase and bioethanol. The unprocessed cellulase crude (37.29 %) produced under solid-state fermentation using OPEFB as substrate showed a better reducing sugar yield using filter paper than the commercial enzyme blend (34.61 %). Organosolv pretreatment method could efficiently reduce hemicellulose (24.3–18.6 %) and lignin (35.2–22.1 %) content and increase cellulose content (40.5–59.3 %) from OPEFB. Enzymatic hydrolysis of pretreated OPEFB using the crude cellulase with 20 % solid content, enzyme loading of 15 FPU/g OPEFB at 50 °C, and pH 5.5 resulted in a OPEFB hydrolysate containing 36.01 g/L glucose after 72 h. Fermentation of the hydrolysate medium produced 17.64 g/L ethanol with 0.49 g/g yield from glucose and 0.088 g/g yield from OPEFB at 8 h using Saccharomyces cerevisiae.     

Efficient production of l-lactic acid by newly isolated thermophilic Bacillus coagulans WCP10-4 with high glucose tolerance

A thermophilic Bacillus coagulans WCP10-4 with tolerance to high concentration of glucose was isolated from soil and used to produce optically pure l-lactic acid from glucose and starch. In batch fermentation at pH?6.0, 240 g/L of glucose was completely consumed giving 210 g/L of l-lactic acid with a yield of 95 % and a productivity of 3.5 g/L/h. In simultaneous saccharification and fermentation at 50 °C without sterilizing the medium, 200 g/L of corn starch was completely consumed producing 202.0 g/L of l-lactic acid. To the best of our knowledge, this strain shows the highest osmotic tolerance to glucose among the strains ever reported for lactic acid production. This is the first report of simultaneous saccharification and fermentation of starch for lactic acid production under a non-sterilized condition.     

Enhanced butanol production by optimization of medium parameters using Clostridium acetobutylicum YM1

A new isolate of the solvent-producing Clostridium acetobutylicum YM1 was used to produce butanol in batch culture fermentation. The effects of glucose concentration, butyric acid addition and C/N ratio were studied conventionally (one-factor-at-a-time). Moreover, the interactions between glucose concentration, butyric acid addition and C/N ratio were further investigated to optimize butanol production using response surface methodology (RSM). A central composite design was applied, and a polynomial regression model with a quadratic term was used to analyze the experimental data using analysis of variance (ANOVA). ANOVA revealed that the model was highly significant (p < 0.0001) and the effects of the glucose and butyric acid concentrations on butanol production were significant. The model validation experiment showed 13.82 g/L butanol was produced under optimum conditions. Scale up fermentation in optimized medium resulted in 17 g/L of butanol and 21.71 g/L of ABE. The experimental data of scale up in 5 L bioreactor and flask scale were fitted to kinetic mathematical models published in the literature to estimate the kinetic parameters of the fermentation. The models used gave the best fit for butanol production, biomass and glucose consumption for both flask scale and bioreactor scale up.     

Schizophyllan production by newly isolated fungus <Emphasis Type="Italic">Schizophyllum commune</Emphasis> IBRC-M 30213: optimization of culture medium using response surface methodology

Schizophyllan (SPG) is a commercially attractive biopolymer produced by Schizophyllum commune. An investigation on the potential for SPG production by Iranian native S. commune was conducted based on culture medium, fermentation conditions and bioreactor type, . Nine native fungal strains were isolated from the northern forest of Iran at different times. Based on growth rate and SPG production, one strain was selected for further study. Optimal medium composition and inoculum size for maximizing SPG production and minimizing biomass were determined using central composite design by setting sucrose, yeast extract, inoculum size, carboxymethyl cellulose and oleic acid in the ranges of 50–200 g/L, 1–4 g/L, 2–10%, 2–12 g/L and 0.032–0.222%, respectively. The results showed that optimal results were obtained at 93.47 g/L sucrose, 1.87 g/L yeast extract, 7.68% inoculum size, 9.07 g/L carboxymethyl cellulose and 0.13% oleic acid, with maximum SPG production of 9.97 g/L and minimum biomass of 35.18 g/L. Under these optimal conditions, the production of SPG was studied in stirred tank and bubble column bioreactors. The results revealed greater production in the stirred tank because of better mixing of the culture medium. The SPG produced was characterized using rheometery, Fourier transform infrared spectroscopy, nuclear magnetic resonance), scanning electron microscopy and gel permeation chromatography. The results of these characterizations demonstrated the similarity of the SPG produced by S. commune IBRC-M 30213 to commercial SPG. Thus, the SPG produced shows good potential as a polysaccharide for use in various industries.     

Conversion of acid hydrolysate of oil palm empty fruit bunch to L-lactic acid by newly isolated Bacillus coagulans JI12

Cost-effective conversion of lignocellulose hydrolysate to optically pure lactic acid is commercially attractive but very challenging. Bacillus coagulans JI12 was isolated from natural environment and used to produce L-lactic acid (optical purity?>?99.5 %) from lignocellulose sugars and acid hydrolysate of oil palm empty fruit bunch (EFB) at 50 °C and pH 6.0 without sterilization of the medium. In fed-batch fermentation with 85 g/L initial xylose and 55 g/L xylose added after 7.5 h, 137.5 g/L lactic acid was produced with a yield of 98 % and a productivity of 4.4 g/L?h. In batch fermentation of a sugar mixture containing 8.5 % xylose, 1 % glucose, and 1 % L-arabinose, the lactic acid yield and productivity reached 98 % and 4.8 g/L?h, respectively. When EFB hydrolysate was used, 59.2 g/L of lactic acid was produced within 9.5 h at a yield of 97 % and a productivity of 6.2 g/L?h, which are the highest among those ever reported from lignocellulose hydrolysates. These results indicate that B. coagulans JI12 is a promising strain for industrial production of L-lactic acid from lignocellulose hydrolysate.     

Production of succinic acid and lactic acid by Corynebacterium crenatum under anaerobic conditions

A new succinic acid and lactic acid production bioprocess by Corynebacterium crenatum was investigated in mineral medium under anaerobic conditions. Corynebacterium crenatum cells with sustained acid production ability and high acid volumetric productivity harvested from the glutamic acid fermentation broth were used to produce succinic acid and lactic acid. Compared with the first cycle, succinic acid production in the third cycle increased 120% and reached 43.4 g/L in 10 h during cell-recycling repeated fermentations. The volumetric productivities of succinic acid and lactic acid could maintain above 4.2 g/(L·h) and 3.1 g/(L·h), respectively, for at least 100 h. Moreover, wheat bran hydrolysates could be used for succinic acid and lactic acid production by the recycled C. crenatum cells. The final succinic acid concentration reached 43.6 g/L with a volumetric productivity of 4.36 g/(L·h); at the same time, 32 g/L lactic acid was produced.     

Metabolic flux analysis of Gluconacetobacter xylinus for bacterial cellulose production

Metabolic flux analysis was used to reveal the metabolic distributions in Gluconacetobacter xylinus (CGMCC no. 2955) cultured on different carbon sources. Compared with other sources, glucose, fructose, and glycerol could achieve much higher bacterial cellulose (BC) yields from G. xylinus (CGMCC no. 2955). The glycerol led to the highest BC production with a metabolic yield of 14.7 g/mol C, which was approximately 1.69-fold and 2.38-fold greater than that produced using fructose and glucose medium, respectively. The highest BC productivity from G. xylinus CGMCC 2955 was 5.97 g BC/L (dry weight) when using glycerol as the sole carbon source. Metabolic flux analysis for the central carbon metabolism revealed that about 47.96 % of glycerol was transformed into BC, while only 19.05 % of glucose and 24.78 % of fructose were transformed into BC. Instead, when glucose was used as the sole carbon source, 40.03 % of glucose was turned into the by-product gluconic acid. Compared with BC from glucose and fructose, BC from the glycerol medium showed the highest tensile strength at 83.5 MPa, with thinner fibers and lower porosity. As a main byproduct of biodiesel production, glycerol holds great potential to produce BC with superior mechanical and microstructural characteristics.     

Optimization of Dilute Acid Pretreatment and Enzymatic Hydrolysis of <Emphasis Type="Italic">Phalaris aquatica</Emphasis> L. Lignocellulosic Biomass in Batch and Fed-Batch Processes

Phalaris aquatica L., a rich in holocellulose (69.80 %) and deficient in lignin (6.70 %) herbaceous, perennial grass species, was utilized in a two-step (biomass pretreatment-enzymatic hydrolysis) saccharification process for sugars recovery. The Taguchi methodology was employed to determine the dilute acid pretreatment and enzymatic hydrolysis conditions that optimized hemicellulose conversion (75.04 %), minimized the production of inhibitory compounds (1.41 g/L), and maximized the cellulose to glucose yield (69.69 %) of mixed particulate biomass (particles <1000 μm) under batch conditions. The effect of biomass particle size on saccharification process efficiency was also investigated. It was found that small-size biomass particles (53–106 μm) resulted in maximum hemicellulose conversion (81.12 %) and cellulose to glucose yield (93.24 %). The determined optimal conditions were then applied to a combined batch pretreatment process followed by a fed-batch enzymatic hydrolysis process that maximized glucose concentration (62.24 g/L) and yield (92.48 %). The overall efficiency of the saccharification process was 88.13 %.     

Metabolic modeling and response surface analysis of an Escherichia coli strain engineered for shikimic acid production

Background

Classic metabolic engineering strategies often induce significant flux imbalances to microbial metabolism, causing undesirable outcomes such as suboptimal conversion of substrates to products. Several mathematical frameworks have been developed to understand the physiological and metabolic state of production strains and to identify genetic modification targets for improved bioproduct formation. In this work, a modeling approach was applied to describe the physiological behavior and the metabolic fluxes of a shikimic acid overproducing Escherichia coli strain lacking the major glucose transport system, grown on complex media.

Results

The obtained flux distributions indicate the presence of high fluxes through the pentose phosphate and Entner-Doudoroff pathways, which could limit the availability of erythrose-4-phosphate for shikimic acid production even with high flux redirection through the pentose phosphate pathway. In addition, highly active glyoxylate shunt fluxes and a pyruvate/acetate cycle are indicators of overflow glycolytic metabolism in the tested conditions. The analysis of the combined physiological and flux response surfaces, enabled zone allocation for different physiological outputs within variant substrate conditions. This information was then used for an improved fed-batch process designed to preserve the metabolic conditions that were found to enhance shikimic acid productivity. This resulted in a 40% increase in the shikimic acid titer (60 g/L) and 70% increase in volumetric productivity (2.45 gSA/L*h), while preserving yields, compared to the batch process.

Conclusions

The combination of dynamic metabolic modeling and experimental parameter response surfaces was a successful approach to understand and predict the behavior of a shikimic acid producing strain under variable substrate concentrations. Response surfaces were useful for allocating different physiological behavior zones with different preferential product outcomes. Both model sets provided information that could be applied to enhance shikimic acid production on an engineered shikimic acid overproducing Escherichia coli strain.

     

出芽短梗霉产聚苹果酸发酵条件的优化

【背景】出芽短梗霉可发酵葡萄糖生成聚苹果酸,但存在转化率和转化效率低等瓶颈,阻碍其实现商业化生产。【目的】通过优化发酵培养条件,提高出芽短梗霉的聚苹果酸产量、糖酸转化率和生产强度。【方法】采用单因素试验优化适宜出芽短梗霉BK-10菌株产生聚苹果酸的培养条件,通过Plackett-Burman法对培养基组分筛选显著性影响因素,并对其培养基中无机盐进行正交试验优化,最后进行5 L发酵罐验证。【结果】最优培养基配方和培养条件:100 g/L葡萄糖,1.5 g/L尿素,0.20 g/L KH_2PO_4,0.20 g/L ZnSO_4,0.05 g/L MgSO_4,0.75 g/L KCl,30 g/L CaCO_3,0.01%吐温-80,发酵温度26°C,250 mL摇瓶装液量50 mL。【结论】通过优化,聚苹果酸的糖酸转化率达到0.71 g/g,生产强度达到0.89 g/(L·h),较优化前分别提高了18.33%和71.15%,为发酵葡萄糖合成聚苹果酸进而生产L-苹果酸工艺的工业化生产奠定经济性基础。     

Optimization of nutritional supplements for enhanced lactic acid production utilizing sugar refinery by-products

The present study investigated the synergistic effect of nutritional supplements (amino acid and Tween 80) on lactic acid production by Lactobacillus delbruckii utilizing a sugar refinery by product (cane molasses) in a submerged fermentation process. Initially, the effect of individual factors on lactic acid yield was studied by supplementing amino acids and their combinations, Tween 80 and cane molasses at varying concentrations in production medium. A combination of l-phenylalanine and l-lysine gave a maximum lactic acid yield of 47.89?±?0.1 g/L on a dry cell weight basis at individual factor level. Similarly, maximum lactic acid yield was obtained by supplementing the production medium with 40.0 g/L and 2.0 g/L Tween 80 and cane molasses, respectively, at individual factor level. In order to further improve the lactic acid yield, nutritional supplements were optimized by central composite rotatable design (CCRD) using Minitab 15 software. Shake flask cultivation under optimized conditions, i.e., cane molasses (32.40 g/L), Tween 80 (2.0 g/L) and l-phenylalanine and l-lysine (34.0 mg/L) gave a lactic acid yield of 64.86?±?0.2 g/L, corresponding to 95.0 % of the predicted yield of 67.78?±?0.3 g/L. Batch cultivation performed in 7.5 L bioreactor (working volume: 3.0 L) under optimized conditions gave maximum lactic acid yield and productivity of 79.12?±?0.2 g/L and 3.40 g/L·h, which is higher than previous studies with reduced fermentation time. Screening of lactic acid producing bacteria and characterization of lactic acid was also done.