A multi-laboratory comparative study of spore trap analyses

Fungal spore trap analyses currently are being marketed to the medical and environmental industries as a means of evaluating fungal bioaerosols. No studies comparing the results of these analyses have been conducted among laboratories providing these services. In the current study we compared the results from seven such laboratories with four different commercial spore trap cassettes with samples from four environmental conditions. The conditions included indoor air from a single location in a building under low, moderate and high agitation, and a sample from outside the same building. The means, ranges and standard deviations of total spore counts per cubic meter were respectively: low agitation indoor 514, 40-1933, 395; moderate agitation indoor 446, 80-1120, 290; high agitation indoor, 5154, 1510-15278, 3335; and outdoor 16012, 3700-28959, 6600. Results were similarly variable for the 27 spore categories that contribute to the total count. No consistent difference was observed in the precision of the kinds of spore traps. We concluded that spore trap analyses should be used with caution and should not be used as a sole method of assessing fungal spore populations and that standardized methods of analysis must be developed that include information about analytical precision of the sample data.     

Long-term use of high-efficiency vacuum cleaners and residential airborne fungal-spore exposure

Exposure to fungal allergens is an important contributor to allergic respiratory disease, but information on the efficacy of residential fungal allergen-avoidance in allergic-disease management is lacking. Using vacuum cleaners with high-efficiency exhaust filtration is one method recommended for reducing residential allergen exposure levels, but their use to reduce fungal-spore exposure levels has not been evaluated. To evaluate the effectiveness of high-efficiency vacuuming to control airborne fungal-spore levels, fungal bioaerosols were repeatedly assessed over the course of 10 months in homes randomly assigned to groups using either conventionally filtered (control) or high-efficiency-filtered vacuum cleaners for routine vacuum cleaning. Air samples were analyzed for three fungal-spore categories representing taxa with predominantly outdoor sources and one representing taxa that commonly have indoor sources. In a two-way analysis of variance, sampling period had a significant effect on mean levels of all fungal-spore categories. Vacuum cleaner type had a marginally significant effect on the indoor spore category, with one high-efficiency vacuum group mean (of three) significantly lower than one control mean. No effect was observed of vacuum cleaner type on outdoor spore categories. Including home-environment variables in analysis of covariance models strengthened the effect of the vacuum-type treatment on the indoor spore category, with no effect on the three outdoor spore categories. Decreased indoor spore levels vs. controls were only observed in high-efficiency vacuum groups during the last sampling period, at the end of the heating season. The results suggest that using a vacuum with high-efficiency filtered exhaust could have some modest effectiveness in controlling airborne fungal-spore exposure in homes when infiltration of outdoor air is very limited.     

Long-term use of high-efficiency vacuum cleaners and residential airborne fungal-spore exposure

Exposure to fungal allergens is an important contributor to allergic respiratory disease, but information on the efficacy of residential fungal allergen-avoidance in allergic-disease management is lacking. Using vacuum cleaners with high-efficiency exhaust filtration is one method recommended for reducing residential allergen exposure levels, but their use to reduce fungal-spore exposure levels has not been evaluated. To evaluate the effectiveness of high-efficiency vacuuming to control airborne fungal-spore levels, fungal bioaerosols were repeatedly assessed over the course of 10 months in homes randomly assigned to groups using either conventionally filtered (control) or high-efficiency-filtered vacuum cleaners for routine vacuum cleaning. Air samples were analyzed for three fungal-spore categories representing taxa with predominantly outdoor sources and one representing taxa that commonly have indoor sources. In a two-way analysis of variance, sampling period had a significant effect on mean levels of all fungal-spore categories. Vacuum cleaner type had a marginally significant effect on the indoor spore category, with one high-efficiency vacuum group mean (of three) significantly lower than one control mean. No effect was observed of vacuum cleaner type on outdoor spore categories. Including home-environment variables in analysis of covariance models strengthened the effect of the vacuum-type treatment on the indoor spore category, with no effect on the three outdoor spore categories. Decreased indoor spore levels vs. controls were only observed in high-efficiency vacuum groups during the last sampling period, at the end of the heating season. The results suggest that using a vacuum with high-efficiency filtered exhaust could have some modest effectiveness in controlling airborne fungal-spore exposure in homes when infiltration of outdoor air is very limited.     

Considerations in the grouping of plant and fungal taxa for an epidemiologic study

Although exposure to airborne pollen grains and fungal spores has been implicated as a causative factor for acute exacerbation of asthma, the few epidemiologic studies that have attempted to evaluate the relationship between these bioaerosols and asthma have used only total counts (ignoring the relative importance of different taxa) or a few predominant pollen or spore types (ignoring less abundant but potentially relevant groups). This paper reports the development of hypothesis‐driven exposure metrics (based on known aeroallergen associations with allergic asthma and other hypersensitivity diseases, pollen allergen cross‐reactivity, and the presence of local sources in the city of Fresno, California, USA) for a 3.5 year epidemiologic study of childhood asthma. Outdoor regional and neighborhood concentrations of pollen and spores were measured using Hirst‐type, 7‐day samplers. Indoor and outdoor residential concentrations were measured at 84 selected homes with similar 24‐hour slit impactors. All pollen and spore concentrations were recorded in 2‐hour intervals to assist in understanding diurnal fluctuations in aeroallergen concentrations, identify exposures during the time periods that children are outdoors, and study interaction between aeroallergens and other air contaminants, which were the primary focus of the study. The 124 pollen taxa that were observed were reduced to 15 categories and the 66 fungal and algal taxa were reduced to five categories that will be used in microenvironmental models to generate individual daily exposure estimates for each of the 315 children. These new exposure metrics will allow examination of health effects for taxa traditionally associated with allergy and those with locally elevated concentrations in combination with exposures to other indoor and outdoor air contaminants.     

Fungal spore attachment to substrata

A critical factor in the success of fungal growth is spore adhesion to host surfaces. Generating spores capable of rapid and firm bonding to their hosts is not only important for keeping spores from prematurely detaching from the host surface but can also serve as a trigger for spore germination and the development of infection structures. In this paper fungal spore adhesion mechanisms are reviewed as well as factors influencing spore adhesion, germination, and differentiation. This review ends with a brief discussion on the future of fungal adhesion research.     

Treatment of Fungal Bioaerosols by a High-Temperature,Short-Time Process in a Continuous-Flow System

Airborne fungi, termed fungal bioaerosols, have received attention due to the association with public health problems and the effects on living organisms in nature. There are growing concerns that fungal bioaerosols are relevant to the occurrence of allergies, opportunistic diseases in hospitals, and outbreaks of plant diseases. The search for ways of preventing and curing the harmful effects of fungal bioaerosols has created a high demand for the study and development of an efficient method of controlling bioaerosols. However, almost all modern microbiological studies and theories have focused on microorganisms in liquid and solid phases. We investigated the thermal heating effects on fungal bioaerosols in a continuous-flow environment. Although the thermal heating process has long been a traditional method of controlling microorganisms, the effect of a continuous high-temperature, short-time (HTST) process on airborne microorganisms has not been quantitatively investigated in terms of various aerosol properties. Our experimental results show that the geometric mean diameter of the tested fungal bioaerosols decreased when they were exposed to increases in the surrounding temperature. The HTST process produced a significant decline in the (1→3)-β-d-glucan concentration of fungal bioaerosols. More than 99% of the Aspergillus versicolor and Cladosporium cladosporioides bioaerosols lost their culturability in about 0.2 s when the surrounding temperature exceeded 350°C and 400°C, respectively. The instantaneous exposure to high temperature significantly changed the surface morphology of the fungal bioaerosols.Fungi are omnipresent in indoor and outdoor environments (2, 28, 39). Most fungi are dispersed through the release of spores into the air, a phenomenon known to be driven by two kinds of energy (17): the energy provided by the fungus itself and the energy provided by external sources, such as air currents, rain, gravity, or changes in temperature and nutritional sources. Of these various mechanisms of fungal particle release, dispersal by air currents is the most prevalent mechanism for indoor fungal particles (19, 31). These airborne fungal spores, termed fungal bioaerosols, are resistant to environmental stresses and are adapted to airborne transport.Fungal bioaerosols constitute the major component of ambient airborne microorganisms (23, 50, 51). Several studies have reported that the concentration of fungal bioaerosols is relevant to the occurrence of human diseases and public health problems associated with acute toxic effects, allergies (3, 18), and asthma (4, 5, 13, 48). Fungal bioaerosols are of particular concern in healthcare facilities, where they can cause major infectious complications as opportunistic pathogens in patients with an immunodeficiency (9). For instance, invasive mycoses can affect patients undergoing high-dose chemotherapy for hematological malignancies associated with a prolonged period of neutropenia; they can also affect solid-organ transplant recipients. Despite all diagnostic and therapeutic efforts, the outcome of an invasive fungal infection is often fatal (with a mortality rate of around 50% for aspergillosis) (37). The main fungal genera responsible for these infections are as follows: Aspergillus spp., Fusarium spp., Scedosporium spp., and Mucorales spp. (10, 12, 20). However, virtually any filamentous fungus can be a pathogen (22, 41). In the hospital environment, possible sources of airborne nosocomial infection include ventilation or air-conditioning systems, decaying organic material, dust, water, food, ornamental plants, and building materials in and around hospitals (1).One of the major bioaerosols of concern is (1→3)-β-d-glucans, which comprises up to 60% of the cell wall of most fungal organisms. The (1→3)-β-d-glucans are glucose polymers with a variable molecular weight and a degree of branching (49). The results of several studies about the exposure of subjects to airborne (1→3)-β-d-glucans suggest that these agents play a role in bioaerosol-induced inflammatory responses and resulting respiratory symptoms, such as a dry cough, phlegmy cough, hoarseness, and atopy (11, 44). In addition, given that many epidemiological studies have reported that (1→3)-β-d-glucan has strong immuno-modulating effects (42, 47), (1→3)-β-d-glucan is an important parameter for exposure assessment by itself and as a surrogate component for fungi (16).To prevent the adverse health effects of fungal bioaerosols, we must ensure that control methods for airborne fungal spores are studied and developed. However, despite the necessity of controlling fungal bioaerosols, few studies have focused on such control mechanisms. The most common control methods are UV irradiation and electric ion emission. Given that UV irradiation is known to have a germicidal effect, several studies have examined how UV irradiation affects the viability of bioaerosols (35, 42). However, although UV irradiation can be easily applied by simply installing and turning on a UV lamp, the 254-nm-wavelength UV light produces ozone and radicals, which cause harmful effects to surrounding humans. Electric ion emission has also been studied as a means of controlling bioaerosols (21, 27). When the efficiency of the filter is increased, the efficacy of respiratory protection devices against bioaerosols can be enhanced. Although electric ions decrease the viability of airborne bacteria (25), the generation of the ions produces ozone, a pollutant, and also causes electric charges to accumulate on surrounding surfaces.Recently, heat treatment of indoor air using thermal processes has been considered a safe, effective, and environment-friendly method; it does not produce ozone or use ion or filter media. A thermal heating process has long been considered a suitable and reliable method for controlling microorganisms. Two types of heat are generally used, moist heat and dry heat. Moist heat utilizes steam under pressure, whereas dry heat involves high-temperature exposure without additional moisture. Several types of heat treatment are currently used for killing microorganisms. The treatments include incineration, Tyndallization, pasteurization, and autoclaving (32). However, most of these technologies were originally limited to controlling microorganisms in liquid or on material surfaces. In addition, they may not be adequate for controlling bioaerosols because the continuous surrounding environment of bioaerosols is significantly different from the conditions in liquid and on solid surfaces. Therefore, it is necessary to find adequate and practical conditions for controlling bioaerosols. Thus far, several investigations regarding the use of thermal processes against bioaerosols have been reported. Some of these studies have targeted airborne bacteria spores widely used as surrogates for biological warfare agents (8, 34), while others have focused on environmental parameters for the culture and survival of various vegetative cells (14, 29, 46). However, in these studies novel techniques for aerosols, such as measuring and analyzing aerosol particle size, distributions, and concentrations, were not utilized. In addition, to the best of our knowledge, there has been no study on the use of a thermal process for controlling fungal bioaerosols in continuous airflow. Fungal bioaerosols were found to be very resistant to a thermal environment in previous studies.In this study, we investigated the thermal heating effects on the physical, chemical, and biological properties of fungal bioaerosols using a high-temperature, short-time (HTST) sterilization process. The HTST process, a type of thermal heating process, is based on high-temperature stresses for very short periods. Although this thermal process has been used for the microbial decontamination of seeds and dried, powdered products, such as pharmaceuticals and heat-sensitive drink and food, it can be also applied to the control of an airborne microorganism in a continuous-flow system, such as a heating, ventilation, and air-conditioning system (15, 33, 38). When the fungal bioaerosol was passed through a thermal electric heating system, the fungal spores were exposed to various temperatures for short periods. Then, we examined the bioaerosol and aerosol characteristics, including aerosol size distribution, culturability, (1→3)-β-d-glucan production, and surface morphology, using a novel technique for sampling and measuring aerosols.     

Survival of microorganisms on antimicrobial filters and the removal efficiency of bioaerosols in an environmental chamber

Exposure to bioaerosols causes various adverse health effects including infectious and respiratory diseases, and hypersensitivity. Controlling exposure to bioaerosols is important for disease control and prevention. In this study, we evaluated the efficacies of various functional filters coated with antimicrobial chemicals in deactivating representative microorganisms on filters or as bioaerosols. Tested functional filters were coated with different chemicals that included (i) Ginkgo and sumac, (ii) Ag-apatite and guanidine phosphate, (iii) SiO2, ZnO, and Al2O3, and (iv) zeolite. To evaluate the filters, we used a model ventilation system (1) to evaluate the removal efficiency of bacteria (Escherichia coli and Legionella pneumophila), bacterial spores (Bacillus subtilis spore), and viruses (MS2 bacteriophage) on various functional filters, and (2) to characterize the removal efficiency of these bioaerosols. All experiments were performed at a constant temperature of 25 degrees C and humidity of 50%. Most bacteria (excluding B. subtilis) rapidly decreased on the functional filter. Therefore, we confirmed that functional filters have antimicrobial effects. Additionally, we evaluated the removal efficiency of various bioaerosols by these filters. We used a six-jet collision nebulizer to generate microbial aerosols and introduced it into the environmental chamber. We then measured the removal efficiency of functional filters with and without a medium-efficiency filter. Most bioaerosol concentrations did not significantly decrease by the functional filter only but decreased by a combination of functional and medium-efficiency filter. In conclusion, functional filters could facilitate biological removal of various bioaerosols, but physical removal of these by functional was minimal. Proper use of chemical-coated filter materials could reduce exposure to these agents.     

Pollen and fungal spore sampling and analysis. Statistical evaluations

Statistical evaluations of samples obtained from a Burkard seven-day recording volumetric pollen/spore trap were performed to determine the precision of the sampling and analysis procedures. The reproducibility of co-located traps was also investigated. The results showed that pollen grain transect counting was not significantly different, while fungal spore counting produced statistically different results. There was no statistical difference in the number of pollen and fungal spores counted between the co-located samplers. Reasons for the differences in the fungal spore counts are presented.     

Diagnostics in allergic diseases by correlating pollen/fungal spore counts with patient scores of symptoms

Pollen/fungal spore counts have been performed since 1977 in Copenhagen and since 1979 in Copenhagen, Viborg, Nykobing Falster and Nykobing Mors. Four Burkard Seven Day Recording Volumetric Spore Traps were used. Fungal spore counts were performed in the same period using a BIAP Slit Sampler (placed in the Copenhagen area). The study was carried out by the Danish Asthma-Allergy Association's interdisciplinary Aerobiology Group. In 1979 at the Allergy Clinic, Copenhagen County Hospital at Lyngby, data from the pollen/fungal spore counts were compared with daily scores of 95 patients' symptoms and medicine-index. Seventy-eight patients were scored in the entire period where symptoms occurred. For diagnostic purposes of allergy to pollen and fungal spores, previous patient history and symptom scores correlated to the pollen/fungal spore counts showed similarity and to some extent supplementary corrections to the diagnosis based on previous patient history, skin tests, laboratory tests, and provocation tests.     

山西历山珍稀药用植物AM真菌资源与土壤因子的关系

以山西历山自然保护区暴马丁香、连香树、南方红豆杉和领春木4种珍稀药用植物为材料,研究其根际土壤中丛枝菌根真菌(AMF)的菌根结构类型和种属分布,同时分析土壤因子与其侵染率和孢子密度的关系。结果表明:(1)暴马丁香菌根类型为中间型(I-型),连香树和领春木为重楼型(P-型),南方红豆杉为疆南星型(A-型);4种植物根际共鉴定AMF 27种,分别隶属于球囊霉属(Glomus)、无梗囊霉属(Acaulospora)、盾巨孢囊霉属(Scutellos-pora)、多孢囊霉属(Diversispora)和原囊霉属(Archaeospora)5属,其中Glomus为优势属。(2)pH与暴马丁香和领春木的侵染率和孢子密度呈正相关,但与连香树和南方红豆杉呈负相关;速效磷与暴马丁香、南方红豆杉和领春木的侵染率和孢子密度呈正相关,但与连香树呈负相关;碱解氮、有机质与暴马丁香、连香树和领春木的侵染率和孢子密度呈正相关,但与南方红豆杉呈负相关。(3)4种药用植物的菌根侵染率主要受其根际土壤碱解氮的影响,而根际AMF孢子密度主要受根际土壤pH制约。可见,历山自然保护区内AMF资源丰富,多样性程度也较高;宿主植物不同,土壤因子对其侵染率和孢子密度的影响也不同。     

Community structure of bacteria and fungi in aerosols of a pig confinement building

Modern intensive husbandry practices can create poor indoor air quality, with high levels of airborne dust, endotoxins, ammonia, and microorganisms. Air in a sow breeding barn was investigated to determine the biomass composition of bioaerosols using molecular methods supplemented with microscopic and cultivation-dependent approaches. A total of 2.7?±?0.7?×?10(7) bacterial cells?m(-3) air and 1.2?±?0.3?×?10(6) fungi spores?m(-3) were detected, corresponding to the fungal biovolume constituted 98% of the total microbial biovolume (fungal and bacterial). Fifty-two percent of all 4',6-diamidino-2-phenyl indole-stained cells were detectable with fluorescence in situ hybridization (FISH) with a general bacterial probe mixture. Quantitative FISH of the bacterial consortium revealed Firmicutes as the dominant group with Streptococcus as the major genus, while Actinobacteria constituted 10% of the detectable bacteria. Additionally, the study revealed an abundant and diverse fungal community including species not previously found in similar environments. The most abundant fungal 18S rRNA gene clone sequences identified affiliated with the Aspergillus-Eurotium cluster, but among others, species of Wallemia, Mucorales, and Russulales were detected. For both fungi and anaerobic bacteria, a hitherto undescribed diversity was found in bioaerosols from a modern sow breeding barn, which potentially could create poor indoor air quality, although their effect on the health of farmworkers and stock still is not resolved.     

Arbuscular mycorrhizal dynamics in a chronosequence of Caragana korshinskii plantations

Arbuscular mycorrhizal (AM) fungi in a chronosequence of 5–42-year-old Caragana korshinskii plantations in the semi-arid Loess Plateau region of northwestern China were investigated. AM fungi colonization, spore diversity and PCR-denatured gradient gel electrophoresis-based AM fungal SSU rRNA gene sequences were analyzed. AM fungi colonization [measured as the percent of root length (%RLC), vesicular (%VC) and arbuscular (%AC) colonization] and spore density were significantly correlated with sampling month, but not with plant age, except for %RLC. The percent of vesicular colonization was negatively correlated with soil total nitrogen and organic carbon, and spore density was negatively correlated with soil moisture and available phosphorus. Ten distinguishable AM fungal spore morphotypes, nine Glomus and one Scutellospora species, were found. Nine AM fungal Glomus phylotypes were identified by sequencing, but at each sampling time only four to six AM fungal phylotypes were detected. The AM fungal community was significantly seasonal, whereas the AM fungal species richness did not increase with plantation age. A significant change in AM fungal colonization and community composition over an annual cycle was observed in this study, and our results suggest that the changes of AM are the product of the interaction between host phenology, soil characteristics and habitat. Understanding these interactions is essential if habitat restoration is to be effective.     

An analysis of local wind and air mass directions and their impact on Cladosporium distribution using HYSPLIT and circular statistics

Ecological studies that examine species-environment relationships are often limited to several meteorological parameters, i.e. mean air temperature, relative humidity, precipitation, vapour pressure deficit and solar radiation. The impact of local wind, its speed and direction are less commonly investigated in aerobiological surveys mainly due to difficulties related to the employment of specific analytical tools and interpretation of their outputs. Identification of inoculum sources of economically important plant pathogens, as well as highly allergenic bioaerosols like Cladosporium species, has not been yet explored with remote sensing data and atmospheric models such as Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT). We, therefore, performed an analysis of 24 h intra-diurnal cycle of Cladosporium spp. spores from an urban site in connection with both the local wind direction and overall air mass direction computed by HYSPLIT. The observational method was a volumetric air sampler of the Hirst design with 1 h time resolution and corresponding optical detection of fungal spores with light microscopy. The atmospheric modelling was done using the on-line data set from GDAS with 1° resolution and circular statistical methods. Our results showed stronger, statistically significant correlation (p ≤ 0.05) between high Cladosporium spp. spore concentration and air mass direction compared to the local wind direction. This suggested that a large fraction of the investigated fungal spores had a regional origin and must be located more than a few kilometers away from the sampling point.     

Airborne fungal spores in a sawmill environment in Palakkad District, Kerala, India

Concentration of airborne fungal spores inindoor and outdoor environments of a sawmill in Palakkad district of Kerala, India was studied with Burkard Personal Slide Sampler from January to December 1997. Total spore concentration in the indoor and outdoor showed a 3:2 ratio. Higher spore count was observed in indoor in January and in outdoor in October. Thirty three fungal spore types were identified from the indoor and twenty six from the outdoor. Aspergillus/Penicillium, Cladosporium, Nigrospora, Ganoderma, `other basidiospores' and ascospores were the dominant components of the airspora. Aspergillus/Penicillium, the most dominant spore type in the indoor contributed 51.19% and Cladosporium, the most dominant spore type in the outdoor contributed 44.75% of the total spores. The study revealed high prevalence of predominantly allergenic fungal spores in the sawmill environment.     

Relevance of airborne fungi and their secondary metabolites for environmental,occupational and indoor hygiene

Airborne fungal contaminants are increasingly gaining importance in view of health hazards caused by the spores themselves or by microbial metabolites. In addition to the risk for infection, the allergenic and toxigenic properties, as well as the inflammatory effects are discussed in this review as possible health impacts of bioaerosols. A major problem is the lack of threshold values for pathogenic and non-pathogenic fungi, both in the workplace and in outdoor air. While the relevance of mycotoxins has been intensely studied in connection with contamination of food and feed, the possible respiratory uptake of mycotoxins from the air has so far not been sufficiently taken into account. Toxic secondary metabolites are expected to be present in airborne spores, and may thus occur in airborne dust and bioaerosols. Potential health risks cannot be estimated reliably unless exposure to mycotoxins is determined qualitatively and quantitatively. Microbial volatile organic compounds (MVOC) have been suggested to affect human health, causing lethargy, headache, and irritation of the eyes and mucous membranes of the nose and throat. The production of MVOC by fungi has been discussed in connection with domestic indoor microbial pollution, but the relevance of fungal metabolites in working environments remains insufficiently studied.     

Rainfall homogenizes while fruiting increases diversity of spore deposition in Mediterranean conditions

There is a lack of knowledge regarding the main factors modulating fungal spore deposition in forest ecosystems. We have described the local spatio-temporal dynamics of fungal spore deposition along a single fruiting season and its relation with fruit body emergence and rainfall events. Passive spore traps were weekly sampled during autumn and analysed by metabarcoding of the ITS2 region in combination with qPCR. There were larger compositional changes of deposited spores across sampling weeks than amongst sampling plots. Spore diversity and abundance correlated with mushroom emergence and weekly rainfall. Spore compositional changes were related to rainfall, with lower spatial compositional heterogeneity across plots during weeks with higher rainfall. Soil saprotrophs, and amongst them, puffball species, showed the strongest positive correlation with rainfall across fungal guilds. We saw high fine-scale temporal changes of deposited spores, and both mushroom emergence and rainfall may be important factors driving airborne spore deposition.     

The incidence of fungal spores in the ambient air and inside homes: Evidence from London

Little research has been carried out in London concerning fungal spore prevalence yet this information may help to elucidate geographical patterns of asthma and hay fever. Although many types of spore reach peak concentrations outdoors in late-summer, the incidences in the indoor environment may be more important through the winter because of heating and poor ventilation. Daily average concentrations of fungal spores in the ambient atmosphere were monitored with a Burkard volumetric spore trap on an exposed roof in North London from autumn 1991 until the summer of 1992. Indoor spore measurements were taken in 19 homes in the vicinity through the winter months, both by direct air sampling using a portable Burkard sampler and by dust culture. Trends in the occurrence and concentrations of fungal spores indoors and outdoors were examined. Relationships between the abundance of selected allergenic fungi and features of the houses were analysed including age of dwelling, dampness, cleanliness and presence of pets.Aspergillus andPenicillium were the most frequently occurring spore types in the homes. Overall, high spore incidence was associated with dampness and dust accumulation. The outdoor spore samples revealed generally low concentrations through the winter until March when concentrations of many types includingCladosporium, Epicoccum andAlternaria increased in abundance in response to the warmer weather. Even during the late-spring and early-summer, concentrations of most fungal spores were notably below those reported for rural sites.     

The influence of meteorological parameters on <Emphasis Type="Italic">Alternaria</Emphasis> and <Emphasis Type="Italic">Cladosporium</Emphasis> fungal spore concentrations in Beja (Southern Portugal): preliminary results

Introduction Fungal spores constitute an important fraction of bioaerosols in the atmosphere. Objectives To analyse the content of Alternaria and Cladosporium spores in the atmosphere of Beja and the effect of meteorological conditions on their concentrations. Methodology The daily and hourly data of Alternaria and Cladosporium fungal spores concentration in the atmosphere of Beja were monitored from April 12, 2012 to July 30, 2014, based on the Portuguese Aerobiology Network methodology. The influence of meteorological conditions on the studied types of fungal spore concentrations was assessed through Spearman’s correlation analysis. Results During the study period, 20,741 Alternaria spores and 320,862 Cladosporium spores were counted. In 2013, there were 5,822 Alternaria spores and 123,864 Cladosporium spores. The absolute maximum concentrations of Alternaria and Cladosporium spores were recorded on November 8, 2013, with 211 and 1301 spores/m³, respectively. Temperature, insolation and wind direction parameters showed a positive correlation with Alternaria and Cladosporium spore levels, while relative humidity and precipitation presented a negative correlation, which is statistically significant. Wind speed only showed a statistically significant positive correlation in terms of Alternaria spore levels. Conclusion Alternaria and Cladosporium spores are present in the atmospheric air of Beja throughout the year, with the highest concentration period occurring during spring and autumn. There was a clear effect of meteorological parameters on airborne concentrations of these fungal spores.     

Soil fungi invest into asexual sporulation under resource scarcity,but trait spaces of individual isolates are unique

During the last few decades, a plethora of sequencing studies provided insight into fungal community composition under various environmental conditions. Still, the mechanisms of species assembly and fungal spread in soil remain largely unknown. While mycelial growth patterns are studied extensively, the abundant formation of asexual spores is often overlooked, though representing a substantial part of the fungal life cycle relevant for survival and dispersal. Here, we explore asexual sporulation (spore abundance, size and shape) in 32 co-occurring soil fungal isolates under varying resource conditions, to answer the question whether resource limitation triggers or inhibits fungal investment into reproduction. We further hypothesized that trade-offs exist in fungal investment towards growth, spore production and size. The results revealed overall increased fungal investment into spore production under resource limitations; however, effect sizes and response types varied strongly among fungal isolates. Such isolate-specific effects were apparent in all measured traits, resulting in unique trait spaces of individual isolates. This comprehensive dataset also elucidated variability in sporulation strategies and trade-offs with fungal growth and reproduction under resource scarcity, as only predicted by theoretical models before. The observed isolate-specific strategies likely underpin mechanisms of co-existence in this diverse group of saprobic soil fungi.