The Use of Cyclic Voltammetry to Detect Biofilms formed by Pseudomonas fluorescens on Platinum Electrodes

The development of an electrochemical detector to monitor the in situ formation of biofilms is described. The detector consisted of an electrochemical cell containing three electrodes, whose response to the application of a potential profile to the working electrode was sensitive to the amount of biofilm present on the surface. The electrochemical technique used was repetitive cyclic voltammetry. Differences between the response of the uncolonised electrode and after Pseudomonas fluorescens biofilms of different ages were grown on its surface were determined. The results show that cyclic voltammetry applied to platinum electrodes can be used to detect young biofilms. The development of the shape of the voltammogram as the potential is cycled may constitute a means of providing information on the coverage of the surface. Observation of the platinum electrodes before and after the electrochemical measurements showed that even after 30 min of recycling, most of the cells were still adhered to the surface, although some may have lost viability.     

Voltammetric discrimination of mandelic acid enantiomers

We report a novel electrochemical biosensor for direct discrimination of d- and l-mandelic acid (d- and l-MA) in aqueous medium. The glassy carbon electrode (GCE) surface was modified with reduced graphene oxide (rGO) and γ-globulin (GLOB). Electrochemical characterization of the modified electrodes was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. The modified electrode surfaces were also characterized by scanning electron microscopy. Electrochemical response of the prepared electrode (GCE/rGO/GLOB) for discrimination of d- and l-MA enantiomers was investigated by cyclic voltammetry and was compared with bare GCE in the concentration range of 2 to 10 mM. Whereas the bare GCE showed no electrochemical response for the MA enantiomers, the GCE/rGO/GLOB electrode exhibited direct and selective discrimination with different oxidation potential values of 1.47 and 1.71 V and weak reduction peaks at potential values of −1.37 and −1.48 V, respectively. In addition, electrochemical performance of the modified electrode was investigated in mixed solution of d- and l-MA. The results show that the produced electrode can be used as electrochemical chiral biosensor for MA.     

Microbial Biofilm Voltammetry: Direct Electrochemical Characterization of Catalytic Electrode-Attached Biofilms

While electrochemical characterization of enzymes immobilized on electrodes has become common, there is still a need for reliable quantitative methods for study of electron transfer between living cells and conductive surfaces. This work describes growth of thin (<20 μm) Geobacter sulfurreducens biofilms on polished glassy carbon electrodes, using stirred three-electrode anaerobic bioreactors controlled by potentiostats and nondestructive voltammetry techniques for characterization of viable biofilms. Routine in vivo analysis of electron transfer between bacterial cells and electrodes was performed, providing insight into the main redox-active species participating in electron transfer to electrodes. At low scan rates, cyclic voltammetry revealed catalytic electron transfer between cells and the electrode, similar to what has been observed for pure enzymes attached to electrodes under continuous turnover conditions. Differential pulse voltammetry and electrochemical impedance spectroscopy also revealed features that were consistent with electron transfer being mediated by an adsorbed catalyst. Multiple redox-active species were detected, revealing complexity at the outer surfaces of this bacterium. These techniques provide the basis for cataloging quantifiable, defined electron transfer phenotypes as a function of potential, electrode material, growth phase, and culture conditions and provide a framework for comparisons with other species or communities.     

Electrochemical activation of electrodes for amperometric detection of nitric oxide

An open question in the literature of nitric oxide detection was investigated: does electrochemical activation account for the enhanced properties of certain presumed chemically-modified electrodes? Uniform electrodes of graphite, iridium, palladium, platinum, and ruthenium were exposed to potential cycling and then tested for amperometric response to nitric oxide to identify principles that govern electrochemical activation of nitric oxide electrodes. These electrodes were compared to similar electrodes that were not cycled. Only cycled graphite and ruthenium showed significantly increased responses. Graphite demonstrated enhanced performance after exposure to cycling potentials at which oxygen, CO₂, and soluble carbonates form, suggesting that erosion of the electrode enhanced its response by increasing the surface area accessible to nitric oxide. This may explain the performance of carbon fibers cycled to the same potentials in solutions containing metalloporphyrins. The response of ruthenium was enhanced after cycling to less extreme potentials at which soluble species do not form and at which a metallic conductive oxide, RuO₂, could lay down a stable, adherent layer on the electrode surface. Cycled ruthenium also exhibited a much greater increase in capacitance after cycling, consistent with the formation of a conductive surface layer.     

Electrochemical behavior of L-cysteine and its detection at carbon nanotube electrode modified with platinum

The electrochemical behavior of L-cysteine (CySH) on platinum (Pt)/carbon nanotube (CNT) electrode was investigated by cyclic voltammetry. CNTs used in this study were grown directly on graphite disk by chemical vapor deposition. Pt was electrochemically deposited on the activated CNT/graphite electrode by electroreduction of Pt(IV) complex ion on the surface of CNTs. Among graphite, CNT/graphite, and Pt/CNT electrodes, improved electrochemical behavior of CySH oxidation was found with Pt/CNT electrode. On the other hand, a sensitive CySH sensor was developed based on Pt/CNT/graphite electrode. A linear calibration curve can be observed in the range of 0.5 microM-0.1 mM. The detection limit of the Pt/CNT electrode is 0.3 microM (signal/nose=3). Effects of pH, scan rate, and interference of other oxidizable amino acids were also investigated and discussed. Additionally, the reproducibility, stability, and applicability of the Pt/CNT electrode were evaluated.     

Electroactivity of phototrophic river biofilms and constitutive cultivable bacteria

Electroactivity is a property of microorganisms assembled in biofilms that has been highlighted in a variety of environments. This characteristic was assessed for phototrophic river biofilms at the community scale and at the bacterial population scale. At the community scale, electroactivity was evaluated on stainless steel and copper alloy coupons used both as biofilm colonization supports and as working electrodes. At the population scale, the ability of environmental bacterial strains to catalyze oxygen reduction was assessed by cyclic voltammetry. Our data demonstrate that phototrophic river biofilm development on the electrodes, measured by dry mass and chlorophyll a content, resulted in significant increases of the recorded potentials, with potentials of up to +120 mV/saturated calomel electrode (SCE) on stainless steel electrodes and +60 mV/SCE on copper electrodes. Thirty-two bacterial strains isolated from natural phototrophic river biofilms were tested by cyclic voltammetry. Twenty-five were able to catalyze oxygen reduction, with shifts of potential ranging from 0.06 to 0.23 V, cathodic peak potentials ranging from -0.36 to -0.76 V/SCE, and peak amplitudes ranging from -9.5 to -19.4 μA. These isolates were diversified phylogenetically (Actinobacteria, Firmicutes, Bacteroidetes, and Alpha-, Beta-, and Gammaproteobacteria) and exhibited various phenotypic properties (Gram stain, oxidase, and catalase characteristics). These data suggest that phototrophic river biofilm communities and/or most of their constitutive bacterial populations present the ability to promote electronic exchange with a metallic electrode, supporting the following possibilities: (i) development of electrochemistry-based sensors allowing in situ phototrophic river biofilm detection and (ii) production of microbial fuel cell inocula under oligotrophic conditions.     

Glucose oxidase-polypyrrole electrodes synthesized in p-toluenesulfonic acid and sodium p-toluenesulfonate

Amperometric glucose biosensors have been developed based on entrapment on platinum (Pt) electrode using cyclic voltammetry technique in glucose oxidase (GOD) and pyrrole containing p-toluenesulfonic acid (pTSA) or sodium p-toluenesulfonate (NapTS) as supporting electrolyte solutions. Both of electrolyte solutions were suitable media for the formation and deposition of polypyrrole-GOD (PPy-GOD) layers on Pt substrate. Pt/PPy-GOD electrodes brought about in different morphological properties as well as different electrochemical and biochemical response. The highest responses obtained in pTSA and NapTS electrolytes were observed at pH of 4.5 and 7.0 for Pt/PPy-GOD electrodes, respectively. While linearity was observed between 0.0-1.0 mM glucose substrate for both electrodes, I(max) value of Pt/PPy-GOD(NapTS) electrode was approximately twice as high as that of Pt/PPy-GOD(pTSA) electrode as 25.4 and 14.2 microA, respectively. Five commercial drinks were tested with enzyme electrodes and compared with results obtained spectrophotometrically using glucose kit. Results revealed that Pt/PPy-GOD(NapTS) electrode exhibited better biosensor response.     

Amperometric biosensors based on dehydrogenase/NAD and heterocyclic quinones

The electrocatalytic oxidation of NADH was evaluated from cyclic voltammetry with heterocyclic quinones dissolved in a water solution. The process of oxidation is not sensitive to the nature of the electrode surface and takes place on platinum, glassy carbon or carbon electrodes. NADH and glucose sensors constructed were investigated and operated at 0 mV vs. Ag/AgCl (in saturated KCl) using single potential step chronoamperometry.     

Amperometric glucose biosensor based on adsorption of glucose oxidase at platinum nanoparticle-modified carbon nanotube electrode

A new amperometric biosensor, based on adsorption of glucose oxidase (GOD) at the platinum nanoparticle-modified carbon nanotube (CNT) electrode, is presented in this article. CNTs were grown directly on the graphite substrate. The resulting GOD/Pt/CNT electrode was covered by a thin layer of Nafion to avoid the loss of GOD in determination and to improve the anti-interferent ability. The morphologies and electrochemical performance of the CNT, Pt/CNT, and Nafion/GOD/Pt/CNT electrodes have been investigated by scanning electron microscopy, cyclic voltammetry, and amperometric methods. The excellent electrocatalytic activity and special three-dimensional structure of the enzyme electrode result in good characteristics such as a large determination range (0.1-13.5mM), a short response time (within 5s), a large current density (1.176 mA cm(-2)), and high sensitivity (91mA M(-1)cm(-2)) and stability (73.5% remains after 22 days). In addition, effects of pH value, applied potential, electrode construction, and electroactive interferents on the amperometric response of the sensor were investigated and discussed. The reproducibility and applicability to whole blood analysis of the enzyme electrode were also evaluated.     

Nanocomposite of functionalized multiwall carbon nanotubes with nafion, nano platinum, and nano gold biosensing film for simultaneous determination of ascorbic acid, epinephrine, and uric acid

A unique bimetallic, nano platinum (Pt) with nano gold (Au) on nafion (NF) incorporated with functionalized multiwall carbon nanotubes (f-MWCNTs) composite film (f-MWCNTs-NF-PtAu) was developed by the potentiostatic method. The composite film exhibits promising efficient catalytic activity towards the oxidation of mixture of biochemical compounds and simultaneous measurement of ascorbate anion, epinephrine and urate anion in aqueous buffer solution (pH 6.75). Both, the cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used for the measurement of electroanalytical properties of neurotransmitters by means of composite film modified electrodes. Well-separated voltammetric peaks were obtained for ascorbate, epinephrine and urate anions with the peak separations of 0.222 and 0.131V. The composite film can also be produced on gold and transparent semiconductor indium tin oxide electrodes for different kinds of studies such as electrochemical quartz crystal microbalance (EQCM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The incorporation of Pt and Au onto the f-MWCNTs-NF was revealed by the EQCM technique and the morphology of the film was studied using SEM, AFM and scanning electrochemical microscopy (SECM) techniques. Further, extensive studies were carried out using SECM for obtaining the surface current topographic images of composite film modified electrodes, and these indicated the presence of f-MWCNTs-NF-PtAu composite film on the electrode.     

Determination of L-cysteine in amino acid mixture and human urine by flow-injection analysis with a biamperometric detector.

Based on the electrocatalytic oxidation of cysteine at pretreated platinum electrode and the flow-injection biamperometry for irreversible couple, a novel electrochemical detector is proposed for the selective determination of cysteine in amino acid mixtures and human urine samples. A thin-layer flow through cell was used to achieve large electrode surface area to volume ratio. Two identical pretreated platinum electrodes were mounted in the cell with an applied potential difference of 10 mV. By coupling two independent and irreversible electrode processes, namely, the oxidation of cysteine and the reduction of platinum oxide, the biamperometric detection scheme has been established. The resulting current is linear to cysteine over the range 4 x 10(-7)-4 x 10(-5) M with the detection limit 1 x 10(-7) M (15 pmol). The selectivity of the detector is tested by 55 foreign species including 26 ions, 11 amino acids, 6 vitamins, and 12 other compounds possibly found in urine. The detector performs well as a routine assay, showing high efficiency (180 samples/h) and good reproductivity shown by a RSD of 0.6% for eight repeated determinations of 2 x 10(-6) M cysteine. The urine samples are detected directly without the need of pretreatment or adding other reagents.     

Electrochemical checking of aerobic isolates from electrochemically active biofilms formed in compost

Aims:  To design a cyclic voltammetry (CV) procedure to check the electrochemical activity of bacterial isolates that may explain the electrochemical properties of biofilms formed in compost.
Methods and Results:  Bacteria catalysing acetate oxidation in garden compost were able to form electrochemically active biofilms by transferring electrons to an electrode under chronoamperometry. They were recovered from the electrode surface and identification of the isolates using 16S rRNA sequencing showed that most of them were Gammaproteobacteria, mainly related to Enterobacter and Pseudomonas spp. A CV procedure was designed to check the electrochemical activity of both groups of isolates. Preliminary CVs suggested that the bacteria were not responsible for the catalysis of acetate oxidation. In contrast, both groups of isolates were found to catalyse the electrochemical reduction of oxygen under experimental conditions that favoured adsorption of the microbial cells on the electrode surface.
Conclusions:  Members of the genera Enterobacter and Pseudomonas were found to be able to catalyse the electrochemical reduction of oxygen.
Significance and Impact of the Study:  This study has shown the unexpected efficiency of Enterobacter and Pseudomonas spp. in catalysing the reduction of oxygen, suggesting a possible involvement of these species in biocorrosion, or possible application of these strains in designing bio-cathode for microbial fuel cells.     

Electrochemistry of Escherichia coli JM109: direct electron transfer and antibiotic resistance

In this study, the cyclic voltammetry (CV) and square wave voltammetry (SWV) techniques were used to investigate the extracellular electron transfer from Escherichia coli JM109. It was demonstrated that the formal redox potential of direct electron transfer between electrode and an E. coli JM109 cell in aerobic buffer corresponds to -0.42 V vs. Ag/AgCl. Based on the electroactivity of bacterial cells, the electrochemical system for definition of sensitivity of microbiological material to antibiotics cefepime, ampicillin, amikacin, and erythromycin was proposed. The results obtained indicate that with electrochemical methods it is possible to provide screening of potential drugs for bacterial diseases. The electrochemical method allows estimating the degree of E. coli JM109 cells resistance to antibiotics within 2-5h using disposable screen-printed graphite electrodes.     

Electrochemistry and detection of some organic and biological molecules at conducting poly(3-methylthiophene) electrodes

Electrodes modified by the electrodeposition of poly(3-methylthiophene) were used as chemical sensors for some organic and biological molecules of industrial and medicinal interest. The electrochemical behaviors of ferri/ferrocyanide, catechol, ascorbic acid, hydroquinone, dopamine epinephrine, acetaminophen, p-aminophenol and NADH were examined by cyclic voltammetry. The results showed that the proposed modified surface catalyzes the oxidation of these compounds. Differential pulse and square wave techniques were used for the analysis of binary mixture of ascorbic acid with catechol, NADH, dopamine and p-aminophenol. Voltammetric peak resolution was also demonstrated for a ternary mixture of ascorbic acid, catechol and p-aminophenol. Polymer coated electrode was also used in an amperometric detector for flow injection analysis of most of the aforementioned compounds. The responses of the polymer electrode were 4-10 times larger as compared to those of platinum. The modified electrode displayed excellent response stability for successive injections and detection limits were 10 ppb for catechol, dopamine, epinephrine, NADH and p-aminophenol, 1 ppb for acetaminophen and 100 ppb for ascorbic acid. Voltammetric peak positions were affected by the nature of the electrolyte and its pH. Also, film thicknesses were shown to be a factor affecting both the current magnitudes and oxidation peak potential of NADH.     

Improved electrical wiring of microbes: anthraquinone-modified electrodes for biosensing of chlorinated hydrocarbons

The present study reports the development of a novel bioelectrochemical sensor for trichloroethene (TCE), a common subsurface contaminant, based on the measurement of the electrical current resulting from the microbially catalysed reduction of TCE at anthraquinone (AQ)-modified electrodes. Firstly, we describe the development and electrochemical characterisation of AQ-modified electrodes, prepared via spontaneous or electrochemical reduction of AQ diazonium derivatives. Finally, the proof-of-principle of the bioelectrochemical sensor for TCE was evaluated, using a TCE-dechlorinating microbial culture as the biosensing element. The response of the bioelectrochemical sensor was measured either as the peak current in cyclic voltammetry or the steady-state current in chronoamperometry; in both cases, it was found to be proportional to TCE concentrations in the range 0-100 μmol/L. On the other hand, the microorganisms in contact with the electrode surface caused severe fouling problems which drastically reduced the life-time of the sensor.     

Glucose oxidase-polypyrrole electrodes synthesized in <Emphasis Type="Italic">p</Emphasis>-toluenesulfonic acid and sodium <Emphasis Type="Italic">p</Emphasis>-toluenesulfonate

Amperometric glucose biosensors have been developed based on entrapment on platinum (Pt) electrode using cyclic voltammetry technique in glucose oxidase (GOD) and pyrrole containing p-toluenesulfonic acid (pTSA) or sodium p-toluenesulfonate (NapTS) as supporting electrolyte solutions. Both of electrolyte solutions were suitable media for the formation and deposition of polypyrrole-GOD (PPy-GOD) layers on Pt substrate. Pt/PPy-GOD electrodes brought about in different morphological properties as well as different electrochemical and biochemical response. The highest responses obtained in pTSA and NapTS electrolytes were observed at pH of 4.5 and 7.0 for Pt/PPy-GOD electrodes, respectively. While linearity was observed between 0.0–1.0 mM glucose substrate for both electrodes, I _max value of Pt/PPy-GOD_NapTS electrode was approximately twice as high as that of Pt/PPy-GOD_pTSA electrode as 25.4 and 14.2 μA, respectively. Five commercial drinks were tested with enzyme electrodes and compared with results obtained spectropho-tometrically using glucose kit. Results revealed that Pt/PPy-GOD_NapTS electrode exhibited better biosensor response.     

The first automated synthesis of ferrocene-labelled phosphorothioate DNA probe: a new potential tool for the fabrication of DNA microarrays

We report the synthesis and the characterisation of the first electroactive ferrocene-labelled oligonucleotide phosphorothioate (ODN-Fc-Ps) probe obtained by automated synthesis. The grafting of ODN-Fc-Ps probe on gold electrode resulted in the appearance of the ferrocene redox couple in cyclic voltammetry confirming the effectiveness of the ODN grafting. The electrochemical response of the modified electrode was analysed in aqueous media before and after hybridisation with ODN target. The hybridisation with ODN target induces a large conformational change in the surface-confined DNA structure monitored by cyclic voltammetry of the ferrocene marker which confirms the potential of ferrocene-labelled oligonucleotide phosphorothioate to develop electrochemical DNA chips.     

Digestion of restriction enzyme for the detection of single-base mismatch in DNA

DNA hybridization and enzymatic digestion for the detection of mutation was investigated on the gold nanoparticles-calf thymus DNA (AuNPs-ctDNA) modified glassy carbon electrode (GCE). The thiol modified probe oligonucleotides (SH-ssDNA) were assembled on the surface of AuNPs-ctDNA modified GCE. The electrochemical response of the electrode was measured by differential pulse voltammetry and cyclic voltammetry. Methylene blue (MB) was used as the electroactive indicator. AuNPs were then dispersed effectively on the GCE surface in the presence of ct-DNA. When hybridization occurred, a decrease in the signal of MB current was observed. The modified electrode was used for the detection of mutations during the enzymatic digestion reaction in DNA. During this reaction, an increase in the signal of MB current was observed. So, the modified SH-ssDNA had a higher electrochemical response on the AuNPs-ctDNA/GCE because of the strong affinity of MB for guanine residues in it. The electrochemical detection of restriction enzyme digestion can provide a simple and practical method for observing single-base mismatches that can help in distinguishing mismatch sequences of DNA from the complementary ones.     

Electrochemical evaluation of glucose oxidase immobilized by different methods

Glucose oxidase electrodes were constructed on a platinum screen using polyacrylamide gel, glutaraldehyde crosslinking, and glutaraldehyde crosslinking with +0.04 volts dc on the platinum screen as the methods of enzyme immobilization. The electrodes were evaluated in an electrochemical cell for the oxidation of glucose at the enzyme electrode and the reduction of oxygen at a platinum auxiliary electrode, using constant current voltametry or under external load operation. The method of immobilization affected the extrapolated opencircuit potential as well as the half-cell potential and the steady current under external load operation. The charged glutaraldehyde electrode gave the best current performance; however, the small output (microamps) indicated that major problems in electron transfer from an enzyme catalyst to an external circuit must be resolved before such electrodes can be used in practical application.     

Sensitive monitoring of riboflavin in commercial multivitamins using poly (chitosan)‐based nanocomposite

The rapid and sensitive determination of riboflavin (RF) is important for the treatment of seborrheic and glossitis dermatitis, sunlight sensitivity, mucosal, and skin disorders. In this work, an electrochemical sensor was developed by electrodes modification using poly (chitosan) to sensitive detection of RF in commercial multivitamin. Electrodeposition of chitosan on the surface of glass carbon electrode was performed using cyclic voltammetry technique in the range of ?1 to +1 V. The modified electrode surface morphology was characterized using a high‐resolution field emission scanning electron microscope. The modified electrode was used as an effective electrical interface for the detection of RF using cyclic, differential pulse, and square wave voltammetry techniques. Finally, the sensor was applied to determine RF in commercial multivitamins. In optimum conditions, the linear range for the standard sample of RF and commercial multivitamins 94 to 333μM and 24.6 to 176μM were obtained, respectively. Low limit of quantification (LLOQ) were obtained as 24.6μM.