60Co-γ射线辐照协同氢氧化钠预处理对油菜秸杆酶解产糖的影响

研究了辐照协同氢氧化钠预处理油菜秸秆对酶解产还原糖的影响。利用响应面法对氢氧化钠反应条件进行了优化,得出最优条件为氢氧化钠浓度为2．38％,反应温度为100℃,反应时间为0．5h。这一条件预期还原糖产量为524．93mg／g,通过实验验证,实际还原糖含量（528．51mg／g）能够很好地与预期相吻合。扫描电镜观察表明,辐照协同氢氧化钠预处理后秸秆表面积明显增大,出现很多蜂窝状孔洞结构,能够有效增大酶解可及表面积,从而提高酶解效率。     

Pretreatment of rapeseed straw by sodium hydroxide

Pretreatment method for rapeseed straw by sodium hydroxide was investigated for production of bioethanol and biobutanol. Various pretreatment parameters, including temperature, time, and sodium hydroxide concentration were optimized using a statistical method which is a central composite design of response surface methodology. In the case of sodium hydroxide pretreatment, optimal pretreatment conditions were found to be 7.9% sodium hydroxide concentration, 5.5 h of reaction time, and 68.4 °C of reaction temperature. The maximum glucose yield which can be recovered by enzymatic hydrolysis at the optimum conditions was 95.7% and the experimental result was 94.0 ± 4.8%. This experimental result was in agreement with the model prediction. An increase of surface area and pore size in pretreated rapeseed straw by sodium hydroxide pretreatment was observed by scanning electron microscope.     

Pretreatment of rapeseed straw by soaking in aqueous ammonia

Pretreatment of lignocellulosic biomass has gained attention for production of biofuels. In this study, pretreatment by soaking in aqueous ammonia was adopted for pretreatment of biomass for ethanol production. A central composite design of response surface methodology was used for optimization of the pretreatment condition of rapeseed straw, with respect to catalyst concentration, pretreatment time, and pretreatment temperature. The most optimal condition for pretreatment of rapeseed straw by soaking in aqueous ammonia was 19.8% of ammonia water, 14.2 h of pretreatment time, and a pretreatment temperature of 69.0 °C. Using these optimal factor values under experimental conditions, 60.7% of theoretical glucose was obtained, and this value was well within the range predicted by the model. SEM results showed that SAA pretreatment of rapeseed straw resulted in increased surface area and pore size, as well as enhanced enzymatic digestibility.     

Effect of organosolv pretreatment on mechanically pretreated biomass by use of concentrated ethanol as the solvent

In this study, we determined the effect of organosolv pretreatment on herbaceous biomasses corn stover and wheat straw, by using high-concentration ethanol as the solvent. A high-concentration of ethanol allows for the easy reuse and recycling of the solvent. First, we tested the effects of ethanol pretreatments at 60 and 99.5% (w/w) and found that highest solvent concentration resulted in low glucose digestibility. The maximum enzymatic glucose digestibility with 60% ethanol was 92.6% at 190°C for 120 min (using corn stover) and 86.9% at 190°C for 120 min (using wheat straw). In contrast, the digestion rates with 99.5% ethanol were 68.8 and 77.4% under the same conditions, respectively, indicating that there is a limit to the use of high-concentration ethanol as the solvent. To overcome this limitation, we applied a mechanical pretreatment step before the chemical pretreatment. Subsequently, glucose digestibility increased significantly to 93.1% with 99.5% ethanol as the solvent. Additionally the enzymatic digestibility of mechanically pretreated corn stover was higher than that of non-pretreated corn stover by about 40%. Taken together, these results confirm the efficacy of using high-concentration ethanol as a solvent for organosolv pretreatment when done in conjunction with mechanical pretreatment.     

Microscopic Structural Changes in Paddy Straw Pretreated with Trichoderma reesei MTCC 164 and Coriolus versicolor MTCC 138

The present study reports the pretreatment of paddy straw by Trichoderma reesei MTCC 164 and Coriolus versicolor MTCC 138 to observe the changes in chemical composition and its correlation with change of surface structure, morphology and porosity of paddy straw. Compared with untreated straw, cellulose decreased by 15.9 and 19.3 % in T. reesei MTCC 164 and C. versicolor MTCC 138 pretreated paddy straw respectively. Lignin content increased by 41.4 % in T. reesei pretreated paddy straw whereas decreased by 19.1 % in C. versicolor pretreated straw. The microscopic structural changes were examined by scanning electron microscopy under reasonable conditions. Results showed that digestibility of paddy straw are increased by treating paddy straw with both the cultures. Both surface area and pore size of treated straw were increased partially due to solubilization of silica components.     

Optimisation of the biological pretreatment of wheat straw with white-rot fungi for ethanol production

The biological pretreatment of lignocellulosic biomass for the production of bioethanol is an environmentally friendly alternative to the most frequently used process, steam explosion (SE). However, this pretreatment can still not be industrially implemented due to long incubation times. The main objective of this work was to test the viability of and optimise the biological pretreatment of lignocellulosic biomass, which uses ligninolytic fungi (Pleurotus eryngii and Irpex lacteus) in a solid-state fermentation of sterilised wheat straw complemented with a mild alkali treatment. In this study, the most important parameters of the mechanical and thermal substrate conditioning processes and the most important parameters of the fungal fermentation process were optimised to improve sugar recovery. The largest digestibilities were achieved with fermentation with I. lacteus under optimised conditions, under which cellulose and hemicellulose digestibility increased after 21 days of pretreatment from 16 to 100 % and 12 to 87 %, respectively. The maximum glucose yield (84 %) of cellulose available in raw material was obtained after only 14 days of pretreatment with an overall ethanol yield of 74 % of the theoretical value, which is similar to that reached with SE.     

High efficiency bioethanol production from barley straw using a continuous pretreatment reactor

We developed a new pretreatment process for producing high-efficiency bioethanol from a lignocellulosic biomass. Barley straw was pretreated with sodium hydroxide in a twin-screw extruder for continuous pretreatment. The biomass to ethanol ratio (BTER) for optimal pretreatment conditions was evaluated by response surface methodology. Simultaneous saccharification and fermentation (SSF) was conducted to investigate the BTER with 30 FPU/g cellulose of enzyme and 7% (v/v) yeast (Saccharomyces cerevisiae CHY 1011) using 10% (w/v) pretreated biomass under various pretreatment conditions. The maximum BTER was 73.00% under optimal pretreatment conditions (86.61 °C, 0.58 M, and 84.79 mL/min for temperature, sodium hydroxide concentration, and solution flow rate, respectively) and the experimental BTER was 70.01 ± 0.59%. SSF was performed to investigate the optimal enzyme and biomass dosage. As a result, maximum ethanol concentration and ethanol yield were 46.00 g/L and 77.36% at a loading pretreated biomass of 20% with 30 FPU/g cellulose of the enzyme dosage for barley straw to bioethanol. These results are a significant contribution to the production of bioethanol from barley straw.     

Effectiveness of microbial pretreatment by Ceriporiopsis subvermispora on different biomass feedstocks

Different types of feedstocks, including corn stover, wheat straw, soybean straw, switchgrass, and hardwood, were tested to evaluate the effectiveness of fungal pretreatment by Ceriporiopsis subvermispora. After 18-d pretreatment, corn stover, switchgrass, and hardwood were effectively delignified by the fungus through manganese peroxidase and laccase. Correspondingly, glucose yields during enzymatic hydrolysis reached 56.50%, 37.15%, and 24.21%, respectively, which were a 2 to 3-fold increase over those of the raw materials. A further 10-30% increase in glucose yields was observed when pretreatment time extended to 35 d. In contrast, cellulose digestibility of wheat straw and soybean straw was not significantly improved by fungal pretreatment. When external carbon sources and enzyme inducers were added during fungal pretreatment of wheat straw and soybean straw, only glucose and malt extract addition improved cellulose digestibility of wheat straw. The cellulose digestibility of soybean straw was not improved.     

Ammonia and sodium hydroxide treatment of wheat straw in diets for fattening steers

The effects of treating Neepawa wheat straw with anhydrous ammonia (35 kg t^?1), sodium hydroxide (50 kg t^?1) and pelleting were evaluated in two experiments. The diets consisted of 51% rolled barley, 40% straw, 4% rapeseed meal, 2% tallow, plus minerals and a vitamin supplement. Straw was treated as follows: (1) shredded into 2.0-cm lengths; (2) shredded into 0.64-cm lengths and pelleted; (3) ammoniated and shredded; (4) ammoniated and pelleted; (5) sodium hydroxide and pelleted; (6) ammoniated, sodium hydroxide and pelleted.Apparent digestibility was measured with six steers per treatment. Pelleting had no effect on organic matter (OM) digestibility, but decreased neutral detergent fibre (NDF) and cellulose digestion. Respective increases for OM and NDF digestibility following chemical treatment of the straw were as follows: ammoniation — 15 and 17%; sodium hydroxide — 4 and 13%.The six diets were given to 144 Hereford steers (240 kg) for 92 days in the second experiment. Feed consumption ranged from 8.51 to 10.39 kg day^?1 for diets 1 and 4, and body weight gains ranged from 0.83 to 1.26 kg day^?1 for diets 1 and 6, respectively. Respective increases for intake, gain and feed efficiency compared to untreated shredded straw were as follows: pelleting — 11, 34 and 17%; ammoniation — 12, 36 and 17%. Sodium hydroxide treatment prior to pelleting improved intake, gain and feed efficiency by 5, 10 and 5%, respectively. There was no evidence of additive effects between ammoniation and either pelleting or alkali treatment, though treatment with sodium hydroxide prior to pelleting did result in the highest gains and feed efficiency.     

Monosaccharide yields and lignin removal from wheat straw in response to catalyst type and pH during mild thermal pretreatment

The influence of various low temperature (140 °C) pretreatments, using different acid and alkaline catalysts and different pH values, was studied for enzymatic hydrolysis of wheat straw. The pretreated wheat straw was treated by a standard blend of Celluclast 1.5L and Novozym 188. While pretreatment at pH 1 gave the highest yield of saccharides in the liquid fraction, the solid fraction was more susceptible to enzymatic attack when pretreated at pH 13. The highest yields were obtained after pretreatment with hydrochloric acid at pH 1, and with sodium hydroxide at pH 13 when enzymatic hydrolysis was employed. A two-step pretreatment strategy at pH 1 (hydrochloric acid) and subsequently at pH 13 (sodium hydroxide) released 69% and 95% of the theoretical maximal amounts of glucose and xylose, respectively. Furthermore, this two-step pretreatment removed 68% of the lignin from the straw with only minor losses of monosaccharides and production of only low amounts of inhibitors. Type of catalyst and pH indeed influenced the monosaccharide yields and lignin removal from wheat straw, and need more attention in the choice of pretreatment strategy.     

Front-end recovery of protein from lignocellulosic biomass and its effects on chemical pretreatment and enzymatic saccharification

Front-end protein recovery from biomass at different maturities, and its effects on chemical pretreatment and enzyme hydrolysis of partially deproteinized fiber were investigated. The protein recovery from alfalfa and switchgrass biomass using sodium dodecyl sulfate and potassium hydroxide treatments was ~50–65 % of initial biomass protein. When hot water was used as extraction media, the protein recovery was 52.9 and 43.7 % of total protein in switchgrass and alfalfa, respectively. For any treatment, relative protein recovery was higher from switchgrass than from alfalfa. Only approximately half the total protein was recovered from relatively mature (early fall) biomass compared with midsummer harvested biomass. When protein was recovered partially using sodium dodecyl sulfate or potassium hydroxide, and leftover fiber pretreated, aqueous ammonia pretreatment removed 58.5–60.1 % of lignin and retained more cellulose in the fiber compared with acid pretreatment (nearly no lignin removal). Protein removal was helpful in the enzyme digestibility of fibers. Delignification of ammonia pretreated partially deproteinized alfalfa fiber was in the range of 34.4–45 %, while dilute sulfuric acid did not remove lignin effectively. Overall, the higher delignification and enzyme digestibilities were observed in aqueous ammonia pretreated partially deproteinized alfalfa fibers regardless of biomass type.     

The optimized CO2-added ammonia explosion pretreatment for bioethanol production from rice straw

A CO₂-added ammonia explosion pretreatment was performed for bioethanol production from rice straw. The pretreatment conditions, such as ammonia concentration, CO₂ loading level, residence time, and temperature were optimized using response surface methodology. The response for optimization was defined as the glucose conversion rate. The optimized pretreatment conditions resulting in maximal glucose yield (93.6 %) were determined as 14.3 % of ammonia concentration, 2.2 MPa of CO₂ loading level, 165.1 °C of temperature, and 69.8 min of residence time. Scanning electron microscopy analysis showed that pretreatment of rice straw strongly increased the surface area and pore size, thus increasing enzymatic accessibility for enzymatic saccharification. Finally, an ethanol yield of 97 % was achieved via simultaneous saccharification and fermentation. Thus, the present study suggests that CO₂-added ammonia pretreatment is an appropriate process for bioethanol production from rice straw.     

Pretreatment of wheat straw for fermentation to methane

The effects of pretreating wheat straw with gamma-ray irradiation, ammonium hydroxide, and sodium hydroxide on methane yield, fermentation rate constant, and loss of feedstock constituents were evaluated using laboratory-scale batch fermentors. Results showed that methane yield increased as pretreatment alkali concentration increased, with the highest yield being 37% over untreated straw for the pretreatment consisting of sodium hydroxide dosage of 34 g OH(-)/kg volatile solids, at 90 degrees C for 1 h. Gamma-ray irradiation had no significant effect on methane yield. Alkaline pretreatment temperatures above 100 degrees C caused a decrease in methane yield. After more than 100 days of fermentation, all of the hemi-cellulose and more than 80% of the cellulose were degraded. The loss in cellulose and hemicellulose accounted for 100% of the volatile solids lost. No consistent effect of pretreatments on batch fermentation rates was noted. Semicontinuous fermentations of straw-manure mixtures confirmed the relative effectiveness of sodium and ammonium-hydroxide pretreatments.     

Understanding the Physicochemical Characteristics and the Improved Enzymatic Saccharification of Corn Stover Pretreated with Aqueous and Gaseous Ammonia

Physicochemical characteristics of corn stover pretreated by soaking in aqueous ammonia (SAA) and low-moisture anhydrous ammonia (LMAA) were compared and investigated. The glucan digestibility of the treated biomass reached 90 % (SAA) and 84 % (LMAA). The LMAA pretreatment enhanced the digestibility by cleaving cross-linkages between cell wall components, whereas the SAA pretreatment additionally improved the digestibility by efficiently removing a major portion of the lignin under mild reaction conditions without significant loss of carbohydrates. Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR), and gel permeation chromatography (GPC) revealed the structural and chemical transformations of lignin during the pretreatments. Both pretreatments effectively cleaved ferulate cell wall cross-linking that is associated with the recalcitrance of grass lignocellulosics toward enzymatic saccharification. Extracted lignin from SAA pretreatment was extensively depolymerized but retained “native” character, as evidenced by the retention of β-ether linkages.     

Laccase-Mediator Pretreatment of Wheat Straw Degrades Lignin and Improves Saccharification

Agricultural by-products such as wheat straw are attractive feedstocks for the production of second-generation bioethanol due to their high abundance. However, the presence of lignin in these lignocellulosic materials hinders the enzymatic hydrolysis of cellulose. The purposes of this work are to study the ability of a laccase-mediator system to remove lignin improving saccharification, as a pretreatment of wheat straw, and to analyze the chemical modifications produced in the remaining lignin moiety. Up to 48 % lignin removal from ground wheat straw was attained by pretreatment with Pycnoporus cinnabarinus laccase and 1-hydroxybenzotriazole (HBT) as mediator, followed by alkaline peroxide extraction. The lignin removal directly correlated with increases (～60 %) in glucose yields after enzymatic saccharification. The pretreatment using laccase alone (without mediator) removed up to 18 % of lignin from wheat straw. Substantial lignin removal (37 %) was also produced when the enzyme-mediator pretreatment was not combined with the alkaline peroxide extraction. Two-dimensional nuclear magnetic resonance (2D NMR) analysis of the whole pretreated wheat straw material swollen in dimethylsulfoxide-d ₆ revealed modifications of the lignin polymer, including the lower number of aliphatic side chains involved in main β-O-4′ and β-5′ inter-unit linkages per aromatic lignin unit. Simultaneously, the removal of p-hydroxyphenyl, guaiacyl, and syringyl lignin units and of p-coumaric and ferulic acids, as well as a moderate decrease of tricin units, was observed without a substantial change in the wood polysaccharide signals. Especially noteworthy was the formation of Cα-oxidized lignin units during the enzymatic treatment.     

Improved enzymatic hydrolysis yield of rice straw using electron beam irradiation pretreatment

Rice straw was irradiated using an electron beam at currents and then hydrolyzed with cellulase and beta-glucosidase to produce glucose. The pretreatment by electron beam irradiation (EBI) was found to significantly increase the enzyme digestibility of rice straw. Specifically, when rice straw that was pretreated by EBI at 80 kGy at 0.12 mA and 1 MeV was hydrolyzed with 60 FPU of cellulase and 30 CBU of beta-glucosidase, the glucose yield after 132 h of hydrolysis was 52.1% of theoretical maximum. This value was significantly higher than the 22.6% that was obtained when untreated rice straw was used. In addition, SEM analysis of pretreated rice straw revealed that EBI caused apparent damage to the surface of the rice straw. Furthermore, EBI pretreatment was found to increase the crystalline portion of the rice straw. Finally, the crystallinity and enzyme digestibility were found to be strongly correlated between rice straw samples that were pretreated by EBI under different conditions.     

Screening of ecologically diverse fungi for their potential to pretreat lignocellulosic bioenergy feedstock

A widespread and hitherto by far underexploited potential among ecologically diverse fungi to pretreat wheat straw and digestate from maize silage in the future perspective of using such lignocellulosic feedstock for fermentative bioenergy production was inferred from a screening of nine freshwater ascomycetes, 76 isolates from constructed wetlands, nine peatland isolates and ten basidiomycetes. Wheat straw pretreatment was most efficient with three ascomycetes belonging to the genera Acephala (peatland isolate) and Stachybotrys (constructed wetland isolates) and two white-rot fungi (Hypholoma fasciculare and Stropharia rugosoannulata) as it increased the amounts of water-extractable total sugars by more than 50 % and sometimes up to 150 % above the untreated control. The ascomycetes delignified wheat straw at rates (lignin losses between about 31 and 40 % of the initial content) coming close to those observed with white-rot fungi (about 40 to 57 % lignin removal). Overall, fungal delignification was indicated as a major process facilitating the digestibility of wheat straw. Digestate was generally more resistant to fungal decomposition than wheat straw. Nevertheless, certain ascomycetes delignified this substrate to extents sometimes even exceeding delignification by basidiomycetes. Total sugar amounts of about 20 to 60 % above the control value were obtained with the most efficient fungi (one ascomycete of the genus Phoma, the unspecific wood-rot basidiomycete Agrocybe aegerita and one unidentified constructed wetland isolate). This was accompanied by lignin losses of about 47 to 56 % of the initial content. Overall, digestate delignification was implied to be less decisive for high yields of fermentable sugars than wheat straw delignification.     

Efficacy of acidic pretreatment for the saccharification and fermentation of alginate from brown macroalgae

This study was performed to evaluate the effectiveness of acidic pretreatment in increasing the enzymatic digestibility of alginate from brown macroalgae. Pretreatment with 1 % (w/v) sulfuric acid at 120 °C for 30 min produced oligosaccharides, mannuronic acid, and guluronic acid. Enzymatic saccharification of pretreated alginate by alginate lyases produced 52.2 % of the theoretical maximal sugar yield, which was only 7.5 % higher than the sugar yield obtained with unpretreated alginate. Mass spectrometric analyses of products of the two reactions revealed that acidic pretreatment and enzymatic saccharification produced saturated monomers (i.e., mannuronic and guluronic acid) with saturated oligosaccharides and unsaturated monomers (i.e., 4-deoxy-l-erythro-5-hexoseulose uronic acid; DEH), respectively. While DEH is further metabolized by microorganisms, mannuronic acid and guluronic acid are not metabolizable. Because of the poor efficacy in increasing enzymatic digestibility and owing to the formation of non-fermentable saturated monomers, acidic pretreatment cannot be recommended for enzymatic saccharification and fermentation of alginate.     

Comparative evaluation of acid and alkaline sulfite pretreatments for enzymatic saccharification of bagasses from three different sugarcane hybrids

Sugarcane bagasses from three experimental sugarcane hybrids and a mill‐reference sample were used to compare the efficiency and mode of action of acid and alkaline sulfite pretreatment processes. Varied chemical loads and reaction temperatures were used to prepare samples with distinguished characteristics regarding xylan and lignin removals, as well as sulfonation levels of residual lignins. The pretreatment with low sulfite loads (5%) under acidic conditions (pH 2) provided maximum glucose yield of 70% during enzymatic hydrolysis with cellulases (10 FPU/g) and β‐glucosidases (20 UI/g bagasse). In this case, glucan enzymatic conversion from pretreated materials was mostly associated with extensive xylan removal (70–100%) and partial delignification occurred during the pretreatment. The use of low sulfite loads under acidic conditions required pretreatment temperatures of 160°C. In contrast, at a lower pretreatment temperature (120°C), alkaline sulfite process achieved similar glucan digestibility, but required a higher sulfite load (7.5%). Residual xylans from acid pretreated materials were almost completely hydrolysed by commercial enzymes, contrasting with relatively lower xylan to xylose conversions observed in alkaline pretreated samples. Efficient xylan removal during acid sulfite pretreatment and during enzymatic digestion can be useful to enhance glucan accessibility and digestibility by cellulases. Alkaline sulfite process also provided substrates with high glucan digestibility, mainly associated with delignification and sulfonation of residual lignins. The results demonstrate that temperature, pH, and sulfite can be combined for reducing lignocellulose recalcitrance and achieve similar glucan conversion rates in the alkaline and acid sulfite pretreated bagasses. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:944–951, 2018     

Lignocellulose conversion for biofuel: a new pretreatment greatly improves downstream biocatalytic hydrolysis of various lignocellulosic materials

Background

Lignocellulosic biomass is an attractive renewable resource for future liquid transport fuel. Efficient and cost-effective production of bioethanol from lignocellulosic biomass depends on the development of a suitable pretreatment system. The aim of this study is to investigate a new pretreatment method that is highly efficient and effective for downstream biocatalytic hydrolysis of various lignocellulosic biomass materials, which can accelerate bioethanol commercialization.

Results

The optimal conditions for the hydrogen peroxide–acetic acid (HPAC) pretreatment were 80 °C, 2 h, and an equal volume mixture of H₂O₂ and CH₃COOH. Compared to organo-solvent pretreatment under the same conditions, the HPAC pretreatment was more effective at increasing enzymatic digestibility. After HPAC treatment, the composition of the recovered solid was 74.0 % cellulose, 20.0 % hemicelluloses, and 0.9 % lignin. Notably, 97.2 % of the lignin was removed with HPAC pretreatment. Fermentation of the hydrolyzates by S. cerevisiae resulted in 412 mL ethanol kg^?1 of biomass after 24 h, which was equivalent to 85.0 % of the maximum theoretical yield (based on the amount of glucose in the raw material).

Conclusion

The newly developed HPAC pretreatment was highly effective for removing lignin from lignocellulosic cell walls, resulting in enhanced enzymatic accessibility of the substrate and more efficient cellulose hydrolysis. This pretreatment produced less amounts of fermentative inhibitory compounds. In addition, HPAC pretreatment enables year-round operations, maximizing utilization of lignocellulosic biomass from various plant sources.