Optimization of free ammonia concentration for nitrite accumulation in shortcut biological nitrogen removal process

A shortcut biological nitrogen removal (SBNR) utilizes the concept of a direct conversion of ammonium to nitrite and then to nitrogen gas. A successful SBNR requires accumulation of nitrite in the system and inhibition of the activity of nitrite oxidizers. A high concentration of free ammonia (FA) inhibits nitrite oxidizers, but unfortunately decreases the ammonium removal rate as well. Therefore, the optimal range of FA concentration is necessary not only to stabilize nitrite accumulation but also to achieve maximum ammonium removal. In order to derive such optimal FA concentrations, the specific substrate utilization rates of ammonium and nitrite oxidizers were measured. The optimal FA concentration range appeared to be 5–10 mg/L for the adapted sludge. The simulated results from the modified inhibition model expressed by FA and ammonium/nitrite concentrations were shown very similar to the experimental results.     

Biological treatment of low-salinity shrimp aquaculture wastewater using sequencing batch reactor

In order to improve the water quality in shrimp aquaculture operated under low-salinity conditions, a sequencing batch reactor (SBR) was tested for treatment of the wastewater. This water from the backwash of a single-bead filter from the Waddell Mariculture Center, South Carolina, contained high concentrations of carbon and nitrogen and was successfully treated using the SBR. By operating the reactor sequentially in aerobic, anoxic and aerobic modes, nitrification and denitrification were achieved, as well as removal of carbon. Specifically, the initial chemical oxygen demand (COD) concentration of 1201 mg l⁻¹ was reduced to 32 mg l⁻¹ within 8 days of reactor operation. Ammonia in the sludge was nitrified within 3 days. The denitrification of nitrate was achieved by the anoxic process and total removal of nitrate was observed.     

Dynamic simulation of a WWTP operated at low dissolved oxygen condition by integrating activated sludge model and a floc model

While an aeration tank in an activated sludge process is often operated with high dissolved oxygen (DO) concentration to ensure organic degradation and nitrification, it may be operated at low DO concentration to reduce energy consumption and achieve desired denitrification. The ASM1 (Activated Sludge Model No. 1) can be used to describe the activated sludge process if the nitrification and denitrification occur either during different phases or in different tanks, but it may encounter problems in simulating the denitrification phenomenon caused by low DO concentration in the aeration tank. In the present work, we developed a model integrating the ASM1 kinetics and a biofloc model to account for the actual anoxic and aerobic rates. Oxygen was assumed the only substrate of both bio-kinetically and flux limiting in the flocs and its dispersion coefficient was estimated as 1.2 × 10⁻⁴ m² day⁻¹ by using a set of measured effluent qualities of a full-scale wastewater treatment plant (WWTP) operating at low DO concentration (∼0.80 mg L⁻¹) for 60 days. Simulation studies predicted the optimal DO level of 0.36 mg L⁻¹ which would lead to minimum total nitrogen of 15.7 mg N L⁻¹ and also showed the insignificance of the addition of carbon source for nitrogen removal for the operation under study. The developed model may be helpful for process engineers to predict the plant behaviors under various configurations or operating strategies.     

Operation of partial nitrification to nitrite of landfill leachate and its performance with respect to different oxygen conditions

The coupled system of partial nitrification and anaerobic ammonium oxidation (Anammox) is efficient in nitrogen removal from wastewater. In this study, the effect of different oxygen concentrations on partial nitrification performance with a sequencing batch reactor (SBR) was investigated. Results indicate that, partial nitrification of landfill leachate could be successfully achieved under the 1.0–2.0 mg L⁻¹ dissolved oxygen (DO) condition after 118 d long-term operation, and that the effluent is suitable for an Anammox reactor. Further decreasing or increasing the DO concentration, however, would lead to a decay of nitrification performance. Additionally, the MLSS concentration in the reactor increased with increasing DO concentration. Respirometric assays suggest that low DO conditions (<2 mg L⁻¹) favor the ammonia-oxidizing bacteria (AOB) and significantly inhibit nitrite oxidizing bacteria (NOB) and aerobic heterotrophic bacteria (AHB); whereas high DO conditions (>3 mg L⁻¹) allow AHB to dominate and significantly inhibit AOB. Therefore, the optimal condition for partial nitrification of landfill leachate is 1.0–2.0 mg L⁻¹ DO concentration.     

Factors Affecting Nitrous Oxide Production: A Comparison of Biological Nitrogen Removal Processes with Partial and Complete Nitrification

Nitrous oxide (N₂O) emission from biological nitrogen removal (BNR) processes has recently received more research attention. In this study, two lab-scale BNR systems were used to investigate the effects of various operating parameters including the carbon to nitrogen (C/N) ratio, ammonia loading, and the hydraulic retention time on N₂O production. The first system was operated in a conventional BNR mode known as the Ludzack–Ettinger (LE) process, consisting of complete denitrification and nitrification reactors, while the second one was operated in a shortcut BNR (SBNR) mode employing partial nitrification and shortcut denitrification, which requires less oxygen and carbon sources. As the C/N ratio was decreased, a significant increase in N₂O production was observed only in the anoxic reactor of the LE process, indicating that N₂O was released as an intermediate of the denitrification reaction under the carbon-limited condition. However, the SBNR process did not produce significant N₂O even at the lowest C/N ratio of 0.5. When the SBNR process was subjected to increasing concentrations of ammonia, N₂O production from the aerobic reactor was rapidly increased. Furthermore, the increasing production of N₂O was observed mostly in the aerobic reactor of the SBNR process with a decline in hydraulic retention time. These experimental findings indicated that the increase in N₂O production was closely related to the accumulation of free ammonia, which was caused by an abrupt increase of the ammonium loading. Consequently, the partial nitrification was more susceptible to shock loading conditions, resulting in a high production of N₂O, although the SBNR process was more efficient with respect to nitrogen removals as well as carbon and oxygen requirements.     

Multi‐species nitrifying biofilm model (MSNBM) including free ammonia and free nitrous acid inhibition and oxygen limitation

A multi‐species nitrifying biofilm model (MSNBM) is developed to describe nitrite accumulation by simultaneous free ammonia (FA) and free nitrous acid (FNA) inhibition, direct pH inhibition, and oxygen limitation in a biofilm. The MSNBM addresses the spatial gradient of pH with biofilm depth and how it induces changes of FA and FNA speciation and inhibition. Simulations using the MSNBM in a completely mixed biofilm reactor show that influent total ammonia nitrogen (TAN) concentration, bulk dissolved oxygen (DO) concentration, and buffer concentration exert significant control on the suppression of nitrite‐oxidizing bacteria (NOB) and shortcut biological nitrogen removal (SBNR), but the pH in the bulk liquid has a weaker influence. Ammonium oxidation increases the nitrite concentration and decreases the pH, which together can increase FNA inhibition of NOB in the biofilm. Thus, a low buffer concentration can accentuate SBNR. DO and influent TAN concentrations are efficient means to enhance DO limitation, which affects NOB more than ammonia‐oxidizing bacteria (AOB) inside the biofilm. With high influent TAN concentration, FA inhibition is dominant at an early phase, but finally DO limitation becomes more important as TAN degradation and biofilm growth proceed. MSNBM results indicate that oxygen depletion and FNA inhibition throughout the biofilm continuously suppress the growth of NOB, which helps achieve SBNR with a lower TAN concentration than in systems without concentration gradients. Biotechnol. Bioeng. 2010;105: 1115–1130. © 2009 Wiley Periodicals, Inc.     

Effect of oxic and anoxic conditions on nitrous oxide emissions from nitrification and denitrification processes

A lab-scale sequencing batch reactor fed with real municipal wastewater was used to study nitrous oxide (N(2)O) emissions from simulated wastewater treatment processes. The experiments were performed under four different controlled conditions as follows: (1) fully aerobic, (2) anoxic-aerobic with high dissolved oxygen (DO) concentration, (3) anoxic-aerobic with low DO concentration, and 4) intermittent aeration. The results indicated that N(2)O production can occur from both incomplete nitrification and incomplete denitrification. N(2)O production from denitrification was observed in both aerobic and anoxic phases. However, N(2)O production from aerobic conditions occurred only when both low DO concentrations and high nitrite concentration existed simultaneously. The magnitude of N(2) O produced via anoxic denitrification was lower than via oxic denitrification and required the presence of nitrite. Changes in DO, ammonium, and nitrite concentrations influenced the magnitude of N(2)O production through denitrification. The results also suggested that N(2)O can be produced from incomplete denitrification and then released to the atmosphere during aeration phase due to air stripping. Therefore, biological nitrogen removal systems should be optimized to promote complete nitrification and denitrification to minimize N(2)O emissions.     

Nitrite reduction by a mixed culture under conditions relevant to shortcut biological nitrogen removal

Dissimilative reduction of nitrite by nitrite-acclimated cellswas investigated in a batch reactor under various environmental conditions that can beencountered in shortcut biological nitrogen removal (SBNR: ammonia to nitrite andnitrite to nitrogen gas). The maximum specific nitrite reduction rate was as much as 4.3 times faster than the rate of nitrate reduction when individually tested, but the reaction was inhibited in the presence of nitrate when the initial nitrate concentration was greater than approximately 25 mg-N/l or the initialNO ₃ ^- N/NO ₂ ^- N ratio was larger than 0.5. Nitrite reduction was also inhibited by nitrite itself when theconcentration was higher than that to which the cells had been acclimated. Therefore, it was desirable to avoid excessively high nitrite and nitrate concentrations in a denitrification reactor. Nitrite reduction, however, was not affected by an alkaline pH (in the range of 7–9) or a high concentration of FA (in the range of 16–39 mg/l), which can be common in SBNR processes. The chemical oxygen demand (COD) requirement for nitrite reduction was approximately 22–38% lower than that for nitrate reduction, demonstrating that the SBNR process can be economical. The specific consumption,measured as the ratio of COD consumed to nitrogen removed, was affected by the availability of COD and the physiological state of the cells. The ratio increased when the cells grew rapidly and were storing carbon and electrons.     

Modeling kinetics of ammonium oxidation and nitrite oxidation under simultaneous inhibition by free ammonia and free nitrous acid

Inhibition of ammonium oxidation and nitrite oxidation by free ammonia (FA) and free nitrous acid (FNA) was studied using three different sludges. An uncompetitive inhibition model fit the experimental data well when the reactions were under FA inhibition, whereas a noncompetitive model fit well under FNA inhibition. The estimates of the inhibition constant (K_I) of nitrite oxidation were 46 μM for FA and 1.7–6.8 μM for FNA, each of which was significantly smaller than that of ammonium oxidation, which were 290–1600 μM for FA and 12 μM for FNA. The much smaller values of K_I for nitrite oxidation reflected the susceptibility of that reaction to inhibition by FA and FNA, which could lead to accumulation of nitrite during nitrification. A kinetic model for simultaneous inhibition by FA and FNA was derived. The model predicted that nitrite oxidation should be affected more seriously than ammonium oxidation by the simultaneous inhibition, which would accelerate the accumulation of nitrite in a strong nitrogenous wastewater treatment. It also indicated that a complete removal of ammonia could be achieved with high accumulation of nitrite in a sequencing batch reactor, which is impossible in a continuous-flow reactor.     

Identification of novel small molecule enhancers of protein production by cultured mammalian cells

Shortcut nitrogen removal, that is, removal via formation and reduction of nitrite rather than nitrate, has been observed in membrane-aerated biofilms (MABs), but the extent, the controlling factors, and the kinetics of nitrite formation in MABs are poorly understood. We used a special MAB reactor to systematically study the effects of the dissolved oxygen (DO) concentration at the membrane surface, which is the biofilm base, on nitrification rates, extent of shortcut nitrification, and microbial community structure. The focus was on anoxic bulk liquids, which is typical in MAB used for total nitrogen (TN) removal, although aerobic bulk liquids were also studied. Nitrifying MABs were grown on a hollow-fiber membrane exposed to 3 mg N/L ammonium. The MAB intra-membrane air pressure was varied to achieve different DO concentrations at the biofilm base, and the bulk liquid was anoxic or with 2 g m(-3) DO. With 2.2 and 3.5 g m(-3) DO at the biofilm base, and with an anoxic bulk-liquid, the ammonium fluxes were 0.75 and 1.0 g N m(-2) day(-1), respectively, and nitrite was the main oxidized nitrogen product. However, with membrane DO of 5.5 g m(-3), and either zero or 2 g m(-3) DO in the bulk, the ammonium flux was around 1.3 g N m(-2) day(-1), and nitrate flux increased significantly. For all experiments, the cell density of ammonium oxidizing bacteria (AOB) was relatively uniform throughout the biofilm, but the density of nitrite oxidizing bacteria (NOB) decreased with decreasing biofilm DO. Among NOB, Nitrobacter spp. were dominant in biofilm regions with 2 g m(-3) DO or greater, while Nitrospira spp. were dominant in regions with less than 2 g m(-3) DO. A biofilm model, including AOB, Nitrobacter spp., and Nitrospira spp., was developed and calibrated with the experimental results. The model predicted the greatest extent of nitrite formation (95%) and the lowest ammonium oxidation flux (0.91 g N m(-2) day(-1)) when the membrane DO was 2 g m(-3) and the bulk liquid was anoxic. Conversely, the model predicted the lowest extent of nitrite formation (40%) and the highest ammonium oxidation flux (1.5 g N m(-2) day(-1)) when the membrane-DO and bulk-DO were 8 g m(-3) and 2 g m(-3), respectively. The estimated kinetic parameters for Nitrospira spp., revealed a high affinity for nitrite and oxygen. This explains the dominance of Nitrospira spp. over Nitrobacter spp. in regions with low nitrite and oxygen concentrations. Our results suggest that shortcut nitrification can effectively be controlled by manipulating the DO at the membrane surface. A tradeoff is made between increased nitrite accumulation at lower DO, and higher nitrification rates at higher DO.     

Short-cut nitrification of domestic wastewater in a pilot-scale A/O nitrogen removal plant

The feasibility of nitrite accumulation in a pilot-scale A/O (anoxic/oxic) nitrogen removal plant treating domestic wastewater was investigated at various dissolved oxygen (DO) concentrations and pH levels. The results showed that the pH was not a useful operational parameter to realize nitrite accumulation. Significant nitrite accumulation was observed at the low DO concentration range of 0.3–0.8 mg/l and the maximum nitrite accumulation ratio of about 90% occurred at a DO concentration of 0.6 mg/l. This suggests a reduction of 22% in the oxygen consumption, and therefore a considerable saving in aeration. However, the nitrite accumulation was destroyed at the high DO concentration and the resumption was very slow. In addition, the average ammonia removal efficiency reached as high as 93% at the low DO level. Moreover, experimental results indicated that nitrogen could be removed by simultaneous nitrification and denitrification (SND) via nitrite in the aerobic zones at the low DO concentration, with the efficiency of 6–12%.     

Heterotrophs grown on the soluble microbial products (SMP) released by autotrophs are responsible for the nitrogen loss in nitrifying granular sludge

In this work, nitrogen loss in the nitrite oxidation step of the nitrification process in an aerobic‐granule‐based reactor was characterized with both experimental and modeling approaches. Experimental results showed that soluble microbial products (SMP) were released from the nitrite‐oxidizing granules and were utilized as a carbon source by the heterotrophs for denitrification. This was verified by the fluorescence in situ hybridization (FISH) analysis. Microelectrode tests showed that oxygen diffusion limitation did result in an anoxic micro‐zone in the granules and allowed sequential utilization of nitrate as an electron acceptor for heterotrophic denitrification with SMP as a carbon source. To further elucidate the nitrogen loss mechanisms, a mathematic model was formulated to describe the growth of nitrite oxidizers, the formation and consumption of SMP, the anoxic heterotrophic growth on SMP and nitrate, as well as the oxygen transfer and the substrate diffusion in the granules. The results clearly indicate that the heterotrophs grown on the SMP released by the autotrophs are responsible for the nitrogen loss in the nitrifying granules, and give us a better understanding of the aerobic granules for nitrogen removal. Biotechnol. Bioeng. 2011;108: 2844–2852. © 2011 Wiley Periodicals, Inc.     

Impact of carbon to nitrogen ratio on nutrient removal in a liquid–solid circulating fluidized bed bioreactor (LSCFB)

The performance of a liquid–solid circulating fluidized bed bioreactor (LSCFB) with anoxic and aerobic beds and lava rock as a biofilm carrier media was used to investigate the impact of the COD/N ratio on the process performance, with particular focus on total nitrogen removal. Three different COD/N ratios of 10:1, 6:1 and 4:1 were tested at an empty bed contact time of 0.82 h. More than 90% of the influent organic matter was removed throughout the study with 58% removal in the anoxic column in Phase III. Total nitrogen removal efficiencies in Phases I–III were 91%, 82% and 71% and simultaneous nitrification–denitrification (SND) occurred in the aerobic downer. The LSCFB demonstrated tertiary effluent quality at COD/N ratio of 10:1 and 6:1 with soluble biochemical oxygen demand (SBOD) <10 mg l^?1 and total nitrogen (TN) <10 mg l^?1.     

Air-lift internal loop biofilm reactor for realized simultaneous nitrification and denitrification

Simultaneous nitrification and denitrification (SND) was realized by means of a novel air-lift internal loop biofilm reactor, in which aeration was set in middle of the reactor. During operation, the aeration was adjusted to get appropriate dissolve oxygen (DO) in bulk solution and let aerobic and anoxic zone coexist in one reactor. When aeration was at 0.6 and 0.2 L/min, corresponding to DO of 5.8 and 2.5 mg/L in bulk solution, ammonia nitrogen removal percentage reached about 80 and 90 %, but total nitrogen removal percentage was lower than 25 %. While the aeration was reduced to 0.1 L/min, aerobic and anoxic zones existed simultaneously in one reactor to get 75 % of ammonia nitrogen and 50 % of total nitrogen removal percentage. Biofilms were, respectively, taken from aerobic and anoxic zone to verify their function of nitrification and denitrification in two flasks, in which ammonia nitrogen was transferred into nitrate completely by aerobic biofilm, and nitrate was removed more than 80 % by anoxic biofilm. Microelectrode was used to measure the DO distribution inside biofilms in anoxic zone corresponding to different aerations. When aeration was at 0.6 and 0.2 L/min, DO inside biofilm was more than 1.5 mg/L, but the DO inside biofilm decreased to anoxic status with depth of biofilm increasing corresponding to aeration of 0.1 L/min. The experimental results indicated that SND could be realized because of simultaneous existence of aerobic and anoxic biofilms in one reactor.     

A unified model of ammonium oxidation rate at various initial ammonium strength and active ammonium oxidizer concentrations

This paper attempts to provide insight into the biological ammonium oxidation process applied to high-strength ammonium wastewater treatment. The ammonium oxidation process has been investigated at various ammonium and biomass concentrations. Using the oxygen uptake rate (OUR) method, a proportion of both active ammonium oxidizers (AAO) and nitrite oxidizers to the total suspended solids were separately estimated, and then tested to normalize the ammonium oxidation rate at various ammonium strengths and AAO concentrations. High-ammonium strength showed no significant inhibition to ammonium oxidation due to high-AAO concentration. It was demonstrated that the key factor deciding the specific ammonium oxidation rate was the ratio of ammonium concentration to the active nitrifiers (AN) concentration, but not the sole-variable such as initial ammonium concentration and AN concentration. Contois model was screened to suitably fit the ammonium oxidation kinetics under the high-ammonium loading condition, resulting in a half-saturation constant of 0.028 mg N mg^?1 AAO and a maximum specific ammonium oxidation rate of 3.56 g N g^?1 AAO d^?1.     

Real-time control strategy for nitrogen removal via nitrite in a SHARON reactor using pH and ORP sensors

This paper presents a real-time control strategy for nitrogen removal via nitrite in a continuous flow SHARON reactor using on-line available and industrially feasible sensors (pH and ORP). The developed control strategy optimizes the length of aerobic and anoxic phases as well as the external carbon source addition. This strategy, implemented in a laboratory-scale SHARON reactor fed with synthetic wastewater and real dewatering sludge supernatant, was able to cope with step variations in influent flow rate and ammonium concentration. The main advantages of this control strategy over the traditional operation mode with fixed carbon source dosification and fixed length cycle operation were: better effluent quality (ammonia concentration decreased from 12 to 2 mg NH₄–N L^?1 and nitrogen removal efficiency raised from 95% to 98%) as result of the shorter cycle length: 2.9 h versus 4.0 h, and savings in external carbon addition: 1332 mg COD d^?1 versus 2100 mg COD d^?1.     

Partial nitrification under limited dissolved oxygen conditions

Partial nitrification to nitrite is technically feasible and economically favourable, especially when wastewaters contained high ammonium concentrations or low C/N ratios. Partial nitrification can be obtained by selectively inhibiting nitrite-oxidizing bacteria (NOB) through appropriate regulation of the pH, temperature and dissolved oxygen (DO) concentrations. The effect of pH, DO levels and temperature on ammonia oxidation rate and nitrite accumulation was investigated in order to determine the optimal conditions for partial nitrification of synthetic wastewater with high ammonia concentration. The experiments performed at low DO levels to lower the total oxygen needed in the nitrification step, which means great saving in aeration. During the start-up stage pH and DO were set at 7.0–7.4 and 0.5 mg/l, respectively. The reactor was operated until complete partial nitrification was achieved. The effect of pH, DO on partial nitrification was studied, as pH was kept at 6.5, 7.5, 8.5, 9.5 and DO at 0.5±0.2, 1.5±0.2 and 2.5±0.2 mg/l, and temperature at 30 °C. The influence of temperature on k_a value was studied by keeping pH=7.5, DO=1.5 mg/l and temperature was controlled at 12, 20 and 30 °C, respectively. The results showed that partial nitrification to nitrite was steadily obtained and the optimal operational parameters were pH=7.5, DO=1.5 mg/l, T=30 °C based on ammonia oxidation rate and nitrite accumulation rate. The maximum k_a was achieved and to be 115.1×10⁻³ mg NH₄⁺–N (mg VSS h)⁻¹ under this condition.     

High-rate denitrifying sulfide removal process in expanded granular sludge bed reactor

An expanded granular sludge bed (EGSB) reactor was adopted to incubate bio-granules that could simultaneously convert 4.8 kg-S m^?3 d^?1 of sulfide in 97% efficiency; 2.6 kg-N m^?3 d^?1 of nitrate in 92% efficiency; and 2.7 kg-C m^?3 d^?1 acetate in 95% efficiency. Mass balance calculation of sulfur, nitrogen, and carbon over the EGSB reactor confirmed the performance results. This noted reactor performance is much higher than those reported in literature. Stoichiometric relation suggests that the nitrate was reduced to nitrite via autotrophic denitrification pathway, then the formed nitrite was converted via heterotrophic denitrification pathway to N₂.     

Control and optimization of nitrifying communities for nitritation from domestic wastewater at room temperatures

To achieve nitritation from complete-nitrification seed sludge at room temperature of 19 ± 1 °C, a lab-scale sequencing batch reactor (SBR) treating domestic wastewater with low C/N ratios was operated to investigate the control and optimization of nitrifying communities. Ammonia oxidizing bacteria (AOB) dominance was enhanced through the combination of low DO concentrations (<1.0 mg/L) and preset short-cycle control of aeration time. Nitritation was successfully established with NO₂^?-N/NO_x^?-N over 95%. To avoid the adverse impact of low DO concentrations on AOB activities, DO concentrations were increased to 1–2 mg/L. At the normal DO levels and temperatures, on-line control strategy of aerobic durations maintained the stability of nitritation with nitrite accumulation rate over 95% and ammonia removal above 97%. Fluorescence in-situ hybridization (FISH) analysis presented that the maximal percentage of AOB in biomass reached 10.9% and nitrite oxidizing bacteria (NOB) were washed out.     

Nitrogen removal performance in a novel combined biofilm reactor

Experiments have been performed to investigate the nitrogen removal performance in a novel combined biofilm reactor using synthetic wastewater. In the reactor, one cubic box was separated by two baffles into three zones: aerobic zone, buffering zone and anoxic zone. Nitrification and denitrification were supposed to be mainly accomplished in the aerobic and anoxic zones, respectively. When the influent total nitrogen (TN) and organic carbon loadings were averaged at 0.093 and 0.40 kg/m³/d, 84% TN removal efficiency was achieved by adjusting the aeration rate and the configuration of the reactor. Continuous experimental results demonstrated that NH₃-N removal efficiency increased by adjusting the clapboards of the reactor at a certain aeration rate. Energy produced by aeration was used for liquid recycle, so TN could be more efficiently removed at lower cost in this reactor.