Controlled-ph batch butanol-acetone fermentation by low acid producing Clostridium acetobutylicum B18

Summary C. acetobutylicum B18 produced a large amount of butanol over a wide range of pH (4.5–6.0). At pH 6.0 fermentation and cell growth were most active at pH 6.0, and the highest values of glucose consumption rate (4.37 g/L-h), butanol productivity (1.0 g/L-h), butyric acid recycle rate (0.31 g/L-h), and cell growth rate (0.2 h^-1) were obtained. There existed a critical pH between 6.0 and 6.5 above which cells switched to organic acid producing mode. Clostridial stage appeared essential for solvent production by strain B18 but sporulation was not necessary for solvent formation.     

Production of acetone and butanol by Clostridium acetobutylicum in continuous culture with cell recycle

Summary To increase the solvent productivity of the acetone-butanol fermentation, a continuous culture of Clostridium acetobytylicum with cell recycling was used. At a dry cell mass concentration of 8 g l^-1 and a dilution rate of D=0.64 h^-1, a solvent productivity of 5.4 g l^-1 h^-1 was attained. To prevent degeneration of the culture, which occurs with high concentrations of solvents (acetone, butanol and ethanol), different reactor cascades were used. A two-stage cascade with cell recycling and turbidostatic cell concentration control turned out to be the best solution, the first stage of which was kept at relatively low cell and product concentrations. A solvent productivity of 3 and 2.3 g l^-1 h^-1, respectively, was achieved at solvent concentrations of 12 and 15 g l^-1.Symbols D Dilution rate (h^-1) - r _p solvent productivity (g l^-1 h^-1) - s residual glucose concentration (g l^-1) - V _R reactor volume (l) - V _O overall volume (l) - x (dry) cell mass concentration (g l^-1) - Y _P/S solvent yield (g g^-1)     

Continuous and biomass recycle fermentations of Clostridium acetobutylicum

The availability and demand of biosynthetic energy (ATP) is an important factor in the regulation of solvent production in steady state continuous cultures of Clostridium acetobutylicum. The effect of biomass recycle at a variety of dilution rates and recycle ratios under both glucose and non-glucose limited conditions on product yields and selectivities has been investigated. Under conditions of non-glucose limitation, when the ATP supply is not growth-limiting, a lower growth rate imposed by biomass recycle leads to a reduced demand for ATP and substantially higher acetone and butanol yields. When the culture is glucose limited, however, biomass recycle results in lower solvent yields and higher acid yields.List of Symbols A ₆₀₀ absorbance at 600 nm - ATP adenosine triphosphate - C _imol/dm³ concentration of componenti in the fermentor - C _i ⁰ mol/dm³ concentration of componenti in the feed - D h^–1 dilution rate - F dm³/h feed flow rate - FdH₂ ferredoxin, reduced form - NAD nicotinamide adenine dinucleotide, oxidized form - NADH nicotinamide adenine dinucleotide, reduced form - NfF mmol/g/h NADH produced from oxidation of FdH₂ per unit biomass per unit time - P dm³/h filtrate flow during biomass recycle operation - PCRP C-mole carbon per C-mole glucose utilized percent of (substrate) carbon recovered in products - R recycle ratio,P/F - SPR mmol/g/h specific production rate - X _imol product/100 mol glucose utilized product yield - Y _ATP g biomass/mol ATP biomass yield on ATP - Y _GLU g biomass/mol glucose biomass yield on glucose - Y _ig biomass/mol biomass yield on nutrienti - h^–1 specific growth rate     

Continuous and biomass recycle fermentations of Clostridium acetobutylicum

Using experimental data from continuous cultures of Clostridium acetobutylicum with and without biomass recycle, relationships between product formation, growth and energetic parameters were explored, developed and tested. For glucose-limited cultures the maintenance models for, the Y _ATP and biomass yield on glucose, and were found valid, as well as the following relationships between the butanol (Y _B/G) or butyrate (Y _BE/G) yields and the ATP ratio (R _ATP, an energetic parameter), Y _B/G =0.82-1.35 R _ATP, Y _BE/G =0.54 + 1.90 R _ATP. For non-glucose-limited cultures the following correlations were developed, Y _B/G =0.57-1.07 , Y _B/G =0.82-1.35 R _ATPATP and similar equations for the ethanol yield. All these expressions are valid with and without biomass recycle, and independently of glucose feed or residual concentrations, biomass and product concentrations. The practical significance of these expressions is also discussed.List of Symbols D h^–1 dilution rate - m _e mol g^–1 h^–1 maintenance energy coefficient - m _G mol g^–1 h^–1 maintenance energy coefficient - R biomass recycle ratio, (dimensionless) - R _ATP ATP ratio (eqs.(5), (10) and (11)), (dimensionless) - X kg/m³ biomass concentration - Y _ATP g biomass per mol ATP biomass yield on ATP - Y _ATP ^max g biomass per mol ATP maximum Y _ATP - Y _A/G mol acetate produced per mol glucose consumed molar yield of acetate - y _an/g mol acetone produced per mol glucose consumed molar yield of acetone - Y _B/G mol butanol produced per mol glucose consumed molar yield of butanol - y _be/g mol butyrate produced per mol glucose consumed molar yield of butyrate - Y _E/G mol ethanol produced per mol glucose consumed molar yield of ethanol - Y _X/G g biomass per mol glucose consumed biomass yield on glucose - Y _ATP ^max g biomass per mol maximum Y _X/G glucose consumed - h^–1 specific growth rate     

Butyric fermentation: metabolic behaviour and production performance of Clostridium tyrobutyricum in a continuous culture with cell recycle

Summary Two physiological characteristics of butyric fermentation, inhibition by the acids produced, butyrate and acetate, and dependence on the growth rate of the distribution of these acids, prompted a study of butyrate production in a continuous fermentation system with cell recycle by microfiltration. The influence of the main operating parameters, glucose input (feed concentration and dilution rate) and bleed dilution rate on production of acids and biomass was studied. The performance of the system greatly exceeded the results obtained in batch and simple continuous fermentations as a high productivity for butyrate (9.5 g l^–1 h^–1) was achieved whilst retaining a satisfactory concentration of butyrate (29.7 g l^–1) and low acetate production (0.6 g l^–1) at a cell biomass concentration of 35 g l^–1. Cell growth rate was found to be a critical parameter for performance stability as oscillations in metabolic activity due to inhibition by acids were observed at bleed dilution rates below 0.016 h^–1.Offprint requests to: J. P. Vandecasteele     

Heterolactic fermentation by a homofermentative Lactobacillus sp. during glucose limitation in anaerobic continuous culture with complete cell recycle

E. BORCH, H. BERG AND O. HOLST. 1991. The homofermentative Lactobacillus sp. 93 SMRICC 235 was grown anaerobically in batch culture and subsequent continuous culture, with complete cell recycle at pH 6.0 and 25^.C, on a semi-defined medium. During cell recycle culture the biomass was concentrated in the fermenter to a final dry weight of 37 g/1 and a viable count of 10.6 log cfu/ml. The corresponding final values in batch culture were 2.4 g/1 and 9.3 log cfu/ml. A switch from homo- to heterolactic fermentation was observed during starvation, due to glucose depletion in the cell recycle culture. High levels of acetate and formate were produced in addition to ethanol. Amino acid profiles of hydrolysed samples showed extensive utilization of amino acids, particularly in cell recycle culture. Sulphide was produced during cell recycle culture. The change from homo- to heterolactic fermentation observed during semi-starvation is likely to affect the properties of lactobacilli as spoilage bacteria of meat and meat products, as well as starter cultures.     

Two-stage continuous fermentation of Clostridium acetobutylicum: effects of pH and dilution rate

Summary The kinetics of a two-stage continuous fermentation of Clostridium acetobutylicum have been studied. The pH and the dilution rate have been shown to be two essential factors for process optimization. An increase in pH or dilution rate in the first stage decreased solvent production in the second fermentor. To achieve optimal solvent production, the pH had to be maintained at 4.5 in the first stage and between 4.5 and 5.0 in the second stage. Dilution rates of 0.08 h^–1 and 0.04 h^–1,respectively, in the first and second fermentors allowed a high solvent concentration. When the pH was maintained at 4.5 in each stage and when the dilution rates were 0.08 h^–1 and 0.04 h^–1 in the first and second fermentors respectively, 21 g/l solvent concentration was achieved. A conversion yield of 0.36 g solvents/g glucose consumed was obtained with total consumption of glucose. Biomass was only produced in the first stage together with 40% of the solvents, indicating that solvent production had to be induced in the first fermentor. Offprint requests to: J. M. Engasser     

Reaction engineering studies of acetone-butanol-ethanol fermentation with Clostridium acetobutylicum

Acetone-butanol-ethanol (ABE) fermentation by Clostridium acetobutylicum has been extensively studied in recent years because the organism is recognized as an excellent butanol producer. A parallel bioreactor system with 48 stirred-tank bioreactors on a 12 mL scale was evaluated for batch cultivations of the strictly anaerobic, butanol-producing C. acetobutylicum ATCC 824. Continuous gassing with nitrogen gas was applied to control anaerobic conditions. Process performances of ABE batch fermentations on a milliliter scale were identical to the liter-scale stirred-tank reactor if reaction conditions were identical on the different scales (e.g., initial medium, pH, temperature, specific evaporation rates, specific power input by the stirrers). The effects of varying initial ammonia concentrations (0.1-4.4 g L(-1) ) were studied in parallel with respect to glucose consumption and butanol production of C. acetobutylicum ATCC 824 as a first application example. The highest butanol yield of 33% (mol mol(-1) ) was observed at initial ammonia concentrations of 0.5 and 1.1 g L(-1) . This is the first report on the successful application of a 48 parallel stirred-tank bioreactor system for reaction engineering studies of strictly anaerobic microorganisms at the milliliter scale.     

Effect of increased hydrogen partial pressure on the acetone-butanol fermentation by Clostridium acetobutylicum

Summary Elevated H₂ partial pressure in the acetone-butanol fermentation increased the butanol and ethanol yields on glucose by an average of 18% and 13%, respectively, while the respective yields of acetone and of the endogenous H₂ decreased by an average of 40% and 30%, and almost no effect was observed on the growth of the culture. The butanol to acetone ratio and the fraction of butanol in the total solvents were also increased with the H₂ pressure. There were no major differences in the observed pattern of change with pressurization at either t=0 or t=18 h. The results demonstrate the importance of H₂ partial pressure in the regulation of the C. acetobutylicum metabolism.     

In-line toxic product removal during solvent production by continuous fermentation using immobilized Clostridium acetobutylicum

Cells of Clostridium acetobutylicum were immobilized by adsorption onto bonechar, and used in a two-stage continuous reactor for solvent production from whey permeate. Gas-stripping (N₂ gas), an adsorbent resin (XAD-16) and a molecular sieve (silicalite) were evaluated for their use in between-stages solvent removal. All three techniques removed significant quantities of solvents, but not lactose, and allowed increases in sugar utilization and solvent productivity in the second stage. Gas stripping was the most successful technique, possibly because it removed only volatile solvents and not essential nutrients.     

Non-production of acetone and butanol by Clostridium acetobutylicum during glucose- and ammonium- limitation in continuous culture

Normal amounts of acetone and butanol were formed during the fermentation of glucose in a defined minimal medium in pH-regulated batch cultures (pH 5.0). No solventogenesis occurred during glucose- or ammonium-limited growth in a chemostat. Moreover, the capacity to produce solvents appeared to be lost during growth in continuous culture, apparently together with the ability to form endospores.     

Effect of nutrient limitation and two-stage continuous fermentor design on productivities during "Clostridium ragsdalei" syngas fermentation

The effect of three limiting nutrients, calcium pantothenate, vitamin B₁₂ and cobalt chloride (CoCl₂), on syngas fermentation using “Clostridium ragsdalei” was determined using serum bottle fermentation studies. Significant results from the bottle studies were translated into single- and two-stage continuous fermentor designs. Studies indicated that three-way interactions between the three limiting nutrients, and two-way interactions between vitamin B₁₂ and CoCl₂ had a significant positive effect on ethanol and acetic acid formation. In general, ethanol and acetic acid production ceased at the end of 9 days corresponding to the production of 2.01 and 1.95 g L⁻¹ for the above interactions. Reactor studies indicated the three-way nutrient limitation in two-stage fermentor showed improved acetic acid (17.51 g g⁻¹ cells) and ethanol (14.74 g g⁻¹ cells) yield compared to treatments in single-stage fermentors. These results further support the hypothesis that it is possible to modulate the product formation by limiting key nutrients during C. ragsdalei syngas fermentation.     

添加有机酸对Clostridium acetobutylicum合成丙酮和丁醇的影响

为提高丙酮-丁醇梭菌厌氧发酵生产丙酮和丁醇的能力,在发酵过程中添加有机酸（乙酸和丁酸）,考察其对菌体生长、溶剂合成影响。实验表明：当添加1.5 g/L乙酸时能够促进菌体的生长,促进丙酮的合成,在600 nm处的最大OD值比参照值高出18.4%,丙酮的最终质量分数提高了21.05%,但不能促进丁醇的合成;当添加1.0g/L丁酸时能够促进菌体生长,促进丁醇的合成,在600 nm处的最大OD比参照值高22.29%,丁醇的最终质量分数比对照组提高了24.32%,但不能促进丙酮的合成。     

电子载体对丁醇发酵的影响

研究在培养基中加入不同电子载体对丁醇发酵的影响。结果表明:添加微量的苄基紫精可以促进丁醇的产生,同时可强烈抑制丙酮的合成,丁醇体积分数由66.92%提高到82.35%。苄基紫精可促进菌株快速进入产溶剂期,发酵周期明显缩短,丁醇生产强度显著提高。7%玉米培养基中加入40 mg/L苄基紫精,丁醇产量最高达16.10 g/L,生产强度为0.37 g/(L.h),分别较对照提高10.96%和60.87%。在初始丁醇体积分数较低的条件下,苄基紫精对丁醇合成的促进作用更明显。     

High yeast concentration in continuous fermentation with cell recycle obtained by tangential microfiltration

Summary Continuous fermentation fed by 150 kg/m³ of glucose with total cell recycling by tangential microfiltration enabled yeasts concentration of 300 kg/m³ (dry weight) to be reached with a dilution rate of 0,5h^–1 and a cell viability greater than 75%. The stability of this system was tested for 50 residence times of the permeate. The method can be used both for the production of cell concentrates and for high rates of metabolite production.Nomenclature D. W. dry weight - X_T (kg/m³) total cell concentration D.W. - X_V (kg/m³) viable cell concentration D.W. - V viability of cell culture in per cent of total cell concentration - S (kg/m³) glucose concentration - P (kg/m³) ethanol concentration - D (h) dilution rate - R (kg/kg) fermentation yield - (h) specific growth rate - vp(kg/kg/h) specific alcohol production rate - (m) yeast size - (kg/kg) kg of intracellular water per kg of dry cells     

Metabolic engineering of Clostridium acetobutylicum ATCC 824 for isopropanol-butanol-ethanol fermentation

Clostridium acetobutylicum naturally produces acetone as well as butanol and ethanol. Since acetone cannot be used as a biofuel, its production needs to be minimized or suppressed by cell or bioreactor engineering. Thus, there have been attempts to disrupt or inactivate the acetone formation pathway. Here we present another approach, namely, converting acetone to isopropanol by metabolic engineering. Since isopropanol can be used as a fuel additive, the mixture of isopropanol, butanol, and ethanol (IBE) produced by engineered C. acetobutylicum can be directly used as a biofuel. IBE production is achieved by the expression of a primary/secondary alcohol dehydrogenase gene from Clostridium beijerinckii NRRL B-593 (i.e., adh(B-593)) in C. acetobutylicum ATCC 824. To increase the total alcohol titer, a synthetic acetone operon (act operon; adc-ctfA-ctfB) was constructed and expressed to increase the flux toward isopropanol formation. When this engineering strategy was applied to the PJC4BK strain lacking in the buk gene (encoding butyrate kinase), a significantly higher titer and yield of IBE could be achieved. The resulting PJC4BK(pIPA3-Cm2) strain produced 20.4 g/liter of total alcohol. Fermentation could be prolonged by in situ removal of solvents by gas stripping, and 35.6 g/liter of the IBE mixture could be produced in 45 h.