Mushroom spent straw: a potential substrate for an ethanol-based biorefinery

Rice straw (RS) is an important lignocellulosic biomass with nearly 800 million dry tons produced annually worldwide. RS has immense potential as a lignocellulosic feedstock for making renewable fuels and chemicals in a biorefinery. However, because of its natural recalcitrance, RS needs thermochemical treatment prior to further biological processing. Ammonia fiber expansion (AFEX) is a leading biomass pretreatment process utilizing concentrated/liquefied ammonia to pretreat lignocellulosic biomass at moderate temperatures (70–140°C). Previous research has shown improved cellulose and hemicellulose conversions upon AFEX treatment of RS at 2:1 ammonia to biomass (w/w) loading, 40% moisture (dwb) and 90°C. However, there is still scope for further improvement. Fungal pretreatment of lignocellulosics is an important biological pretreatment method that has not received much attention in the past. A few reasons for ignoring fungal-based pretreatments are substantial loss in cellulose and hemicellulose content and longer pretreatment times that reduce overall productivity. However, the sugar loss can be minimized through use of white-rot fungi (e.g. Pleutorus ostreatus) over a much shorter duration of pretreatment time. It was found that mushroom spent RS prior to AFEX allowed reduction in thermochemical treatment severity, while resulting in 15% higher glucan conversions than RS pretreated with AFEX alone. In this work, we report the effect of fungal conditioning of RS followed by AFEX pretreatment and enzymatic hydrolysis. The recovery of other byproducts from the fungal conditioning process such as fungal enzymes and mushrooms are also discussed. JIMB-2008: BioEnergy—Special issue.     

Enzymatic digestion of liquid hot water pretreated hybrid poplar

Liquid hot (LHW) water pretreatment (LHW) of lignocellulosic material enhances enzymatic conversion of cellulose to glucose by solubilizing hemicellulose fraction of the biomass, while leaving the cellulose more reactive and accessible to cellulase enzymes. Within the range of pretreatment conditions tested in this study, the optimized LHW pretreatment conditions for a 15% (wt/vol) slurry of hybrid poplar were found to be 200^oC, 10 min, which resulted in the highest fermentable sugar yield with minimal formation of sugar decomposition products during the pretreatment. The LHW pretreatment solubilized 62% of hemicellulose as soluble oligomers. Hot‐washing of the pretreated poplar slurry increased the efficiency of hydrolysis by doubling the yield of glucose for a given enzyme dose. The 15% (wt/vol) slurry of hybrid poplar, pretreated at the optimal conditions and hot‐washed, resulted in 54% glucose yield by 15 FPU cellulase per gram glucan after 120 h. The hydrolysate contained 56 g/L glucose and 12 g/L xylose. The effect of cellulase loading on the enzymatic digestibility of the pretreated poplar is also reported. Total monomeric sugar yield (glucose and xylose) reached 67% after 72 h of hydrolysis when 40 FPU cellulase per gram glucan were used. An overall mass balance of the poplar‐to‐ethanol process was established based on the experimentally determined composition and hydrolysis efficiencies of the liquid hot water pretreated poplar. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Pretreatments to enhance the digestibility of lignocellulosic biomass

Lignocellulosic biomass represents a rather unused source for biogas and ethanol production. Many factors, like lignin content, crystallinity of cellulose, and particle size, limit the digestibility of the hemicellulose and cellulose present in the lignocellulosic biomass. Pretreatments have as a goal to improve the digestibility of the lignocellulosic biomass. Each pretreatment has its own effect(s) on the cellulose, hemicellulose and lignin; the three main components of lignocellulosic biomass. This paper reviews the different effect(s) of several pretreatments on the three main parts of the lignocellulosic biomass to improve its digestibility. Steam pretreatment, lime pretreatment, liquid hot water pretreatments and ammonia based pretreatments are concluded to be pretreatments with high potentials. The main effects are dissolving hemicellulose and alteration of lignin structure, providing an improved accessibility of the cellulose for hydrolytic enzymes.     

Hydrolysis of lignocellulosic materials for ethanol production: a review

Lignocellulosic biomass can be utilized to produce ethanol, a promising alternative energy source for the limited crude oil. There are mainly two processes involved in the conversion: hydrolysis of cellulose in the lignocellulosic biomass to produce reducing sugars, and fermentation of the sugars to ethanol. The cost of ethanol production from lignocellulosic materials is relatively high based on current technologies, and the main challenges are the low yield and high cost of the hydrolysis process. Considerable research efforts have been made to improve the hydrolysis of lignocellulosic materials. Pretreatment of lignocellulosic materials to remove lignin and hemicellulose can significantly enhance the hydrolysis of cellulose. Optimization of the cellulase enzymes and the enzyme loading can also improve the hydrolysis. Simultaneous saccharification and fermentation effectively removes glucose, which is an inhibitor to cellulase activity, thus increasing the yield and rate of cellulose hydrolysis.     

Two-stage pretreatment of rice straw using aqueous ammonia and dilute acid

Liberation of fermentable sugars from recalcitrant lignocellulosic biomass is one of the key challenges in production of cellulosic ethanol. Here we developed a two-stage pretreatment process using aqueous ammonia and dilute sulfuric acid in a percolation mode to improve production of fermentable sugars from rice straw. Aqueous NH? was used in the first stage which removed lignin selectively but left most of cellulose (97%) and hemicellulose (77%). Dilute acid was applied in the second stage which removed most of hemicellulose, partially disrupted the crystalline structure of cellulose, and thus enhanced enzymatic digestibility of cellulose in the solids remaining. Under the optimal pretreatment conditions, the enzymatic hydrolysis yields of the two-stage treated samples were 96.9% and 90.8% with enzyme loadings of 60 and 15FPU/g of glucan, respectively. The overall sugar conversions of cellulose and hemicellulose into glucose and xylose by enzymatic and acid hydrolysis reached 89.0% and 71.7%, respectively.     

Pretreatments for Enhanced Enzymatic Hydrolysis of Pinewood: a Review

Pinewood is an abundant source of lignocellulosic biomass that has potential to be used as renewable feedstock in biorefineries for conversion into advanced biofuels and other value-added chemicals. However, its structural recalcitrance, due to the compact packing of its major components, viz. cellulose, hemicellulose and lignin, high lignin content, and high cellulose crystallinity, is a major bottleneck in its widespread use as a biorefinery feedstock. Typical chemical, thermal, and biological pretreatment technologies are aimed at removing lignin and hemicellulose fractions for improving enzyme accessibility and digestibility of cellulose. This review highlights common pine pretreatment procedures, associated key parameters and resulting enzymatic hydrolysis yields. The challenges and limitations are also discussed as well as potential strategies to overcome them, providing an essential source of information to realize pine as a compelling biorefinery biomass source.     

Cellulose accessibility limits the effectiveness of minimum cellulase loading on the efficient hydrolysis of pretreated lignocellulosic substrates

A range of lignocellulosic feedstocks (including agricultural, softwood and hardwood substrates) were pretreated with either sulfur dioxide-catalyzed steam or an ethanol organosolv procedure to try to establish a reliable assessment of the factors governing the minimum protein loading that could be used to achieve efficient hydrolysis. A statistical design approach was first used to define what might constitute the minimum protein loading (cellulases and β-glucosidase) that could be used to achieve efficient saccharification (defined as at least 70% glucan conversion) of the pretreated substrates after 72 hours of hydrolysis. The likely substrate factors that limit cellulose availability/accessibility were assessed, and then compared with the optimized minimum amounts of protein used to obtain effective hydrolysis. The optimized minimum protein loadings to achieve efficient hydrolysis of seven pretreated substrates ranged between 18 and 63 mg protein per gram of glucan. Within the similarly pretreated group of lignocellulosic feedstocks, the agricultural residues (corn stover and corn fiber) required significantly lower protein loadings to achieve efficient hydrolysis than did the pretreated woody biomass (poplar, douglas fir and lodgepole pine). Regardless of the substantial differences in the source, structure and chemical composition of the feedstocks, and the difference in the pretreatment technology used, the protein loading required to achieve efficient hydrolysis of lignocellulosic substrates was strongly dependent on the accessibility of the cellulosic component of each of the substrates. We found that cellulose-rich substrates with highly accessible cellulose, as assessed by the Simons' stain method, required a lower protein loading per gram of glucan to obtain efficient hydrolysis compared with substrates containing less accessible cellulose. These results suggest that the rate-limiting step during hydrolysis is not the catalytic cleavage of the cellulose chains per se, but rather the limited accessibility of the enzymes to the cellulose chains due to the physical structure of the cellulosic substrate.     

Hemicellulases and auxiliary enzymes for improved conversion of lignocellulosic biomass to monosaccharides

Background  

High enzyme loading is a major economic bottleneck for the commercial processing of pretreated lignocellulosic biomass to produce fermentable sugars. Optimizing the enzyme cocktail for specific types of pretreated biomass allows for a significant reduction in enzyme loading without sacrificing hydrolysis yield. This is especially important for alkaline pretreatments such as Ammonia fiber expansion (AFEX) pretreated corn stover. Hence, a diverse set of hemicellulases supplemented along with cellulases is necessary for high recovery of monosaccharides.     

Conversion for Avicel and AFEX pretreated corn stover by Clostridium thermocellum and simultaneous saccharification and fermentation: insights into microbial conversion of pretreated cellulosic biomass

In this study, efforts were taken to compare solubilization of Avicel and AFEX pretreated corn stover (AFEX CS) by SSF and Clostridium thermocellum fermentation, with an aim to gain insights into microbial conversion of pretreated cellulosic biomass. Solubilization rates for AFEX CS are comparable for the two systems while solubilization of Avicel is much faster by C. thermocellum. Initial catalyst loading impacts final cellulose conversion for SSF but not for C. thermocellum. Hydrolysis of the two substrates using cell-free C. thermocellum fermentation broth revealed much smaller difference in cellulose conversion than the difference observed for growing cultures. Tests on hemicellulose removal and particle size reduction for AFEX CS indicated that substrate accessibility is very important for enhanced solubilization by C. thermocellum.     

Features of promising technologies for pretreatment of lignocellulosic biomass

Cellulosic plant material represents an as-of-yet untapped source of fermentable sugars for significant industrial use. Many physio-chemical structural and compositional factors hinder the enzymatic digestibility of cellulose present in lignocellulosic biomass. The goal of any pretreatment technology is to alter or remove structural and compositional impediments to hydrolysis in order to improve the rate of enzyme hydrolysis and increase yields of fermentable sugars from cellulose or hemicellulose. These methods cause physical and/or chemical changes in the plant biomass in order to achieve this result. Experimental investigation of physical changes and chemical reactions that occur during pretreatment is required for the development of effective and mechanistic models that can be used for the rational design of pretreatment processes. Furthermore, pretreatment processing conditions must be tailored to the specific chemical and structural composition of the various, and variable, sources of lignocellulosic biomass. This paper reviews process parameters and their fundamental modes of action for promising pretreatment methods.     

Influence of physico-chemical changes on enzymatic digestibility of ionic liquid and AFEX pretreated corn stover

Ionic liquid (IL) and ammonia fiber expansion (AFEX) pretreatments were studied to develop the first direct side-by-side comparative assessment on their respective impacts on biomass structure, composition, process mass balance, and enzymatic saccharification efficiency. AFEX pretreatment completely preserves plant carbohydrates, whereas IL pretreatment extracts 76% of hemicellulose. In contrast to AFEX, the native crystal structure of the recovered corn stover from IL pretreatment was significantly disrupted. For both techniques, more than 70% of the theoretical sugar yield was attained after 48 h of hydrolysis using commercial enzyme cocktails. IL pretreatment requires less enzyme loading and a shorter hydrolysis time to reach 90% yields. Hemicellulase addition led to significant improvements in the yields of glucose and xylose for AFEX pretreated corn stover, but not for IL pretreated stover. These results provide new insights into the mechanisms of IL and AFEX pretreatment, as well as the advantages and disadvantages of each.     

Effect of hemicellulose and lignin removal on enzymatic hydrolysis of steam pretreated corn stover

Ethanol can be produced from lignocellulosic biomass using steam pretreatment followed by enzymatic hydrolysis and fermentation. The sugar yields, from both hemicellulose and cellulose are critical parameters for an economically-feasible ethanol production process. This study shows that a near-theoretical glucose yield (96-104%) from acid-catalysed steam pretreated corn stover can be obtained if xylanases are used to supplement cellulases during hydrolysis. Xylanases hydrolyse residual hemicellulose, thereby improving the access of enzymes to cellulose. Under these conditions, xylose yields reached 70-74%. When pre-treatment severity was reduced by using autocatalysis instead of acid-catalysed steam pretreatment, xylose yields were increased to 80-86%. Partial delignification of pretreated material was also evaluated as a way to increase the overall sugar yield. The overall glucose yield increased slightly due to delignification but the overall xylose yield decreased due to hemicellulose loss in the delignification step. The data also demonstrate that steam pretreatment is a robust process: corn stover from Europe and North America showed only minor differences in behaviour.     

Fractionating recalcitrant lignocellulose at modest reaction conditions

Effectively releasing the locked polysaccharides from recalcitrant lignocellulose to fermentable sugars is among the greatest technical and economic barriers to the realization of lignocellulose biorefineries because leading lignocellulose pre-treatment technologies suffer from low sugar yields, and/or severe reaction conditions, and/or high cellulase use, narrow substrate applicability, and high capital investment, etc. A new lignocellulose pre-treatment featuring modest reaction conditions (50 degrees C and atmospheric pressure) was demonstrated to fractionate lignocellulose to amorphous cellulose, hemicellulose, lignin, and acetic acid by using a non-volatile cellulose solvent (concentrated phosphoric acid), a highly volatile organic solvent (acetone), and water. The highest sugar yields after enzymatic hydrolysis were attributed to no sugar degradation during the fractionation and the highest enzymatic cellulose digestibility ( approximately 97% in 24 h) during the hydrolysis step at the enzyme loading of 15 filter paper units of cellulase and 60 IU of beta-glucosidase per gram of glucan. Isolation of high-value lignocellulose components (lignin, acetic acid, and hemicellulose) would greatly increase potential revenues of a lignocellulose biorefinery.     

评价木质纤维素预处理效果的新方法

以玉米秸秆为代表性纤维质原料,尝试建立一种评估预处理效果的新方法——持水率测定法,即:将试样在室温下浸泡1 h,在分离因数1 000下离心5 min后测定持水率。结果表明:在机理上木质纤维的持水率与可消化性具有一致性,在某种程度上具有正相关性;持水率作为一种简单快捷的新型测定方法,能够用来评估木质纤维素类生物质的预处理效果,不同预处理方法通过打破木质纤维的复杂致密结构,破坏氢键和酯键作用增加其孔径和孔穴,同时使其暴露出更多的游离羟基等亲水性基团,最终增加了木质纤维的持水率。     

Combining hot-compressed water and ball milling pretreatments to improve the efficiency of the enzymatic hydrolysis of eucalyptus

Background  

Lignocellulosic biomass such as wood is an attractive material for fuel ethanol production. Pretreatment technologies that increase the digestibility of cellulose and hemicellulose in the lignocellulosic biomass have a major influence on the cost of the subsequent enzymatic hydrolysis and ethanol fermentation processes. Pretreatments without chemicals such as acids, bases or organic solvents are less effective for an enzymatic hydrolysis process than those with chemicals, but they have a less negative effect on the environment.     

Synthetic enzyme mixtures for biomass deconstruction: Production and optimization of a core set

The high cost of enzymes is a major bottleneck preventing the development of an economically viable lignocellulosic ethanol industry. Commercial enzyme cocktails for the conversion of plant biomass to fermentable sugars are complex mixtures containing more than 80 proteins of suboptimal activities and relative proportions. As a step toward the development of a more efficient enzyme cocktail for biomass conversion, we have developed a platform, called GENPLAT, that uses robotic liquid handling and statistically valid experimental design to analyze synthetic enzyme mixtures. Commercial enzymes (Accellerase 1000 +/? Multifect Xylanase, and Spezyme CP +/? Novozyme 188) were used to test the system and serve as comparative benchmarks. Using ammonia‐fiber expansion (AFEX) pretreated corn stover ground to 0.5 mm and a glucan loading of 0.2%, an enzyme loading of 15 mg protein/g glucan, and 48 h digestion at 50°C, commercial enzymes released 53% and 41% of the available glucose and xylose, respectively. Mixtures of three, five, and six pure enzymes of Trichoderma species, expressed in Pichia pastoris, were systematically optimized. Statistical models were developed for the optimization of glucose alone, xylose alone, and the average of glucose + xylose for two digestion durations, 24 and 48 h. The resulting models were statistically significant (P < 0.0001) and indicated an optimum composition for glucose release (values for optimized xylose release are in parentheses) of 29% (5%) cellobiohydrolase 1, 5% (14%) cellobiohydrolase 2, 25% (25%) endo‐β1,4‐glucanase 1, 14% (5%) β‐glucosidase, 22% (34%) endo‐β1,4‐xylanase 3, and 5% (17%) β‐xylosidase in 48 h at a protein loading of 15 mg/g glucan. Comparison of two AFEX‐treated corn stover preparations ground to different particle sizes indicated that particle size (100 vs. 500 µm) makes a large difference in total digestibility. The assay platform and the optimized “core” set together provide a starting point for the rapid testing and optimization of alternate core enzymes from other microbial and recombinant sources as well as for the testing of “accessory” proteins for development of superior enzyme mixtures for biomass conversion. Biotechnol. Bioeng. 2010;106: 707–720. © 2010 Wiley Periodicals, Inc.     

AFEX Pretreatment and Enzymatic Conversion of Black Locust (Robinia pseudoacacia L.) to Soluble Sugars

Black locust (Robinia pseudoacacia L.), like willow and poplar, is a hardwood species which can be grown in coppice for bioenergy production, and because of its nitrogen-fixing ability, it can be cultivated with higher yields on less productive land. For these experiments, we examined the feasibility of using ammonia fiber expansion (AFEX) pretreatment to increase the saccharification yields from black locust grown for bioethanol production, as well as examine the impact of posttreatments (hot-water washing and additional size reduction) on sugar yields. The optimal AFEX conditions for black locust were 180°C, 1.0?g NH₃/g dry biomass, 2.5?g H₂O/g dry biomass, for 30?min residence time, and of the parameters tested, temperature had the greatest impact on yields. Yields from the sample without posttreatment and hydrolyzed at the standard enzyme loading were very low: <30% glucose and ??50% hemicellulose. Both hot-water washing and size reduction improved yields; however, size reduction had a more significant effect indicating that increasing enzyme accessibility is more important for digestibility as opposed to the removal of soluble inhibitors. The effect of size reduction was comparable to that obtained by quadrupling the enzyme loading, increasing glucose yields by ??20?C30% and hemicellulose yields by ??20%. Untreated black locust is known to contain compounds which are inhibitory to both enzymes and microorganisms and AFEX pretreatment neutralizes this inhibitory effect to some extent.     

Biodetoxification of toxins generated from lignocellulose pretreatment using a newly isolated fungus, Amorphotheca resinae ZN1, and the consequent ethanol fermentation

Background

Enzymes for plant cell wall deconstruction are a major cost in the production of ethanol from lignocellulosic biomass. The goal of this research was to develop optimized synthetic mixtures of enzymes for multiple pretreatment/substrate combinations using our high-throughput biomass digestion platform, GENPLAT, which combines robotic liquid handling, statistical experimental design and automated Glc and Xyl assays. Proportions of six core fungal enzymes (CBH1, CBH2, EG1, β-glucosidase, a GH10 endo-β1,4-xylanase, and β-xylosidase) were optimized at a fixed enzyme loading of 15 mg/g glucan for release of Glc and Xyl from all combinations of five biomass feedstocks (corn stover, switchgrass, Miscanthus, dried distillers' grains plus solubles [DDGS] and poplar) subjected to three alkaline pretreatments (AFEX, dilute base [0.25% NaOH] and alkaline peroxide [AP]). A 16-component mixture comprising the core set plus 10 accessory enzymes was optimized for three pretreatment/substrate combinations. Results were compared to the performance of two commercial enzymes (Accellerase 1000 and Spezyme CP) at the same protein loadings.

Results

When analyzed with GENPLAT, corn stover gave the highest yields of Glc with commercial enzymes and with the core set with all pretreatments, whereas corn stover, switchgrass and Miscanthus gave comparable Xyl yields. With commercial enzymes and with the core set, yields of Glc and Xyl were highest for grass stovers pretreated by AP compared to AFEX or dilute base. Corn stover, switchgrass and DDGS pretreated with AFEX and digested with the core set required a higher proportion of endo-β1,4-xylanase (EX3) and a lower proportion of endo-β1,4-glucanase (EG1) compared to the same materials pretreated with dilute base or AP. An optimized enzyme mixture containing 16 components (by addition of α-glucuronidase, a GH11 endoxylanase [EX2], Cel5A, Cel61A, Cip1, Cip2, β-mannanase, amyloglucosidase, α-arabinosidase, and Cel12A to the core set) was determined for AFEX-pretreated corn stover, DDGS, and AP-pretreated corn stover. The optimized mixture for AP-corn stover contained more exo-β1,4-glucanase (i.e., the sum of CBH1 + CBH2) and less endo-β1,4-glucanase (EG1 + Cel5A) than the optimal mixture for AFEX-corn stover. Amyloglucosidase and β-mannanase were the two most important enzymes for release of Glc from DDGS but were not required (i.e., 0% optimum) for corn stover subjected to AP or AFEX. As a function of enzyme loading over the range 0 to 30 mg/g glucan, Glc release from AP-corn stover reached a plateau of 60-70% Glc yield at a lower enzyme loading (5-10 mg/g glucan) than AFEX-corn stover. Accellerase 1000 was superior to Spezyme CP, the core set or the 16-component mixture for Glc yield at 12 h, but the 16-component set was as effective as the commercial enzyme mixtures at 48 h.

Conclusion

The results in this paper demonstrate that GENPLAT can be used to rapidly produce enzyme cocktails for specific pretreatment/biomass combinations. Pretreatment conditions and feedstock source both influence the Glc and Xyl yields as well as optimal enzyme proportions. It is predicted that it will be possible to improve synthetic enzyme mixtures further by the addition of additional accessory enzymes.     

Dissolution of cellulose from AFEX-pretreated Zoysia japonica in AMIMCl with ultrasonic vibration

In this study, 1-allyl-3-methylimidazolium chloride (AMIMCl), an ionic liquid, was synthesized and characterized by a series of test methods. Pretreatment of Zoysia japonica by ammonia fiber expansion (AFEX) was shown to reduce significantly the mass of hemicellulose and lignin in biomass, thereby breaking the lignocellulosic structure. Z. japonica samples pretreated with AFEX showed reasonable solubility in AMIMCl upon ultrasonic treatment. The rate of cellulose regeneration from Z. japonica samples pretreated with AFEX increased with increase in applied power of ultrasonication within a certain power range from 0 to 110 W. The regeneration rate of cellulose from AFEX-pretreated Z. japonica reached a maximum of 97% when the ultrasonic power was 110 W. Fourier transform infrared spectroscopy and nuclear magnetic resonance analyses indicated that the regenerated cellulose was similar to microcrystalline cellulose.     

Structural features affecting biomass enzymatic digestibility

The rate and extent of enzymatic hydrolysis of lignocellulosic biomass highly depend on enzyme loadings, hydrolysis periods, and structural features resulting from pretreatments. Furthermore, the influence of one structural feature on biomass digestibility varies with the changes in enzyme loading, hydrolysis period and other structural features as well. In this paper, the effects of lignin content, acetyl content, and biomass crystallinity on the 1-, 6-, and 72-h digestibilities with various enzyme loadings were investigated. To eliminate the cross effects among structural features, selective pretreatment techniques were employed to vary one particular structural feature during a pretreatment, while the other two structural features remained unchanged. The digestibility results showed that lignin content and biomass crystallinity dominated digestibility whereas acetyl content had a lesser effect. Lignin removal greatly enhanced the ultimate hydrolysis extent. Crystallinity reduction, however, tremendously increased the initial hydrolysis rate and reduced the hydrolysis time or the amount of enzyme required to attain high digestibility. To some extent, the effects of structural features on digestibility were interrelated. At short hydrolysis periods, lignin content was not important to digestibility when crystallinity was low. Similarly, at long hydrolysis periods, crystallinity was not important to digestibility when lignin content was low.