A customized fixation plate with novel structure designed by topological optimization for mandibular angle fracture based on finite element analysis

Background

The purpose of this study was to design a customized fixation plate for mandibular angle fracture using topological optimization based on the biomechanical properties of the two conventional fixation systems, and compare the results of stress, strain and displacement distributions calculated by finite element analysis (FEA).

Methods

A three-dimensional (3D) virtual mandible was reconstructed from CT images with a mimic angle fracture and a 1 mm gap between two bone segments, and then a FEA model, including volume mesh with inhomogeneous bone material properties, three loading conditions and constraints (muscles and condyles), was created to design a customized plate using topological optimization method, then the shape of the plate was referenced from the stress concentrated area on an initial part created from thickened bone surface for optimal calculation, and then the plate was formulated as “V” pattern according to dimensions of standard mini-plate finally. To compare the biomechanical behavior of the “V” plate and other conventional mini-plates for angle fracture fixation, two conventional fixation systems were used: type A, one standard mini-plate, and type B, two standard mini-plates, and the stress, strain and displacement distributions within the three fixation systems were compared and discussed.

Results

The stress, strain and displacement distributions to the angle fractured mandible with three different fixation modalities were collected, respectively, and the maximum stress for each model emerged at the mandibular ramus or screw holes. Under the same loading conditions, the maximum stress on the customized fixation system decreased 74.3, 75.6 and 70.6% compared to type A, and 34.9, 34.1, and 39.6% compared to type B. All maximum von Mises stresses of mandible were well below the allowable stress of human bone, as well as maximum principal strain. And the displacement diagram of bony segments indicated the effect of treatment with different fixation systems.

Conclusions

The customized fixation system with topological optimized structure has good biomechanical behavior for mandibular angle fracture because the stress, strain and displacement within the plate could be reduced significantly comparing to conventional “one mini-plate” or “two mini-plates” systems. The design methodology for customized fixation system could be used for other fractures in mandible or other bones to acquire better mechanical behavior of the system and improve stable environment for bone healing. And together with SLM, the customized plate with optimal structure could be designed and fabricated rapidly to satisfy the urgent time requirements for treatment.

     

Robust human body model injury prediction in simulated side impact crashes

This study developed a parametric methodology to robustly predict occupant injuries sustained in real-world crashes using a finite element (FE) human body model (HBM). One hundred and twenty near-side impact motor vehicle crashes were simulated over a range of parameters using a Toyota RAV4 (bullet vehicle), Ford Taurus (struck vehicle) FE models and a validated human body model (HBM) Total HUman Model for Safety (THUMS). Three bullet vehicle crash parameters (speed, location and angle) and two occupant parameters (seat position and age) were varied using a Latin hypercube design of Experiments. Four injury metrics (head injury criterion, half deflection, thoracic trauma index and pelvic force) were used to calculate injury risk. Rib fracture prediction and lung strain metrics were also analysed. As hypothesized, bullet speed had the greatest effect on each injury measure. Injury risk was reduced when bullet location was further from the B-pillar or when the bullet angle was more oblique. Age had strong correlation to rib fractures frequency and lung strain severity. The injuries from a real-world crash were predicted using two different methods by (1) subsampling the injury predictors from the 12 best crush profile matching simulations and (2) using regression models. Both injury prediction methods successfully predicted the case occupant's low risk for pelvic injury, high risk for thoracic injury, rib fractures and high lung strains with tight confidence intervals. This parametric methodology was successfully used to explore crash parameter interactions and to robustly predict real-world injuries.     

Mandibular reconstruction in the radiated patient: the role of osteocutaneous free tissue transfers

This paper discusses our experience with the second metatarsal and iliac crest osteocutaneous transfers for mandibular reconstruction. The prime indication for this type of reconstruction was for anterior mandibular defects when the patient had been previously resected. Midbody to midbody defects were reconstructed with the metatarsal and larger defects with the iliac crest. In most cases, an osteotomy was done to create a mental angle. The evaluation of speech, oral continence, and swallowing revealed good results in all patients unless lip or tongue resection compromised function. Facial contour was excellent in metatarsal reconstructions. The iliac crest cutaneous flap provided a generous supply of skin for both intraoral reconstruction and external skin coverage but tended to be bulky, particularly when used in the submental area. Thirty three of 36 flaps survived completely. Flap losses were due to anastomosis thrombosis (1), pedicle compression (1), and pedicle destruction during exploration for suspected carotid blowout (1). Ninety three percent of bone junctions developed a solid bony union despite the mandible having had a full therapeutic dose of preoperative radiation. Despite wound infections in 8 patients, and intraoral dehiscence with bone exposure in 12 patients, all but one of these transfers went on to good bony union without infection in the bone graft.     

Does the angulation of the mandibular third molar influence the fragility of the mandibular angle after trauma to the mandibular body? A three-dimensional finite-element study

The relationship between mandibular third molar (M3) angulation and mandibular angle fragility is not well established. The aim of this study was to evaluate the impact of M3 angulation on the mandibular angle fragility when submitted to a trauma to the mandibular body region. A three-dimensional (3D) mandibular model without M3 (Model 0) was obtained by means of finite-element analysis (FEA). Four models were generated from the initial model, representing distoangular (Model D), horizontal (Model H), mesioangular (Model M) and vertical (Model V) angulations. A blunt trauma with a magnitude of 2000 N was applied perpendicularly to the sagittal plane in the mandibular body. Maximum principal stress (P_max) (tensile stress) values were calculated in the bone. The lowest P_max stress values were noted in Model 0. When the M3 was present extra stress fields were found around marginal bone of second molar and M3. Comparative analysis of the models with M3 revealed that the highest level of stress was found in Model V, whereas Model D showed the lowest stress values. The angulation of M3 affects the stress levels in the mandibular angle and has an impact on mandibular fragility. The mandibular angle becomes more fragile in case of vertical impaction when submitted to a trauma to the mandibular body region.     

Mandibular angle reduction versus mandible reduction

The terms "mandibular angle reduction" and "reduction angleplasty" refer to operations to reduce the width of the lower face and change a square face to an oval one. Because the terms emphasize the word angle, however, they imply that the operations apply to the mandibular angle. The most frequent complaint after these operations is that the change in the lateral appearance is clear but that the change in the frontal appearance is not noticeable. Such a result is related to the fact that bone resection is performed mainly in the mandibular angle area and is focused particularly on resection of the posterior projection through curved ostectomy. That is, because operations limited to the mandibular angle area cannot properly satisfy patients' requirements, the operation must be applied to a larger area. Therefore, it seems reasonable to change the terms "mandibular angle reduction" and "reduction angleplasty" to "mandible reduction" and "reduction mandibuloplasty." In addition, the most important technique in the operation is the resection of the outer cortex of the mandible. In particular, the corticectomy technique using a reciprocating saw is quite safe and effective for the maximum resection of lateral flaring within a very short time.     

Three-dimensional finite element stress analysis of the dentate human mandible.

The biomechanical events which accompany functional loading of the human mandible are not fully understood. The techniques normally used to record them are highly invasive. Computer modelling offers a promising alternative approach in this regard, with the additional ability to predict regional stresses and strains in inaccessible locations. In this study, we built two three-dimensional finite element (FE) models of a human mandible reconstructed from tomographs of a dry dentate jaw. The first model was used for a complete mechanical characterization of physical events. It also provided comparative data for the second model, which had an increased vertical corpus depth. In both cases, boundary conditions included rigid restraints at the first right molar and endosteal cortical surfaces of the articular eminences of temporal bones. Groups of parallel multiple vectors simulated individual masticatory muscle loads. The models were solved for displacements, stresses, strains, and forces. The simulated muscle loads in the first model deformed the mandible helically upward and toward its right (working) side. The highest principal stresses occurred at the bite point, anterior aspects of the coronoid processes, symphyseal region, and right and left sides of the mandibular corpus. In general, the observed principal stresses and strains were highest on the periosteal cortical surface and alveolar bone. At the symphyseal region, maximum principal stresses and strains were highest on the lower lingual mandibular aspect, whereas minimum principal stresses and strains were highest on its upper labial side. Subcondylar principal strains and condylar forces were higher on the left (balancing or nonbiting) side than on the right mandibular side, with condylar forces more concentrated on the anteromedial aspect of the working-side condyle and on the central and lateral aspects of the left. When compared with in vivo strain data from macaques during comparable biting events, the predictive strain values from the first model were qualitatively similar. In the second model, the reduced tensile stress on the working-side, and decreased shear stress bilaterally, confirmed that lower stresses occurred on the lower mandibular border with increased jaw depth. Our results suggested that although the mandible behaved in a beam-like manner, its corpus acted more like a combination of open and closed cross sections due to the presence of tooth sockets, at least for the task modelled.(ABSTRACT TRUNCATED AT 400 WORDS)     

The effects of the periodontal ligament on mandibular stiffness: a study combining finite element analysis and geometric morphometrics

It is generally accepted that the periodontal ligament (PDL) plays a crucial role in transferring occlusal forces from the teeth to the alveolar bone. Studies using finite element analysis (FEA) have helped to better understand this role and show that the stresses and strains in the alveolar bone are influenced by whether and how PDL is included in FE models. However, when the overall distribution of stresses and strains in crania and mandibles are of interest, PDL is often not included in FE models, although little is known about how this affects the results. Here we study the effect of representing PDL as a layer of solid material with isotropic homogeneous properties in an FE model of a human mandible using a novel application of geometric morphometrics. The results show that the modelling of the PDL affects the deformation and thus strain magnitudes not only of the alveolar bone around the biting tooth, but that the whole mandible deforms differently under load. As a result, the strain in the mandibular corpus is significantly increased when PDL is included, while the strain in the bone beneath the biting tooth is reduced. These results indicate the importance of the PDL in FE studies. Thus we recommend that the PDL should be included in FE models of the masticatory apparatus, with tests to assess the sensitivity of the results to changes in the Young's modulus of the PDL material.     

Long term follow-up of reconstruction with allogeneic mandibular bone crib packed with autogenous particulate cancellous bone marrow

Allogeneic mandibular bone processed by the deep frozen method was used as a biologic crib for mandibular reconstruction. The allogeneic mandible is biocompatible, bioresorbable, of low antigenicity and provides the morphology for symphysis contour, angle of mandible and dental arch form. The particulate cancellous bone marrow (PCBM) contains marked osteogenic potential of hematopoietic marrow, which promotes osteogenesis. The cancellous marrow graft lacks structure and requires a crib to house it during the bone regeneration to the consolidation phase. Fresh frozen mandible was hollowed out for packing with PCBM prior to securing it to the defect by a rigid fixation method. Four cases of large mandibular defects resulting from treatment of benign odontogenic tumors were reconstructed utilizing this technique. All cases showed excellent facial contour and function satisfactorily in mastication and pronunciation. Complete graft incorporation and restoration of the osseous continuities were observed for four to 12 years after the operation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Elastic properties and masticatory bone stress in the macaque mandible

One important limitation of mechanical analyses with strain gages is the difficulty in directly estimating patterns of stress or loading in skeletal elements from strain measurements. Because of the inherent anisotropy in cortical bone, orientation of principal strains and stresses do not necessarily coincide, and it has been demonstrated theoretically that such differences may be as great as 45 degrees (Cowin and Hart, 1990). Likewise, relative proportions of stress and strain magnitudes may differ. This investigation measured the elastic properties of a region of cortical bone on both the buccal and lingual surfaces of the lower border of the macaque mandible. The elastic property data was then combined with macaque mandibular strain data from published and a new in vivo strain gage experiment to determine directions and magnitudes of maximum and minimum principal stresses. The goal was to compare the stresses and strains and assess the differences in orientation and relative magnitude between them. The main question was whether these differences might lead to different interpretations of mandibular function. Elastic and shear moduli, and Poisson's ratios were measured using an ultrasonic technique from buccal and lingual cortical surfaces in 12 macaque mandibles. Mandibular strain gage data were taken from a published set of experiments (Hylander, 1979), and from a new experiment in which rosette strain gauges were fixed to the buccal and lingual cortices of the mandibular corpus of an adult female Macaca fascicularis, after which bone strain was recorded during mastication. Averaged elastic properties were combined with strain data to calculate an estimate of stresses in the mandibular corpus. The elastic properties were similar to those of the human mandibular cortex. Near its lower border, the macaque mandible was most stiff in a longitudinal direction, less stiff in an inferosuperior direction, and least stiff in a direction normal to the bone's surface. The lingual aspect of the mandible was slightly stiffer than the buccal aspect. Magnitudes of stresses calculated from average strains ranged from a compressive stress of -16.00 GPa to a tensile stress of 8.84 GPa. The orientation of the principal stresses depended on whether the strain gage site was on the working or balancing side. On the balancing side of the mandibles, maximum principal stresses were oriented nearly perpendicular to the lower border of the mandible. On the working side of the mandibles, the orientation of the maximum principal stresses was more variable than on the balancing side, indicating a larger range of possible mechanisms of loading. Near the lower border of the mandible, differences between the orientation of stresses and strains were 12 degrees or less. Compared to ratios between maximum and minimum strains, ratios between maximum and minimum stresses were more divergent from a ratio of 1.0. Results did not provide any major reinterpretations of mandibular function in macaques, but rather confirmed and extended existing work. The differences between stresses and strains on the balancing side of the mandible generally supported the view that during the power stroke the mandible was bent and slightly twisted both during mastication and transducer biting. The calculated stresses served to de-emphasize the relative importance of torsion. On the working side, the greater range of variability in the stress analysis compared to the strain analysis suggested that a more detailed examination of loadings and stress patterns in each individual experiment would be useful to interpret the results. Torsion was evident on the working side; but in a number of experiments, further information was needed to interpret other superimposed regional loading patterns, which may have included parasagittal bending and reverse parasagittal bending.     

Influence of mastication and edentulism on mandibular bone density

The aim of this study was to demonstrate that external loading due to daily activities, including mastication, speech and involuntary open–close cycles of the jaw contributes to the internal architecture of the mandible. A bone remodelling algorithm that regulates the bone density as a function of stress and loading cycles is incorporated into finite element analysis. A three-dimensional computational model is constructed on the basis of computerised tomography (CT) images of a human mandible. Masticatory muscle activation involved during clenching is modelled by static analysis using linear optimisation. Other loading conditions are approximated by imposing mandibular flexure. The simulations predict that mandibular bone density distribution results in a tubular structure similar to what is observed in the CT images. Such bone architecture is known to provide the bone optimum strength to resist bending and torsion during mastication while reducing the bone mass. The remodelling algorithm is used to simulate the influence of edentulism on mandibular bone loss. It is shown that depending on the location and number of missing teeth, up to one-third of the mandibular bone mass can be lost due to lack of adequate mechanical stimulation.     

An assessment of impact strength of the mandible

In this study, an animal biomechanical study was performed to investigate the absorbed energy and impact strength of the mandible in relation to specimen position. Four regions of mandibles were loaded as complete pieces and gripped by the jaw of an Izod impact tester. All tests were carried out wet using the Izod impact test under two different impact loading directions, lateral and ventral.Absorbed energy and impact strength in kilojoules per square meter of specimen area were determined for each specimen. Under lateral impact loading, the absorbed energy was lowest for the anterior section due to the mental foramen's notch effect. The premolar region demonstrated more absorbed energy per unit area, or impact strength, than any other region. However, due to its small cross-sectional area, the premolar region also absorbs less impact energy.Under ventral impact loading conditions, anterior region absorbed twice as much impact energy than under lateral loading conditions. Premolar region absorbed the same impact energy under both lateral and ventral loading. Interestingly, mandibular angle under ventral loading absorbed five times more impact energy than under lateral loading. This behaviour is considered to be a mechanical adaptation to the actual loading of the mandible in vivo.     

Numerical studies of the influence of various geometrical features of a multispiked connecting scaffold prototype on mechanical stresses in peri-implant bone

Abstract

The multispiked connecting scaffold (MSC-scaffold) prototype is an essential innovation in the fixation of components of resurfacing arthroplasty (RA) endoprostheses, providing their entirely non-cemented and bone-tissue-preserving fixation in peri-articular bone. An FE study is proposed to evaluate the influence of geometrical features of the MSC-scaffold on the transfer of mechanical load in peri-implant bone. For this study, an FE model of Ti-Alloy MSC-scaffold prototype embedded in a bilinear elastic, transversely isotropic bone material was built. For the compressive load on the MSC-scaffold, maps of Huber-Mises-Hencky (HMH) stress in peri-implant bone were determined. The influence of the distance between the bases of neighbouring spikes, the apex angle of spikes, and the height of the spherical cup of spikes of the MSC-scaffold were analysed. It was found that the changes in the distance between the bases of neighbouring spikes from 0.2 to 0.5?mm cause the HMH stress to increase in bone material by 32%. The changes of the apex angle of spikes from 2° to 4° decrease the HMH stress in bone material by 39%. The changes of height of the spherical cup of spikes from 0 to 0.12?mm increase the HMH stress in bone material by 24%. In conclusion, the spikes’ apex angle and the distance between the bases of spikes of the MSC-scaffold are the key geometrical features determining the appropriate MSC-scaffold prototype design. The built FE model was found to be useful in bioengineering design of the novel fixation system for RA endoprostheses by means of the MSC-scaffold.     

Distraction osteogenesis of the porcine mandible: histomorphometric evaluation of bone

Distraction osteogenesis is a technique for skeletal lengthening that exploits the body's innate capacity for bone formation in response to tension forces on the repair callus. The authors developed a distraction osteogenesis model with a semiburied device in the Yucatan minipig mandible because of similarities between human and porcine mandibular anatomy, temporomandibular function, chewing patterns, and bone turnover rates. The purpose of this study was to measure histomorphometric bone fill after different latency periods, rates of distraction, and duration of neutral fixation in the minipig mandible. In addition, the relationship between histomorphometric bone fill and clinical stability was investigated. Mandibular osteotomies in 20 female Yucatan minipigs weighing 25 to 30 kg were distracted with modified semiburied distraction devices. Variables included 0-day or 4-day latency; 1-mm, 2-mm, or 4-mm daily distraction rates; gap size of 7 or 12 mm; and evaluation after neutral fixation for various lengths of time. Specimens were fixed in 2% paraformaldehyde, pH 7.4, before being embedded in methylmethacrylate. Sections were prepared from the region just below the inferior alveolar canal. The area of new bone formation within the gap was measured and expressed as a percentage of the total area of the distraction gap. Bone fill ranged from 0 to 100 percent. A pilot study with 7-mm advancements showed similar bone fill with 0-day or 4-day latency, but with poor reproducibility. Mandibles that were distracted to 12 mm at 1 mm per day exhibited nearly complete bone fill, either with 0-day latency (average, 93 percent) or 4-day latency (average, 100 percent). Mandibles that had been distracted for 3 days at 4 mm per day showed moderate osteogenesis and clinical stability with increasing time of neutral fixation. Bone fill was significantly correlated with clinical stability (Spearman r = 0.801, p = 0.001). Histological examination showed exuberant periosteal osteogenesis in distracted mandibles, even in those that showed poor bone fill and clinical stability. Thus, the periosteum appears to be a major source of new bone formation. These results show that osteogenesis was nearly complete with 1 mm per day and 0-day or 4-day latency. These results are consistent with the authors' previously reported clinical and radiographic observations that a latency period is not necessary for successful healing of the mandibular distraction osteogenesis wound.     

Effect of bone strain on cortical bone structure in macaques (Macaca mulatta)

It has recently been shown that the consistency of food significantly affects levels of bone strain in the mandible during mastication (Hylander, '79a). Mandibular bone histology was examined to test the effects of a diet of hard food compared to a diet of soft food in two group of monkeys. One group of rhesus macaques (Macaca mulatta) was fed a diet of commercially prepared hard biscuits. The second group was fed a soft diet the consistency of fudge. Both diets were nutritionally adequate for normal growth and development. As a control for other factors influencing cortical bone structure, fibular morphology was also examined. At the end of the test period, mandibular and fibular tissue samples from the two groups were prepared to determine the amount of secondary Haversian bone present. Mandibular depth at M₂ and fibular anteroposterior diameter were also measured and compared between the two dietary groups. The soft-diet monkeys showed low levels of remodeling in their mandibles. There were large patches of unremodeled bone and resorption spaces were common. The hard-diet monkeys exhibited more extensive evidence of secondary Haversian remodeling in their mandibles. The hard-diet monkeys also had deeper mandibles. In contrast, the fibulae from the two groups had similar mean diameters and showed comparable levels of secondary remodeling. We infer that the higher mandibular bone remodeling levels in the hard-diet monkeys represent an adaptive response to remove and replace fatigued mandibular bone due to higher stress levels associated with the ingestion and mastication of hard foods. We also infer that greater depth of the mandible at M₂ found in the harddiet group represents an adaptive response to higher stress levels associated with the ingestion and mastication of hard foods.     

Effect of unilateral partial facial paralysis on periosteal growth at the muscle-bone interface of facial muscles and facial bones

In a previous study, the influence of the midfacial musculature upon growth and development of the maxilla and mandible was established macroscopically. Dry skull measurements revealed a reduced premaxillary, maxillary, mandibular, and anterior corpus length with a simultaneous increase in mandibular ramal height on the paralyzed side. It was demonstrated that these reduced premaxillary and maxillary lengths were among others the result of reduced nasofrontal growth, whereas the increased ramal height was accompanied by condylar growth alterations. This study investigated whether the growth alterations at the mandibular corpus region could be explained by altered periosteal growth at the muscle-bone interface of the zygomatico-auricular muscle and the mandibular corpus, caused by altered muscle activity acting upon the periosteal sleeve. Fifty-six 12-day-old New Zealand White rabbits were randomly assigned to either a control or an experimental group. In the experimental group, left-sided partial facial paralysis was induced surgically when the animals were 12 days old. To study the muscle-bone interface, seven follow-up time intervals were defined between 3.5 and 60 days following the surgery. At these time intervals, four randomly selected control animals and four randomly selected experimental animals were killed. The anterior mandibular corpus region with the muscle-bone interface of the left control hemimandible and the left and right experimental hemimandibles was processed for undecalcified tissue preparation. Quantitative analysis of the total bone area at the muscle-bone interface revealed no significant differences between the left control hemimandible and the left and right experimental hemimandibles. Also, qualitative study of the histologic sections showed no major changes in the appearance or development of the trabecular pattern between the groups. However, slight differences in the distribution pattern of osteoblasts and osteoclasts along the bony surface were found between the left control hemimandible and the left and right experimental hemimandibles, which seemed to explain the alterations in mandibular corpus shape between these groups. It was suggested that these changes in the distribution pattern of osteoblasts and osteoclasts were the result of changes in the loading distribution pattern acting upon the mandible, caused by an altered neuromuscular recruitment pattern of the remaining functionally intact, mandibularly attached muscles. The latter was probably the result of adaptive mandibular positioning in response to an altered occlusal relationship, which was induced by the abnormal maxillary growth as a result of the unilateral partial facial paralysis.     

The course of the inferior alveolar nerve in the normal human mandibular ramus and in patients presenting for cosmetic reduction of the mandibular angles

This study was undertaken to quantify the path of the inferior alveolar nerve in the normal human mandible and in the mandibles of patients presenting for cosmetic reduction of the mandibular angles. The goals were: (1) to provide normative information that would assist the surgeon in avoiding injury to the nerve during surgery; (2) to characterize gender differences in the normal population; and (3) to compare the course of the nerve in the normal population to its course in a group of patients who presented with a complaint of "square face." The study was based upon the computerized tomographic scans of 10 normal patients (six men, four women) and 8 patients (all women) complaining of "square face." Using AnalyzePC 2.5 imaging software, the mandibles were segmented and the position of the nerve was recorded within its osseous canal in the mandibular ramus on each axial slice in which it was identifiable. Distances were calculated between the nerve and the anterior, posterior, lateral, and medial cortices. The positions of the lateral ramus prominence and the lowest point on the sigmoid notch were also recorded. The position of the mental foramen was recorded in relation to the nearest tooth, and the three-dimensional surface distances from the foramen to the alveolar bone, the inferior border of the mandible, and the mandibular symphysis were determined. The distances from the entrance of the nerve into the mandible to the lateral ramus prominence and the lowest point on the sigmoid notch were calculated. Summary statistics were obtained, comparing differences in gender. The nerve was identifiable in each ramus over a mean distance of 12.7 mm. On average, the lateral ramus prominence was 0.3 mm higher on the caudad-cephalad axis than the point at which the nerve entered the bone, whereas the location of the lowest point on the sigmoid notch was 16.6 mm above the nerve. The average distances from the nerve to the anterior, posterior, medial, and lateral cortices were 11.6, 12.1, 1.8, and 4.7 mm, respectively. Gender differences were significant for all of these except the medial cortex to nerve distance. On average, the mental foramen exited the body of the mandible immediately below the second premolar and the average surface distances from the foramen to the symphysis, the most cephalad alveolar bone, and the inferior border of the body were 30.9, 14.2, and 19.3 mm, respectively. With regard to the patients presenting for mandibular angle reduction, there were a few statistically significant but small scalar differences from normal controls.     

A modified human head model for the study of impact head injury

A recently published finite element (FE) head model is modified to consider the viscoelasticity of the meninges, the spongy and compact bone in the skull. The cerebrospinal fluid (CSF) is simulated explicitly as a hydrostatic fluid by using a surface-based fluid modelling method, which allows fluid and structure interaction. It is found that the modified model yields smoother pressure responses in a head impact simulation. The baseline model underestimated the peak von Mises stress in the brain by 15% and the peak principal stress in the skull by 33%. The increase in the maximum principal stress in the skull is mainly caused by the updation of the material's viscoelasticity, and the change in the maximum von Mises stress in the brain is mainly caused by the improvement of the CSF simulation. The study shows that the viscoelasticity of the head tissue should be considered, and that the CSF should be modelled as a fluid, when using FE analysis to study head injury due to impact.     

Intrauterine growth restriction affects bone mineral density of the mandible and the condyle in growing rats

Objectives:To investigate in growing rats the effect of intrauterine growth restriction (IUGR) on the bone mineral density of the mandible and tibia, as well as the quality of the mandibular and condylar bone.Methods:Twelve male rats were born IUGR by mothers sustaining 50% food restriction during pregnancy. Twelve control male rats were born by mothers fed ad libitum. Dual-energy X-ray absorptiometry (DEXA) of the tibia, proximal tibial metaphysis and the mandible, biochemical markers, histology and histomorphometrical analysis on the mandibular and subchondral bone of the condyle were performed.Results:IUGR significantly affected bone mineral density (BMD) of both tibial and mandibular bones. IUGR rats had significantly lower osteocalcin values (p=0.021) and phosphorus (p=0.028), but not 25-OH vitamin D (p=0.352). Bone area percentage in the mandible was significantly lower (51.21±5.54) in IUGR compared to controls (66.00±15.49), and for subchondral bone of the condyle for IUGR (47.01±6.82) compared to controls (68.27±13.37). IUGR had a significant reduction in the fibrous layer, but not the proliferating layer, with the hypertrophic layer significantly increased.Conclusion:Maternal restricted nutrition during gestation can affect BMD of the mandible and the tibia of the offspring animals.     

The relationship between split-line orientation and in vivo bone strain in galago (G. crassicaudatus) and macaque (Macaca mulatta and M. fascicularis) Mandibles

There is still disagreement concerning the functional significance of split-line patterns in bone. This study was undertaken to reexamine the mechanical forces hypothesis for split-line formation by comparing split-line patterns with in vivo mandibular bone strain patterns. The relationship between split-line orientation and in vivo stress and strain patterns on macaque and galago mandibles was examined during jaw opening and the power stroke of mastication and incision. An attempt was made to relate split-line orientation to the direction of tensile stress and strain along the primate mandible. In addition, we also investigated the alternative possibility that split-line orientation is related to the direction of low stresses (and strains) on the primate mandible. The results of this study showed that there was no consistent relationship between split-line orientation and the principal strains or stresses. Thus, split-lines did not run consistently in the direction of high or low stress and strain. Therefore, we have concluded that split-line orientation provides little useful information for inferring patterns of stress and strain in bone.     

Finite element and experimental cortex strains of the intact and implanted tibia

Finite Element (FE) models for the simulation of intact and implanted bone find their main purpose in accurately reproducing the associated mechanical behavior. FE models can be used for preclinical testing of joint replacement implants, where some biomechanical aspects are difficult, if not possible, to simulate and investigate in vitro. To predict mechanical failure or damage, the models should accurately predict stresses and strains. Commercially available synthetic femur models have been extensively used to validate finite element models, but despite the vast literature available on the characteristics of synthetic tibia, numerical and experimental validation of the intact and implant assemblies of tibia are very limited or lacking. In the current study, four FE models of synthetic tibia, intact and reconstructed, were compared against experimental bone strain data, and an overall agreement within 10% between experimental and FE strains was obtained. Finite element and experimental (strain gauge) models of intact and implanted synthetic tibia were validated based on the comparison of cortex bone strains. The study also includes the analysis carried out on standard tibial components with cemented and noncemented stems of the P.F.C Sigma Modular Knee System. The overall agreement within 10% previously established was achieved, indicating that FE models could be successfully validated. The obtained results include a statistical analysis where the root-mean-square-error values were always <10%. FE models can successfully reproduce bone strains under most relevant acting loads upon the condylar surface of the tibia. Moreover, FE models, once properly validated, can be used for preclinical testing of tibial knee replacement, including misalignment of the implants in the proximal tibia after surgery, simulation of long-term failure according to the damage accumulation failure scenario, and other related biomechanical aspects.