Pullout strength of suture anchors: Effect of mechanical properties of trabecular bone

This study investigated the relationships between trabecular microstructure and elastic modulus, compressive strength, and suture anchor pullout strength. Twelve fresh-frozen humeri underwent mechanical testing followed by micro-computed tomography (μCT). Either compression testing of cylindrical bone samples or pullout testing using an Arthrex 5 mm Corkscrew was performed in synthetic sawbone or at specific locations in the humerus such as the greater tuberosity, lesser tuberosity, and humeral head. Synthetic sawbone underwent identical mechanical testing and μCT analysis. Bone volume fraction (BVF), structural model index (SMI), trabecular thickness (TbTh), trabecular spacing (TbSp), trabecular number (TbN), and connectivity density were compared against modulus, compressive strength, and pullout strength in both materials. In cadaveric bone, modulus showed correlations to all of the microstructural properties, while compressive and pullout strength were only correlated to BVF, SMI, and TbSp. The microstructure of synthetic bone differed from cadaveric bone as SMI and TbTh showed little variation across the densities tested. Therefore, SMI and TbTh were the only microstructural properties that did not show correlations to the mechanical properties tested in synthetic bone. This study helps identify key microstructure–property relationships in cadaveric and synthetic bone as well as illustrate the similarities and differences between cadaveric and synthetic bone as biomechanical test materials.     

What humeri are suitable for comparative testing of suture anchors? An ultrastructural bone analysis and biomechanical study of ovine,bovine and human humeri and four different anchor types

For testing of fixation devices such as suture anchors used in rotator cuff repair often animal bones are used. They are easily obtained, inexpensive and some have been found to be similar to human bone. But can we rely on the results drawn from these studies in our daily surgical practice?The purpose of this study was to compare the trabecular bone mineral density, the trabecular bone volume fraction and the cortical layer thickness in the greater tubercle in different species to evaluate their influence on primary stability of suture anchors under a cyclic loading protocol representing the physiologic forces placed on rotator cuff repairs in vivo.Bovine and ovine humeri are not suitable for suture anchor testing. The statistical significances for pullout forces between the anchors varied from species to species. Therefore, no very applicable information can be obtained from testing suture anchors in ovine or bovine humeri with regard to ultimate failure loads in human humeri. The ultimate failure load seems to depend mainly on the cortical thickness and on the subcortical trabecular bone quality.     

A Comparison of Micro-CT and Dental CT in Assessing Cortical Bone Morphology and Trabecular Bone Microarchitecture

Objective

The objective of this study was to evaluate the relationship between the trabecular bone microarchitecture and cortical bone morphology by using micro-computed tomography (micro-CT) and dental cone-beam computed tomography (dental CT).

Materials and Methods

Sixteen femurs and eight fifth lumbar vertebrae were collected from eight male Sprague Dawley rats. Four trabecular bone microarchitecture parameters related to the fifth lumbar vertebral body (percent bone volume [BV/TV], trabecular thickness [TbTh], trabecular separation [TbSp], and trabecular number [TbN]) were calculated using micro-CT. In addition, the volumetric cancellous bone grayscale value (vCanGrayscale) of the fifth lumbar vertebral body was measured using dental CT. Furthermore, four cortical bone morphology parameters of the femoral diaphysis (total cross-sectional area [TtAr], cortical area [CtAr], cortical bone area fraction [CtAr/TtAr], and cortical thickness [CtTh]) were calculated using both micro-CT and dental CT. Pearson analysis was conducted to calculate the correlation coefficients (r) of the micro-CT and dental CT measurements. Paired-sample t tests were used to compare the differences between the measurements of the four cortical bone morphology parameters obtained using micro-CT and dental CT.

Results

High correlations between the vCanGrayscale measured using dental CT and the trabecular bone microarchitecture parameters (BV/TV [r = 0.84] and TbTh [r = 0.84]) measured using micro-CT were observed. The absolute value of the four cortical bone morphology parameters may be different between the dental CT and micro-CT approaches. However, high correlations (r ranged from 0.71 to 0.90) among these four cortical bone morphology parameters measured using the two approaches were obtained.

Conclusion

We observed high correlations between the vCanGrayscale measured using dental CT and the trabecular bone microarchitecture parameters (BV/TV and TbTh) measured using micro-CT, in addition to high correlations between the cortical bone morphology measured using micro-CT and dental CT. Further experiments are necessary to validate the use of dental CT on human bone.     

Predicting the permeability of trabecular bone by micro-computed tomography and finite element modeling

The intrinsic permeability of bone plays an important role in the transport of nutrients and minerals within the tissue, and affects the mechanical stimuli that are related to the fate of the stem cells. The objective of this study was to establish a method to assess trabecular bone permeability using experimental and finite element (FE) modeling approaches based on micro computed tomography (µCT) images. Human cadaveric tibia cube specimens (N=23) were scanned with µCT. The permeability was measured experimentally using a custom-developed constant-head permeameter, and computationally by a poroelastic formulation to simulate the fluid flow within the discretized bone matrix and pore phase. The average of the experimentally measured permeability was 4.84×10⁻¹⁰ m² with a standard deviation of 3.70×10⁻¹⁰ m². A regression model of the µCT determined that the maximum bone area to total area ratio (maxBA/TA) for all slices that are perpendicular to the direction of fluid flow explained 84% of the variability of the natural logarithm of the experimentally measured permeability. The 2D measure of maxBA/TA performed better than 3D measures in general, although some parameters were reasonably well associated with permeability such as bone volume ratio (BV/TV, r=−0.71), the bone surface/bone volume (BS/BV, r=0.73), and the trabecular thickness (TbTh, r=−0.71). The correlation between the permeability predicted with FE models and experimentally measured permeability was reasonable (r=0.69), but the FE approach did not accurately represent the wide variability of permeability measured experimentally. The results of this study suggest that the changes in the trabecular bone microarchitecture have an exponential relationship with permeability, and the use of µCT-based 2D measurement of maxBA/TA performs well at predicting permeability, thus providing a convenient approach to measure this important aspect affecting biomechanical functions in the tissue.     

Quantification of Mineralized Bone Response to Prostate Cancer by Noninvasive In Vivo μCT and Non-Destructive Ex Vivo μCT and DXA in a Mouse Model

Background

To compare nondestructive in vivo and ex vivo micro-computed tomography (μCT) and ex vivo dual-energy-X-ray-absorptiometry (DXA) in characterizing mineralized cortical and trabecular bone response to prostate cancer involving the skeleton in a mouse model.

Methodology/Principal Findings

In vivo μCT was performed before and 10 weeks after implantation of human prostate cancer cells (MDA-PCa-2b) or vehicle into SCID mouse femora. After resection, femora were imaged by nondestructive ex vivo specimen μCT at three voxel sizes (31 µ, 16 µ, 8 µ) and DXA, and then sectioned for histomorphometric analysis of mineralized bone. Bone mineral density (BMD), trabecular parameters (number, TbN; separation, TbSp; thickness, TbTh) and mineralized bone volume/total bone volume (BV/TV) were compared and correlated among imaging methods and histomorphometry. Statistical tests were considered significant if P<0.05. Ten weeks post inoculation, diaphyseal BMD increased in the femur with tumor compared to the opposite femur by all modalities (p<0.005, n = 11). Diaphyseal BMD by in vivo μCT correlated with ex vivo 31 and 16 µm μCT and histomorphometry BV/TV (r = 0.91–0.94, P<0.001, n = 11). DXA BMD correlated less with bone histomorphometry (r = 0.73, P<0.001, n = 11) and DXA did not distinguish trabeculae from cortex. By in vivo and ex vivo μCT, trabecular BMD decreased (P<0.05, n = 11) as opposed to the cortex. Unlike BMD, trabecular morphologic parameters were threshold-dependent and when using “fixed-optimal-thresholds,” all except TbTh demonstrated trabecular loss with tumor and correlated with histomorphometry (r = 0.73–0.90, P<0.05, n = 11).

Conclusions/Significance

Prostate cancer involving the skeleton can elicit a host bone response that differentially affects the cortex compared to trabeculae and that can be quantified noninvasively in vivo and nondestructively ex vivo.     

The assessment of trabecular bone parameters and cortical bone strength: A comparison of micro-CT and dental cone-beam CT

This study compared the capabilities of micro-computed tomography (micro-CT) and dental cone-beam computed tomography (CBCT) in assessing trabecular bone parameters and cortical bone strength. Micro-CT and CBCT scans were applied to 28 femurs from 14 rats to obtain independent measurements of the volumetric cancellous bone mineral density (vCanBMD) in the femoral head, volumetric cortical bone mineral density (vCtBMD) in the femoral diaphysis, cross-sectional moment of inertia (CSMI), and bone strength index (BSI) (=CSMI×vCtBMD). Five structural parameters of the trabecular bone of the femoral head were calculated from micro-CT images. A three-point bending test was then conducted to measure the fracture load of each femur. Bivariate linear Pearson analysis was conducted to calculate the correlation coefficients (r values) of the micro-CT, dental CBCT, and three-point bending measurements. The statistical analyses showed a strong correlation between vCanBMD values obtained using micro-CT and dental CBCT (r=0.830). There were strong or moderate correlation between vCanBMD measured using dental CBCT and five parameters of trabecular structure measured using micro-CT. Additionally, the results were satisfactory regardless of whether micro-CT or dental CBCT was used to measure the femoral diaphysis vCtBMD (r=0.733 and 0.680, respectively), CSMI (r=0.756 and 0.726, respectively), or BSI (r=0.846 and 0.847, respectively) to predict fracture loads. This study has yielded a new method for using dental CBCT to evaluate bone parameters and bone strength; however, further studies are necessary to validate the use of dental CBCT on humans.     

Enhancement of tendon-bone healing with the use of bone morphogenetic protein-2 inserted into the suture anchor hole in a rabbit patellar tendon model

Background aimsSuture anchor fixation failure has been reported as a result of anchor loosening and migration during the tendon-bone repair. The aim of this study was to evaluate the effects of bone morphogenetic protein-2 (BMP-2) inserted into the suture anchor hole on bone formation and the tendon-bone healing.MethodsBoth back legs of 24 New Zealand White rabbits (n = 48) were used in this study. A metal suture anchor was then placed 5 mm below the cortex. In the control group, the space over the eyelet of the anchor (suture anchor hole) was not filled. In the experimental group, the suture anchor hole was filled with 0.1 mL of fibrin glue (group 2) or collagen gel (group 3) with 1 μg BMP-2. Histologic analysis, real-time-polymerase chain reaction, bone density and failure load measurement were performed, and differences were analyzed at 4 and 8 weeks.ResultsHistologic analysis revealed more abundant new bone, mature bone and organized fibrocartilage at the tendon-bone interface at 4 and 8 weeks in groups in which BMP-2 was applied. At 8 weeks, the failure load of groups 1, 2 and 3 was significantly different among the three groups (P = 0.01). After post hoc Tukey test, the failure load of group 2 was significantly higher than that of group 1 (P = 0.01).ConclusionsBMP-2, administrated as described in this study, improved tendon-bone healing and bone formation, resulting in improved biomechanical strength of the tendon-bone junction.     

Cortical Bone Morphological and Trabecular Bone Microarchitectural Changes in the Mandible and Femoral Neck of Ovariectomized Rats

ObjectiveThis study used microcomputed tomography (micro-CT) to evaluate the effects of ovariectomy on the trabecular bone microarchitecture and cortical bone morphology in the femoral neck and mandible of female rats.ResultsRegarding the trabecular bone microarchitectural parameters, the BV/TV of the trabecular bone microarchitecture in the femoral necks of the control group (61.199±11.288%, median ± interquartile range) was significantly greater than that of the ovariectomized group (40.329±5.153%). Similarly, the BV/TV of the trabecular bone microarchitecture in the mandibles of the control group (51.704±6.253%) was significantly greater than that of the ovariectomized group (38.486±9.111%). Furthermore, the TbSp of the femoral necks in the ovariectomized group (0.185±0.066 mm) was significantly greater than that in the control group (0.130±0.026mm). Similarly, the TbSp of the mandibles in the ovariectomized group (0.322±0.047mm) was significantly greater than that in the control group (0.285±0.041mm). However, the TbTh and TbN trends for the mandibles and femoral necks were inconsistent between the control and ovariectomized groups. Regarding the cortical bone morphology parameters, the TtAr of the femoral necks in the ovariectomized group was significantly smaller than that in the control group. There was no significant difference in the TtAr, CtAr, or CtTh of the femoral necks between the control and ovariectomized groups, and no significant difference in the CtTh of the mandibles between the control and ovariectomized groups. Moreover, the BV/TV and TbSp of the mandibles were highly correlated with those of the femurs (r_s = 0.874 and r_s = 0.755 for BV/TV and TbSp, respectively). Nevertheless, the TbTh, TbN, and CtTh of the mandibles were not correlated with those of the femoral necks.ConclusionAfter the rats were ovariectomized, osteoporosis of the trabecular bone microarchitecture occurred in their femurs and mandibles; however, ovariectomy did not influence the cortical bone morphology. In addition, the parametric values of the trabecular bone microarchitecture in the femoral necks were highly correlated with those of the trabecular bone microarchitecture in the mandibles.     

Dependence of mechanical properties of trabecular bone on plate–rod microstructure determined by individual trabecula segmentation (ITS)

Individual trabecula segmentation (ITS) technique can decompose the trabecular bone network into individual trabecular plates and rods and is capable of quantifying the plate/rod-related microstructural characteristics of trabecular bone. This novel technique has been shown to be able to provide in-depth insights into micromechanics and failure mechanisms of human trabecular bone, as well as to distinguish the fracture status independent of area bone mineral density in clinical applications. However, the plate/rod microstructural parameters from ITS have never been correlated to experimentally determined mechanical properties of human trabecular bone. In this study, on-axis cylindrical trabecular bone samples from human proximal tibia (n=22), vertebral body (n=10), and proximal femur (n=21) were harvested, prepared, scanned using micro computed-tomography (µCT), analyzed with ITS and mechanically tested. Regression analyses showed that the plate bone volume fraction (pBV/TV) and axial bone volume fraction (aBV/TV) calculated by ITS analysis correlated the best with elastic modulus (R²=0.96–0.97) and yield strength (R²=0.95–0.96). Trabecular plate-related microstructural parameters correlated highly with elastic modulus and yield strength, while most rod-related parameters were found inversely and only moderately correlated with the mechanical properties. In addition, ITS analysis also identified that trabecular bone at human femoral neck had the highest trabecular plate-related parameters while the other sites were similar with each other in terms of plate–rod microstructure.     

Bone microarchitecture in ankylosing spondylitis and the association with bone mineral density,fractures, and syndesmophytes

Introduction

Osteoporosis of the axial skeleton is a known complication of ankylosing spondylitis (AS), but bone loss affecting the peripheral skeleton is less studied. This study on volumetric bone mineral density (vBMD) and bone microarchitecture in AS was conducted to compare peripheral vBMD in AS patients with that in healthy controls, to study vBMD in axial compared with peripheral bone, and to explore the relation between vertebral fractures, spinal osteoproliferation, and peripheral bone microarchitecture and density.

Methods

High-resolution peripheral quantitative computed tomography (HRpQCT) of ultradistal radius and tibia and QCT and dual-energy x-ray absorptiometry (DXA) of lumbar spine were performed in 69 male AS patients (NY criteria). Spinal radiographs were assessed for vertebral fractures and syndesmophyte formation (mSASSS). The HRpQCT measurements were compared with the measurements of healthy controls.

Results

The AS patients had lower cortical vBMD in radius (P = 0.004) and lower trabecular vBMD in tibia (P = 0.033), than did the controls. Strong correlations were found between trabecular vBMD in lumbar spine, radius (r_S = 0.762; P < 0.001), and tibia (r_S = 0.712; P < 0.001).When compared with age-matched AS controls, patients with vertebral fractures had lower lumbar cortical vBMD (-22%; P = 0.019), lower cortical cross-sectional area in radius (-28.3%; P = 0.001) and tibia (-24.0%; P = 0.013), and thinner cortical bone in radius (-28.3%; P = 0.001) and tibia (-26.9%; P = 0.016).mSASSS correlated negatively with trabecular vBMD in lumbar spine (r_S = -0.620; P < 0.001), radius (r_S = -0.400; p = 0.001) and tibia (r_S = -0.475; p < 0.001) and also with trabecular thickness in radius (r_S = -0.528; P < 0.001) and tibia (r_S = -0.488; P < 0.001).Adjusted for age, syndesmophytes were significantly associated with decreasing trabecular vBMD, but increasing cortical vBMD in lumbar spine, but not with increasing cortical thickness or density in peripheral bone. Estimated lumbar vBMD by DXA correlated with trabecular vBMD measured by QCT (r_S = 0.636; P < 0.001).

Conclusions

Lumbar osteoporosis, syndesmophytes, and vertebral fractures were associated with both lower vBMD and deteriorated microarchitecture in peripheral bone. The results indicate that trabecular bone loss is general, whereas osteoproliferation is local in AS.     

Phenotypic Dissection of Bone Mineral Density Reveals Skeletal Site Specificity and Facilitates the Identification of Novel Loci in the Genetic Regulation of Bone Mass Attainment

Heritability of bone mineral density (BMD) varies across skeletal sites, reflecting different relative contributions of genetic and environmental influences. To quantify the degree to which common genetic variants tag and environmental factors influence BMD, at different sites, we estimated the genetic (r_g) and residual (r_e) correlations between BMD measured at the upper limbs (UL-BMD), lower limbs (LL-BMD) and skull (SK-BMD), using total-body DXA scans of ∼4,890 participants recruited by the Avon Longitudinal Study of Parents and their Children (ALSPAC). Point estimates of r_g indicated that appendicular sites have a greater proportion of shared genetic architecture (LL-/UL-BMD r_g = 0.78) between them, than with the skull (UL-/SK-BMD r_g = 0.58 and LL-/SK-BMD r_g = 0.43). Likewise, the residual correlation between BMD at appendicular sites (r_e = 0.55) was higher than the residual correlation between SK-BMD and BMD at appendicular sites (r_e = 0.20–0.24). To explore the basis for the observed differences in r_g and r_e, genome-wide association meta-analyses were performed (n∼9,395), combining data from ALSPAC and the Generation R Study identifying 15 independent signals from 13 loci associated at genome-wide significant level across different skeletal regions. Results suggested that previously identified BMD-associated variants may exert site-specific effects (i.e. differ in the strength of their association and magnitude of effect across different skeletal sites). In particular, variants at CPED1 exerted a larger influence on SK-BMD and UL-BMD when compared to LL-BMD (P = 2.01×10⁻³⁷), whilst variants at WNT16 influenced UL-BMD to a greater degree when compared to SK- and LL-BMD (P = 2.31×10⁻¹⁴). In addition, we report a novel association between RIN3 (previously associated with Paget''s disease) and LL-BMD (rs754388: β = 0.13, SE = 0.02, P = 1.4×10⁻¹⁰). Our results suggest that BMD at different skeletal sites is under a mixture of shared and specific genetic and environmental influences. Allowing for these differences by performing genome-wide association at different skeletal sites may help uncover new genetic influences on BMD.     

Contribution to FE modeling for intraoperative pedicle screw strength prediction

Although the use of pedicle screws is considered safe, mechanical issues still often occur. Commonly reported issues are screw loosening, screw bending and screw fracture. The aim of this study was to develop a Finite Element (FE) model for the study of pedicle screw biomechanics and for the prediction of the intraoperative pullout strength. The model includes both a parameterized screw model and a patient-specific vertebra model. Pullout experiments were performed on 30 human cadaveric vertebrae from ten donors. The experimental force-displacement data served to evaluate the FE model performance. μCT images were taken before and after screw insertion, allowing the creation of an accurate 3D-model and a precise representation of the mechanical properties of the bone. The experimental results revealed a significant positive correlation between bone mineral density (BMD) and pullout strength (Spearman ρ = 0.59, p < 0.001) as well as between BMD and pullout stiffness (Spearman ρ = 0.59, p < 0.001). A high positive correlation was also found between the pullout strength and stiffness (Spearman ρ = 0.84, p < 0.0001). The FE model was able to reproduce the linear part of the experimental force-displacement curve. Moreover, a high positive correlation was found between numerical and experimental pullout stiffness (Pearson ρ = 0.96, p < 0.005) and strength (Pearson ρ = 0.90, p < 0.05). Once fully validated, this model opens the way for a detailed study of pedicle screw biomechanics and for future adjustments of the screw design.     

Local irradiation alters bone morphology and increases bone fragility in a mouse model

Insufficiency fracture following radiation therapy (RTx) is a challenging clinical problem and typical bone mass measures fail to predict these fractures. The goals of this research were to develop a mouse model that results in reduced bone strength following focal irradiation, quantify morphological and strength changes occurring over time, and determine if a positive correlation between bone morphology and strength is retained after irradiation. Right hind limbs of 13 week-old female Balb/c mice were irradiated (5 or 20 Gy) using a therapeutic X-ray unit. Left limbs served as control. Animals were euthanized at 2, 6, 12, or 26 weeks. Axial compression tests of the distal femur were used to quantify whole bone strength. Specimen-specific, non-linear finite element (FE) analyses of the mechanical tests were performed using voxel-based meshes with two different material failure models: a linear bone density–strength relationship and a non-linear ‘embrittled’ relationship. Radiation resulted in a dose dependent increase in cortical bone density and marked loss of trabecular bone, measured using micro-CT. An early (2 week) increase in bone volume was associated with an increase in bone strength following irradiation; at 12 weeks there was a loss of bone strength despite higher bone volume for irradiated limbs. There was a positive correlation between bone volume bone and strength in control (r²=0.63) but not irradiated femora (r²=0.08). FE analysis with a constant strain failure model resulted in improved prediction of bone strength for irradiated limbs (r²=0.34) and this was improved further with the embrittled material model (r²=0.46). In summary, focal irradiation leads to substantial changes in bone morphology and strength with time, where there is a decreased bone strength following irradiation in the face of increasing bone mass; FE models with a non-linear embrittled material model were most successful in simulating these experimental findings.     

Distal skeletal tibia assessed by HR-pQCT is highly correlated with femoral and lumbar vertebra failure loads

Dual energy X-ray absorptiometry (DXA) is the standard for assessing fragility fracture risk using areal bone mineral density (aBMD), but only explains 60–70% of the variation in bone strength. High-resolution peripheral quantitative computed tomography (HR-pQCT) provides 3D-measures of bone microarchitecture and volumetric bone mineral density (vBMD), but only at the wrist and ankle. Finite element (FE) models can estimate bone strength with 86–95% precision. The purpose of this study is to determine how well vBMD and FE bone strength at the wrist and ankle relate to fracture strength at the hip and spine, and to compare these relationships with DXA measured directly at those axial sites. Cadaveric samples (radius, tibia, femur and L4 vertebra) were compared within the same body. The radius and tibia specimens were assessed using HR-pQCT to determine vBMD and FE failure load. aBMD from DXA was measured at the femur and L4 vertebra. The femur and L4 vertebra specimens were biomechanically tested to determine failure load. aBMD measures of the axial skeletal sites strongly correlated with the biomechanical strength for the L4 vertebra (r = 0.77) and proximal femur (r = 0.89). The radius correlated significantly with biomechanical strength of the L4 vertebra for vBMD (r = 0.85) and FE-derived strength (r = 0.72), but not with femur strength. vBMD at the tibia correlated significantly with femoral biomechanical strength (r = 0.74) and FE-estimated strength (r = 0.83), and vertebral biomechanical strength for vBMD (r = 0.97) and FE-estimated strength (r = 0.91). The higher correlations at the tibia compared to radius are likely due to the tibia’s weight-bearing function.     

Volume to density relation in adult human bone tissue

Uniformity of tissue mineralisation is a strongly debated issue, due to its relation with bone mechanical behaviour. Bone mineral density (BMD) is measured in the clinical practice and is applied in computational application to derive material proprieties of bone tissue. However, BMD cannot identify if the variation in bone density is related to a modification of tissue mineral density (TMD), a change in bone volume or a combination of the two. This study was aimed to investigate whether TMD can be assumed as a constant in adult human bone (trabecular and cortical).A total number of 115 cylindrical bone specimens were collected. An inter-site analysis (96 specimens, 2 donors) was performed on cortical and trabecular specimens extracted from different anatomical sites. An intra-site study (19 specimens, 19 donors) was performed on specimens extracted from femoral heads. Bone volume fraction (BV/TV) was computed by means of a micro-computed tomography. Furthermore, ash density (ρ_ash) was measured. TMD was computed as the ratio between ρ_ash and BV/TV.It was found that the TMD of trabecular (1.24±0.16 g/cm³) and cortical (1.19±0.06 g/cm³) bone were not statistically different (p=0.31). Furthermore, the linear regression between ρ_ash and BV/TV was statistically significant (r²=0.99, p<0.001). Intra- and inter-site analyses demonstrated that the mineral distribution was independent of the extraction site.The present study suggests that TMD can be assumed reasonably constant in non-pathological adult bone tissue. Consequently, it is suggested that TMD can be managed as a constant in computational models, varying only BV in relation to clinical densitometric analysis.     

Predicting surface strains at the human distal radius during an in vivo loading task — Finite element model validation and application

Bone strains resulting from physical activity are thought to be a primary driver of bone adaptation, but cannot be directly noninvasively measured. Because bone adapts nonuniformly, physical activity may make an important independent structural contribution to bone strength that is independent of bone mass and density. Our objective was to create and validate methods for subject-specific finite element (FE) model generation that would accurately predict the surface strains experienced by the distal radius during an in vivo loading task, and to apply these methods to a group of 23 women aged 23–35 to examine variations in strain, bone mass and density, and physical activity. Four cadaveric specimens were experimentally tested and specimen-specific FE models were developed to accurately predict periosteal surface strains (root mean square error=16.3%). In the living subjects, when 300 N load was simulated, mean strains were significantly inversely correlated with BMC (r=−0.893), BMD (r=−0.892) and physical activity level (r=−0.470). Although the group of subjects was relatively homogenous, BMD varied by two-fold (range: 0.19–0.40 g/cm³) and mean energy-equivalent strain varied by almost six-fold (range: 226.79–1328.41 με) with a simulated 300 N load. In summary, we have validated methods for estimating surface strains in the distal radius that occur while leaning onto the palm of the hand. In our subjects, strain varied widely across individuals, and was inversely related to bone parameters that can be measured using clinical CT, and inversely related to physical activity history.     

Analysis of correlation between blood biochemical indicators and bone mineral density of post-menopausal women

Osteoporosis is a degenerative disease of the skeletal system, and its major complication is fracture that severely influences the living quality of the middle-aged and the aged. The purpose of this study was to investigate the significance of sex hormones and some biochemical indicators related to bone metabolism in the genesis and development of osteoporosis. The plasma samples were collected from 244 post-menopausal women of Xi’an urban area, and their plasma contents of testosterone, estradiol, calcitonin, osteocalcin and N-terminal propeptide of type I procollagen were detected by ELISA. The activity of tartrate-resistant acid phosphatase was determined by spectrophotometric method, and the content of nitric oxide was measured by Griess method. Bone mineral density (BMD) in lumbar vertebrae (L1–L4) and hips was measured by QDR-2000 dual energy X-ray absorptiometry. The concentrations of the biochemical indicators were compared among the three groups (normal bone mass group, osteopenia group and osteoporosis group), and Pearson correlation analysis was used to verify the correlations between the indicators and BMD. The comparison results of blood biochemical indicators of BMD-based groups showed that the plasma contents of estradiol (P = 0.006), testosterone (P = 0.038) and calcitonin (P = 0.042) decreased more significantly in the osteoporosis group, but the content of osteocalcin (P = 0.008) increased significantly in osteoporosis group than those in the other groups. The correlation analysis between BMD of different parts and the blood biochemical indicators showed that there was a significant positive correlation between estradiol and the BMD of lumber vertebra (r = 0.200, P = 0.002), femoral neck (r = 0.160, P = 0.013), and great trochanter (r = 0.204, P = 0.001). Significant positive correlations between calcitonin and BMD of lumber vertebra (r = 0.166, P = 0.018) and femoral great trochanter (r = 0.152, P = 0.041), and between testosterone and BMD of femoral great trochanter (r = 0.158, P = 0.014) were also observed. In addition, there existed significant negative correlations between osteocalcin and BMD of lumber vertebra (r = −0.220, P = 0.001), femoral neck (r = −0.259, P < 0.000), and great trochanter (r = −0.221, P = 0.001), and between the activity of tartrate-resistant acid phosphatase and BMD of femoral great trochanter (r = −0.135, P = 0.037). The partial correlation analysis also showed that there were significant correlations between estradiol (r = 0.160, P = 0.014), calcitonin (r = 0.240, P = 0.013), osteocalcin (r = −0.226, P = 0.023) and BMD when the influence of age was excluded. The Pearson correlation analysis of biochemical indicators showed there were positive correlations between the contents of testosterone and calcitonin, testosterone and osteocalcin, calcitonin and osteocalcin, calcitonin and PINP, calcitonin and NO, osteocalcin and NO, and PINP and NO, but negative correlations between the contents of testosterone and PINP, estradiol and calcitonin, estradiol and osteocalcin, and estradiol and NO. The blood contents of sex hormones and calcitonin significantly influence BMD and osteoporosis development, and the increase of osteocalcin contents could be used as a biomarker to indicate the degree of osteoporosis in post-menopausal women.     

A Comparison of Bone Mineral Density and Its Predictors in HIV-Infected and HIV-Uninfected Older Men

ObjectiveBone health in older individuals with HIV infection has not been well studied. This study aimed to compare bone mineral density (BMD), trabecular bone score (TBS), and bone markers between HIV-infected men and age- and body mass index (BMI)-matched HIV-uninfected men aged ≥60 years. We investigated the associations of risk factors related to fracture with BMD, TBS, and bone markers in HIV-infected men.MethodsThis cross-sectional study included 45 HIV-infected men receiving antiretroviral therapy and 42 HIV-uninfected men. Medical history, BMD and TBS measurements, and laboratory tests related to bone health were assessed in all the participants. HIV-related factors known to be associated with bone loss were assessed in the HIV-infected men.ResultsThe mean BMD, TBS, and osteopenia or osteoporosis prevalence were similar among the cases and controls. The HIV-infected men had significantly higher mean N-terminal propeptide of type 1 procollagen and C-terminal cross-linking telopeptide of type I collagen levels. Stepwise multiple linear regression analysis demonstrated that low BMI (lumbar spine, P = .015; femoral neck, P = .018; and total hip, P = .005), high C-terminal cross-linking telopeptide of type I collagen concentration (total hip, P = .042; and TBS, P = .010), and low vitamin D supplementation (TBS, P = .035) were independently associated with low BMD and TBS.ConclusionIn older HIV-infected men with a low fracture risk, the mean BMD and TBS were similar to those of the age- and BMI-matched controls. The mean bone marker levels were higher in the HIV group. Traditional risk factors for fracture, including low BMI, high C-terminal cross-linking telopeptide of type I collagen level, and low vitamin D supplementation, were significant predictors of low BMD and TBS.     

Interrelationship of trabecular mechanical and microstructural properties in sheep trabecular bone

The ability to evaluate fracture risk at an early time point is essential for improved prognostics as well as enhanced treatment in cases of bone loss such as from osteoporosis. Improving the diagnostic ability is inherent upon both high-resolution non-invasive imaging, and a thorough understanding of how the derived indices of structure and density relate to its true mechanical behavior. Using sheep femoral trabecular bone with a range of strength, the interrelationship of mechanical and microstructural parameters was analyzed using multi-directional mechanical testing and micro-computed tomography. Forty-five cubic trabecular bone samples were harvested from 23 adult female sheep, some of whom had received hind-limb vibratory stimuli over the course of 2 years with consequently enhanced mechanical properties. These samples were pooled into a low, medium, or high strength group for further analysis. The findings show that microCT indices that are structural in nature, e.g., structural model index (SMI) (r2=0.85, p<0.0001) is as good as more density oriented indices like bone volume/total volume (BV/TV) (r2=0.81, p<0.0001) in predicting the ultimate strength of a region of trabecular bone. Additionally, those indices more related to global changes in trabecular structure such as connectivity density (ConnD) or degree of anisotropy (DA) are less able to predict the mechanical properties of bone. Interrelationships of trabecular indices such as trabecular number (TbN), thickness (TbTh), and spacing (TbSp) provide clues as to how the trabecular bone will remodel to ultimately achieve differences in the apparent mechanical properties. For instance, the analysis showed that a loss of bone primarily affects the connectedness and overall number of trabeculae, while increased strength results in an increase of the overall thickness of trabeculae while not improving the connectedness. Certainly, the microCT indices studied are able to predict the bulk mechanical properties of a trabecular ROI well, leaving unaccounted only about 15-20% of its inherent variability. Diagnostically, this implies that future work on the early prediction of fracture risk should continue to explore the role of bone quality as the key factors or as an adjuvant to bone quantity (e.g., apparent density).     

Micromechanical analyses of vertebral trabecular bone based on individual trabeculae segmentation of plates and rods

Trabecular plates play an important role in determining elastic moduli of trabecular bone. However, the relative contribution of trabecular plates and rods to strength behavior is still not clear. In this study, individual trabeculae segmentation (ITS) and nonlinear finite element (FE) analyses were used to evaluate the roles of trabecular types and orientations in the failure initiation and progression in human vertebral trabecular bone. Fifteen human vertebral trabecular bone samples were imaged using micro computed tomography (μCT), and segmented using ITS into individual plates and rods by orientation (longitudinal, oblique, and transverse). Nonlinear FE analysis was conducted to perform a compression simulation for each sample up to 1% apparent strain. The apparent and relative trabecular number and tissue fraction of failed trabecular plates and rods were recorded during loading and data were stratified by trabecular orientation. More trabecular rods (both in number and tissue fraction) failed at the initiation of compression (0.1–0.2% apparent strain) while more plates failed around the apparent yield point (>0.7% apparent strain). A significant correlation between plate bone volume fraction (pBV/TV) and apparent yield strength was found (r²=0.85). From 0.3% to 1% apparent strain, significantly more longitudinal trabecular plate and transverse rod failed than other types of trabeculae. While failure initiates at rods and rods fail disproportionally to their number, plates contribute significantly to the apparent yield strength because of their larger number and tissue volume. The relative failed number and tissue fraction at apparent yield point indicate homogeneous local failure in plates and rods of different orientations.