A capillary electrophoresis-based enzyme assay for kinetics and inhibition studies of carbonic anhydrase

In the current study, capillary electrophoresis (CE)-based enzyme assay for characterization and inhibition study of bovine carbonic anhydrase II (bCA II) was developed. The developed method is the first CE assay for carbonic anhydrase (CA). The method was optimized in order to get short analysis time, minimal sample volume consumption, and high resolution of substrate and product. The CE conditions were optimized as follows: fused-silica capillary (30 cm effective length × 75 μm i.d.), pressure injection for 5 s, 20 mM sodium borate buffer (pH 9.0), constant voltage of 15 kV, constant capillary temperature of 25 °C, and detection at 260 nm. For precise measurements, uridine was used as an internal standard during optimization of the CE methods. The limits of detection and quantification for p-nitrophenyl acetate (p-NPA) were 3.01 and 9.12 μM, respectively, whereas for p-nitrophenolate they were 2.05 and 6.22 μM, respectively. The performance of the developed method was confirmed by determination of kinetic parameters (i.e., K_m and V_max of bCA for p-NPA); the inhibition constant (K_i) was determined for furosemide, a standard inhibitor of CA. The new method proved to be fast and efficient, and it can be used for the investigation of inhibitors of all isoforms of CAs.     

Capillary electrophoresis-based assay of phosphofructokinase-1

An assay was developed for phosphofructokinase-1 (PFK-1) using capillary electrophoresis (CE). In the glycolytic pathway, this enzyme catalyzes the rate-limiting step from fructose-6-phosphate and magnesium-bound adenosine triphosphate (Mg–ATP) to fructose-1,6-bisphosphate and magnesium-bound adenosine diphosphate (Mg–ADP). This enzyme has recently become a research target because of the importance of glycolysis in cancer and obesity. The CE assay for PFK-1 is based on the separation and detection by ultraviolet (UV) absorbance at 260 nm of Mg–ATP and Mg–ADP. The separation was enhanced by the addition of Mg²⁺ to the separation buffer. Inhibition studies of PFK-1 by aurintricarboxylic acid and palmitoyl coenzyme A were also performed. An IC₅₀ value was determined for aurintricarboxylic acid, and this value matched values in the literature obtained using coupled spectrophotometric assays. This assay for PFK-1 directly monitors the enzyme-catalyzed reaction, and the CE separation reduces the potential of spectral interference by inhibitors.     

Quantitative, small-scale, fluorophore-assisted carbohydrate electrophoresis implemented on a capillary electrophoresis-based DNA sequence analyzer

Fluorophore-assisted carbohydrate electrophoresis (FACE) is an analytical method for characterizing carbohydrate chain length that has been applied to neutral, charged, and N-linked oligosaccharides and that has been implemented using diverse separation platforms, including polyacrylamide gel electrophoresis and capillary electrophoresis. In this article, we describe three substantial improvements to FACE: (i) reducing the amount of starch and APTS required in labeling reactions and systematically analyzing the effect of altering the starch and 8-amino-1,3,6-pyrenetrisulfonic acid (APTS) concentrations on the reproducibility of the FACE peak area distributions; (ii) implementing FACE on a multiple capillary DNA sequencer (an ABI 3130xl), enabling higher throughput than is possible on other separation platforms; and (iii) developing a protocol for producing quantitative output of peak heights and areas using genetic marker analysis software. The results of a designed experiment to determine the effect of decreasing both the starch and fluorophore concentrations on the sensitivity and reproducibility of FACE electrophoregrams are presented. Analysis of the peak area distributions of the FACE electrophoregrams identified the labeling reaction conditions that resulted in the smallest variances in the peak area distributions while retaining strong fluorescence signals from the capillary-based DNA sequencer.     

A capillary electrophoresis assay for recombinant Bacillus subtilis protoporphyrinogen oxidase

Protoporphyrinogen oxidase (PPO) is a flavin adenine dinucleotide (FAD)-containing enzyme in the tetrapyrrole biosynthetic pathway that leads to the formation of both heme and chlorophylls, which has been identified as one of the most important action targets of commercial herbicides. The literature reports gave different PPO-catalytic kinetic parameters for the substrate protoporphyrinogen IX (K_m of 0.1 to 10.4 μM) with different sources of PPO using fluorescent or HPLC methods. Herein we assayed the enzymatic activity of recombinant Bacillus subtilis PPO by using capillary electrophoresis (CE), a method with high separation efficiency, easy automation, and low sample consumption. The Michaelis constant and maximum reaction velocity were determined as 7.0 ± 0.6 μM and 0.38 ± 0.02 μmol min^-1 μg⁻¹, respectively. The interaction between PPO and acifluorfen, a commercial PPO-inhibiting herbicide, was measured as the inhibition constant 186.9 ± 9.3 μМ. The relationship between cofactor FAD and PPO activity can also be quantitatively studied by this CE method. The CE method used here should also be a convenient, reliable method for PPO study.     

Capillary electrophoresis-mass spectrometry as a characterization tool for therapeutic proteins

With the increasing use of capillary electrophoresis (CE) in the biotechnology industry, there is a demand for analytical tools and methodology that can be used to characterize CE profiles. This article describes the implementation and optimization of a robust online CE-mass spectrometry (CE-MS) system used for the characterization of several CE assays developed at Genentech Inc. These assays include CE as a complement to reverse-phase peptide mapping for the identification of small peptides eluting in the void volume, profiling N-linked glycopeptide heterogeneity, and determining O-linked site occupancy. In addition, CE-MS was used to confirm major 8-aminopyrene-1,3,6-trisulfonate (APTS)-labeled glycans released from recombinant antibodies that are routinely profiled by CE-laser-induced fluorescence (CE-LIF). For each study, CE-MS was able to successfully identify components seen in UV or LIF electropherograms, thereby expanding the capability of CE and CE-MS for profiling biomolecules.     

A general assay for restriction endonucleases and other DNA-modifying enzymes with plasmid substrates

A procedure for measuring the activities of enzymes that alter the covalent structure of DNA is described. The assay utilizes covalently closed circles of DNA as the substrate and yields quantitative data on the fraction of this DNA converted to both open-circle and linear forms.     

Synthetic peptides as substrates for processing enzymes in the bovine pituitary

Synthetic peptides, based on sequences of proopiomelanocortin (POMC) cleaved in both the bovine anterior and intermediate pituitaries (-Phe-Pro-Leu-Gly-Phe-Lys-Arg-Glu-Leu-Thr-Gly-) and only in the intermediate lobe (-Gly-Lys-Pro-Val-Gly-Lys-Lys-Arg-Arg-Pro-Val-), were used as substrates for the enzymes that process POMC to active hormones in the anterior and intermediate lobes of the pituitary. Cleavage of these peptides at the dibasic pair of residues, the expected cleavage site, was observed with a lysate from bovine pituitary secretory granules. Cleavage occurred optimally at a pH between 4 and 5 and was inhibited with sulfhydryl reagents, pepstatin, and leupeptin. Little specificity for the nature of the basic residues at the cleavage site was observed. An additional cleavage, following glutamic acid residues, was also seen.     

A modified capillary assay for chemotaxis

Summary A modification is described of the capillary assay for chemotaxis. It employs a 96-well dilution plate and its cover. Capillary tubes are inserted through the cover and are supported by small rubber collars. The method is faster and less tedious and gives more precise results than earlier methods.     

On-line multidimensional liquid chromatography and capillary electrophoresis systems for peptides and proteins

Peptides and proteins are gaining increasing attention in biosciences and, consequently, in analysis. This overview highlights the different approaches to couple on-line various separation techniques for the determination of proteins and peptides. The first section discusses the liquid chromatography (LC)-LC coupling, the second one reviews the on-line LC-capillary electrophoresis (CE) coupled systems and the third section summarizes the strategies for on-line CE-CE. The advantages, disadvantages, most relevant difficulties and particular systems for on-line coupling are discussed. Special attention is paid to the interface between the two dimensions. Applications are summarized in tables and a few typical examples are discussed. Many multidimensional separation methods are available, and it is demonstrated that peptide and protein mapping, or quantitation of proteins or peptides in various samples (aqueous solutions, cells, plasma) require different coupled systems. For mapping a semi-quantitative detection is often sufficient, while comprehensiveness is very important. For quantitation of a certain peptide or protein at a low concentration level a validated method should be used, while a heart-cut transport of the first dimension to the second one can offer sufficient selectivity. The combination with mass spectrometry as part of the total system is stressed and illustrated.     

On-line combination of capillary isoelectric focusing and capillary non-gel sieving electrophoresis using a hollow-fiber membrane interface: a novel two-dimensional separation system for proteins

A novel two-dimensional (2D) separation system for proteins was reported. In the system, a piece of dialysis hollow-fiber membrane was employed as the interface for on-line combination of capillary isoelectric focusing (CIEF) and capillary non-gel sieving electrophoresis (CNGSE). The system is similar equivalent to two-dimensional polyacrylamide gel electrophoresis (2D PAGE), by transferring the principal of 2D PAGE separation to the capillary format. Proteins were focused and separated in first dimension CIEF based on their differences in isoelectric points (pIs). Focused protein zones was transferred to the dialysis hollow-fiber interface, where proteins hydrophobically complexed with sodium dodecyl sulfate (SDS). The negatively charged proteins were electromigrated and further resolved by their differences in size in the second dimension CNGSE, in which dextran solution, a replaceable sieving matrix instead of cross-linked polyacrylamide gel was employed for size-dependent separation of proteins. The combination of the two techniques was attributed to high efficiency of the dialysis membrane interface. The feasibility and the orthogonality of the combined CIEF-CNGSE separation technique, an important factor for maximizing peak capacity or resolution elements, were demonstrated by examining each technique independently for the separation of hemoglobin and protein mixtures excreting from lung cancer cells of rat. The 2D separation strategy was found to greatly increase the resolving power and overall peak capacity over those obtained for either dimension alone.     

Validation of methyl malondialdehyde as internal standard for malondialdehyde detection by capillary electrophoresis

The aim of this study was to validate, by capillary electrophoresis, the use of synthesized methyl malondialdehyde as the internal standard for the direct quantification of free and total (free+bound) malondialdehyde in biological samples. All analyses were performed in 20 cm x 50 microm uncoated capillaries at 20 degrees C, using 25 mmol/L borax (pH 9.3) and 5 mmol/L tetradecyltrimethylammonium bromide as running buffer. The applied voltage was -4kV (about 8 microA), the detector being set at 260 nm for a total run time of 8 min per sample. Free malondialdehyde was evaluated after acetonitrile extraction, while the samples evaluated for total malondialdehyde were, before extraction, hydrolyzed for 1h at 60 degrees C in the presence of 1 mol/L NaOH. The detection threshold was 0.2 micromol/L in microsomes and 0.4 micromol/L in plasma. As an application of the method, three pools of rat liver microsomes were quantified before (0.35+/-0.1 and 1.1+/-0.5 nmol/mg protein, free and total malondialdehyde, respectively, mean+/-SD) and after lipoperoxidation induction using systems able to generate oxygen free radicals (18.4+/-3.2 and 19.7+/-2.0 nmol/mg protein). The results were confirmed by isotopic dilution gas chromatography-mass spectrometry, used as the reference method. The feasibility of capillary electrophoresis for malondialdehyde determination in normal and pathological human plasma was also investigated.     

A capillary electrophoresis method to assay catalytic activity of botulinum neurotoxin serotypes: implications for substrate specificity

The potent botulinum neurotoxin inhibits neurotransmitter release at cholinergic nerve terminals, causing a descending flaccid paralysis characteristic of the disease botulism. The currently expanding medical use of the neurotoxin to treat several disorders, as well as the potential misuse of the neurotoxin as an agent in biowarfare, has made understanding of the nature of the toxin's catalytic activity and development of inhibitors critical. To study the catalytic activity of botulinum neurotoxin more thoroughly and characterize potential inhibitors, we have developed a capillary electrophoresis method to measure catalytic activity of different serotypes of botulinum neurotoxin using peptides derived from the native substrates. This assay requires only a minute amount of sample (25 nl), is relatively rapid (15 min/sample), and allows the determination of enzyme kinetic constants for a more sophisticated characterization of inhibitors and neurotoxin catalytic activity. Using this method, we can measure activity of five of the seven serotypes of botulinum neurotoxin (A, B, E, F, and G) with two peptide substrates. Botulinum neurotoxin serotypes C and D did not cleave our peptides, lending insight into potential substrate requirements among the serotypes.     

Quantitative capillary electrophoresis determination of oversulfated chondroitin sulfate as a contaminant in heparin preparations

A simple, accurate, and robust quantitative capillary electrophoresis (CE) method for the determination of oversulfated chondroitin sulfate (OSCS) as a contaminant in heparin (Hep) preparations is described. After degradation of the polysaccharides by acidic hydrolysis, the hexosamines produced (i.e., GlcN from Hep and GalN from OSCS) were derivatized with anthranilic acid (AA) and separated by means of CE in approximately 10 min with high sensitivity detection at 214 nm (limit of detection [LOD] of ∼200 pg). Furthermore, AA-derivatized GlcN and GalN showed quite similar molar absorptivity, allowing direct and simple quantification of OSCS in Hep samples. Moreover, a preliminary step of specific enzymatic treatment by using chondroitin ABC lyase may be applied for the specific elimination of interference in the analysis due to the possible presence in Hep samples of natural chondroitin sulfate and dermatan sulfate impurities, making this analytical approach highly specific for OSCS contamination given that chondroitin ABC lyase is unable to act on this semisynthetic polymer. The CE method was validated for specificity, linearity, accuracy, precision, LOD, and limit of quantification (LOQ). Due to the very high sensitivity of CE, as little as 1% OSCS contaminant in Hep sample could be detected and quantified. Finally, a contaminated raw Hep sample was found to contain 38.9% OSCS, whereas a formulated contaminated Hep was calculated to have 39.7% OSCS.     

Graphene quantum dots as additives in capillary electrophoresis for separation cinnamic acid and its derivatives

A facile capillary electrophoresis (CE) method for the separation of cinnamic acid and its derivatives (3,4-dimethoxycinnamic acid, 4-methoxycinnamic acid, isoferulic acid, sinapic acid, cinnamic acid, ferulic acid, and trans-4-hydroxycinnamic acid) using graphene quantum dots (GQDs) as additives with direct ultraviolet (UV) detection is reported. GQDs were synthesized by chemical oxidization and further purified by a macroporous resin column to remove salts (Na₂SO₄ and NaNO₃) and other impurities. Transmission electron microscopy (TEM) indicated that GQDs have a relatively uniform particle size (2.3 nm). Taking into account the structural features of GQDs, cinnamic acid and its derivatives were adopted as model compounds to investigate whether GQDs can be used to improve CE separations. The separation performance of GQDs used as additives in CE was studied through variations of pH, concentration of the background electrolyte (BGE), and contents of GQDs. The results indicated that excellent separation can be achieved in less than 18 min, which is mainly attributed to the interaction between the analytes and GQDs, especially isoferulic acid, sinapic acid, and cinnamic acid.     

Internally quenched fluorogenic protease substrates: Solid-phase synthesis and fluorescence spectroscopy of peptides containing ortho-aminobenzoyl/dinitrophenyl groups as donor-acceptor pairs

Summary A general procedure, using the commonly employed solid-phase peptide synthesis methodology for obtaining internally quenched fluorogenic peptides with ortho-aminobenzoyl/dinitrophenyl groups as donor-acceptor pairs, is presented. The essential feature of this procedure is the synthesis of an N -Boc or-Fmoc derivative of glutamic acid with the -carboxyl group bound to N-(2,4-dinitrophenyl)-ethylenediamine (EDDnp), which provides the quencher moiety attached to the C-terminus of the substrate. The fluorescent donor group, ortho-aminobenzoic acid (Abz), is incorporated into the resin-bound peptide in the last coupling cycle. Depending on the resin type used, Abz-peptidyl-Gln-EDDnp or Abz-peptidyl-Glu-EDDnp is obtained. Using the procedure described above, substrates for human renin and tissue kallikreins were synthesised. Spectrofluorimetric measurements of Abz bound to the -amino group of proline showed that strong quenching of Abz fluorescence occurs in the absence of any acceptor group.     

Enantioseparation using cyclosophoraoses as a novel chiral additive in capillary electrophoresis

Cyclosophoraoses, cyclic beta-(1-->2)-D-glucans produced by Rhizobium meliloti 2011, were used as a novel chiral additive for the separation of terbutaline, amethopterin, thyroxine and N-acetylphenylalanine enantiomers in aqueous capillary electrophoresis (CE). Enantioseparation took place in the normal- or reversed-polarity mode when a high concentration of neutral (60 mM) or anionic (40 mM) cyclosophoraoses was added to the background electrolyte (BGE).     

On-line melting of double-stranded DNA for analysis of single-stranded DNA using capillary electrophoresis

Capillary electrophoresis (CE) is a convenient, fast and non-radioactive method with possibilities for automatization. To analyse single-stranded DNA molecules in a more automated way, we developed a heating device to melt double-stranded DNA fragments in the capillary during electrophoresis. In this study we used this device to obtain single-stranded DNA, necessary for the detection of point mutations in DNA using the single-strand conformation polymorphism technique. Results show that double-stranded DNA molecules can be melted on-line into single-stranded DNA molecules, although not for 100%. In an attempt to find universal electrophoretic conditions for the analysis of single-stranded DNA, we investigated the influence of several parameters on the yield of single-stranded DNA molecules and on the resolution of the single-stranded DNA peaks. We demonstrate that this heating device is a technical adjustment of CE which contributes to more automated analyses of DNA fragments.     

Modified method for the determination of capillary electrophoresis nitric oxide-correlated nitrate in tissue homogenates

A modified capillary electrophoretic method for the determination of nitric oxide correlated nitrate in several tissue homogenates is described in this study. The method was developed using a running buffer consisting of 200 mM lithium chloride and 10 mM borate buffer at pH 8.5, in a fused-silica column total 82 cm, effective 43 cm length and 75 μm I.D. The signal was measured at 214 nm and controlled current of 200 μA (equivalent to 12.7 kV) was applied in the reversed polarity direction. The sample was injected by vacuum pressure 50 ms (25 nl). In these conditions, bromide as internal standard and nitrate appeared at 7.2 and 8.9 min, respectively. Whole validation procedures were applied and satisfactory results were obtained. The nitrate levels of the tissue homogenates of control and -NAME applied (heart, brain, kidney, stomach, lung, testis and liver) were monitored by the present method and it was decided that the method is precise and accurate.     

A recommended workflow for DNase I footprinting using a capillary electrophoresis genetic analyzer

Fragment analysis was developed to determine the sizes of DNA fragments relative to size standards of known lengths using a capillary electrophoresis genetic analyzer. This approach has since been adapted for use in DNA footprinting. However, DNA footprinting requires accurate determination of both fragment length and intensity, imposing specific demands on the experimental design. Here we delineate essential considerations involved in optimizing the fragment analysis workflow for use in DNase I footprinting to ensure that changes in DNase I cleavage patterns may be reliably identified.