Efficient Organic Solar Cells with Extremely High Open‐Circuit Voltages and Low Voltage Losses by Suppressing Nonradiative Recombination Losses

One of the most important factors that limits the efficiencies of bulk‐heterojunction organic solar cells (OSCs) is the modest open‐circuit voltage (V_oc) due to their large voltage loss (V_loss) caused by significant nonradiative recombination loss. To boost the performance of OSCs toward their theoretical limit, developing high‐performance donor: acceptor systems featuring low V_loss with suppressed nonradiative recombination losses (<0.30 V) is desired. Herein, high performance OSCs based on a polymer donor benzodithiophene‐difluorobenzoxadiazole‐2‐decyltetradecyl (BDT‐ffBX‐DT) and perylenediimide‐based acceptors (PDI dimer with spirofluorene linker (SFPDI), PDI4, and PDI6) are reported which offer a high power conversion efficiency (PCE) of 7.5%, 56% external quantum efficiency associated with very high V_oc (>1.10 V) and low V_loss (<0.60 V). A high V_oc up to 1.23 V is achieved, which is among the highest values reported for OSCs with a PCE beyond 6%, to date. These attractive results are benefit from the suppressed nonradiative recombination voltage loss, which is as low as 0.20 V. This value is the lowest value for OSCs so far and is comparable to high performance crystalline silicon and perovskite solar cells. These results show that OSCs have the potential to achieve comparable V_oc and voltage loss as inorganic photovoltaic technologies.     

Achieving Both Enhanced Voltage and Current through Fine‐Tuning Molecular Backbone and Morphology Control in Organic Solar Cells

It is a great challenge to simultaneously improve the two tangled parameters, open circuit voltage (V_oc) and short circuit current density (J_sc) for organic solar cells (OSCs). Herein, such a challenge is addressed by a synergistic approach using fine‐tuning molecular backbone and morphology control simultaneously by a simple yet effective side chain modulation on the backbone of an acceptor–donor–acceptor (A–D–A)‐type acceptor. With this, two terthieno[3,2‐b]thiophene (3TT) based A–D–A‐type acceptors, 3TT‐OCIC with backbone modulation and 3TT‐CIC without such modification, are designed and synthesized. Compared with the controlled molecule 3TT‐CIC, 3TT‐OCIC shows power conversion efficiency (PCE) of 13.13% with improved V_oc of 0.69 V and J_sc of 27.58 mA cm^?2, corresponding to PCE of 12.15% with V_oc of 0.65 V and J_sc of 27.04 mA cm^?2 for 3TT‐CIC–based device. Furthermore, with effective near infrared absorption, 3TT‐OCIC is used as the rear subcell acceptor in a tandem device and gave an excellent PCE of 15.72%.     

An Omnidirectionally Stretchable Piezoelectric Nanogenerator Based on Hybrid Nanofibers and Carbon Electrodes for Multimodal Straining and Human Kinematics Energy Harvesting

Stretchable piezoelectric nanogenerators (SPENGs) for human kinematics energy harvesting have limited use due to the low stretchability or mechanical robustness and the difficulty of structural design for omnidirectional stretchability. This study reports an efficient, omnidirectionally stretchable, and robust SPENG based on a stretchable graphite electrode on a 3D micropatterned stretchable substrate and a stacked mat of piezoelectric nanofibers. The stacked mat of free‐standing nanofibers is alternatively composed of nanocomposite nanofibers of barium titanate nanoparticles embedded in polyurethane and poly(vinylidene fluoride‐trifluoroethylene) nanofibers. The nanofiber SPENG (nf‐SPENG) exhibits a high stretchability of 40% and high mechanical durability up to 9000 stretching cycles at 30% strain, which are attributed to the stress‐relieving nature of the 3D micropattern on the substrate and the free‐standing stacked hybrid nanofibers. The nf‐SPENG produces a peak open circuit voltage (V_oc) and short circuit current (I_sc) of 9.3 V and 189 nA, respectively. The nf‐SPENG is demonstrated to harvest the energy from human kinematics while walking when placed over the knee cap of a subject, generating a maximum V_oc of 10.1 V. The omnidirectional stretchability, efficiency, facile fabrication process, mechanical durability, environmentally friendly lead‐free components, and response to multimodal straining make this device suitable for self‐powered wearable sensing systems.     

Effects of Shortened Alkyl Chains on Solution‐Processable Small Molecules with Oxo‐Alkylated Nitrile End‐Capped Acceptors for High‐Performance Organic Solar Cells

Solution‐processable small molecules are significant for producing high‐performance bulk heterojunction organic solar cells (OSCs). Shortening alkyl chains, while ensuring proper miscibility with fullerene, enables modulation of molecular stacking, which is an effective method for improving device performance. Here, the design and synthesis of two solution‐processable small molecules based on a conjugated backbone with a novel end‐capped acceptor (oxo–alkylated nitrile) using octyl and hexyl chains attached to π–bridge, and octyl and pentyl chains attached to the acceptor is reported. Shortening the length of the widely used octyl chains improves self‐assembly and device performance. Differential scanning calorimetry and grazing incidence X‐ray diffraction results demonstrated that the molecule substituted by shorter chains shows tighter molecular stacking and higher crystallinity in the mixture with 6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) and that the power conversion efficiency (PCE) of the OSC is as high as 5.6% with an open circuit voltage (V_oc) of 0.87 V, a current density (J_sc) of 9.94 mA cm^‐2, and an impressive filled factor (FF) of 65% in optimized devices. These findings provide valuable insights into the production of highly efficient solution‐processable small molecules for OSCs.     

Efficiency Enhancement of Organic Solar Cells Using Hydrophobic Antireflective Inverted Moth‐Eye Nanopatterned PDMS Films

Poly‐dimethylsiloxane (PDMS) films with 2D periodic inverted moth‐eye nanopatterns on one surface are implemented as antireflection (AR) layers on a glass substrate for efficient light capture in encapsulated organic solar cells (OSCs). The inverted moth‐eye nanopatterned PDMS (IMN PDMS) films are fabricated by a soft imprint lithographic method using conical subwavelength grating patterns formed by laser interference lithography/dry etching. Their optical characteristics, together with theoretical analysis using rigorous coupled‐wave analysis simulation, and wetting behaviors are investigated. For a period of 380 nm, IMN PDMS films laminated on glass substrates exhibit a hydrophobic surface with a water contact angle (θ_CA) of ≈120° and solar weighted transmittance (SWT) of ≈94.2%, both significantly higher than those (θ_CA≈ 36° and SWT ≈ 90.3%) of bare glass substrates. By employing IMN PDMS films with a period of 380 nm on glass substrates for OSCs, an enhanced power conversion efficiency (PCE) of 6.19% is obtained mainly due to the increased short‐circuit current density (J_sc) of 19.74 mA cm^‐2 compared to the OSCs with the bare glass substrates (PCE = 5.16% and J_sc = 17.25 mA cm^‐2). For the OSCs, the device stability is also studied.     

High Performance Thick‐Film Nonfullerene Organic Solar Cells with Efficiency over 10% and Active Layer Thickness of 600 nm

Developing efficient organic solar cells (OSCs) with relatively thick active layer compatible with the roll to roll large area printing process is an inevitable requirement for the commercialization of this field. However, typical laboratory OSCs generally exhibit active layers with optimized thickness around 100 nm and very low thickness tolerance, which cannot be suitable for roll to roll process. In this work, high performance of thick‐film organic solar cells employing a nonfullerene acceptor F–2Cl and a polymer donor PM6 is demonstrated. High power conversion efficiencies (PCEs) of 13.80% in the inverted structure device and 12.83% in the conventional structure device are achieved under optimized conditions. PCE of 9.03% is obtained for the inverted device with active layer thickness of 500 nm. It is worth noting that the conventional structure device still maintains the PCE of over 10% when the film thickness of the active layer is 600 nm, which is the highest value for the NF‐OSCs with such a large active layer thickness. It is found that the performance difference between the thick active layer films based conventional and inverted devices is attributed to their different vertical phase separation in the active layers.     

Controllable ZnMgO Electron‐Transporting Layers for Long‐Term Stable Organic Solar Cells with 8.06% Efficiency after One‐Year Storage

Currently, one main challenge in organic solar cells (OSCs) is to achieve both good stability and high power conversion efficiencies (PCEs). Here, highly efficient and long‐term stable inverted OSCs are fabricated by combining controllable ZnMgO (ZMO) cathode interfacial materials with a polymer:fullerene bulk‐heterojunction. The resulting devices based on the nanocolloid/nanoridge ZMO electron‐transporting layers (ETLs) show greatly enhanced performance compared to that of the conventional devices or control devices without ZMO or with ZnO ETLs. The ZMO‐based OSCs maintain 84%–93% of their original PCEs over 1‐year storage under ambient conditions. An initial PCE of 9.39% is achieved for the best device, and it still retains a high PCE of 8.06% after 1‐year storage, which represents a record high value for long‐term stable OSCs. The excellent performance is attributed to the enhanced electron transportation/collection, reduced interfacial energy losses, and improved stability of the nanocolloid ZMO ETL. These findings provide a promising way to develop OSCs with high efficiencies and long device lifetime towards practical applications.     

Printed Nonfullerene Organic Solar Cells with the Highest Efficiency of 9.5%

The current work reports a high power conversion efficiency (PCE) of 9.54% achieved with nonfullerene organic solar cells (OSCs) based on PTB7‐Th donor and 3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene) (ITIC) acceptor fabricated by doctor‐blade printing, which has the highest efficiency ever reported in printed nonfullerene OSCs. Furthermore, a high PCE of 7.6% is realized in flexible large‐area (2.03 cm²) indium tin oxide (ITO)‐free doctor‐bladed nonfullerene OSCs, which is higher than that (5.86%) of the spin‐coated counterpart. To understand the mechanism of the performance enhancement with doctor‐blade printing, the morphology, crystallinity, charge recombination, and transport of the active layers are investigated. These results suggest that the good performance of the doctor‐blade OSCs is attributed to a favorable nanoscale phase separation by incorporating 0.6 vol% of 1,8‐diiodooctane that prolongs the dynamic drying time of the doctor‐bladed active layer and contributes to the migration of ITIC molecules in the drying process. High PCE obtained in the flexible large‐area ITO‐free doctor‐bladed nonfullerene OSCs indicates the feasibility of doctor‐blade printing in large‐scale fullerene‐free OSC manufacturing. For the first time, the open‐circuit voltage is increased by 0.1 V when 1 vol% solvent additive is added, due to the vertical segregation of ITIC molecules during solvent evaporation.     

High-Reproducibility Layer-by-Layer Non-Fullerene Organic Photovoltaics with 19.18% Efficiency Enabled by Vacuum-Assisted Molecular Drift Treatment

The thin film deposition engineering of layer-by-layer (LbL) non-fullerene organic solar cells (OSCs) favors vertical phase distributions of donor:acceptor (D:A), effectively boosting the power conversion efficiency (PCE). However, previous deposition strategies mainly aimed at optimizing the morphology of LbL films, and paid limited attention to the reproducibility of device performance. To achieve high device performance and maintain reproducibility, a strategy for hierarchical morphology manipulation in LbL OSCs is developed. A series of LbL devices are fabricated by introducing vacuum-assisted molecular drift treatment (VMDT) to the donor or acceptor layer individually or simultaneously to elucidate the functionalities of this treatment. Essentially, the VMDT provides an extended drift driving force to manipulate the donor and acceptor molecules, resulting in a well-defined vertical phase distribution and ordered molecular packing. These enhancements facilitate improvement in the D:A interface area and charge transport channel, ultimately contributing to impressive PCEs of 19.18% from 18.27% in the LbL devices. More importantly, using VMDT overcomes the notorious batch-dependent and heat treatment degradation issues of OSCs, leading to excellent batch-to-batch reproducibility and enhanced stability of the devices. This reported method provides a promising strategy available for industrial and laboratory use to controllably manipulate the morphology of LbL OSCs.     

Precise Control of Phase Separation Enables 12% Efficiency in All Small Molecule Solar Cells

Compared to conjugated polymers, small‐molecule organic semiconductors present negligible batch‐to‐batch variations, but presently provide comparatively low power conversion efficiencies (PCEs) in small‐molecular organic solar cells (SM‐OSCs), mainly due to suboptimal nanomorphology. Achieving precise control of the nanomorphology remains challenging. Here, two new small‐molecular donors H13 and H14 , created by fluorine and chlorine substitution of the original donor molecule H11 , are presented that exhibit a similar or higher degree of crystallinity/aggregation and improved open‐circuit voltage with IDIC‐4F as acceptor. Due to kinetic and thermodynamic reasons, H13 ‐based blend films possess relatively unfavorable molecular packing and morphology. In contrast, annealed H14 ‐based blends exhibit favorable characteristics, i.e., the highest degree of aggregation with the smallest paracrystalline π–π distortions and a nanomorphology with relatively pure domains, all of which enable generating and collecting charges more efficiently. As a result, blends with H13 give a similar PCE (10.3%) as those made with H11 (10.4%), while annealed H14 ‐based SM‐OSCs have a significantly higher PCE (12.1%). Presently this represents the highest efficiency for SM‐OSCs using IDIC‐4F as acceptor. The results demonstrate that precise control of phase separation can be achieved by fine‐tuning the molecular structure and film formation conditions, improving PCE and providing guidance for morphology design.     

Sequential Blade‐Coated Acceptor and Donor Enables Simultaneous Enhancement of Efficiency,Stability, and Mechanical Properties for Organic Solar Cells

As a predominant fabrication method of organic solar cells (OSCs), casting of a bulk heterojunction (BHJ) structure presents overwhelming advantages for achieving higher power conversion efficiency (PCE). However, long‐term stability and mechanical strength are significantly crucial to realize large‐area and flexible devices. Here, controlling blend film morphology is considered as an effective way toward co‐optimizing device performance, stability, and mechanical properties. A PCE of 12.27% for a P‐i‐N‐structured OSC processed by sequential blade casting (SBC) is reported. The device not only outperforms the as‐cast BHJ devices (11.01%), but also shows impressive stability and mechanical properties. The authors corroborate such enhancements with improved vertical phase separation and purer phases toward more efficient transport and collection of charges. Moreover, adaptation of SBC strategy here will result in thermodynamically favorable nanostructures toward more stable film morphology, and thus improving the stability and mechanical properties of the devices. Such co‐optimization of OSCs will pave ways toward realizing the highly efficient, large‐area, flexible devices for future endeavors.     

Oligothiophene Additive-Assisted Morphology Control and Recombination Suppression Enable High-Performance Organic Solar Cells

Tuning the morphology through processing additives represents one of the most promising strategies to boost the performance of organic solar cells (OSCs). However, it remains unclear how oligothiophene-based solid additives influence the molecular packing and performance of OSCs. Here, two additives namely 2T and 4T, are introduced into state-of-the-art PM6:Y6-based OSCs to understand how they influence the film formation process, nanoscale morphology, and the photovoltaic performance. It is found that the 2T additive can improve the molecular packing of both donor polymer and non-fullerene acceptor, resulting in lower Urbach energy and reduced energy loss. Furthermore, the blend film with 2T treatment displays enhanced domain purity and a more favorable distribution of the acceptor and donor materials in the vertical direction, which can enhance charge extraction efficiency while simultaneously suppressing charge recombination. Consequently, OSCs processed with 2T additive realize a promising efficiency of 18.1% for PM6:Y6-based devices. Furthermore, the general applicability of the additive is demonstrated, and an impressive efficiency of 18.6% for PM6:L8-BO-based OSCs is achieved. These findings highlight that the uncomplicated oligothiophenes have excellent potential in fine-adjustment of the active layer morphology, which is crucial for the future development of OSCs.     

Significant Effect of Fluorination on Simultaneously Improving Work Function and Transparency of Anode Interlayer for Organic Solar Cells

Since the highest occupied molecular orbital (HOMO) level of donors in organic solar cells (OSCs) is being constantly downshifted for achieving high open‐circuit voltage (V_oc), a further enhancement of the anode work function (WF) is required. Herein, an effective approach of fluorination is demonstrated to simultaneously improve the WF and transparency for anode interlayer (AIL) material. By fluorination, in combination with the dialysis treatment in LiCl solution, the WF of PCP‐2F‐Li could be significantly enhanced from 4.86 to 5.0 eV, as compared to PCP‐Na. Meanwhile, the transparency of the polymer is also improved. As a result, PCP‐2F‐Li can be used to modify efficient active layers consisting of polymer donors with deep HOMO levels, such as PBDB‐T‐2F:IT‐4F, and an outstanding power conversion efficiency (PCE) of 12.7% is achieved in the corresponding device with a high V_oc of 0.84 V. This result represents the highest efficiency for the OSCs using a solution‐processed pH‐neutral AIL, which is beneficial to the low‐cost fabrication of high‐performance OSCs with improved stability. More importantly, PCP‐2F‐Li could be processed by blade coating for making large‐area device of 1 cm², and a PCE of 10.6% is achieved, bringing a promising prospect for the large‐area device fabrication.     

Additive‐Free Organic Solar Cells with Power Conversion Efficiency over 10%

Nowadays, solvent additives are widely used in organic solar cells (OSCs) to tune the nano‐morphology of the active blend film and enhance the device performance. With their help, power conversion efficiencies (PCEs) of OSCs have recently stepped over 10%. However, residual additive in the device can induce undesirable morphological change and also accelerate photo‐oxidation degradation of the active blend film. Thereby, their involvements are actually unfavorable for practical applications. Here, a donor material PThBDTP is employed, and PThBDTP:PC71BM based OSCs are fabricated. A PCE of over 10% is achieved without using any additives and film post‐treatments. The device displays a high open‐circuit voltage of 0.977 V, a large short‐circuit current density of 13.49 mA cm^‐2, and a high fill factor of 76.3%. These results represent an important step towards developing high‐efficiency additive‐free OSCs.     

Bandgap Narrowing in Non‐Fullerene Acceptors: Single Atom Substitution Leads to High Optoelectronic Response Beyond 1000 nm

Two narrow bandgap non‐fullerene acceptors (NBG‐NFAs), namely, COTIC‐4F and SiOTIC‐4F, are designed and synthesized for the fabrication of efficient near‐infrared organic solar cells (OSCs). The chemical structures of the NBG‐NFAs contain a D′‐D‐D′ electron‐rich internal core based on a cyclopentadithiophene (or dithienosilole) (D) and alkoxythienyl (D′) core, end‐capped with the highly electron‐deficient unit 2‐(5,6‐difluoro‐3‐oxo‐2,3‐dihydro‐1H‐inden‐1‐ylidene)malononitrile (A), ultimately providing a A‐D′‐D‐D′‐A molecular configuration that enhances the intramolecular charge transfer characteristics of the excited states. One can thereby reduce the optical bandgap (E_g^opt) to as low as ≈1.10 eV, one of the smallest values for NFAs reported to date. In bulk‐heterojunction (BHJ) OSCs, NBG‐NFA blends with the polymer donor PTB7‐Th yield power conversion efficiencies (PCE) of up to 9.0%, which is particularly high when compared against a range of NBG BHJ blends. Most significantly, it is found that, despite the small energy loss (E_g^opt ? eV_OC) of 0.52 eV, the PTB7‐Th/NBG‐NFA bulk heterojunction blends can yield short‐circuit current densities of up to 22.8 mA cm^?2, suggesting that the design and application of NBG‐NFA materials have substantial potential to further improve the PCE of OSCs.     

A High‐Performance D–A Copolymer Based on Dithieno[3,2‐b:2′,3′‐d]Pyridin‐5(4H)‐One Unit Compatible with Fullerene and Nonfullerene Acceptors in Solar Cells

Development of high‐performance donor–acceptor (D–A) copolymers is vital in the research of polymer solar cells (PSCs). In this work, a low‐bandgap D–A copolymer based on dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one unit (DTP), PDTP4TFBT, is developed and used as the donor material for PSCs with PC₇₁BM or ITIC as the acceptor. PDTP4TFBT:PC₇₁BM and PDTP4TFBT:ITIC solar cells give power conversion efficiencies (PCEs) up to 8.75% and 7.58%, respectively. 1,8‐Diiodooctane affects film morphology and device performance for fullerene and nonfullerene solar cells. It inhibits the active materials from forming large domains and improves PCE for PDTP4TFBT:PC₇₁BM cells, while it promotes the aggregation and deteriorates performance for PDTP4TFBT:ITIC cells. The ternary‐blend cells based on PDTP4TFBT:PC₇₁BM:ITIC (1:1.2:0.3) give a decent PCE of 9.20%.     

Evidencing Excellent Thermal‐ and Photostability for Single‐Component Organic Solar Cells with Inherently Built‐In Microstructure

Solution‐processed organic solar cells (OSCs) are promising low‐cost, flexible, portable renewable sources for future energy supply. The state‐of‐the‐art OSCs are typically fabricated from a bulk‐heterojunction (BHJ) active layer containing well‐mixed donor and acceptor molecules in the nanometer regime. However, BHJ solar cells suffer from stability problems caused by the severe morphological changes upon thermal or illumination stress. In comparison, single‐component organic solar cells (SCOSCs) based on a double‐cable conjugated polymer with a covalently stabilized microstructure is suggested to be a key strategy for superior long‐term stability. Here, the thermal‐ and photostability of SCOSCs based on a model double‐cable polymer is systematically investigated. It is encouraging to find that under 90 °C & 1 sun illumination, the performance of SCOSCs remains substantially stable. Transport measurements show that charge generation and recombination (lifetime and recombination order) hardly change during the aging process. Particularly, the SCOSCs exhibit ultrahigh long‐term thermal stability with 100% PCE remaining after heating at temperature up to 160 °C for over 400 h, indicating an excellent candidate for extremely rugged applications.     

Layer‐by‐Layer Solution‐Processed Low‐Bandgap Polymer‐PC61BM Solar Cells with High Efficiency

Polymer solar cells (PSCs) are fabricated without solvent additives using a low‐bandgap polymer, PBDTTT‐C‐T, as the donor and [6,6]‐phenyl‐C61‐butyric‐acid‐methyl‐ester (PC₆₁BM) as the acceptor. Donor‐acceptor blend and layer‐by‐layer (LL) solution process are used to form active layers. Relative to the blend devices, the LL devices exhibit stronger absorption, better vertical phase separation, higher hole and electron mobilities, and better charge extraction at correct electrodes. As a result, after thermal annealing the LL devices exhibit an average power conversion efficiency (PCE) of 6.86%, which is much higher than that of the blend devices (4.31%). The best PCE of the LL devices is 7.13%, which is the highest reported for LL processed PSCs and among the highest reported for PC₆₁BM‐based single‐junction PSCs.     

Overcoming the “Light‐Soaking” Issue in Inverted Organic Solar Cells by the Use of Al:ZnO Electron Extraction Layers

A common phenomenon of organic solar cells (OSCs) incorporating metal‐oxide electron extraction layers is the requirement to expose the devices to UV light in order to improve device characteristics – known as the so‐called “light‐soaking” issue. This behaviour appears to be of general validity for various metal‐oxide layers, various organic donor/acceptor systems, and regardless if single junction devices or multi stacked cells are considered. The requirement of UV exposure of OSCs may impose severe problems if substrates with limited UV transmission, UV blocking filters or UV to VIS down‐conversion concepts are applied. In this paper, we will demonstrate that this issue can be overcome by the use of Al doped ZnO (AZO) as electron extraction interlayer. In contrast to devices based on TiO_x and ZnO, the AZO devices show well‐behaved solar cell characteristics with a high fill factor (FF) and power conversion efficiency (PCE) even without the UV spectral components of the AM1.5 solar spectrum. As opposed to previous claims, our results indicate that the origin of s‐shaped characteristics of the OSCs is the metal‐oxide/organic interface. The electronic structures of the TiO_x/fullerene and AZO/fullerene interfaces are studied by photoelectron spectroscopy, revealing an electron extraction barrier for the TiO_x/fullerene case and facilitated electron extraction for AZO/fullerene. These results are of general relevance for organic solar cells based on various donor acceptor active systems.     

15% Efficiency Tandem Organic Solar Cell Based on a Novel Highly Efficient Wide‐Bandgap Nonfullerene Acceptor with Low Energy Loss

A tandem organic solar cell (OSC) is a valid structure to widen the photon response range and suppress the transmission loss and thermalization loss. In the past few years, the development of low‐bandgap materials with broad absorption in long‐wavelength region for back subcells has attracted considerable attention. However, wide‐bandgap materials for front cells that have both high short‐circuit current density (J_SC) and open‐circuit voltage (V_OC) are scarce. In this work, a new fluorine‐substituted wide‐bandgap small molecule nonfullerene acceptor TfIF‐4FIC is reported, which has an optical bandgap of 1.61 eV. When PBDB‐T‐2F is selected as the donor, the device offers an extremely high V_OC of 0.98 V, a high J_SC of 17.6 mA cm^?2, and a power conversion efficiency of 13.1%. This is the best performing acceptor with such a wide bandgap. More importantly, the energy loss in this combination is 0.63 eV. These properties ensure that PBDB‐T‐2F:TfIF‐4FIC is an ideal candidate for the fabrication of tandem OSCs. When PBDB‐T‐2F:TfIF‐4FIC and PTB7‐Th:PCDTBT:IEICO‐4F are used as the front cell and the back cell to construct tandem solar cells, a PCE of 15% is obtained, which is one of best results reported to date in the field of organic solar cells.