Luminescence and energy‐transfer properties of color‐tunable Ca2Mg0.25Al1.5Si1.25O7:Ce3+/Eu2+/Tb3+ phosphors for ultraviolet light‐emitting diodes

A series of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺/Eu²⁺/Tb³⁺ phosphors was been prepared via a conventional high temperature solid‐state reaction and their luminescence properties were studied. The emission spectra of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺ and Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Tb³⁺ phosphors show not only a band due to Ce³⁺ ions (409 nm) but also as a band due to Eu²⁺ (520 nm) and Tb³⁺ (542 nm) ions. More importantly, the effective energy transfer from Ce³⁺ to Eu²⁺ and Tb³⁺ ions was confirmed and investigated by emission/excitation spectra and luminescent decay behaviors. Furthermore, the energy level scheme and energy transfer mechanism were investigated and were demonstrated to be of resonant type via dipole–dipole (Ce³⁺ to Eu²⁺) and dipole–quadrupole (Ce³⁺ to Tb³⁺) reactions, respectively. Under excitation at 350 nm, the emitting color could be changed from blue to green by adjusting the relative doping concentration of Ce³⁺ and Eu²⁺ ions as well as Ce³⁺ and Tb³⁺ ions. The above results indicate that Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺/Tb³⁺ are promising single‐phase blue‐to‐green phosphors for application in phosphor conversion white‐light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Intensity enhancement of photoluminescence in Tb3+/Eu3+ co-doped Ca14Zn6Al10O35 phosphor for WLEDs

This article focuses on the effect of monovalent cation doping on the optical properties of rare earth (RE = Eu³⁺, Tb³⁺) co-doped Ca₁₄Zn₆Al₁₀O₃₅ which has been synthesized by a low temperature combustion method. Crystalline phase of the Ca₁₄Zn₆Al₁₀O₃₅ phosphor was examined and confirmed by X-ray diffraction measurement. Under near-ultraviolet light excitation Eu³⁺-doped Ca₁₄Zn₆Al₁₀O₃₅ phosphor exhibit characterization of Eu³⁺ emission bands that are located at a maximum wavelength (λ_max) of approximately 470 nm and other peaks centred at 593 nm and 615 nm, respectively. With Tb³⁺-doped Ca₁₄Zn₆Al₁₀O₃₅ phosphor showing a green emission band centred at 544 nm under near-ultraviolet range. Furthermore, we studied the energy transfer process in Eu³⁺/Tb³⁺pair and enhancement in photoluminescence (PL) intensity with doping different charge compensation. Here we obtained the optimum PL emission intensity of the phosphor in broad and intense visible spectral range which may be significant for the fabrication of white light emitting diodes (WLEDs).     

Energy transfer induced white‐light‐emitting phosphor by co‐doping Ce3+, Tb3+ and Mn2+ into the single Ba9Lu2Si6O24 host

In the Ba₉Lu₂Si₆O₂₄ (BLS) host, Ce³⁺ shows cyan emissions peaking at 490 nm under 400 nm excitations. BLS:Tb³⁺ only can be effectively excited by 254 nm light and gives rise to green emissions at 553 nm. However, both the cyan and green emissions can be obtained in BLS:Ce³⁺,Tb³⁺ under 400 nm excitations due to effective energy transfers from Ce³⁺ to Tb³⁺. BLS:Mn²⁺ shows red emissions peaking at 610 nm under 414 nm excitations. By co‐doping Ce³⁺, Tb³⁺ and Mn²⁺, tunable full‐color emissions were obtained. The BLS:0.3Ce³⁺,0.6Tb³⁺,0.15Mn²⁺ single phosphor exhibits a white light with a high color rendering index of 85 and a correlated color temperature of 5480 K under 400 nm excitation.     

The high thermal stability of white emitting phosphor Mg2Y2Al2Si2O12:Dy3+,Eu3+,La3+/Lu3+ for white light emitting diodes

A series of Mg₂Y₂Al₂Si₂O₁₂:Dy³⁺,Eu³⁺ was prepared using a solid-state method, and the phosphor emitted white light by tuning the ratio of Dy³⁺/Eu³⁺. The effects of La³⁺/Lu³⁺ on the structure and luminescence properties of Mg₂Y₂Al₂Si₂O₁₂:Dy³⁺,Eu³⁺ were explored. Under the influence of bond length and twist, the luminescence intensity of the materials increased first and then decreased under excitation with ultraviolet light. The lattice distortion of the trivalent cation La³⁺-substituted Mg₂Y₂Al₂Si₂O₁₂:Dy³⁺ and Eu³⁺ phosphors was reduced, the symmetry of polyhedron occupied by the luminescence centre improved, and the thermal stability of the luminescence centre improved to a certain extent. White light emitting diodes (LEDs) were fabricated by combining a 370 nm LED chip and the Mg₂Y₂Al₂Si₂O₁₂:Dy³⁺,Eu³⁺,La³⁺ (Mg₂Y₂Al₂Si₂O₁₂:Dy³⁺,Eu³⁺,Lu³⁺) phosphor. The results showed that Mg₂Y₂Al₂Si₂O₁₂:Dy³⁺,Eu³⁺,La³⁺/Lu³⁺ may have potential application in the area of white LEDs.     

Rare earth activated yttrium aluminate phosphors with modulated luminescence

Yttrium aluminate (Y₃A₅O₁₂) was doped with different rare earth ions (i.e. Gd³⁺, Ce³⁺, Eu³⁺ and/or Tb³⁺) in order to obtain phosphors (YAG:RE) with general formula,Y_3‐x‐aGd_xRE_aAl₅O₁₂ (x = 0; 1.485; 2.97 and a = 0.03). The synthesis of the phosphor samples was done using the simultaneous addition of reagents technique. This study reveals new aspects regarding the influence of different activator ions on the morpho‐structural and luminescent characteristics of garnet type phosphor. All YAG:RE phosphors are well crystallized powders containing a cubic‐Y₃Al₅O₁₂ phase as major component along with monoclinic‐Y₄Al₂O₉ and orthorhombic‐YAlO₃ phases as the impurity. The crystallites dimensions of YAG:RE phosphors vary between 38 nm and 88 nm, while the unit cell slowly increase as the ionic radius of the activator increases. Under UV excitation, YAG:Ce exhibits yellow emission due to electron transition in Ce³⁺ from the 5d level to the ground state levels (²F_5/2, ²F_7/2). The emission intensity of Ce³⁺ is enhanced in the presence of the Tb³⁺ ions and is decreased in the presence of Eu³⁺ ions due to some radiative or non‐radiative processes that take place between activator ions. By varying the rare earth ions, the emission colour can be modulated from green to white and red. Copyright © 2015 John Wiley & Sons, Ltd.     

Green‐light emission through energy transfer from Ce3+ to Tb3+ ions in the Li2SO4–Al2(SO4)3 system

An energy transfer process from Ce³⁺ to Tb³⁺ ions was successfully achieved in a Li₂SO₄–Al₂(SO₄)₃ mixed‐sulphate system. A wet‐chemical synthesis was employed to prepare the Li₂SO₄–Al₂(SO₄)₃ system by doping Ce³⁺ and Tb³⁺ ions individually as well as collectively. The phases were identified using X‐ray diffraction studies. The as‐prepared samples were characterized by FT‐IR and photoluminescence measurements. Green‐light emission was exhibited by Ce³⁺, Tb³⁺ co‐doped Li₂SO₄–Al₂(SO₄)₃ system, thus, indicating its potential as a material for display devices or in the lamp industry.     

Luminescent properties of single‐phase Ba2‐x‐1.5y‐1.5zP2O7:xEu2+,yCe3+, zTb3+ phosphors for white light‐emitting diode

A series of Ba₂P₂O₇:xEu²⁺,yCe³⁺,zTb³⁺ phosphors was synthesized via a co‐precipitation method, then their crystal structure, quantum efficiency and luminescent properties were analyzed by XRD and FL, respectively. The results showed that these phosphors not only presented the excitation characteristics of Ba₂P₂O₇:xEu²⁺,zTb³⁺, but also exhibited that of the Ba₂P₂O₇:yCe³⁺,zTb³⁺ phosphor. Meanwhile, the tri‐doped phosphor showed a stronger absorption around 320 nm in contrast with the Eu²⁺/Ce³⁺:Tb³⁺ co‐doped phosphor. Not only can energy transfer from Ce³⁺→Eu²⁺ be observed; the energy transfer mechanism from Eu²⁺ to Tb³⁺ is discussed in the tri‐doped system. Ce³⁺ affects the luminescence properties of Ba₂P₂O₇:xEu²⁺,yCe³⁺,zTb³⁺ phosphors just as the sensitizer whereas Eu²⁺ is considered both as the sensitizer and the activator. The chromaticity coordinates of tri‐doped phosphors excited at 320 nm stayed steadily in the bluish‐white light region,and the emitted color and color temperature (CCT) of these phosphors could be tuned by adjusting the relative contents of Eu²⁺, Ce³⁺ and Tb³⁺. Hence, the single phase Ba₂P₂O₇:xEu²⁺,yCe³⁺,zTb³⁺ phosphors may be considered as potential candidates for white light‐emitting diodes.     

Study on luminescence properties of Ce3+ and Eu3+ ions in a nanocrystalline hexagonal Zn4Al22O37 novel system

The present communication is strongly focused on the investigation of synthesis, structural and luminescence properties of cerium (Ce³⁺)- and europium (Eu³⁺)-activated Zn₄Al₂₂O₃₇ phosphors. Ce³⁺- and Eu³⁺-doped Zn₄Al₂₂O₃₇ novel phosphors were prepared using a solution combustion synthesis route. Structural properties were studied using powder X-ray diffraction and high-resolution transverse electron microscopy. The optical properties were studied using ultraviolet–visible light spectroscopy and Fourier transform infrared spectroscopy; luminescence properties were studied using a photoluminescence (PL) technique. The crystal structure of the prepared Zn₄Al₂₂O₃₇ host and Ce³⁺- and Eu³⁺-activated Zn₄Al₂₂O₃₇ phosphors was investigated and was found to have a hexagonal structure. The measured PL emission spectrum of the Ce³⁺-doped Zn₄Al₂₂O₃₇ phosphor showed an intense and broad emission band centred at 421 nm under a 298 nm excitation wavelength. By contrast, the Eu³⁺-doped Zn₄Al₂₂O₃₇ phosphor exhibited two strong and intense emission bands at approximately 594 nm (orange) and 614 nm (red), which were monitored under 395 nm excitation. The Commission Internationale de l’Eclairage (CIE) colour coordinates of the Ce³⁺-doped Zn₄Al₂₂O₃₇ were investigated and found to be x = 0.1567, y = 0.0637 (blue) at 421 nm and for Eu³⁺-doped Zn₄Al₂₂O₃₇ were x = 0.6018, y = 0.3976 (orange) at 594 nm and x = 0.6779, y = 0.3219 (red) at 614 nm emission. The luminescence behaviour of the synthesized phosphors suggested that these phosphors may be used in lighting applications.     

Luminescent properties and energy transfer in the green phosphors LaBSiO5:Tb3+,Ce3+

LaBSiO₅ phosphors doped with Ce³⁺ and Tb³⁺ were synthesized using the conventional solid‐state method at 1100 °C. The phase purity and luminescent properties of these phosphors are investigated. LaBSiO₅:Tb³⁺ phosphors show intense green emission, and LaBSiO₅ phosphors doped with Ce³⁺ show blue–violet emission under UV light excitation. LaBSiO₅ phosphors co‐doped with Ce³⁺ and Tb³⁺ exhibit blue–violet and green emission under excitation by UV light. The blue–violet emission is due to the 5d–4f transition of Ce³⁺ and the green emission is ascribed to the ⁵D₄ → ⁷ F₅ transition of Tb³⁺. The spectral overlap between the excitation band of Tb³⁺ and the emission band of Ce³⁺ supports the occurrence of energy transfer from Ce³⁺ to Tb³⁺, and the energy transfer process was investigated. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and photoluminescence characteristics of (Y,Gd)BO3:RE (RE = Eu3+, Ce3+, Dy3+ and Tb3+) phosphors for blue chip and near‐UV white LEDs

A series of Eu³⁺‐, Ce³⁺‐, Dy³⁺‐ and Tb³⁺‐doped (Y,Gd)BO₃ phosphors was synthesized by a solid‐state diffusion method. X‐Ray diffraction confirmed their hexagonal structure and the scanning electron microscopy results showed crystalline particles. The excitation spectra revealed that (Y,Gd)BO₃ phosphors doped with Eu³⁺, Ce³⁺ , Dy³⁺ and Tb³⁺ are effectively excited with near UV‐light of 395 nm/blue light, 364, 351 and 314 nm, respectively. Photoluminescence spectra of Eu³⁺‐, Ce³⁺‐ and Tb³⁺/Dy³⁺‐doped phosphor showed intense emission of reddish orange, blue and white light, respectively. The phosphor Y_0.60Gd_0.38BO₃:Ce_0.02 showed CIE 1931 color coordinates of (0.158, 0.031) and better color purity compared with commercially available blue BAM:Eu²⁺ phosphor. The phosphor (Y,Gd)BO₃ doped with Eu³⁺, Dy³⁺ and Tb³⁺ showed CIE 1931 color coordinates of (0.667, 0.332), (0.251, 0.299) and (0.333, 0.391) respectively. Significant photoluminescence characteristics of the prepared phosphors indicate that they might serve as potential candidates for blue chip and near‐UV white light‐emitting diode applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Energy transfer between Ce3+ → Gd3+ or Tb3+ in KNaSO4 microphosphor

KNaSO₄ microphosphor doped with Ce,Gd and Ce,Tb and prepared by a wet chemical method was studied using X‐ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL) characterization. KNaSO₄ has a 5‐µm particle size detected by SEM. KNaSO₄:Ce³⁺,Tb³⁺ showed blue and green emission (at 494 nm, 557 nm, 590 nm) of Tb³⁺ due to ⁵D₄ → ⁷F_J (J = 4, 5, 6) transitions. KNaSO₄:Ce³⁺,Gd³⁺ showed luminescence in the ultraviolet (UV) light region at 314 nm for an excitation at 271 nm wavelength. It was observed that efficient energy transfer took place from Ce³⁺ → Gd³⁺ and Ce³⁺ → Tb³⁺ sublattices indicating that Ce³⁺ could effectively sensitize Gd³⁺ or Tb³⁺ (green emission). Ce³⁺ emission weakened and Gd³⁺ or Tb³⁺ enhanced the emission significantly in KNaSO₄. This paper discusses the development and understanding of photoluminescence and the effect of Tb³⁺ and Gd³⁺ on KNaSO₄:Ce³⁺. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescence of the near‐ultraviolet blue‐emitting Ba9Al2Si6O24:Ce3+ phosphor

A near‐ultraviolet (NUV) blue‐emitting phosphor Ba₉Al₂Si₆O₂₄:Ce³⁺ (BAS:Ce³⁺) was synthesized using a high‐temperature solid‐state reaction. BAS:Ce³⁺ had an excitation band peak at about 328 nm and showed a blue emission band. The NUV‐blue emission band had a peak at about 386 nm with a band width of about 60 nm, attributed to the 5d–4f transition of Ce³⁺. Fluorescent decay showed an exponential model with a lifetime of 27.2 nsec. At 150°C, the luminescence intensity decreased to 68.7% compared with the intensity at room temperature.     

Effect of Ga3+ and Gd3+ ions substitution on the structural and optical properties of Ce3+‐doped yttrium aluminium garnet phosphor nanopowders

The structural and optical properties of commercially obtained Y₃Al₅O₁₂:Ce³⁺ phosphor were investigated by replacing Al³⁺ with Ga³⁺ and Y³⁺ with Gd³⁺ in the Y₃Al₅O₁₂:Ce³⁺ structure to form Y₃(Al,Ga)₅O₁₂:Ce³⁺ and (Y,Gd)₃Al₅O₁₂:Ce³⁺. X‐Ray diffraction (XRD) results showed slight 2‐theta peak shifts to lower angles when Ga³⁺ was used and to higher angles when Gd³⁺ was used, with respect to peaks from Y₃Al₅O₁₂:Ce³⁺ and JCPDS card no. 73–1370. This could be attributed to induced crystal‐field effects due to the different ionic sizes of Ga³⁺ and Gd³⁺ compared with Al³⁺ and Y³⁺. The photoluminescence (PL) spectra showed broad excitation from 350 to 550 nm with a maximum at 472 nm, and broad emission bands from 500 to 650 nm, centred at 578 nm for Y₃Al₅O₁₂:Ce³⁺ arising from the 5d → 4f transition of Ce³⁺. PL revealed a blue shift for Ga³⁺ substitution and a red shift for Gd³⁺ substitution. UV–Vis showed two absorption peaks at 357 and 457 nm for Y₃Al₅O₁₂:Ce³⁺, with peaks shifting to 432 nm for Ga³⁺ and 460 nm for Gd³⁺ substitutions. Changes in the trap levels or in the depth and number of traps due to Ce³⁺ were analysed using thermoluminescence (TL) spectroscopy. This revealed the existence of shallow and deep traps. It was observed that Ga³⁺ substitution contributes to the shallowest traps at 74 °C and fewer deep traps at 163 °C, followed by Gd³⁺ with shallow traps at 87 °C and deep traps at 146 °C. Copyright © 2016 John Wiley & Sons, Ltd.     

Novel optical properties of Ca12Al10.6Si3.4O32Cl5.4:Ce3+,Li+ phosphor for solid‐state lighting

This article reports a novel blue emission in a series of Ca₁₂Al_10.6Si_3.4O₃₂Cl_5.4:Ce³⁺ phosphor under excitation in the near‐UV wavelength range. This phosphor was prepared using the combustion method. Here, the Ce³⁺ emission band is observed over a broad range of 380–550 nm, under 365 nm excitation, and is due to 5d–4f transition. The effect of a Li⁺ charge compensator on the emission properties of the phosphor was also investigated for the first time. X‐Ray diffraction confirmed the phase purity of the synthesized phosphor. The surface morphology and elemental composition of the phosphor were studied using scanning electron microscopy and energy‐dispersive X‐ray spectroscopy. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of rare earth elements (Y,Gd and Lu) on the luminescent properties of green phosphor ZnMoO4:Tb3+

(Zn,Ln_x)MoO₄:Tb³⁺ (Ln = Y³⁺, Gd³⁺ and Lu³⁺) were prepared using the co‐precipitation method. Phase impurity, morphology and composition were investigated by power X‐ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The experimental results show that crystal structure is not destroyed after doping an appropriate amount of Y³⁺, Gd³⁺ and Lu³⁺. EDS analysis reveals that Y, Gd and Lu have been successfully doped into ZnMoO₄. In addition, the morphology of the phosphors is notably improved, exhibiting homogeneous dispersion morphology and irregular shapes of particle size ~ 0.5–1 µm. The luminescent intensity of (Zn,Ln_x)MoO₄:Tb³⁺ (Ln = Y³⁺, Gd³⁺ and Lu³⁺) phosphor is obviously higher than that of ZnMoO₄:Tb³⁺ phosphor. The energy transfer process between trivalent rare earth ions indicates that the inert earth ions can act as an energy bridge from MoO₄^2‐ to Tb³⁺. Copyright © 2013 John Wiley & Sons, Ltd.     

Intense green‐, red‐emitting Tb3+, Tb3+/Bi3+‐doped and Sm3+, Sm3+/La3+‐doped Ca2Al2SiO7 phosphors

This paper focuses on an optical study of a Tb³⁺/Bi³⁺‐doped and Sm³⁺/La³⁺‐ doped Ca₂Al₂SiO₇ phosphor synthesized using combustion methods. Here, Ca₂Al₂SiO₇:Sm³⁺ showed a red emission band under visible light excitation but, when it co‐doped with La³⁺ ions, the emission intensity was further enhanced. Ca₂Al₂SiO₇:Tb³⁺ shows the characteristic green emission band under near‐ultraviolet light excitation wavelengths, co‐doping with Bi³⁺ ions produced enhanced photoluminescence intensity with better colour tunable properties. The phosphor exhibited better phase purity and crystallinity, confirmed by X‐ray diffraction. Binding energies of Ca(2p), Al(2p), Si(2p), O(1s) were studied using X‐ray photoelectron spectroscopy. The reported phosphor may be a promising visible light excited red phosphor for light‐emitting diodes and energy conversion devices.     

Mechanoluminescence,thermoluminescence, photoluminescence studies on Ca3Y2Si3O12:RE3+ (RE3+ = Dy3+and Eu3+) phosphors

Dy³⁺ and Eu³⁺ activated Ca₃Y₂Si₃O₁₂ phosphors were synthesized by the solid‐state synthesis method. The phosphors were characterized by X‐ray diffraction (XRD), mechanoluminescence (ML), thermoluminescence (TL) and photoluminescence (PL) to determine structure and luminescence. For ML glow curves, only one peak was observed, as only one type of luminescence centre was formed during irradiation. The Ca₃Y₂Si₃O₁₂:Dy³⁺ TL glow curve showed a single peak at 151.55°C and the Ca₃Y₂Si₃O₁₂:Eu³⁺ TL glow curve peaked at 323°C with a small peak at 192°C, indicating that two types of traps were activated. The trapping parameters for both the samples were calculated using Chen's peak shape method. Dy³⁺‐activated Ca₃Y₂Si₃O₁₂ showed emission at 482 and 574 nm when excited by a 351 nm excitation wavelength, whereas the Eu³⁺‐activated Ca₃Y₂Si₃O₁₂ phosphor PL emission spectra showed emission peaks at 613 nm, 591 nm, 580 nm when excited at 395 nm wavelength. When excited at 466 nm, prominent emission peaks were observed at their respective positions with very slight shifts. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescence investigation of novel MgPbAl10O17:Tb3+ green‐emitting phosphor for solid‐state lighting

In this work, we studied the luminescence properties of Tb³⁺‐doped MgPbAl₁₀O₁₇ green phosphor. To understand the excitation mechanism and corresponding emission of the prepared phosphor, its structural, morphological and photoluminescence properties were investigated. In general, for green emission, Tb³ is used as an activator and the obtained excitation and emission spectra indicated that this phosphor can be effectively excited by a wavelength of 380 nm, and exhibits bright green emission centered at 545 nm corresponding to the f → f transition of trivalent terbium ions. The chromaticity coordinates were (C_x = 0.263, C_y = 0.723). The impact of Tb³⁺ concentration on the relative emission intensity was investigated, and the best doping concentration was found to be 2 mol%. This study suggests that Tb³⁺‐doped MgPbAl₁₀O₁₇ phosphor is a strong candidate for a green component in phosphor‐converted white light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Luminescent properties of Ca3SiO4Cl2 co‐doped with Ce3+ and Eu2+ for near‐ultraviolet light‐emitting diodes

Ca₃SiO₄Cl₂ co‐doped with Ce³⁺,Eu²⁺ was prepared by high temperature reaction. The structure, luminescent properties and the energy transfer process of Ca₃SiO₄Cl₂: Ce³⁺,Eu²⁺ were investigated. Eu²⁺ ions can give enhanced green emission through Ce³⁺ → Eu²⁺ energy transfer in these phosphors. The green phosphor Ca_2.9775SiO₄Cl₂:0.0045Ce³⁺,0.018Eu²⁺ showed intense green emission with broader excitation in the near‐ultraviolet light range. A green light‐emitting diode (LED) based on this phosphor was made, and bright green light from this green LED could be observed by the naked eye under 20 mA current excitation. Hence it is considered to be a good candidate for the green component of a three‐band white LED. Copyright © 2015 John Wiley & Sons, Ltd.     

Tunable emission,energy transfer and charge compensation in SrMoO4:Sm3+,Tb3+,Na+ phosphor

A series of SrMoO₄:Sm³⁺,Tb³⁺,Na⁺ phosphors was synthesized using a high‐temperature solid‐state reaction method in air. On excitation at 290 nm, SrMoO₄:Sm³⁺,Tb³⁺ phosphor emitted light that varied systematically from green to reddish‐orange on changing the Sm³⁺ and Tb³⁺ ion concentrations. The emission intensities of SrMoO₄:Sm³⁺ and SrMoO₄:Sm³⁺,Tb³⁺ phosphors were increased two to four times due to charge compensation when Na⁺ was added as a charge compensator. The luminescence mechanism and energy transfer could be explained using energy‐level diagrams of the MoO₄^2– group, Sm³⁺ and Tb³⁺ ions. SrMoO₄:Sm³⁺,Tb³⁺,Na⁺ could be used as reddish‐orange phosphor in white light‐emitting diodes (LEDs) based on an ~ 405 nm near‐UV LED chip. This research is helpful in adjusting and improving the luminescence properties of other phosphors. Copyright © 2015 John Wiley & Sons, Ltd.