Acetone-soluble cellulose acetates prepared by one-step homogeneous acetylation of cornhusk cellulose in an ionic liquid 1-allyl-3-methylimidazolium chloride (AmimCl)

Cellulose samples extracted from cornhusk have been successfully acetylated in an ionic liquid 1-allyl-3-methylimidazolium chloride (AmimCl). Without using any catalyst, cornhusk cellulose acetates (CCAs) with the degree of substitution (DS) in a range from 2.16 to 2.63 were prepared in one-step. Under the homogeneous state, the DS value of CCAs was easily controlled by the acetylation time. The obtained CCAs were characterized by means of FT-IR, ¹³C NMR, DSC, TGA, and a mechanical test. The NMR results showed that the distribution of the acetyl moiety among the three OH groups of the anhydroglucose unit shows a preference at the C₆ position. The CCAs exhibited good solubility in some organic solvents, such as acetone and DMSO. The cast CCA films from their acetone solutions had good mechanical properties. At the end of each acetylation of cornhusk cellulose, the ionic liquid AmimCl could be effectively recovered. Therefore, this study presents a promising approach and “green process” to make use of crop by-products.     

Synthesis of cellulose dehydroabietate in ionic liquid [bmim]Br

A new type of cellulose derivative, cellulose dehydroabietate (CDA), was synthesized by the O-acylation reaction of cellulose with dehydroabietic acid chloride (DHAC) using ionic liquid 1-butyl-3-methylimidazolium bromide ([bmim]Br) as a solvent and 4-dimethyl-aminopyridine (DMAP) as a catalyst. The resulting CDA was characterized by means of FT-IR, X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), and elemental analysis. Also, some properties of CDA were determined. These results showed that CDA has better solubility, water-repellency, and resistance to acids and bases than raw cellulose, and these properties increase with the DS of CDA.     

A facile preparation of gel materials from a solution of cellulose in ionic liquid

This paper reports a facile preparation of a flexible gel material from a solution of cellulose (15% w/w) in an ionic liquid of 1-butyl-3-methylimidazolium chloride by keeping it at room temperature for 7 days. Elemental analysis data indicated that the obtained gel material was composed of cellulose, the ionic liquid, and water. Both XRD and TGA results suggested that crystalline structure of cellulose was largely disrupted in the material. However, the existence of non-crystalline aggregates was assumed by the XRD data of the material. The gel material was probably obtained by the formation of cellulose aggregates in the solution, attributed to the gradual absorption of water. When the material was heated at 120 degrees C, it became soft, and converted into a fluid at 150 degrees C. By keeping the soft material at room temperature for 2 days, a gel material was regenerated, which was more transparent compared with the original material.     

Biocomposite films prepared from ionic liquid solutions of chitosan and cellulose

Blends of chitosan and cellulose were successfully produced using 1-butyl-3-methylimidazolium acetate (BMIMAc) as solvent media. Films were prepared from the blends by manually spreading the solution on a flat surface and precipitating the polymers in a mixture of methanol and water. To prevent the shrinkage of films, most of the absorbed water was removed by freeze drying under vacuum. Films prepared from the polymeric solutions were investigated by means of FT-IR, TGA, X-ray diffraction and SEM measurements. The shifting of the bands corresponding to -NH and CO groups of chitosan (FT-IR), the absence of the diffraction peaks at 2θ = 10.7 and 14.9° (XRD), the increased E_a for thermal decomposition for all the polymeric blends (MTGA), and the presence of an apparent homogeneous structure with no phase separation of the two polymers (SEM) provide evidence for the miscibility between chitosan and cellulose in the solid state.     

Antimicrobial surfaces of viologen-quaternized poly((2-dimethyl amino)ethyl methacrylate)-Si(100) hybrids from surface-initiated atom transfer radical polymerization

To improve the antimicrobial ability of silicon-based bioelectronics and to tailor the silicon surfaces for inhibiting biofilm formation, well-defined functional polymer-Si(100) hybrids, consisting of nearly monodispersed poly((2-dimethylamino)ethyl methacrylate) (P(DMAEMA)) covalently tethered on the silicon surface and functionalized by viologen moieties, were prepared. P(DMAEMA)-Si hybrids were prepared via surface-initiated atom transfer radical polymerization (ATRP) of (2-dimethylamino)ethyl methacrylate (DMAEMA) on the hydrogen-terminated Si(100) surfaces (Si−H surfaces). The tertiary amino groups of the covalently immobilized (Si−C bonded) P(DMAEMA) brushes on the silicon substrates were quaternized by an alkyl halide to produce a high concentration of quaternary ammonium groups with biocidal functionality. Alternatively, covalent coupling of viologen moieties to the tertiary amino groups of P(DMAEMA) brushes produced the quaternized P(DMAEMA)-Si(100) hybrids with substantially enhanced antimicrobial capability, as well as capability to effectively inhibit biofilm formation. Thus, the viologen-quaternized P(DMAEMA)-Si(100) hybrids possess good antibacterial surface properties and are potentially useful to the silicon-based bioelectronics to ensure their efficiency, durability and reliability.     

Collagen/cellulose hydrogel beads reconstituted from ionic liquid solution for Cu(II) adsorption

A novel adsorbent, biodegradable collagen/cellulose hydrogel beads (CCHBs), was prepared by reconstitution from a 1-butyl, 3-methylimidazolium chloride ([C₄mim]Cl) solution. The adsorption properties of the CCHBs for Cu(II) ion removal from aqueous solutions were investigated and compared with those of cellulose hydrogel beads (CHBs). The CCHBs have a three-dimensional macroporous structure whose amino groups are believed to be the main active binding sites of Cu(II) ions. The equilibrium adsorption capacity (q_e) of the CCHBs is greatly influenced by the collagen/cellulose mass ratio, and steeply increases until the collagen/cellulose mass ratio exceeds 2/1. The maximum adsorption is obtained at pH 6. The q_e of Cu(II) ions increases with increased initial concentration of the solution. Based on Langmuir isotherms, the maximum adsorption capacity (q_m) of CCHB3 (collagen/cellulose mass ratio of 3/1) is 1.06 mmol/g. The CCHBs maintain good adsorption properties after the fourth cycle of adsorption–desorption.     

Dissolution of cellulose in phosphate-based ionic liquids

Two kinds of alkylimidazolium salts containing dimethyl phosphate or diethyl phosphate were obtained as room temperature ionic liquids synthesized by one step, and both of them have the ability to dissolve untreated cellulose. Especially, 1-ethyl-3-methylimidazolium diethylphosphonate ([EMIM]DEP) could obtain 4 wt% cellulose solution within 10 min under 90. The effects of dissolution temperature on cellulose dissolution time and degree of polymerization were investigated. As dissolution temperature increased, dissolution time was greatly reduced. Both the original and regenerated cellulose samples were characterized with wide-angle X-ray diffraction, thermogravimetric analysis and scanning electron micrograph. The results showed that the crystalline structure of cellulose was converted to cellulose II from cellulose I in native cellulose. It was also found that the regenerated cellulose had good thermal stability with [EMIM]DEP ionic liquid.     

The study of factors affecting the enzymatic hydrolysis of cellulose after ionic liquid pretreatment

Cellulose resource has got much attention as a promising replacement of fossil fuel. The hydrolysis of cellulose is the key step to chemical product and liquid transportation fuel. In this paper a serials of chloride, acetate, and formate based ionic liquids were used as solvents to dissolve cellulose. The cellulose regenerated from ILs was characterized by FTIR and X-ray powder diffraction. From the characterization and analysis, it was found that the original close and compact structure has changed a lot. After enzymatic hydrolysis, different kinds of ionic liquids (ILs) have different yields of the reducing sugar (TRS). They are 100%, 90.72%, and 88.92% from 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), 1-ethyl-3-methylimidazolium acetate ([EMIM][OAc]), 1-butyl-3-methylimidazolium formate ([BMIM][HCOO]) respectively after enzymatic hydrolysis at 50 °C for 5 h. The results indicated that the yields and the hydrolysis rates were improved apparently after ILs pretreatment comparing with the untreated substrates.     

Preparation of chitin/cellulose composite gels and films with ionic liquids

In this study, we performed preparation and characterizations of the chitin/cellulose composite gels and films using the two ionic liquids, 1-allyl-3-methylimidazolium bromide and 1-butyl-3-methylimidazolium chloride. First, chitin and cellulose were dissolved in each appropriate ionic liquid. Then, the two liquids were mixed in the desired ratios at 100 °C to give the homogeneous mixtures. The gels were obtained by standing the mixtures for 4 days. On the other hand, the films were obtained by casting the mixtures on glass plates, followed by soaking in water and drying. The obtained gels and films were characterized by XRD and TGA measurements. The mechanical properties of the gels and films were evaluated under compressive and tensile modes, respectively.     

Cellulose extraction from wood chip in an ionic liquid 1-allyl-3-methylimidazolium chloride (AmimCl)

In the present study, 1-allyl-3-methylimidazolium chloride (AmimCl), an ionic liquid (IL), was used to extract cellulose from pine, poplar, Chinese parasol, and catalpa wood chips. Results show that pine is the most suitable wood species for cellulose extraction with ILs. Its cellulose extraction rate can reach as high as 62% under optimized conditions and its cellulose content is as high as 85% when DMSO/water is used as the precipitant. The dissolution process can be clearly observed by hot stage optical microscopy, and the reaction time can be significantly reduced by microwave irradiation. ¹³C CP/MAS NMR, FTIR, XRD, and SEM were used to analyze the cellulose-rich extracts of pine. Results show that IL dissolves pine wood by destroying inter and intramolecular hydrogen bonds between lignocelluloses. The major component of pine extract is cellulose with a homogeneous and dense structure. After extraction, AmimCl can be easily recycled and reused.     

Homogeneous modification of cellulose with succinic anhydride in ionic liquid using 4-dimethylaminopyridine as a catalyst

Cellulose, extracted from sugarcane bagasse, was successfully succinylated in ionic liquid 1-buty-3-methylimidazolium (BMIMCl) using 4-dimethylaminopyridine (DMAP) as a catalyst. Parameters investigated included the mass ratio of DMAP/succinic anhydride in a range from 0% to 15%, reaction time (from 30 to 120 min), reaction temperature (from 60 to 110 °C). The succinylated cellulosic derivatives had a degree of substitution (DS) ranging from 0.24 to 2.34. It was found that the DS of succinylated cellulosic derivatives using DMAP as a catalyst was higher than that without any catalyst under the same reaction conditions. The products were characterized by FT-IR, solid-state CP/MAS ¹³C NMR, and thermal analysis. FT-IR and solid-state CP/MAS ¹³C NMR spectra showed that succinoylation occurred at C-6, C-2 and C-3 positions. The thermal stability of the succinylated cellulose decreased upon chemical modification.     

Homogeneous phase synthesis of cellulose carbamate silica hybrid materials using 1-n-butyl-3-methylimidazolium chloride ionic liquid medium

Cellulose carbamate silica hybrid materials can be prepared in 78–84% yield using the homogeneous phase reaction of 3-(triethoxysilyl)propyl isocyanate with cellulose dissolved in 1-n-butyl-3-methylimidazolium chloride ionic liquid and then using NH₄OH catalyzed hydrolysis of triethoxysilyl groups and the sol–gel process. New cellulose carbamate silica hybrid materials produced were characterized by elemental analysis, FT-IR, and TG-DTA. The hydrophilic affinity of these materials is shown to decrease with the degree of substitution of the cellulose hydroxyl groups with carbamate groups.     

Preparation and characterization of bionanocomposite fiber based on cellulose and nano-SiO2 using ionic liquid

Microcrystalline cellulose (MCC)/nano-SiO₂ composite fibers were processed from solutions in 1-allyl-3-methylimidazolium chloride (AMIMCl) by the method of dry-jet wet spinning. The oscillatory shear measurements demonstrated that the gel network formed above 10 wt% nano-SiO₂ and the complex viscosity increased with increasing nano-SiO₂. Remarkably, the shear viscosity of the nanofluids was even lower than solutions without nano-SiO₂ under high shear rates. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images revealed that well-dispersed particles exhibit strong interfacial interactions with cellulose matrix. Measurements on wide-angle X-ray diffraction (WAXD) indicated that the regenerated cellulose and nanocomposite fibers were the typical cellulose II crystalline form, which was different from the native cellulose with the polymorph of Type I. The tensile strength of the nanocomposite fibers was larger than that of pure cellulose fiber and showed a tendency to increase and then decrease with increasing nano-SiO₂. Furthermore, the nanocomposite fibers exhibited improved thermal stability.     

Homogeneous modification of sugarcane bagasse cellulose with succinic anhydride using a ionic liquid as reaction medium

The homogeneous chemical modification of sugarcane bagasse cellulose with succinic anhydride using 1-allyl-3-methylimidazolium chloride (AmimCl) ionic liquid as a reaction medium was studied. Parameters investigated included the molar ratio of succinic anhydride/anhydroglucose units in cellulose in a range from 2:1 to 14:1, reaction time (from 30 to 160min), and reaction temperature (between 60 and 110 degrees C). The succinylated cellulosic derivatives were prepared with a low degree of substitution (DS) ranging from 0.071 to 0.22. The results showed that the increase of reaction temperature, molar ratio of SA/AGU in cellulose, and reaction time led to an increase in DS of cellulose samples. The products were characterized by FT-IR and solid-state CP/MAS (13)C NMR spectroscopy, and thermal analysis. It was found that the crystallinity of the cellulose was completely disrupted in the ionic liquid system under the conditions given. The data also demonstrated that homogeneous modification of cellulose with succinic anhydride in AmimCl resulted in the production of cellulosic monoester. The thermal stability of the succinylated cellulose decreased upon chemical modification.     

Thermo-responsive porous membranes of controllable porous morphology from triblock copolymers of polycaprolactone and poly(N-isopropylacrylamide) prepared by atom transfer radical polymerization

Stimuli-responsive polymers are of crucial importance in the design of smart biomaterials. The thermo-responsive triblock copolymers of polycaprolactone (PCL) and poly( N-isopropylacrylamide) (P(NIPAAm)), or P(NIPAAm)- b-PCL- b- P(NIPAAm) copolymers, were synthesized in this work via atom transfer radical polymerization (ATRP). The P(NIPAAm)- b-PCL- b-P(NIPAAm) copolymers were cast by phase inversion in water into porous membranes with well-defined and uniformly distributed pores. The P(NIPAAm) content in the P(NIPAAm)- b-PCL- b- P(NIPAAm) copolymers and the temperature of the aqueous medium for phase inversion could be used to control the pore size and porosity of the membranes. The thermo-responsive characteristics of the membranes were illustrated in the controlled water uptake and temperature-dependent glucose transport through the membranes. These temperature-sensitive membranes with controllable morphology have potential applications in biomedical engineering, drug delivery, and tissue engineering.     

Preparation of a thermosensitive highly regioselective cellulose/N-isopropylacrylamide copolymer through atom transfer radical polymerization

Regioselective copolymerization of N-isopropylacrylamide (NIPAM) onto cellulose was achieved by atom transfer radical polymerization (ATRP) using a regioselectively modified 6- O-bromoisobutyryl-2,3-di- O-methyl cellulose macroinitiator. Varying the ratio of NIPAM to macroinitiator to ligand to transition metal in a Cu(I)Br/ N, N, N', N', N'-pentamethyldiethylenetriamine (PMDETA) catalyst system affected graft yield and degree of polymerization. ATRP proceeded to completion without any trace of the macroinitiator, and a degree of polymerization (DP) of polyNIPAM up to 46.3 was obtained. Increasing the DP of the NIPAM component increased both the thermal decomposition temperature and the glass transition temperature of the copolymer. The grafting of NIPAM also affected the solubility properties of the methylcellulose. The 6- O-polyNIPAM-2,3-di- O-methyl cellulose formed a stable suspension in water at room temperature and underwent a hydrophillic-to-hydrophobic transition and copolymer precipitation when the temperature was raised above 30 degrees C.     

Reversible swelling of the cell wall of poplar biomass by ionic liquid at room temperature

Time-resolved autofluorescence, Raman microspectroscopy, and scanning microprobe X-ray diffraction were combined in order to characterize lignocellulosic biomass from poplar trees and how it changes during treatment with the ionic liquid 1-n-ethyl-3-methylimidazolium acetate (EMIMAC) at room temperature. The EMIMAC penetrates the cell wall from the lumen, swelling the cell wall by about a factor of two towards the empty lumen. However, the middle lamella remains unchanged, preventing the cell wall from swelling outwards. During this swelling, most of the cellulose microfibrils are solubilized but chain migration is restricted and a small percentage of microfibrils persist. When the EMIMAC is expelled, the cellulose recrystallizes as microfibrils of cellulose I. There is little change in the relative chemical composition of the cell wall after treatment. The action of EMIMAC on the poplar cell wall at room temperature would therefore appear to be a reversible swelling and a reversible decrystallization of the cell wall.