Continuous production of ethanol by yeast "immobilized" in a membrane-contained fermentor

A dialysate-feed, immobilized-cell dialysis continuous fermentation system was investigated as a method of relieving product inhibition in the conversion of glucose to ethanol by cells of Saccharomyces cerevisiae ATCC 4126. The substrate was fed into a continuous dialysate circuit and then into a batch fermentor circuit via diffusion through the microporous membranes of an intermediate dialyzer. Simultaneously, product was withdrawn from the fermentor circuit through the dialyzer membranes into the dialysate circuit and out in the effluent. Since the fermentor was operated without an effluent, the cells essentially were immobilized and converted substrate to product by maintenance metabolism. Contrary to prior results with this novel system for the continuous fermentation of lactose to lactate by lactobacillus cells, a steady state of yeast cells in the fermentor did not occur initially but was obtained by the depletion of medium nitrogen and the prevention of cell breakage, although the substrate and product concentrations then became unsteady. The inherent advantages of the system was offset in the ethanol fermentation by relatively low productivity, which appeared to be limited by membrane permeability.     

Rapid ethanol fermentations using vacuum and cell recycle

Cell recycle and vacuum fermentation systems were developed for continuous ethanol production. Cell recycle was employed in both atmospheric pressure and vacuum fermentations to achieve high cell densities and rapid ethanol fermentation rates. Studies were conducted with Saccharomyces cerevisiae (ATCC No. 4126) at a fermentation temperature of 35°C. Employing a 10% glucose feed, a cell density of 50 g dry wt/liter was obtained in atmospheric-cell recycle fermentations which produced a fermentor ethanol productivity of 29.0 g/liter-hr. The vacuum fermentor eliminated ethanol inhibition by boiling away ethanol from the fermenting beer as it was formed. This permitted the rapid and complete fermentation of concentrated sugar solutions. At a total pressure of 50 mmHg and using a 33.4% glucose feed, ethanol productivities of 82 and 40 g/liter-hr were achieved with the vacuum system with and without cell recycle, respectively. Fermentor ethanol productivities were thus increased as much as twelvefold over conventional continuous fermentations. In order to maintain a viable yeast culture in the vacuum fermentor, a bleed of fermented broth had to be continuously withdrawn to remove nonvolatile compounds. It was also necessary to sparge the vacuum fermentor with pure oxygen to satisfy the trace oxygen requirement of the fermenting yeast.     

自絮凝颗粒酵母乙醇连续发酵耦合酵母回用工艺的研究

模拟现有酒精发酵行业普遍采用的多级发酵罐串联系统,建立了一套由三级串联操作的搅拌式发酵罐和两个沉降罐组成的反应器系统,以脱胚脱皮玉米粉双酶法制备的糖化液为发酵底物,培养基初始还原糖浓度为220g/L,添加(NH4)2HPO41.5g/L和KH2PO42.5g/L,以0.057h-1的恒定稀释速率流加,将自沉降浓缩后的酵母乳先后经活化和不活化两种方式处理并循环至第一级发酵罐,系统在两种操作条件下分别达到了拟稳态。实验结果表明活化处理对改善发酵工艺技术指标方面发挥了显著的作用,发酵终点乙醇浓度达到101g/L,还原糖和残总糖分别在3.2和7.7g/L左右,发酵系统的设备生产强度指标为5.77g/(L.h),与无酵母回用的搅拌式反应器系统中自絮凝颗粒酵母乙醇发酵工艺相比,提高了70%。     

自絮凝酵母SPSC01在组合反应器系统中酒精连续发酵的研究

建立了一套由四级磁力搅拌发酵罐串联组成、总有效容积4000mL的小型组合生物反应器系统 ,其中一级罐作为种子培养罐。以脱胚脱皮玉米粉双酶法制备的糖化液为种子培养基和发酵底物 ,进行了自絮凝颗粒酵母酒精连续发酵的研究。种子罐培养基还原糖浓度为100g L ,添加 (NH₄)₂HPO₄ 和KH₂PO₄ 各 20g L ,以0.017h^-1 的恒定稀释速率流加 ,并溢流至后续酒精发酵系统。发酵底物初始还原糖浓度 220g/L ,添加 (NH₄)₂HPO₄ 15g/L和KH₂PO₄2 5g/L ,流加至第一级发酵罐 ,稀释速率分别为 0.017、0.025、0.033、0.040和0.05 0h^-1。实验数据表明 ,自絮凝颗粒酵母在各发酵罐中呈部分固定化状态 ,在稀释速率0.040h^-1 条件下 ,发酵系统呈一定的振荡行为 ,其他四个稀释速率实验组均能够达拟稳态。当稀释速率不超过 0 0 33h^-1 ,流出末级发酵罐的发酵液中酒精浓度可以达到 12 % (V/V)以上 ,残还原糖和残总糖分别在 0 11%和 0 35 % h^-1,流出末级发酵罐的发酵液中酒精浓度可以达到12%（V/V）以上,残还原糖和残总糖分别在0.11%和0.35%（W/V）以下。在稀释速率为0.033h^-1时,计算发酵系统酒精的设备生产强度指标为3.32（g·L^-1·h^-1）,与游离酵母细胞传统酒精发酵工艺相比,增加约1倍。     

Ethanol fermentation in a yeast immobilized tubular fermentor

In this article, a mathematical model describing the kinetics of ethanol fermentation in a whole cell immobilized tubular fermentor is proposed. Experimental results show reasonable agreement with the proposed model. A procedure for treating the fermentation data for determining the ethanol inhibition constants k(1) and k(2) is described. The ethanol productivity of the immobilized cell fermentor is compared with those of traditional fermentors. Experimental studies indicate that with Saccharomyces cerevisiae (NRRL Y132) culture, ethanol productivity in the range 21.2-83.7 g ethanol L(-1) h(-1) at ethanol concentration of 76-60 g/L can be achieved. This is comparable to or higher than those reported in the literature for yeast. The product yield factor of 0.5 g ethanol/g glucose was obtained. The immobilized cell fermentor does not show washout at dilution rates of 7 h(-1) and shows good stability over a 650-h operating period.     

Batch and continuous solid-phase fermentation of Jerusalem artichoke tubers

Two strains of Kluyveromyces marxianus were evaluated for their ability to ferment Jerusalem artichoke tuber pulp to ethanol under pH levels ranging from 2.0–6.3. Bacterial contamination was prevented in batch, solid-phase fermentation when pulp was initially adjusted to pH 3.5 or less, and maximal yeast populations occurred at pH 3.0–3.5. Fermentation times were also shortest for both yeast (13–18 h) and ethanol (48–64 h) production when pulp pH was in this range. However, ethanol yields (41–53% of theoretical) and fermentation efficiencies (68–78%) were somewhat lower than expected, with only 6.6–7.2% (v/v) ethanol produced by strain Y-1598 and 5.7–6.9% produced by strain Y-1550. Based on these parameters, the continuous solid-phase fermentor was operated for 396 h using strain Y-1598. The pH of pulp entering the fermentor was adjusted to 2.5 to compensate for partial neutralization by the mild steel of the fermentor. This resulted in fermenting pulp with a pH of 3.0–3.5, and therefore no contamination. Pulp exiting the fermentor after 72 h contained 6.9 × 10⁸ yeast cells/ml and 7.3% ethanol, which represented 55.9% of the theoretical yield and a fermentation efficiency of 73.3%. Further modifications (partial acid hydrolysis, finer grinding, etc.) should permit higher yields.     

Semicontinuous diffusion fermentation of fodder beets for fuel ethanol and cubed protein feed production

A novel, semicontinuous diffusion fermentation system was used to produce fuel ethanol and a cubed protein feed (CPF) from fodder beets at an intermediate scale. In the process, fodder beet cubes were augered diagonally upward against a flow of 0.26N H(2)SO(4) and yeast in a tubular fermentor. Exiting one end of the fermentor was CPF, while fermented beer [6-9% (v/v) ethanol] exited the other end. Retention times for beer and CPF were 264 and 72 h, respectively. Contamination was controlled by maintaining the fermentation pH between 2.1 and 2.6 using H(2)SO(4). Production costs for a greatly scaled-up (times 1400) conceptual version of this system (using a continuous rather than a semicontinuous processing mode) were projected by calculation to be $0.529/L for 95% ethanol (net of a $0.112/L credit for CPF). The calculated energy balance (energy output-energy input ratio) was estimated to be 3.04. In calculating the energy balance, the output energy of the CPF and input energy for growing the fodder beets were not included. A design for the scaled-up plant is provided.     

Continuous ethanol production from sugar beet molasses using an osmotolerant mutant strain of Zymomonas mobilis

A laboratory process was established for ethanol production by fermentation of sugar beet molasses with the bacterium Zymomonas mobilis. Sucrose in the molasses was hydrolyzed enzymatically to prevent levan formation. A continuous system was adopted to reduce sorbitol formation and a two-stage fermentor was used to enhance sugar conversion and the final ethanol concentration. This two-stage fermentor operated stably for as long as 18 d. An ethanol concentration of 59.9 g/l was obtained at 97% sugar conversion and at high ethanol yield (0.48 g/g, 94% of theoretical). The volumetric ethanol productivity (3.0 g/l·h) was superior to that of batch fermentation but inferior to that of a single-stage continuous system with the same medium. However, the thanol concentration was increased to a level acceptable for economical recovery. The process proposed in this paper is the first report of successful fermentation of sugar beet molasses in the continuous mode using the bacterium Z. mobilis.     

Cell retention culture with an internal filter module: continuous ethanol fermentation

A new internal filter feedback system with a stainless steel filter was introduced and its application for continuous ethanol fermentation was investigated. The filter performance was highly influenced by agitation speed and yeast concentration. Retention coefficient with a filter of 2 mum pore size was found more than 97.5%, and the filter was suitable for yeast separation. Maximum yeast concentration was 157 g/L and the best operable cell concentration was between 90 and 150 g/L. Which was similar to that obtained in the external membrane cell recycle culture. The cell concentration in the fermentor was maintained by manipulation of dilution rate and bleed ratio with the growth rate. The internal filter feedback system was successfully operated for more than 10 days. This study shows that the internal filter feedback system with a stainless steel filter can be used high-density cell culture and ethanol fermentation. Furthermore, it can be scaled up more easily than the external cell recycle system. (c) 1993 John Wiley & Sons, Inc.     

自絮凝酵母高浓度重复批次乙醇发酵

利用发酵性能优良的自絮凝酵母Saccharomyces cerevisiaeflo,研究开发了重复批次高浓度乙醇发酵系统,以节省下游加工过程的能耗。在终点乙醇浓度达到120g/L左右的条件下,发酵系统的乙醇生产强度达到8.2g/(L·h)。然而实验中发现,随着发酵批次的增多,自絮凝酵母沉降性能逐渐下降,从发酵液中沉降分离所需时间相应延长,导致发酵液中高浓度乙醇对酵母的毒害作用加剧,影响其发酵活性和发酵系统运行的稳定性,发酵装置运行11个批次后无法继续运行。实验结果表明,絮凝能力下降导致的酵母絮凝颗粒尺度减小是其沉降性能下降的主要原因。进一步研究发现,酵母的絮凝能力通过再培养可以恢复。在此基础上对发酵系统操作进行改进,每批发酵结束后可控采出一定比例菌体,调节系统的酵母细胞密度和乙醇生产强度以刺激酵母增殖,保持其絮凝能力。在达到相同发酵终点乙醇浓度条件下,虽然发酵系统的乙醇生产强度降低到4.0g/(L·h),但运行10d后絮凝颗粒酵母尺度趋于稳定,继续运行14d,未发现絮凝颗粒酵母尺度继续下降的现象,系统可以稳定运行。     

Simultaneous saccharification and continuous fermentation of sludge-containing mash for bioethanol production by Saccharomyces cerevisiae CHFY0321

A continuous process was employed to improve the volumetric productivity of bioethanol production from cassava mash containing sludge and to simplify the process of ethanol production from cassava. After raw cassava powder was liquefied, it was used directly in a continuous process without sludge filtration or saccharification. A fermentor consisting of four linked stirrer tanks was used for simultaneous saccharification and continuous fermentation (SSCF). Although the mash contained sludge, continuous fermentation was successfully achieved. We chose the dilution rate on the basis of the maximum saccharification time; the highest volumetric productivity and ethanol yield were observed at a dilution rate of 0.028 h?1. The volumetric productivity, final ethanol concentration, and % of theoretical ethanol yield were 2.41 g/Lh, 86.1g/L, and 91%, respectively. This SSCF process using the self-flocculating yeast Saccharomyces cerevisiae CHFY0321 illustrates the possibility of realizing cost-effective bioethanol production by eliminating additional saccharification and filtration processes. In addition, flocculent CHFY0321, which our group developed, showed excellent fermentation results under continuous ethanol production.     

Ethanol production in a continuous fermentation/membrane pervaporation system

The productivity of ethanol fermentation processes, predominantly based on batch operation in the U.S. fuel ethanol industry, could be improved by adoption of continuous processing technology. In this study, a conventional yeast fermentation was coupled to a flat-plate membrane pervaporation unit to recover continuously an enriched ethanol stream from the fermentation broth. The process employed a concentrated dextrose feed stream controlled by the flow rate of permeate from the pervaporation unit via liquid-level control in the fermentor. The pervaporation module contained 0.1 m² commercially available polydimethylsiloxane membrane and consistently produced a permeate of 20%–23% (w/w) ethanol while maintaining a level of 4%–6% ethanol in a stirred-tank fermentor. The system exhibited excellent operational stability. During continuous operation with cell densities of 15–23 g/l, ethanol productivities of 4.9–7.8 gl^–1 h^–1 were achieved utilizing feed streams of 269–619 g/l glucose. Pervaporation flux and ethanol selectivities were 0.31–0.79 lm^–2 h^–1 and 1.8–6.5 respectively.     

Ethanol production from xylose with the yeast Pichia stipitis and simultaneous product recovery by gas stripping using a gas-lift loop fermentor with attached side-arm (GLSA)

The bioconversion of xylose into ethanol with the yeast Pichia stipitis CBS 5773 is inhibited when 20 g/L of ethanol are present in the fermentation broth. In order to avoid this limitation, the fermentation was carried out with simultaneous recovery of product by CO(2) stripping. The fermentation was also improved by attaching a side-arm to the main body of a classical gas-lift loop fermentor. This side-arm increases the liquid circulation, mass transfer, and gas distribution, reducing the amount of oxygen in the inlet gas necessary to perform the fermentation of xylose under microaerobic conditions (K(L)a approximately 16 h(-1)). The continuous stripping of ethanol from the fermentation broth in this new bioreactor system allowed the consumption of higher xylose concentrations than using Erlenmeyer shaker flasks, improved significantly the process productivity and provided a clean ethanol solution by using an ice-cooled condenser system. Finally, a fed-batch fermentation was carried out with a K(L)a = 15.8 h(-1). Starting with 248.2 g of xylose, 237.6 g of xylose was consumed to produce 88.1 g of ethanol which represents 72.6% of the theoretical yield (47.2 g/L of ethanol was recovered in the condenser, while 9.6 g/L remained in the fermentation broth).     

Film fermentor for ethanol production by yeast immobilized on cotton cloth

Summary Saccharomyces cerevisiae cells were immobilized on cotton cloth. The resulting yeast films were placed in parallel in a rectangular fermentor which was designed for scale-up. Ethanol production from sugars in the hydrolysate of Jerusalem artichoke tubers was studied in three modes of operation: batch, circulated batch and continuous flow. Circulated batch fermentation gave the shortest time of fermentation and accordingly the highest average ethanol productivity.     

Kinetics of ethanol production by baker's yeast in an integrated process of fermentation and microfiltration

The productivity of a fermentation is proportional to the biomass concentration. The productivity can therefore be increased by retention of the cells in the fermentor. In this study microfiltration was used for cell retention in a fermentation of glucose to ethanol by baker's yeast. Compared to a system without cell retention the productivity could be increased 12-fold to 55 kg/m³ h at a biomass concentration of 135 kg/m³. Maximal ethanol concentrations of 76 kg/m³ were obtained at conditions of growth. At zero growth conditions in the integrated system the ethanol concentration could be increased to about 115 kg/m³, and could be produced for at least 10 hours. The fermentation results in the integrated system could be described reasonably well with a mathematical model based on a different linear inhibition kinetics for growth and substrate consumption.     

The rotorfermentor. II. Application to ethanol fermentation.

The kinetics of microbial growth and product formation are described as applied to the high cell concentration scheme of the rotorfermentor. A bench scale pilot plant was designed and built in order to demonstrate the operational feasibility of the rotorfermentor. The fermentation of glucose to ethanol by Saccharomyces cerevisiae ATCC 4126 was used. When the rotorfermentor was used with a glucose feed concentration of 104 g/liter almost 100% glucose utilization was obtained and the ethanol productivity rate was 27.3 g ethanol/liter hr which was found to be about 10 times greater than the ethanol productivity obtained from an ordinary continuous stirred tank (CST) fermentor. The ethanol experimental results obtained from the rotorfermentor and an ordinary CST fermentor were used as a basis to assess the economic feasibility of the rotorfermentor. The economics of an industrial scale ordinary CST fermentor with and without cell recycle is compared with a rotorfermentor unit for the same ethanol production throughput. For the process conditions considered in this case, calculations showed that the rotorfermentor may replace both a CST fermentor and cell centrifuge resulting in lower capital equipment costs and lower power consumption requirements.     

Mathematical model of microporous hollow-fiber membrane extractive fermentor

A mathematical model is presented for a microporous hollow-fiber membrane extractive fermentor (HFEF). The model is based on the continuous flow of the aqueous nutrient phase and cells through the shell space of the fermentor where the fermentation reaction occurs. The product diffuses from the shell space through the hollow-fiber membrane where it is continuously removed by solvent flowing concurrently through the fiber lumen. Results for ethanol production show that the HFEF has a volumetric productivity significantly higher than that possible using conventional methods. The model predicts the existence of an optimum volume fraction of hollow fibers in the fermentor that maximizes the total volumetric productivity. This optimum is the result of a classic trade-off between the volume fraction of the fermentor required for fermentation and that required for efficient removal of the ethanol product to minimize product inhibition.     

Continuous ethanol production by immobilized yeast reactor coupled with membrane pervaporation unit

A system comprised of an immobilized yeast reactor producing ethanol, with a membrane pervaporation module for continuously removing and concentrating the produced ethanol, was developed. The combined system consisted of two integrated circulation loops: In one the sugar-containing medium is circulated through the membrane pervaporation module. The two loops were interconnected in a way allowing for separate parameter optimization (e.g., flow rate, temperature, pH) for each loop.The fermentation unit was 2.0 L bioreactor with five equal segments, packed with 5-mm beads of immobilized yeasts. The bead matrix was a crosslinked polyacrylamide hydrazide gel coated with calcium alginate. The fast circulation loop of the bioreactor allowed for efficient liberation of CO(2) at the top of the immobilized yeast reactor. Continuous operation of the uncoupled reactor for over 50 days with inflowing defined medium or dilute molasses at a residence time of 1.25 h yielded ethanol at a rate of about 10 g/L h.The pervaporation unit was constructed from four 60-cm-long tubular membranes of silicone composite on a polysulfone support. The output from the fermentor was circulated through the inside of the tubes of a unit with a total surface area of 800 cm(2), having an average flux of 150 mL/h, and selectivities to ethanol vs. water up to 7. A vacuum of 30 mb was applied to the outside of the tubes, removing 20-30 g of ethanol per hour, which was collected in condensors. The continuous removal of ethanol, avoiding inhibition of the fermentation process, resulted in an improved productivity and allowed the use of high sugar concentrations (40% wt/vol) offering the potential of a compact system with reduced stillage.The combined system of ethanol production and removal enabled an operative steady state at which the liquid volume of the system, and the concentrations of ethanol within the reactor ( 4% wt/vol), as well as within the flux crossing the pervaporation membrane (17%-20% wt/vol) were kept constant. At the steady state, a 40% wt/vol sugar solution could be continuously added to the fermentor when 12%-20% wt/vol clear ethanol solution was continuously removed by the pervaporation unit. Membrane fouling was reversed by short washing steps, and continuous step operation was maintained by working with two different modules that were interchanged. In this manner, long term continuous operation (over 40 days) was achieved with a productivity of 20-30 g/L h, representing over a twofold increase relative to the continuously operated reactor uncoupled from the membrane and a fivefold increase in comparison with the value obtained fro a corresponding batch fermentation.     

Application of multistage continuous fermentation for production of fuel alcohol by very-high-gravity fermentation technology

A fermentation system to test the merging of very-high-gravity (VHG) and multistage continuous culture fermentation (MCCF) technologies was constructed and evaluated for fuel ethanol production. Simulated mashes ranging from 15% to 32% w/v glucose were fermented by Saccharomyces cerevisiae and the dilution rates were adjusted for each glucose concentration to provide an effluent containing less than 0.3% w/v glucose (greater than 99% consumption of glucose). The MCCF can be operated with glucose concentrations up to 32% w/v, which indicates that the system can successfully operate under VHG conditions. With 32% w/v glucose in the medium reservoir, a maximum of 16.73% v/v ethanol was produced in the MCCF. The introduction of VHG fermentation into continuous culture technology allows an improvement in ethanol productivity while producing ethanol continuously. In comparing the viability of yeast by methylene blue and plate count procedures, the results in this work indicate that the methylene blue procedure may overestimate the proportion of dead cells in the population. Ethanol productivity (Yps) increased from the first to the last fermentor in the sequence at all glucose concentrations used. This indicated that ethanol is more effectively produced in later fermentors in the MCCF, and that the notion of a constant Yps is not a valid assumption for use in mathematical modeling of MCCFs. Journal of Industrial Microbiology & Biotechnology (2001) 27, 87–93. Received 20 January 2001/ Accepted in revised form 28 April 2001     

Rapid ethanol fermentation of cellulose hydrolysate. I. Batch versus continuous systems

Rapid fermentation of bagasse hydrolysate to ethanol under anaerobic conditions by a strain of Saccharomyces cerevisiae has been studied in batch and continuous cultures at pH 4.0 and 30°C temperature with cell recycle. By using a 23.6 g/liter cell concentration, a concentation of 9.7% (w/v)ethanol was developed in a period of 6 hr. The rate of fermentation was found to increase with supplementation of yeast vitamins in the hydrolysate. In continuous culture employing cell recycle and a 0.127 v/v/m air flow rate, a cell mass concentration of 48.5 g/liter has been achieved. The maximum fermentor productivity of ethanol obtained under these conditions was 32.0 g/liter/hr, which is nearly 7.5 times higher than the normal continuous process without cell recycle and air sparging. The ethanol productivity was found to decrease linearly with ethanol concentration. Conversion of glucose in the hydrolysate to ethanol was achieved with a yield of 95 to 97% of theoretical.