Preparation and characterization of bio-diesels from various bio-oils

Methyl, ethyl, 2-propyl and butyl esters were prepared from canola and linseed oils through transesterification using KOH and/ or sodium alkoxides as catalysts. In addition, methyl and ethyl esters were prepared from rapeseed and sunflower oils using the same catalysts. Chemical composition of the esters was determined by HPLC for the class of lipids and by GC for fatty acid compositions. The bio-diesel esters were characterized for their physical and fuel properties including density, viscosity, iodine value, acid value, cloud point, pure point, gross heat of combustion and volatility. Methyl and ethyl esters prepared from a particular vegetable oil had similar viscosities, cloud points and pour points, whereas methyl, ethyl, 2-propyl and butyl esters derived from a particular vegetable oil had similar gross heating values. However, their densities, which were 2 7% higher than those of diesel fuels, statistically decreased in the order of methyl approximately 2-propyl > ethyl > butyl esters. Butyl esters showed reduced cloud points (-6 degrees C to -10 degrees C) and pour points (-13 degrees C to -16 degrees C) similar to those of summer diesel fuel having cloud and pour points of -8 degrees C and -15 degrees C, respectively. The viscosities of bio-diesels (3.3-7.6 x 10(-4) Pa s at 40 degrees C) were much less than those of pure oils (22.4-45.1 x 10(-4) Pa s at 40 degrees C) and were twice those of summer and winter diesel fuels (3.50 and 1.72 x 10(-4) Pa s at 40 degrees C), and their gross heat contents of approximately 40 MJ/kg were 11% less than those of diesel fuels (approximately 45 MJ/kg). For different esters from the same vegetable oil, methyl esters were the most volatile, and the volatility decreased as the alkyl group grew bulkier. However, the bio-diesels were considerably less volatile than the conventional diesel fuels.     

Influence of fatty acid methyl esters from hydroxylated vegetable oils on diesel fuel lubricity

Current and future regulations on the sulfur content of diesel fuel have led to a decrease in lubricity of these fuels. This decreased lubricity poses a significant problem as it may lead to wear and damage of diesel engines, primarily fuel injection systems. Vegetable oil based diesel fuel substitutes (biodiesel) have been shown to be clean and effective and may increase overall lubricity when added to diesel fuel at nominally low levels. Previous studies on castor oil suggest that its uniquely high level of the hydroxy fatty acid ricinoleic acid may impart increased lubricity to the oil and its derivatives as compared to other vegetable oils. Likewise, the developing oilseed Lesquerella may also increase diesel lubricity through its unique hydroxy fatty acid composition. This study examines the effect of castor and Lesquerella oil esters on the lubricity of diesel fuel using the High-Frequency Reciprocating Rig (HFRR) test and compares these results to those for the commercial vegetable oil derivatives soybean and rapeseed methyl esters.     

Determination of double bond positions in fatty acids with conjugated double bonds

The positions of the double bonds in fatty acids with conjugated double bonds may be determined by mass spectrometry of the methyl esters of their trimethylsilyl ether derivatives obtained by hydroxylation of the double bonds followed by silylation of the resulting polyols. The method has been applied to trans-9,trans-11- and trans-10, trans-12-octadecadienoic acid.     

Improved method for determination of the position of double bonds in polyenoic fatty acid esters

An improved method is described for determination of the position of double bonds in polyenoic fatty acid methyl esters. Partial reduction with hydrazine is employed without prior hydrolysis to the free fatty acid, and the resulting monoenes are identified by reductive ozonolysis.     

13C-NMR of double and triple bond carbon atoms of unsaturated fatty acid methyl esters

The carbon magnetic resonance spectra of many fatty acid methyl esters with cis and trans double bonds and triple bonds at various positions and in many different combinations have been investigated.The influence of the ester group on double and triple bonds in the fatty acid chain depends strongly on the positions of these bonds. For a given position the influence is constant, even if one or more other double or triple bonds are present.Together with the evaluated chemical shift parameters for the effects of double and triple bonds on each other, complete assignments are possible and spectra of various types of unsaturated esters can be predicted with high accuracy (±0.1 ppm).     

The PMR analysis of non-conjugated alkenoic and alkynoic acids and esters.

The 220 MHz PMR spectra of 143 non-conjugated alkenoic and alkynoic acids and esters are correlated so as to provide a method for the structural analysis of such compounds in general. The spectral data are explained in terms of long-range deshielding of the double bonds, triple bonds, acid and ester groups in the molecules, and parameters are derived to quantify the influence of these groups on the chemical shifts of methyl and methylene protons up to six carbon atoms distant along an alkyl chain. It is shown that, by the application of these parameters, 220 MHz PMR spectroscopy can be used to determine both the stereochemistry and position of double bonds, and the position of triple bonds, in the majority of fatty acids and esters. The 2- to 9- and 13- to 17-cis- and trans-isomers of octadecenoic acid may be readily idenfited in this way, whilst for the octadecynoic acids all positional isomers may be characterized. Examples are also given of the structural analysis of several polyenoic compounds, including methyl cis-5, cis-8, cis-11, cis-14, cis-5, cis-8, cis-11, trans-14, and trans-5, cis-8, cis-11, cis-14-eicosatetraenoates, and methyl trans-5, cis-9, cis-12-octadecatrienoate.     

Raman studies of some diunsaturated olefinic and acetylenic fatty acids and their derivatives.

The Raman spectra of CCl4 solutions of the 6,12; 7,12; 8,12; 9,12; and 10,12 isomers of octadecadiynoic acid and of the octadecadienoic acid methyl esters of both the cis,cis and trans,trans series are reported. Provided that there are two or more methylene groups between the unsaturated groups, the double and triple bond vibrational wavenumber values are close to those found in monounsaturated derivatives. An attempt has been made to obtain a correlation between the relative intensities of the nu(CequalsC) and delta(CH2) bands and the ratio of the number of double bonds to methylene groups in the molecule.     

Monoepoxy octadecadienoates and monoepoxy octadecatrienoates 1: NMR spectral characterization

Methyl esters of gamma-linolenic acid, alpha-linolenic acid and stearidonic acid were epoxidised using m-chloroperbenzoic acid to achieve nine cis-monoepoxy-C18 fatty acid methyl esters (FAMEs), including novel methyl cis-monoepoxy derivatives of stearidonic acid and a cis-6,7-epoxy derivative of gamma-linolenic acid. These nine monoepoxy FAMEs were purified by normal-phase HPLC, identified by LC-MS, 1H and 13C NMR, and characterized by mass spectrometry and NMR spectroscopy. This study is focused on structural characterization of these C18 monoepoxy FAMEs using techniques in NMR spectroscopy including 1H, 13C, 1H-1H correlated spectroscopy (COSY) and 1H-13C heteronuclear correlation (HETCOR). The proton and carbon NMR chemical shifts of the epoxide, the double bonds, and the interrupted methylenes are assigned. Also discussed is an interpretation of the 1H and 13C NMR spectra of these monoepoxides including the changes in the 13C resonance of the olefinic carbons on the neighboring double bonds resulting from epoxide formation.     

Correlation for the estimation of the density of fatty acid esters fuels and its implications. A proposed Biodiesel Cetane Index

Biodiesel fuels (methyl or ethyl esters derived from vegetables oils and animal fats) are currently being used as a means to diminish the crude oil dependency and to limit the greenhouse gas emissions of the transportation sector. However, their physical properties are different from traditional fossil fuels, this making uncertain their effect on new, electronically controlled vehicles. Density is one of those properties, and its implications go even further. First, because governments are expected to boost the use of high-biodiesel content blends, but biodiesel fuels are denser than fossil ones. In consequence, their blending proportion is indirectly restricted in order not to exceed the maximum density limit established in fuel quality standards. Second, because an accurate knowledge of biodiesel density permits the estimation of other properties such as the Cetane Number, whose direct measurement is complex and presents low repeatability and low reproducibility. In this study we compile densities of methyl and ethyl esters published in literature, and proposed equations to convert them to 15 °C and to predict the biodiesel density based on its chain length and unsaturation degree. Both expressions were validated for a wide range of commercial biodiesel fuels. Using the latter, we define a term called Biodiesel Cetane Index, which predicts with high accuracy the Biodiesel Cetane Number. Finally, simple calculations prove that the introduction of high-biodiesel content blends in the fuel market would force the refineries to reduce the density of their fossil fuels.     

Influence of fatty acid composition of raw materials on biodiesel properties

The aim of this work was the study of the influence of the raw material composition on biodiesel quality, using a transesterification reaction. Thus, ten refined vegetable oils were transesterificated using potassium methoxide as catalyst and standard reaction conditions (reaction time, 1h; weight of catalyst, 1 wt.% of initial oil weight; molar ratio methanol/oil, 6/1; reaction temperature, 60 degrees C). Biodiesel quality was tested according to the standard [UNE-EN 14214, 2003. Automotive fuels. Fatty acid methyl esters (FAME) for diesel engines. Requirements and test methods]. Some critical parameters like oxidation stability, cetane number, iodine value and cold filter plugging point were correlated with the methyl ester composition of each biodiesel, according to two parameters: degree of unsaturation and long chain saturated factor. Finally, a triangular graph based on the composition in monounsaturated, polyunsaturated and saturated methyl esters was built in order to predict the critical parameters of European standard for whatever biodiesel, known its composition.     

Tritioboration and synthesis of tritium-labeled polyunsaturated fatty acids

Methyl esters of polyunsaturated fatty acids labeled with tritium were prepared by partial stereoselective reduction of the corresponding acetylenic esters with tritiated disiamylborane, followed by protonolysis with tritiated acetic acid. The labeling was strictly specific, and the tritium atoms were located only at the carbon atoms forming the unsaturated bond(s). Synthesis of some tritiated fatty acid methyl esters with methylene-interrupted trans-cis double bonds is also reported.     

Lumenal hydrolysis of menhaden and rapeseed oils and their fatty acid methyl and ethyl esters in the rat

Simple alkyl (ethyl) esters of polyunsaturated fish oil fatty acids have been proposed as dietary supplements, but their relative efficiency of digestion and absorption have not been determined. Using stomach tubes, we gave rats menhaden or rapeseed oils, or the corresponding methyl and ethyl esters, and determined by chromatographic methods the lipid classes and molecular species recovered from the lumen of the jejunum during the first 1 to 2.5 h of digestion. Hydrolysis of menhaden oil resulted in a preferential retention of a high proportion of the polyunsaturated long chain acids in the sn-2-monoacylglycerols and in the residual triacyglycerols, while digestion of rapeseed oil led to a preferential release of free long chain monounsaturated fatty acids. In contrast, hydrolysis of the alkyl (methyl and ethyl) esters of the fatty acids of either menhaden or rapeseed oil resulted in a composition of free fatty acids which was much more representative of the original esters. It was therefore concluded that the differential lumenal liberation of the long chain and polyunsaturated (three or more double bonds) fatty acids from fish and rapeseed oil is largely due to their characteristic distribution between the primary and secondary positions in the glycerol molecule, and to a much lesser extent to a chain length discrimination by pancreatic lipase. This study also shows that the methyl and ethyl esters are hydrolyzed about 4 times more slowly than the corresponding triacylglycerols, which is sufficient to maintain a saturated micellar solution of fatty acids in the intestinal lumen during absorption.     

Construction of combustion models for rapeseed methyl ester bio-diesel fuel for internal combustion engine applications

Bio-diesel fuels are non-petroleum-based diesel fuels consisting of long chain alkyl esters produced by the transesterification of vegetable oils, that are intended for use (neat or blended with conventional fuels) in unmodified diesel engines. There have been few reports of studies proposing theoretical models for bio-diesel combustion simulations. In this study, we developed combustion models based on ones developed previously. We compiled the liquid fuel properties, and the existing detailed mechanism of methyl butanoate ester (MB, C₅H₁₀O₂) oxidation was supplemented by sub-mechanisms for two proposed fuel constituent components, C₇H₁₆ and C₇H₈O (and then, by mp2d, C₄H₆O₂ and propyne, C₃H₄) to represent the combustion model for rapeseed methyl ester described by the chemical formula, C₁₉H₃₄O₂ (or C₁₉H₃₆O₂). The main fuel vapor thermal properties were taken as those of methyl palmitate C₁₉H₃₆O₂ in the NASA polynomial form of the Burcat database. The special global reaction was introduced to “crack” the main fuel into its constituent components. This general reaction included 309 species and 1472 reactions, including soot and NO_x formation processes. The detailed combustion mechanism was validated using shock-tube ignition-delay data under diesel engine conditions. For constant volume and diesel engine (Volvo D12C) combustion modeling, this mechanism could be reduced to 88 species participating in 363 reactions.     

Application of catalytic ozone chemistry for improving biodiesel product performance

Ozonolysis of methyl soyate (biodiesel) was conducted in the presence of methanol, dichloromethane (solvent), and triethylamine (catalyst) at -75 degrees C. Structural analysis, including FTIR, GC, and GC-MS, showed that the total amount of double bonds in the mixture was reduced by more than 90% after 2 h of ozonolysis. All of the esters predicted by this novel application of ozone reaction chemistry were successfully produced. Other major components were identified by GC-MS. Thermogravimetric analysis showed a dramatic decrease in the onset volatilization temperature from 135 to 73 degrees C, making ozonated biodiesel fuel comparable to diesel fuel (76 degrees C). Differential scanning calorimetric studies showed that the cooling curves for both methyl soyate and ozonated methyl soyate displayed two exothermic regions. The onset freezing temperature of ozonated methyl soyate in the "colder" region was significantly reduced from -63 to -86 degrees C. Furthermore, the degree of crystallinity in the "hotter" region was also reduced.     

13C-NMR of methyl,methylene and carbonyl carbon atoms of methyl alkenoates and alkynoates

The carbon magnetic resonance spectra of 102 fatty acid methyl esters with cis and trans double bonds and triple bonds at various positions and in many different combinations have been investigated. A comprehensive set of chemical shift parameters has been developed for the various substituents. With the aid of these parameters, the chemical shifts of all methyl, methylene carbonyl carbon atoms can be predicted with an accuracy of ±0.1 ppm or better.     

Biodegradation of diesel/biodiesel blends by a consortium of hydrocarbon degraders: effect of the type of blend and the addition of biosurfactants

Biodegradation experiments for diesel/biodiesel blends in liquid cultures by-petroleum degrading microbial consortium showed that for low amendments of biodiesel (10%) the overall biodegradation efficiency of the mixture after seven days was lower than for petroleum diesel fuel. Preferential usage of methyl esters in the broad biodiesel concentration range and diminished biodegradation of petroleum hydrocarbons for 10% biodiesel blend was confirmed. Rhamnolipids improved biodegradation efficiency only for blends with low content of biodiesel. Emulsion formation experiments showed that biodiesel amendments significantly affected dispersion of fuel mixtures in water. The presence of rhamnolipids biosurfactant affected stability of such emulsions and altered cell surface properties of tested consortium.     

Effect of growth stage on mycolic acid structure in cell walls of Nocardia asteroides GUH-2

Mycolic acids were extracted from the cell walls of Nocardia asteroides GUH-2 during different phases of growth at 37 degrees C. These were subjected to structural analysis by combining thin-layer chromatography and gas-liquid chromatography with UV and infrared spectrophotometry and mass spectroscopy of both methyl esters and trimethyl silyl derivatives. By analyzing the fragmentation patterns of these derivatives by three different methods of mass spectroscopy combined with gas-liquid chromatographic separation, the different structural subclasses of mycolic acids were quantitated. Significant qualitative and quantitative modifications of specific mycolic acid subclasses occurred in the cell walls of N. asteroides GUH-2 that were growth stage dependent. The mycolic acids that were predominant in the log phase were polyunsaturated (greater than 2 double bonds per molecule), with long chain lengths and even carbon atom numbers (i.e., C54, C56). In contrast, those that were prominent in the stationary phase were more saturated (few or no double bonds) and of shorter overall carbon chain length (less than or equal to C52). Furthermore, stationary-phase cells had significantly increased amounts of mycolic acids with odd-numbered carbon chain lengths (i.e., C49, C51, C53).     

The catalytic mechanism of serine proteases: single proton versus double proton transfer

The two possible mechanisms of proton transfer on the catalytic process of serine proteases (single or double proton transfer) have been analysed. Intermediate neglect of differential overlap calculations have been performed in the absence and in the presence of the substrate molecule and one water molecule localized in the active site. It is shown that, in the absence of the substrate and water, double proton transfer seems to be the most feasible mechanism. However, when these molecules are introduced in the calculation, the role played by them is to facilitate the formation of the zwitterionic structure (single proton transfer) and to destabilize the intermediate structure which leads to double proton transfer. All calculations were made in vacuo.     

Synthesis and characterization of vegetable oil derived esters: evaluation for their diesel additive properties

Trans-esterification of four vegetable oils; canola oil, greenseed canola oil from heat-damaged seeds, processed waste fryer grease and unprocessed waste fryer grease, was carried out using methanol, and KOH as catalyst. The methyl esters of the corresponding oils were separated from the crude glycerol, purified, and characterized by various methods to evaluate their densities, viscosities, iodine values, acid numbers, cloud points, pour points and gross heat of combustion, fatty acid and lipid compositions, lubricity properties, and thermal properties. The fatty acid composition suggests that 80-85% of the ester was from unsaturated acids. Substantial decrease in density and viscosity of the methyl esters compared to their corresponding oils suggested that the oils were in their mono or di glyceride form. The lubricity of the methyl esters, when blended at 1 vol% treat rate with ISOPAR M reference fuel, showed that the canola methyl ester enhanced the fuel's lubricity number. From the analyses performed, it was determined that the ester with the most potential for being an additive or a substitute for diesel fuel is the canola methyl ester, whose physical and chemical characteristics are similar to diesel fuel.     

Epoxidation of fatty acids,fatty methyl esters,and alkenes by immobilized oat seed peroxygenase

Fatty epoxides are used as plasticizers and plastic stabilizers and are intermediates for the production of other chemical substances. The currently used industrial procedure for fatty epoxide synthesis requires a strong acid catalyst which can cause oxirane ring opening and side product formation. To find a replacement for the acid catalyst, we have been conducting research on a peroxygenase enzyme from oat (Avena sativa) seeds and have devised a method for immobilization of this enzyme using a hydrophobic membrane support. In this study, fatty acids and fatty methyl esters commonly encountered in commercial vegetable oils were tested as substrates for immobilized peroxygenase, and the epoxide products were characterized. The epoxidation time course of linoleic acid showed two distinct phases with nearly complete conversion to monoepoxide before diepoxide was produced. The diepoxide formed from linolenic acid was found to be 9,10-15,16-diepoxy-12-octadecenoic acid, and only a trace of triepoxide was obtained. Additionally it was discovered that acyclic alkenes with internal double bonds, a cyclic alkene, and an alkene with an aromatic substituent were substrates of peroxygenase. However, alkenes with terminal unsaturation were unreactive. With every substrate examined, oat seed peroxygenase exhibited specificity for epoxidation, producing no other products, and oxirane ring opening did not occur.