Epoxy-Slide Embedment of Cytochemically Stained Tissues and Cultured Cells for Light and Electron Microscopy

A new method is described for embedding stained tissue sections, cells, cultured cells or organ cultures in a special polyethylene mold to form epoxy microscope slides (cost-a-slides). Cast-a-slides in which biological specimens are embedded may be examined by light microscopy and individual optimally stained cells or tissue areas selected for examination by various modes of electron microscopy or X-ray microanalysis. Cultured cells or organs can be grown, fixed, stained and embedded in epoxy in the same cast-a-slide mold. The cast-a-slides can be stored conveniently in the same manner as glass microscopy slides.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy.

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5-0.8 microm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8-10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5-0.8 µm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8-10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

A polychromatic staining method for epoxy embedded tissue: a new combination of methylene blue and basic fuchsine for light microscopy

A simple and rapid method is described for staining semithin sections of material embedded in epoxy resin for observing tissues prior to transmission electron microscopy. The method is suitable for tissue fixed with a glutaraldehyde-formaldehyde mixture and postfixed in osmium tetroxide. No etching or oxidizing procedures are necessary. Sections 0.5–0.8 µm thick are dried onto a slide and stained with either 0.75% methylene blue and 0.25% azure B or 0.5% methylene blue and 0.5% azure II in 0.5% aqueous borax and heated over a flame for 8–10 sec. The slides are rinsed with water, then stained the same way with 0.1% basic fuchsine in 5% aqueous ethanol. Cytoplasm stains blue; nuclei darker blue; collagen, mucus and elastin pink to red; fat and intracellular lipid droplets gray-green.     

Plastic-embedded semi-thin sections of fine needle aspiration biopsies with dibasic staining. Diagnostic and didactic applications

The diagnostic and didactic utility of plastic-embedded semi-thin sections of fine needle aspiration biopsies is presented using a case-study approach. The Spurr epoxy semi-thin sections were stained with a newly developed sequential basic fuchsin-methylene blue stain, which gives hematoxylin-and-eosin-like staining and simultaneously substitutes for a wide variety of special stains. The informational content of the sections can approach that of electron microscopy. The use of a direct off-the-slide "pop-off" technique in preparing the plastic-embedded sections allows for a direct comparison between similar groups of cells embedded in plastic and present on the routine aspiration slides; retrospective analysis can discern subtle, previously unrecognized morphologic features in the alcohol-fixed, Papanicolaou-stained slides. The limitations of this comparative approach, however, become manifest when the effects of alcohol fixation on cells are directly compared in plastic and at the ultrastructural level to aldehyde fixation.     

Improved Staining Procedures for Semithin Epoxy Sections of Plant Tissues

Improved and reliable methods are described for staining semithin sections of plant materials fixed in glutaraldehyde-osmium and embedded in epoxy resins. One-micron sections are fixed to slides, stained with a two-solution hematoxylin procedure or with a methylene blue-azure A combination, counterstained in aqueous safranin O, cleared, and mounted permanently. Basophilic tissue components arc stained gray to black by the hematoxylin and blue or purple by the methylene blue-azure A combination; all wall structures are colored by the safranin. With the procedures recommended, stains am sharp and intense, sections arc flat, wrinkling and loss are held to a minimum, and unsightly precipitates do not form.     

Improved staining procedures for semithin epoxy sections of plant tissues.

Improved and reliable methods are described for staining semithin sections of plant materials fixed in glutaraldehyde-osmium and embedded in epoxy resins. One-micron sections are fixed to slides, stained with a two-solution hematoxylin procedure or with a methylene blue-azure A combination, counterstained in aqueous safranin O, cleared, and mounted permanently. Basophilic tissue components are stained gray to black by the hematoxylin and blue or purple by the methylene blue-azure A combination; cell wall structures are colored by the safranin. With the procedures recommended, stains are sharp and intense, sections are flat, wrinkling and loss are held to a minimum, and unsightly precipitates do not form.     

A method for immunohistochemical detection of osteogenic markers in undecalcified bone sections

To evaluate the osteogenic potential of novel implant materials, it is important to examine their effect on osteoblastic differentiation. Characterizing the tissue response at the bone-biomaterial interface in vivo at a molecular level would contribute significantly to enhancing our understanding of tissue integration of endosseous implant materials. We describe here a new technique that overcomes difficulties commonly associated with performing immunohistochemistry on undecalcified sawed sections of bone. Sheep mandible specimens were fixed in an ethanol based fixative to maintain adequate antigenicity of the tissue. As a result, it was possible to omit antigen retrieval at high temperature for recovery of antigenicity, and detachment of sections from the slides was avoided. Following dehydration and infiltration, the specimens were embedded in a resin composed of polymethylmethacrylate and polybutylmethacrylate. Polymerization was achieved by adding benzoylperoxide and N,N-dimethyl-toluidine. This resin was selected because it maintained the antigenicity of the tissue, provided adequate properties for cutting 50 µm thick sections, and it facilitated deacrylizing the sawed sections. Acid-resistant acrylic slides were glued to the blocks using an epoxy resin based two-component adhesive to avoid detachment of the slides during the deacrylation procedure. Samples were stained for alkaline phosphatase, type I collagen, osteonectin, osteopontin, osteocalcin and bone sialoprotein. The EnVision + ™ dextran polymer conjugate two-step visualization system was applied for immunohistochemical detection of these bone matrix proteins. This procedure yielded positive staining for the osteogenic markers in cells and matrix components. The protocol described here facilitates the use of immunohistochemistry on resin embedded sawed sections of bone and provides a convenient and reliable method that can be used routinely for immunohistochemical analysis of hard tissue specimens containing implant materials.     

Histopathologic Technique for the Morphological Examination of Fixed or Frozen Solid Tumor Cells in Soft Agar

Two simple techniques are described for preparing sections from soft agar colony cultures of tumor cells. Tumor cells grown in soft agar can be frozen, sectioned, and stained and/or fixed in formalin, embedded in paraffin, sectioned, mounted on glass slides, and stained. The methods are simple and reproducible. These cells can be stained with various stains and the staining quality is excellent. The paraffin blocks and microscope slides can be stored for permanent record. The use of these techniques should provide better understanding of the histomorphologic characteristics of neoplastic cells which grow in soft agar and should expand and refine prognosis and diagnosis of malignant tumors.     

Virus and prokaryote enumeration from planktonic aquatic environments by epifluorescence microscopy with SYBR Green I

Viruses are the most abundant biological entities in aquatic environments, typically exceeding the abundance of bacteria by an order of magnitude. The reliable enumeration of virus-like particles in marine microbiological investigations is a key measurement parameter. Although the size of typical marine viruses (20-200 nm) is too small to permit the resolution of details by light microscopy, such viruses can be visualized by epifluorescence microscopy if stained brightly. This can be achieved using the sensitive DNA dye SYBR Green I (Molecular Probes-Invitrogen). The method relies on simple vacuum filtration to capture viruses on a 0.02-microm aluminum oxide filter, and subsequent staining and mounting to prepare slides. Virus-like particles are brightly stained and easily observed for enumeration, and prokaryotic cells can easily be counted on the same slides. The protocol provides an inexpensive, rapid (30 min) and reliable technique for obtaining counts of viruses and prokaryotes simultaneously.     

Differential staining of tannin in sections of epoxy-embedded plant cells.

A staining procedure is described for the light microscopic localization of ergastic tannins in epoxy sections of plant cells embedded for study by transmission electron microscopy. Callus and cell suspensions of Pseudotsuga menziesii and Pinus taeda fixed in glutaraldehyde:acrolein and then OsO4, followed by epoxy embedding, were sectioned 0.5 mum thick, stained on a glass slide with ethanolic Sudan black B at 60 C as described by Bronner, and then mounted in Karo syrup. Tannin deposits stained brownish-orange and were easily distinguished from lipid bodies of similar size, which stained dark blue to black, and from starch grains, which were unstained. The significance of this differential polychromasia was confirmed by transmission electron microscopy. This staining procedure should prove valuable in the cytoplasmic evaluation of the plant cell ergastics (especially tannins) via light microscopy whether or not electroc microscopic examination is intended.     

Selective staining of fungal hyphae in parasitic and symbiotic plant-fungus associations

A cytochemical method for light microscopical studies is described which allows the specific detection of fungal hyphae in plant-fungus associations: e.g. lichens, mycorrhiza, or fungal infections of plant tissue. The specimens were fixed and embedded in epoxy resin by a standard protocol for electron microscopy. Semithin sections were successively incubated with fluorescein isothiocyanate labelled wheat germ agglutinin (FITC-WGA) and calcofluor white (CW). FITC-WGA stained exclusively the fungal cell walls while CW stained both the fungal and the plant cell walls. Therefore, FITC-WGA is an excellent marker for the fungal hyphae.     

Preparing Epoxy Sections of Insect Tissues for Light Microscopy

Sections of aldehyde-fixed and osmium-stained insect tissues embedded in various epoxy resins were affixed to glass slides by use of a slide cover and hotplate combination. A high concentration of solvent vapor over the sections was thus maintained while they dried down on the slides, resulting in excellent flatness and adhesion. Sections were then stained at an elevated temperature with a mixture of equal parts of 3 dye solutions: 1% toluidine blue O, 1% safranin O, and saturated auramine O, all made up in 1% solution of borax in water. The method resulted in excellent differentiation of all insect tissue components including lightly chitinized structures.     

Differential Staining of Tannin in Sections of Epoxy-Embedded Plant Cells

A staining procedure is described for the light microscopic localization of ergastic tannins in epoxy sections of plant cells embedded for study by transmission electron microscopy. Callus and cell suspensions of Pseudotsuga menziesii and Pinus taeda fixed in glutaraldehyde:acrolein and then OsO₄, followed by epoxy embedding, were sectioned 0.5 μn thick, stained on a glass slide with ethanolic Sudan black B at 60 C as described by Bronner, and then mounted in Karo syrup. Tannin deposits stained brownish-orange and were easily distinguished from lipid bodies of similar size, which stained dark blue to black, and from starch grains, which were unstained. The significance of this differential polychromasia was confirmed by transmission electron microscopy. This staining proadure should prove valuable in the cytoplasmic evaluation of the plant cell ergastics (especially tannins) via light microscopy whether or not electron microscopic examination is intended.     

Polychromatic staining of epoxy semithin sections: a new and simple method

A simple, rapid method is described for the polychromatic coloration of semithin sections, which is applicable to material routinely processed for transmission electron microscopy. Material fixed with a glutaraldehyde-paraformaldehyde mixture and postfixed in osmium tetroxide with or without potassium ferrocyanide and embedded in different types of resin (Durkupan-ACM, Spurr resin, Taab resin) can be used. Constant and homogenous results are obtained with this technique, the staining procedure being achieved at room temperature in no more than 10 min. Sections of 0.5–1 m in thickness are oxidised and bleached. After washing, sections are stained in two steps with carbol methylene blue/carbol gentian violet solution and pararosaniline solution. Using the method described in this paper, a polychromatic coloration of the different cells and tissues was obtained (epithelial cells in various shades of blue-violet, connective tissue and elastic laminae of blood vessels in pink or red, etc.). This procedure provides greater contrast between cytoplasm and nuclei, and among the different types of cells and tissues than is seen with toluidine blue, which is very useful for observation and photography of semithin sections. Polychromatic methods found in the literature are normally complex and require a lengthy staining time or cannot be applied on material routinely processed for transmission electron microscopy. Our method is simple, rapid and can be used on any type of material routinely processed for transmission electron microscopy and embedded in epoxy resins.     

DNA cytofluorometry in micro-dissected paraffin embedded breast tissue: description of a method

DNA microfluorometry on smears obtained from paraffin embedded tissue has been shown to be a distinctive possibility. In this paper a simple method for the detachment of cells from mammary ducts and ductules is described. Areas of interest were selected in conventional slides stained with Haematoxylin and Eosin. The corresponding paraffin embedded block was then dewaxed. The areas under study were retraced with a stereomicroscope and the cells within ducts and ductules were scraped out with a 0.4 mm diameter fine needle. Cells were isolated with mechanical and enzymatic procedures and stained with the Feulgen reaction. The DNA content of single cells was then measured using a microfluorometer.     

A novel tight cylindrical mold for epoxy resin embedding allows enhanced microscopic analysis of microcores extracted from woody plants

A novel mold was devised to embed microcores extracted from stems of trees in epoxy resin, which has been widely used for optical and electron microscopic analysis of xylem formation. The embedding mold of a tight cylindrical shaped tube was designed to avoid displacement of microcores from the right position during the process of resin embedding. Microcores of a ring-porous hardwood species, Quercus crispula, with higher wood density and much larger differentiating vessel elements laid down on the boundary between the current xylem and the previous one, which generally cause difficulty in thin sectioning and breaks in sections, respectively, were embedded in the cylindrical molds full of epoxy resin. Locations of the three principal planes of wood anatomy could be determined in cylindrical resin-embedded microcores as follows: the transverse plane could be found on their side of cylinder, the radial one was vertical to the transverse, and the tangential ones were their circular ends of cylinder. The present embedding mold, therefore, can provide all three principal sections for microscopic wood anatomy from the side or ends of the same cylindrical microcore in principle. To confirm the usefulness of the resin-embedded microcores, we examined the differentiation of vessel elements during the period of earlywood formation on their transverse sections under microscopes, consequently could observe cell division in the cambial zone and sequential stages of vessel element differentiation, including cell expansion and deposition of the secondary cell wall. The present embedding mold for epoxy resin is simple but highly useful and innovative for a wide range of applications of microcores in microscopy for studies on tree-ring formation.     

Wafer embedding: Specimen selection in electron microscopic cytochemistry with osmiophilic polymers

Synopsis A new wafer embedding procedure is described that permits light microscopic screening of embedded tissue prior to ultrathin sectioning. It is particularly valuable when used on specimens obtained with an automatic sectioner and treated cytochemically to obtain visible intermediate or visible and electron opaque final reaction products. Aldehyde-fixed tissues are cut into sections with an automatic sectioner, incubated cytochemically including osmication if required, then embedded in epoxy resin between fluorocarbon-coated coverglasses which are supported by a platform specially designed for this purpose. The resultant wafer, less than 0.2 mm thick, is examined by light microscopy for optimal areas of cytochemical reaction and desirable structural features. Such areas are cut out and glued to blank blocks with fast curing cyanoacrylate cement for subsequent ultrathin sectioning. The usefulness of this technique is demonstrated by the location of: (1) esterase-positive lysosomes in kidney and trigeminal ganglia; (2) palatal sensory endings stained for acetylcholinesterase; and (3) phagosomes arising from the resorption of horseradish peroxidase tracer by the cuboidal parietal epithelial cells of Bowman's capsule in the male mouse.     

Photographic Mapping of a Tissue Surface to Locate Fields for Electron Microscopy; Mouse Lung

Precise sampling from whole lobes of mouse lungs fixed in the inflated state and embedded in epoxy resin can be not only feasible but also efficient. A 1 μm section is cut from an embedded lobe with a rotary microtome and a steel knife. This section is stained and photographed, and from it a 35 × enlarged print is prepared. A grid of transparent plastic scored with 35 mm squares, lettered vertically and numbered horizontally, is superimposed over the photograph. The area chosen for electron microscopy thus becomes identifiable by a letter-number designation obtained from the grid. This area is then located by light microscopy on a 2 mm slice taken from the block from which the 1 μm section was cut, by use of oblique illumination and the calibrated mechanical stage of the light microscope. A block of 1.3 mm diameter is removed for electron microscopy from the tissue by a rotatable circular spring-loaded punch screwed into the objective turret of the microscope. The removed cylinder is mounted on a metal stub and ultrathin sections cut from the faced tissue. The method is as equally suitable for the examination of other tissues, particularly when large areas and multiple sampling may be required.     

Localization of cathepsin L in rat kidney revealed by immunoenzyme and immunogold techniques

Localization of cathepsin L in rat kidney was investigated by immunocytochemical techniques. Kidneys were fixed by perfusion and embedded in Epon or Lowicryl K4M without postosmication. For light microscopy (LM), semi-thin sections of the Epon-embedded material were stained by the immunoenzyme technique after removal of epoxy resin. For electron microscopy (EM), ultra-thin sections of Lowicryl K4M-embedded material were stained by the protein A-gold technique. By LM, reaction deposits for cathepsin L were present in the cytoplasmic granules of proximal tubule cells, but little or no reaction product was noted in distal tubule, collecting tubule, and most of urinary tubules in the medulla. By EM, heavy gold label for cathepsin L was confined exclusively to lysosomes of the proximal tubule cells, but little or no label to those of the other segments. In immunocytochemical control sections, no reaction was observed. These results indicate that a main container of cathepsin L is lysosomes of the proximal tubule and suggest that the enzyme plays a role in the degradation of endocytosed proteins.