A new less toxic polymer gel dosimeter: Radiological characteristics and dosimetry properties

PurposeA new polymer gel dosimeter recipe was investigated that may be more suitable for widespread applications than polyacrylamide gel dosimeters, since the extremely toxic acrylamide has been replaced with the less harmful monomer 2-Acrylamido 2-Methyl Propane Sulfonic acid (AMPS).MethodsThe new formulation was named PAMPSGAT. The MRI response (R2) of the dosimeters was analyzed for conditions of varying dose, dose rate, and temperature during scanning. Radiological properties of the PAMPSGAT polymer gel dosimeter were investigated.ResultsThe dose-response (R2) of AMPS/Bis appears to be linear over a dose range 10–40 Gy. The percentage of difference between the R2 values for imaging at 15 °C and MRI room temperature is about 4.6% for vial with 40 Gy absorbed dose which decreased to less than 1% for imaging at 20 °C. The percentage difference of Zeff of PAMPSGAT gel and soft tissue was less than 1% in the practical energy range (100 KeV–100 MeV). The electron density of the PAMPSGAT polymer gel was 2.9% higher than that of muscle. Results showed that the sensitivity of PAMPSGAT polymer gel dosimeter irradiated by ⁶⁰Co (energy = 1.25 MeV) is about 27.7% higher than that of irradiated using a 6 MeV Linac system.ConclusionsTemperature during MRI scanning has a small effect on the R2 response of the PAMPSGAT polymer gel dosimeter. Results confirmed tissue equivalency of the PAMPSGAT polymer gel dosimeter in most practical energy range. The PAMPSGAT polymer gel dosimeter response depends on energy and dose rate.     

The SMXA: a new set of recombinant inbred strain of mice consisting of 26 substrains and their genetic profile

A new set of recombinant inbred (RI) strain SMXA consisting of 26 substrains was established between SM/J and A/J. The history of the SMXA RI strains and their genetic prolife covering 158 genetic marker loci are reported. From the strain distribution pattern among SMXA RI strains, the chromosomal location of salivary and tear protein genes Spel-r, Spel-s, Spe2, and Tpe1 were newly determined.     

Photothermal beam deflection: a new method for in vivo measurements of thermal energy dissipation and photochemical energy conversion in intact leaves

A novel photosynthetic technique, photothermal deflection spectroscopy, is presented which is based on the mirage effect and allows the rapid measurement of thermal deactivation of excited pigments in leaf samples placed in an open cell. Modulated heat emission from leaves illuminated with intensity-modulated light was measured via the detection of the periodic deflection of a laser beam parallel to the sample surface. Photothermal deflection signals can be monitored in vivo in leaves placed in various, liquid or gaseous, environments with a satisfactory signal-to-noise ratio close to 60–80 (in distilled water) at low modulation frequencies (below 50 Hz). Using this new and simple photothermal method, it was possible to easily obtain useful information on the leaf photochemical activity and its light-saturation characteristics under normal or stress conditions, suggesting that in vivo deflection signals could be used for assaying the photosynthetic state of health of crop plants. The beam deflection method presented in this paper appears to be a potentially useful photosynthetic tool complementary to the related photoacoustic technique.Abbreviations DCMU dichlorophenyldimethylurea - PD photothermal deflection - PL photochemical energy storage - S/N ratio signal-to-noise ratio     

Effect of varying dose-per-pulse and average dose rate in X-ray beam irradiation on cultured cell survival

Characterizing the biological effects of flattening filter-free (FFF) X-ray beams from linear accelerators is of importance, due to their increasing clinical availability. The purpose of this work is to determine whether in vitro cell survival is affected by the higher dose-per-pulse present in FFF beams in comparison with flattened X-ray beams. A Varian TrueBeam^® linear accelerator was used to irradiate the T98G, V79-4 and U87-MG cell lines with a single fraction of 5 Gy or 10 Gy doses of X-rays. Beams with energies of 6 MegaVolt (MV), 6 MV FFF and 10 MV FFF were used, with doses-per-pulse as measured at the monitor chamber of 0.28, 0.78 and 1.31 mGy/pulse for 6 MV, 6 MV FFF and 10 MV FFF, respectively. The dose delivered to each Petri dish was verified by means of ionization chamber measurements. No statistically significant effects on survival fraction were observed for any of the cell lines considered, either as a function of dose-per-pulse, average dose rate or total dose delivered. Biological effects of higher instantaneous rates should not be excluded on the basis of in vitro experimental results such as the ones presented in this work. The next step toward an assessment of the biological impact of FFF beams will require in vivo studies.     

X-ray study on egg-yolk lecithin: Unit cell data and electron density profile

The unit cell dimensions and space group of egg-yolk lecithin (l-α-phosphatidylcholine) in the crystalline state were obtained from a set of X-ray fibre diagrams recorded from specimens oriented in two different axes; $\text{a = 8.84}\text{A}\text{?}\text{± 0.05}\text{A}\text{?}\text{, b = 10.07}\text{A}\text{?}\text{± 0.05}\text{A}\text{?}\text{, c = 54.69}\text{A}\text{?}\text{± 0.05}\text{A}\text{?}$, with space group P2₁2₁2, and four molecules per unit cell. From the 00l reflexions up to the 25th order, an electron density profile is obtained which is consistent with a probable structure of the molecule.     

Light scattering measurements on gangliosides: dependence of micellar properties on molecular structure and temperature

Static and dynamic laser light scattering measurements on micellar aqueous solutions of gangliosides GM2, GM1, GD1a are reported. The aggregation number, the hydrodynamic radius and the micellar shape depend on the type of ganglioside and the unsaturation degree of the hydrocarbon chains. At a temperature of 25 degrees C the molecular weights of GM2, GM1 and GD1a are 740,000, 470,000 and 418,000 DA respectively. A significant decrease of micellar size with temperature has been found for saturated GM1 in the region 25 degrees-40 degrees C. The strong sensitivity of the micellar parameters to the ganglioside structure is explained by making reference to some simple model which takes into account geometrical packing considerations. By measuring the scattered light intensity at low ionic strength of the solution (0.1-30 mE) it was possible to evaluate the ganglioside micellar charge, 100 electronic units for GM2, 48 for GM1 and 60 for GD1a.     

Effect of erythropifadin on the morphofunctional characteristics of donor blood preserved for a long time

Adenine- and riboxine-containing erythropifaden has been studied for possibility to be used for restoring a functional value of erythrocytes in conserved donor blood stored for 35-49 days. Energy supply and oxygen transport function of erythrocytes are shown to get normal and their morphological composition--to get considerably improved. Besides, osmotic resistance and deformability of erythrocytes insignificantly change while concentration of riboxine in blood and that of substances with average molecular mass remain considerably high. One of the ways to remove the above shortcomings is application of hemosorbents.     

Effects of ethidium bromide on DNA loop organisation in human lymphocytes measured by anomalous viscosity time dependence and single cell gel electrophoresis.

The effects of ethidium bromide (EtBr) on human lymphocytes were studied by the method of anomalous viscosity time dependence (AVTD) and by the comet assay. EtBr at low concentrations increased the maximum viscosity and time of radial migration as measured with AVTD at neutral conditions of lysis. A pronounced relaxation of DNA loops was observed with the neutral comet assay. The maximal comet length corresponded to 2 Mb DNA loops. At high concentrations of EtBr, 2 mg/ml, significant reduction in AVTD below control level was seen that suggested hypercondensation of chromatin. The hypercondensation was directly observed with the neutral comet assay. EtBr did not induce DNA strand breaks as measured by the alkaline comet assay. The hypercondensed nuclei could be decondensed by irradiation with gamma-rays or exposure to light. The data provide evidence that EtBr at high concentrations resulted in hypercondensation of chromatin below control level. The comet assay confirmed that the increase in AVTD peaks deals with relaxation of loops and AVTD decrease is caused by chromatin condensation. The prediction of the AVTD theory for a correlation between time of radial migration and condensation of chromatin was verified. Further, the data show that the comet assay at neutral conditions of lysis is rather sensitive to DNA loop relaxation in the absence of DNA damage. Finally, donor specificity was found for the hypercondensation.     

cAMP-dependent protein kinases, their subunits, and cAMP-binding protein from four sources: a comparison of physical characteristics determined by polyacrylamide gel electrophoresis

The physical characteristics of cAMP-dependent protein kinases and their, regulatory subunits from calf uterus, human uterus, human mammary tumor, and rat pituitary and of cAMP-binding protein from calf uterus were determined by quantitative polyacrylamide gel electrophoresis in buffers containing the detergent, Triton X-100. In the four tissues, protein kinases of either type A¹, with molecular weight (M_r) = 200,000, or type B, of M_r = 80,000, or both, previously described were found. Trivial charge isomerism, or size isomerism, exists within each of the two classes, Protein Kinase A and B. The protein kinase recombined from the regulatory and catalytic subunits is not significantly different from the crude or isolated protein kinase. Protein Kinases A and B exist each in either one of the isozyme forms I and II but these are not reflected in polyacrylamide gel electrophoresis at pH 10.2. Protein Kinase B appears to be a product of the partial proteolysis of Protein Kinase A. The regulatory subunits of Protein Kinases A from the four tissues are distinct from those of Protein Kinases B. No physical distinction exists between regulatory subunits derived from isozyme forms I and II. cAMP-Binding Proteins A and B are physically indistinguishable, by polyacrylamide gel electrophoresis at pH 10.2, from the regulatory subunits of Protein Kinases A and B, respectively.     

Carbonic anhydrase: a new method of detection on polyacrylamide gels using conductivity measurements

Carbonic anhydrase could be located on polyacrylamide gels by conductivity measurements using CO₂ as a substrate. The rapid increase of ions at the site of enzymatic localization caused an enhancement of conductivity which could be immediately recorded by the described technique.     

Biofilm formation by strains of Burkholderia cepacia complex in dependence of their phenotypic and genotypic characteristics

Biofilm formation was studied in 54 strains of Burkholderia cepacia complex isolated in 7 Moscow hospitals. 80% of strains (biofilm groups I and II) had the capacity to biofilm formation and only 16.7% of strains (group III) were not capable to biofilm formation. Molecular genetic methods allowed to identify one of the epidemic markers (CBL, IS hybrid sequence, Burkholderia Cepacia Epidemic Strain Marker - BCESM) in 46.7, 23.3, and 33.3% of strains from group I, II, and III respectively. Gene cepR from the Quorum Sensing system was identified in three biofilm groups in nearly equal frequency (92.3, 96.2 and 100% for group I, II, and III respectively), whereas cepl gene was found more often in group I (76.9%) and II (65.4%). Strains from all three groups had protease and lipase activity and 13.3% of group I strains had chitinolytic activity. B. cepacia strains from group I produced hemolysin in 33.3% of cases, from group II--in 26.6%, and from group III--in 11.1% of cases. The majority of Moscow hospital strains of B. cepacia complex were identified as B. cenocepacia (genomovar III, group A). RAPD-PCR method enabled to differentiate isolated strains into several genotypic variants. 13.3% of strains from group I were susceptible to imipenem/ciprofloxacin, as well as 33.3% of isolates from group II and 44.4% of isolates from group III.     

The influence of time,soil characteristics,and land‐use history on soil phosphorus legacies: a global meta‐analysis

Agriculturally driven changes in soil phosphorus (P) are known to have persistent effects on local ecosystem structure and function, but regional patterns of soil P recovery following cessation of agriculture are less well understood. We synthesized data from 94 published studies to assess evidence of these land‐use legacies throughout the world by comparing soil labile and total P content in abandoned agricultural areas to that of reference ecosystems or sites remaining in agriculture. Our meta‐analysis shows that soil P content was typically elevated after abandonment compared to reference levels, but reduced compared to soils that remained under agriculture. There were more pronounced differences in the legacies of past agriculture on soil P across regions than between the types of land use practiced prior to abandonment (cropland, pasture, or forage grassland). However, consistent patterns of soil P enrichment or depletion according to soil order and types of post‐agricultural vegetation suggest that these factors may mediate agricultural legacies on soil P. We also used mixed effects models to examine the role of multiple variables on soil P recovery following agriculture. Time since cessation of agriculture was highly influential on soil P legacies, with clear reductions in the degree of labile and total P enrichment relative to reference ecosystems over time. Soil characteristics (clay content and pH) were strongly related to changes in labile P compared to reference sites, but these were relatively unimportant for total P. The duration of past agricultural use and climate were weakly related to changes in total P only. Our finding of reductions in the degree of soil P alteration over time relative to reference conditions reveals the potential to mitigate these land‐use legacies in some soils. Better ability to predict dynamics of soil nutrient recovery after termination of agricultural use is essential to ecosystem management following land‐use change.     

Effect of heating temperature and time on pharmaceutical characteristics of albumin microspheres containing 5-fluorouracil

Conclusion  In this study, we found that both heating temperature and heating time affect mean particle size, particle size distribution, and drug entrapment efficiency of albumin microspheres. The change in heating temperature may affect the particle size of the product, especially when heating is carried out at a lower temperature (90°C–120°C). Hence the temperature should be selected on the basis of desired size range. Given that it is desirable for a maximum amount of the drug used in the preparation to become entrapped in microspheres, heating temperature and heating time for denaturation of albumin should be selected cautiously, as both have a significant effect on drug entrapment efficiency. In the present case, the highest entrapment was found in batches prepared by heating at 90°C for 5 minutes. However, the extent of stabilization at the selected temperature and the time of heating should also be taken into consideration, as they may affect the release of drugs to target tissue.     

Evaluation of a new laser surface implant: scanning electron microscopy/energy dispersive X-ray and X-ray photoelectron spectroscopy analyses

The roughness and the purity of implant surfaces are key points in the osteointegration process. The surfaces obtained by classic methods present irregular non-reproducible patterns and furthermore contaminate the implant surface with materials other than titanium which interfere with the process of osteointegration. The aim of the present study is to evaluate, by SEM/EDX and XPS analyses, the surface microstructure and the purity of new laser-treated implant surfaces. The laser treatment of the surface allows to set parameters to determine the roughness in order to obtain a regular and repeatable surface. Furthermore, there being no contact between the implant and the machine, there is no surface contamination with elements other than titanium. In this study we used a diode-pumped solid state laser (DPSS) with Nd:YAG source operating in Q-Switching mode on titanium samples. The resulting samples were analysed by SEM/EDX and XPS to evaluate morphology and purity of the surface. The results show surfaces with very regular roughness and a total absence of contamination.