Understanding the Reduced Efficiencies of Organic Solar Cells Employing Fullerene Multiadducts as Acceptors

The use of fullerenes with two or more adducts as acceptors has been recently shown to enhance the performance of bulk‐heterojunction solar cells using poly(3‐hexylthiophene) (P3HT) as the donor. The enhancement is caused by a substantial increase in the open‐circuit voltage due to a rise in the fullerene lowest unoccupied molecular orbital (LUMO) level when going from monoadducts to multiadducts. While the increase in the open‐circuit voltage is obtained with many different polymers, most polymers other than P3HT show a substantially reduced photocurrent when blended with fullerene multiadducts like bis‐PCBM (bis adduct of Phenyl‐C₆₁‐butyric acid methyl ester) or the indene C₆₀ bis‐adduct ICBA. Here we investigate the reasons for this decrease in photocurrent. We find that it can be attributed partly to a loss in charge generation efficiency that may be related to the LUMO‐LUMO and HOMO‐HOMO (highest occupied molecular orbital) offsets at the donor‐acceptor heterojunction, and partly to reduced charge carrier collection efficiencies. We show that the P3HT exhibits efficient collection due to high hole and electron mobilities with mono‐ and multiadduct fullerenes. In contrast the less crystalline polymer Poly[[9‐(1‐octylnonyl)‐9H‐carbazole‐2,7‐diyl]‐2,5‐thiophenediyl‐2,1,3‐benzothiadiazole‐4,7‐diyl‐2,5‐thiophenediyl (PCDTBT) shows inefficient charge carrier collection, assigned to low hole mobility in the polymer and low electron mobility when blended with multiadduct fullerenes.     

Sequential Processing for Organic Photovoltaics: Design Rules for Morphology Control by Tailored Semi‐Orthogonal Solvent Blends

Design rules are presented for significantly expanding sequential processing (SqP) into previously inaccessible polymer:fullerene systems by tailoring binary solvent blends for fullerene deposition. Starting with a base solvent that has high fullerene solubility, 2‐chlorophenol (2‐CP), ellipsometry‐based swelling experiments are used to investigate different co‐solvents for the fullerene‐casting solution. By tuning the Flory‐Huggins χ parameter of the 2‐CP/co‐solvent blend, it is possible to optimally swell the polymer of interest for fullerene interdiffusion without dissolution of the polymer underlayer. In this way solar cell power conversion efficiencies are obtained for the PTB7 (poly[(4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)(3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl)]) and PC₆₁BM (phenyl‐C₆₁‐butyric acid methyl ester) materials combination that match those of blend‐cast films. Both semicrystalline (e.g., P3HT (poly(3‐hexylthiophene‐2,5‐diyl)) and entirely amorphous (e.g., PSDTTT (poly[(4,8‐di(2‐butyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)‐alt‐(2,5‐bis(4,4′‐bis(2‐octyl)dithieno[3,2‐b:2′3′‐d]silole‐2,6‐diyl)thiazolo[5,4‐d]thiazole)]) conjugated polymers can be processed into highly efficient photovoltaic devices using the solvent‐blend SqP design rules. Grazing‐incidence wide‐angle x‐ray diffraction experiments confirm that proper choice of the fullerene casting co‐solvent yields well‐ordered interdispersed bulk heterojunction (BHJ) morphologies without the need for subsequent thermal annealing or the use of trace solvent additives (e.g., diiodooctane). The results open SqP to polymer/fullerene systems that are currently incompatible with traditional methods of device fabrication, and make BHJ morphology control a more tractable problem.     

Toward High‐Temperature Stability of PTB7‐Based Bulk Heterojunction Solar Cells: Impact of Fullerene Size and Solvent Additive

The use of fullerene as acceptor limits the thermal stability of organic solar cells at high temperatures as their diffusion inside the donor leads to phase separation via Ostwald ripening. Here it is reported that fullerene diffusion is fully suppressed at temperatures up to 140 °C in bulk heterojunctions based on the benzodithiophene‐based polymer (the poly[[4,8‐bis[(2‐ethylhexyl)oxy]‐benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]‐thieno[3,4‐b]thiophenediyl]], (PTB7) in combination with the fullerene derivative [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₀BM). The blend stability is found independently of the presence of diiodooctane (DIO) used to optimize nanostructuration and in contrast to PTB7 blends using the smaller fullerene derivative PC₇₀BM. The unprecedented thermal stability of PTB7:PC₇₀BM layers is addressed to local minima in the mixing enthalpy of the blend forming stable phases that inhibit fullerene diffusion. Importantly, although the nanoscale morphology of DIO processed blends is thermally stable, corresponding devices show strong performance losses under thermal stress. Only by the use of a high temperature annealing step removing residual DIO from the device, remarkably stable high efficiency solar cells with performance losses less than 10% after a continuous annealing at 140 °C over 3 days are obtained. These results pave the way toward high temperature stable polymer solar cells using fullerene acceptors.     

The Effect of PCBM Dimerization on the Performance of Bulk Heterojunction Solar Cells

Increasing the lifetime of polymer based organic solar cells is still a major challenge. Here, the photostability of bulk heterojunction solar cells based on the polymer poly[4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐[2,5‐bis(3‐tetradecylthiophen‐2‐yl)thiazole[5,4‐d]thiazole)‐1,8‐diyl] (PDTSTzTz) and the fullerene [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₀BM) under inert atmosphere is investigated. Correlation of electrical measurements on complete devices and UV‐vis absorption measurements as well as high‐performance liquid chromatography (HPLC) analysis on the active materials reveals that photodimerization of PC₆₀BM is responsible for the observed degradation. Simulation of the electrical device parameters shows that this dimerization results in a significant reduction of the charge carrier mobility. Both the dimerization and the associated device performance loss turn out to be reversible upon annealing. BisPC₆₀BM, the bis‐substituted analog of PC₆₀BM, is shown to be resistant towards light exposure, which in turn enables the manufacture of photostable PDTSTzTz:bisPC₆₀BM solar cells.     

Work Function Control of Interfacial Buffer Layers for Efficient and Air‐Stable Inverted Low‐Bandgap Organic Photovoltaics

A water‐soluble cationic polythiophene derivative, poly[3‐(6‐{4‐tert‐butylpyridiniumyl}‐hexyl)thiophene‐2,5‐diyl] [P3(TBP)HT], is combined with anionic poly(3,4‐ethylenedioxythiophene):poly(p‐styrenesulfonate) (PEDOT:PSS) on indium tin oxide (ITO) substrates via electrostatic layer‐by‐layer (eLbL) assembly. By varying the number of eLbL layers, the electrode's work function is precisely controlled from 4.6 to 3.8 eV. These polymeric coatings are used as cathodic interfacial modifiers for inverted‐mode organic photovoltaics that incorporate a photoactive layer composed of either poly[(3‐hexylthiophene)‐2,5‐diyl] (P3HT) and the fullerene acceptor [6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or the low bandgap polymer [poly({4,8‐di(2‐ethylhexyloxyl)benzo[1,2‐b:4,5‐b′]dithiophene}‐2,6‐diyl)‐alt‐({5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}‐1,3‐diyl) (PBDTTPD)] and the electron acceptor [6,6‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM)]. The power conversion efficiency (PCE) of the resulting photovoltaic device is dependent on the composition of the eLbL‐assembled interface and permits the fabrication of devices with efficiencies of 3.8% and 5.6% for P3HT and PBDTTPD donor polymers, respectively. Notably, these devices demonstrate significant stability with a P3HT:PC₆₁BM system maintaining 83% of its original PCE after 1 year of storage and a PBDTTPD:PC₇₁BM system maintaining 97% of its original PCE after over 1000 h of storage in air, according to the ISOS‐D‐1 shelf protocol.     

Electron Collection as a Limit to Polymer:PCBM Solar Cell Efficiency: Effect of Blend Microstructure on Carrier Mobility and Device Performance in PTB7:PCBM

The poor photovoltaic performance of state‐of‐the‐art blends of poly[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl] (PTB7) and [6,6]‐phenyl‐C61‐butyric acid (PCBM) at large active layer thicknesses is studied using space‐charge‐limited current mobility and photovoltaic device measurements. The poor performance is found to result from relatively low electron mobility. This is attributed to the low tendency of PTB7 to aggregate, which reduces the ability of the fullerene to form a connected network. Increasing the PCBM content 60–80 wt% increases electron mobility and accordingly improves performance for thicker devices, resulting in a fill factor (FF) close to 0.6 at 300 nm. The result confirms that by improving only the connectivity of the fullerene phase, efficient electron and hole collection is possible for 300 nm‐thick PTB7:PCBM devices. Furthermore, it is shown that solvent additive 1,8‐diiodooctane (DIO), used in the highest efficiency PTB7:PCBM devices, does not improve the thickness dependence and, accordingly, does not lead to an increase in either hole or electron mobility or in the carrier lifetime. A key challenge for researchers is therefore to develop new methods to ensure connectivity in the fullerene phase in blends without relying on either a large excess of fullerene or strong aggregation of the polymer.     

Fullerene Nucleating Agents: A Route Towards Thermally Stable Photovoltaic Blends

The bulk‐heterojunction nanostructure of non‐crystalline polymer:fullerene blends has the tendency to rapidly coarsen when heated above its glass transition temperature, which represents an important degradation mechanism. We demonstrate that fullerene nucleating agents can be used to thermally arrest the nanostructure of photovoltaic blends that comprise a non‐crystalline thiophene‐quinoxaline copolymer and the widely used fullerene derivative [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM). To this end, C₆₀ fullerene is employed to efficiently nucleate PCBM crystallization. Sub‐micrometer‐sized fullerene crystals are formed when as little as 2 wt% C₆₀ with respect to PCBM is added to the blend. These reach an average size of only 200 nanometers upon introduction of more than 8 wt% C₆₀. Solar cells based on C₆₀‐nucleated blends indicate significantly improved thermal stability of the bulk‐heterojunction nanostructure even after annealing at an elevated temperature of 130 °C, which lies above the glass transition temperature of the blend. Moreover, we find that various other compounds, including C₇₀ fullerene, single‐walled carbon nanotubes, and sodium benzoate, as well as a number of commercial nucleating agents—commonly used to clarify isotactic polypropylene—permit to control crystallization of the fullerene phase.     

Inverted Semi‐transparent Polymer Solar Cells with Transparency Color Rendering Indices approaching 100

Window‐ or building‐integrated semi‐transparent solar cells are particularly interesting applications for organic photovoltaic devices. In this work, we present an easy‐to‐process inverted device architecture comprising fully solution processable poly(3,4‐ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) bilayer top‐electrodes for efficient semi‐transparent organic solar cells. By incorporating dyes with a complementary absorption to the light harvesting polymer poly[[9‐(1‐octylnonyl)‐9H‐carbazole‐2,7‐diyl]‐2,5‐thiophenediyl‐2,1,3‐benzothiadiazole‐4,7‐diyl‐2,5‐thiophenediyl] (PCDTBT) into the PEDOT:PSS electrode, we achieve fully color neutral transparency perception and a color rendering index approaching 100. This makes the devices suitable for applications such as window shadowing or the integration into overhead glazing.     

Efficient Semi‐Transparent Organic Solar Cells with Good Transparency Color Perception and Rendering Properties

Window integrated photovoltaics for automotive and building applications are a promising market segment for organic solar modules. Besides semi‐transparency, window integrated applications require a reasonable transparency perception and good color rendering properties in order to be suitable for realistic scene illumination. Here, the transmitted light through semi‐transparent organic solar cells comprising the polymer/fullerene blend poly[(4,4'‐bis(2‐ethylhexyl)dithieno[3,2‐b:2',3'‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl]: [6,6]‐phenyl C₇₁‐butric acid methyl ester (PSBTBT:PC₇₀BM) as active layer and a sputtered aluminum doped zinc oxide cathode were found to exhibit a color neutral perception for the human eye and very good color rendering properties. Moreover, the electrical cell properties allow for efficient energy harvesting with an overall power conversion efficiency η ≈ 3%.     

Domain Compositions and Fullerene Aggregation Govern Charge Photogeneration in Polymer/Fullerene Solar Cells

The complex microstructure of organic semiconductor mixtures continues to obscure the connection between the active layer morphology and photovoltaic device performance. For example, the ubiquitous presence of mixed phases in the active layer of polymer/fullerene solar cells creates multiple morphologically distinct interfaces which are capable of exciton dissociation or charge recombination. Here, it is shown that domain compositions and fullerene aggregation can strongly modulate charge photogeneration at ultrafast timescales through studies of a model system, mixtures of a low band‐gap polymer, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]germole)‐2,6‐diyl‐alt‐(2,1,3‐benzothia‐diazole)‐4,7‐diyl], and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester. Structural characterization using energy‐filtered transmission electron microscopy (EFTEM) and resonant soft X‐ray scattering shows similar microstructures even with changes in the overall film composition. Composition maps generated from EFTEM, however, demonstrate that compositions of mixed domains vary significantly with overall film composition. Furthermore, the amount of polymer in the mixed domains is inversely correlated with device performance. Photoinduced absorption studies using ultrafast infrared spectroscopy demonstrate that polaron concentrations are highest when mixed domains contain the least polymer. Grazing‐incidence X‐ray scattering results show that larger fullerene coherence lengths are correlated to higher polaron yields. Thus, the purity of the mixed domains is critical for efficient charge photogeneration because purity modulates fullerene aggregation and electron delocalization.     

The Role of Exciton Ionization Processes in Bulk Heterojunction Organic Photovoltaic Cells

To realize efficient photoconversion in organic semiconductors, photogenerated excitons must be dissociated into their constituent electronic charges. In an organic photovoltaic (OPV) cell, this is most often accomplished using an electron donor–acceptor (D–A) interface. Interestingly, recent work on MoO_x/C₆₀ Schottky OPVs has demonstrated that excitons in C₆₀ may also undergo efficient bulk‐ionization and generate photocurrent as a result of the large built‐in field created by the MoO_x/C₆₀ interface. Here, it is demonstrated that bulk ionization processes also contribute to the short‐circuit current density (J_SC) and open‐circuit voltage (V_OC) in bulk heterojunction (BHJ) OPVs with fullerene‐rich compositions. Temperature‐dependent measurements of device performance are used to distinguish dissociation by bulk‐ionization from charge transfer at the D–A interface. In optimized fullerene‐rich BHJs based on the D–A pairing of boron subphthalocyanine chloride (SubPc)–C₆₀, bulk‐ionization is found to be responsible for ≈16% of the total photocurrent, and >30% of the photocurrent originating from C₆₀. The presence of bulk‐ionization in C₆₀ also impacts the temperature dependence of V_OC, with fullerene‐rich SubPc:C₆₀ BHJ OPVs showing a larger V_OC than evenly mixed BHJs. The prevalence of bulk‐ionization processes in efficient, fullerene‐rich BHJs underscores the need to include these effects when engineering device design and morphology in OPVs.     

Geometrical deformation and failure behavior of C60 fullerene dimer under applied external electric field

By the quantum-molecular dynamics (QMD) technique based on the Roothaan–Hall equation and the Newton motion law, geometrical deformation and failure behavior of C₆₀ fullerene dimer (2C₆₀) as well as single C₆₀ fullerene under applied external electric field are simulated. Further, the effects of the electric field direction on the electric field-induced deformation, polarization-charge distribution and dipole moment of the fullerene molecules are discussed systemically. It is found that the geometrical configuration and failure behavior of the 2C₆₀ molecule are sensitive to the electric field direction, that when the electric field direction is parallel to the bridging C–C bonds of the 2C₆₀ molecule the 2C₆₀ fails easily, and that when the electric field direction is perpendicular to the 2C₆₀ fails difficultly and has the same polarization and failure mechanism as the single C₆₀.     

Germanium‐ and Silicon‐Substituted Donor–Acceptor Type Copolymers: Effect of the Bridging Heteroatom on Molecular Packing and Photovoltaic Device Performance

The effects of heteroatom substitution from a silicon atom to a germanium atom in donor‐acceptor type low band gap copolymers, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (PSiBTBT) and poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]germole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (PGeBTBT), are studied. The optoelectronic and charge transport properties of these polymers are investigated with a particular focus on their use for organic photovoltaic (OPV) devices in blends with phenyl‐C₇₀‐butyric acid methyl ester (PC₇₀BM). It is found that the longer C‐Ge bond length, in comparison to C‐Si, modifies the molecular conformation and leads to a more planar chain conformation in PGeBTBT than PSiBTBT. This increase in molecular planarity leads to enhanced crystallinity and an increased preference for a face‐on backbone orientation, thus leading to higher charge carrier mobility in the diode configuration. These results provide important insight into the impact of the heavy atom substitution on the molecular packing and device performance of polymers based on the poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole) (PCPDTBT) backbone.     

Light‐Induced Degradation of Polymer:Fullerene Photovoltaic Devices: An Intrinsic or Material‐Dependent Failure Mechanism?

Although degradation mechanisms in organic photovoltaic devices continue to receive increased attention, it is only recently that the initial light‐induced failure, or so‐called burn‐in effect, has been considered. Both prototypical polythiophene:fullerene and polycarbazole:fullerene systems exhibit an exponential performance loss of ≈40% upon 150 h of continuous solar illumination. While the decrease in both the short‐circuit current (J_SC) and open‐circuit voltage (V_OC) is the origin of performance loss in poly(3‐hexylthiophene):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PC₆₀BM), in poly(N‐9′‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)):[6,6]‐phenyl‐C71‐butyric acid methyl ester (PCDTBT:PC₇₀BM) the decline of the fill factor dominates. By systematic variation of the interface layers, active layer thickness, and acceptor in polythiophene:fullerene cells, the loss in J_SC is ascribed to a degradation in the bulk of the P3HT:PC₆₀BM, while the drop in V_OC is reversible and arises from charge trapping at the contact interfaces. By replacing the C₆₀ fullerene derivative with a C₇₀ derivative, or by modifying the electron transport layer, the J_SC or V_OC, respectively, are stabilized. These insights prove that the burn‐in process stems from multiple concurrent failure mechanisms. Comparing the ageing and recovery processes in P3HT and PCDTBT blends results in the conclusion that their interface failures differ in nature and that burn‐in is a material dependent, rather than an intrinsic, failure mechanism.     

Relating Recombination,Density of States,and Device Performance in an Efficient Polymer:Fullerene Organic Solar Cell Blend

We explore the interrelation between density of states, recombination kinetics, and device performance in efficient poly[4,8‐bis‐(2‐ethylhexyloxy)‐benzo[1,2‐b:4,5‐b']dithiophene‐2,6‐diyl‐alt‐4‐(2‐ethylhexyloxy‐1‐one)thieno[3,4‐b]thiophene‐2,6‐diyl]:[6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PBDTTT‐C:PC₇₁BM) bulk‐heterojunction organic solar cells. We modulate the active‐layer density of states by varying the polymer:fullerene composition over a small range around the ratio that leads to the maximum solar cell efficiency (50–67 wt% PC₇₁BM). Using transient and steady‐state techniques, we find that nongeminate recombination limits the device efficiency and, moreover, that increasing the PC₇₁BM content simultaneously increases the carrier lifetime and drift mobility in contrast to the behavior expected for Langevin recombination. Changes in electronic properties with fullerene content are accompanied by a significant change in the magnitude or energetic separation of the density of localized states. Our comprehensive approach to understanding device performance represents significant progress in understanding what limits these high‐efficiency polymer:fullerene systems.     

A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Plasmonic Back Reflectors: A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Quantitative analysis of C60 fullerene in blood and tissues by high-performance liquid chromatography with photodiode-array and mass spectrometric detection

A high-performance liquid chromatographic (HPLC) assay method for C₆₀ fullerene, in blood, liver and spleen using photodiode-array detection or mass spectrometric detection (LC–MS) and C₇₀ fullerene, as the internal standard, is described. The recovery from mouse blood and tissues spiked with micronized C₆₀ exceeds 90%. The method is linear from 0.05 to 200 mg of C₆₀ per liter of blood and from 0.05 to 5.00% of C₆₀ per tissue weight. The limit of detection of the method is 0.1 ng of C₆₀ per injection. This method was applied to mouse blood and tissue samples after intraperitoneal administration of a micronized C₆₀ suspension.     

8.9% Single‐Stack Inverted Polymer Solar Cells with Electron‐Rich Polymer Nanolayer‐Modified Inorganic Electron‐Collecting Buffer Layers

Enhanced power conversion efficiency (PCE) is reported in inverted polymer solar cells when an electron‐rich polymer nanolayer (poly(ethyleneimine) (PEI)) is placed on the surface of an electron‐collecting buffer layer (ZnO). The active layer is made with bulk heterojunction films of poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]] (PTB7) and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM). The thickness of the PEI nanolayer is controlled to be 2 nm to minimize its insulating effect, which is confirmed by X‐ray photoelectron spectroscopy and optical absorption measurements. The Kelvin probe and ultraviolet photoelectron spectroscopy measurements demonstrate that the enhanced PCE by introducing the PEI nanolayer is attributed to the lowered conduction band energy of the ZnO layer via the formation of an interfacial dipole layer at the interfaces between the ZnO layer and the PEI nanolayer. The PEI nanolayer also improves the surface roughness of the ZnO layer so that the device series resistance can be noticeably decreased. As a result, all solar cell parameters including short circuit current density, open circuit voltage, fill factor, and shunt resistance are improved, leading to the PCE increase up to ≈8.9%, which is close to the best PCE reported using conjugated polymer electrolyte films.     

The Crucial Influence of Fullerene Phases on Photogeneration in Organic Bulk Heterojunction Solar Cells

The conjugated polymer, poly(2,5‐bis(3‐hexadecylthiophen‐2‐yl)thieno[3,2‐b]thiophene) (pBTTT‐C₁₆), allows a systematic tuning of the blend morphology by varying the acceptor type and fraction, making it a well‐suited structural model for studying the fundamental processes in organic bulk heterojunction solar cells. To analyze the role of intercalated and pure fullerene domains on charge carrier photogeneration, time delayed collection field (TDCF) measurements and Fourier‐transform photocurrent spectroscopy (FTPS) are performed on pBTTT‐C₁₆:[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) solar cells with various stoichiometries. A weak influence of excess photon energy on photogeneration along with a photogeneration having a weaker field dependence at increasing fullerene loading is found. The findings are assigned to a dissociation via thermalized charge transfer (CT) states supported by an enhanced electron delocalization along spatially extended PC₆₁BM nanophases that form in addition to a bimolecular crystal (BMC) for PC₆₁BM rich blends. The highly efficient transfer of charge carriers from the BMC into the pure domains are studied further by TDCF measurements performed on non‐intercalated pBTTT‐C₁₆:bisPC₆₁BM blends. They reveal a field dependent charge generation similar to the 1:4 PC₆₁BM blend, demonstrating that the presence of pure acceptor phases is the major driving force for an efficient, field independent CT dissociation.