Morphology‐Dependent Trap Formation in High Performance Polymer Bulk Heterojunction Solar Cells

Bulk heterojunction solar cells (BHJs) based on poly[N‐9″‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT) can have internal quantum efficiencies approaching 100% but require active layers that are too thin to absorb more than ～70% of the above band gap light. When the active layer thickness is increased so that the cell absorbs more light, the fill factor and open circuit voltage decrease rapidly, so that the overall power conversion efficiency decreases. We find that hole‐traps in the polymer, which we characterize using space‐charge limited current measurements, play an important role in the performance of PCDTBT‐based BHJs and may limit the active layer thickness. Recombination due to carrier trapping is not often considered in BHJs because it is not believed to be a dominant loss mechanism in the “fruit‐fly” P3HT system. Furthermore, we show that in contrast to P3HT, PCDTBT has only weak short‐range molecular order, and that annealing at temperatures above the glass transition decreases the order in the π–π stacking. The decrease in structural order is matched by the movement of hole‐traps deeper into the band gap, so that thermal annealing worsens hole transport in the polymer and reduces the efficiency of PCDTBT‐based BHJs. These findings suggest that P3HT is not prototypical of the new class of high efficiency polymers, and that further improvement of BHJ efficiencies will necessitate the study of high efficiency polymers with low structural order.     

Batch‐to‐Batch Variation of Polymeric Photovoltaic Materials: its Origin and Impacts on Charge Carrier Transport and Device Performances

A detailed investigation of the impact of molecular weight distribution of a photoactive polymer, poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT), on photovoltaic device performance and carrier transport properties is reported. It is found that different batches of as‐received polymers have substantial differences in their molecular weight distribution. As revealed by gel permeation chromatography (GPC), two peaks can generally be observed. One of the peaks corresponds to a high molecular weight component and the other peak corresponds to a low molecular weight component. Photovoltaic devices fabricated with a higher proportion of low molecular weight component have power conversion efficiencies (PCEs) reduced from 5.7% to 2.5%. The corresponding charge carrier mobility at the short‐circuit region is also significantly reduced from 2.7 × 10^?5 to 1.6 × 10^?8 cm² V^?1 s^?1. The carrier transport properties of the polymers at various temperatures are further analyzed by the Gaussian disorder model (GDM). All polymers have similar energetic disorders. However, they appear to have significant differences in carrier hopping distances. This result provides insight into the origin of the molecular weight effect on carrier transport in polymeric semiconducting materials.     

Doping‐Induced Screening of the Built‐in‐Field in Organic Solar Cells: Effect on Charge Transport and Recombination

We report on the effects of screening of the electric field by doping‐induced mobile charges on photocurrent collection in operational organic solar cells. Charge transport and recombination were studied using double injection (DI) and charge extraction by linearly increasing voltage (CELIV) transient techniques in bulk‐heterojunction solar cells made from acceptor‐donor blends of poly(3‐n‐hexylthiophene):phenyl‐C61‐butyric acid methyl ester (P3HT:PC60BM). It is shown that the screening of the built‐in field in operational solar cells can be controlled by an external voltage while the influence on charge transport and recombination is measured. An analytical theory to extract the bimolecular recombination coefficient as a function of electric field from the injection current is also reported. The results demonstrate that the suppressed (non‐Langevin) bimolecular recombination rate and charge collection are not strongly affected by native doping levels in this materials combination. Hence, it is not necessary to reduce the level of doping further to improve the device performance of P3HT‐based solar cells.     

Trade‐Off between Trap Filling,Trap Creation,and Charge Recombination Results in Performance Increase at Ultralow Doping Levels in Bulk Heterojunction Solar Cells

Doping of organic bulk heterojunction solar cells has the potential to improve their power conversion efficiency (PCE). Deconvoluting the effect of doping on charge transport, recombination, and energetic disorder remains challenging. It is demonstrated that molecular doping has two competing effects: on one hand, dopant ions create additional traps while on the other hand free dopant‐induced charges fill deep states possibly leading to V _OC and mobility increases. It is shown that molar dopant concentrations as low as a few parts per million can improve the PCE of organic bulk heterojunctions. Higher concentrations degrade the performance of the cells. In doped cells where PCE is observed to increase, such improvement cannot be attributed to better charge transport. Instead, the V _OC increase in unannealed P3HT:PCBM cells upon doping is indeed due to trap filling, while for annealed P3HT:PCBM cells the change in V _OC is related to morphology changes and dopant segregation. In PCDTBT:PC70BM cells, the enhanced PCE upon doping is explained by changes in the thickness of the active layer. This study highlights the complexity of bulk doping in organic solar cells due to the generally low doping efficiency and the constraint on doping concentrations to avoid carrier recombination and adverse morphology changes.     

How Photoinduced Crosslinking Under Operating Conditions Can Reduce PCDTBT‐Based Solar Cell Efficiency and then Stabilize It

Bulk heterojunction (BHJ) photovoltaic devices made of PCDTBT (poly[N‐9′‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)]) and PC₇₀BM ([6,6]‐phenyl‐C₇₀‐butyric acid methyl ester) are among the most efficient and stable devices studied so far. However, during a short regime called “burn‐in”, a significant decrease of power conversion efficiency was observed. A study of the photochemical mechanisms involved in the PCDTBT:PCBM active layer exposed to light in encapsulated systems is presented. It is found that the photochemical reactions resulting from the absorption of light by PCDTBT involve crosslinking between the 2,7 carbazole unit of PCDTBT and the fullerene unit of PCBM. Those reactions stabilize the BHJ by avoiding the formation of microsized PCBM crystals known to cause failure of BHJ solar cells. Using classical electron paramagnetic resonance spectroscopy (EPR) (without illumination), paramagnetic defects along the polymer chains have been detected. The kinetics of defects intensity show a burn‐in trend. The evolution of their relaxation times upon aging is in good agreement with a structural change (crosslinking) of the BHJ observed from the nanomechanical properties. Finally, light‐induced electron paramagnetic resonance (LEPR) measurements performed on aged samples revealed that electron transfer is not significantly affected upon aging, confirming thus the stabilization of the BHJ in solar cell operating conditions.     

Plasmonic Backscattering Effect in High‐Efficient Organic Photovoltaic Devices

A universal strategy for efficient light trapping through the incorporation of gold nanorods on the electron transport layer (rear) of organic photovoltaic devices is demonstrated. Utilizing the photons that are transmitted through the active layer of a bulk heterojunction photovoltaic device and would otherwise be lost, a significant enhancement in power conversion efficiency (PCE) of poly[N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)]:phenyl‐C₇₁‐butyric acid methyl ester (PCDTBT:PC₇₁BM) and poly[[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b] thiophenediyl]] (PTB7):PC₇₁BM by ≈13% and ≈8%, respectively. PCEs over 8% are reported for devices based on the PTB7:PC₇₁BM blend. A comprehensive optical and electrical characterization of our devices to clarify the influence of gold nanorods on exciton generation, dissociation, charge recombination, and transport inside the thin film devices is performed. By correlating the experimental data with detailed numerical simulations, the near‐field and far‐field scattering effects are separated of gold nanorods (Au NRs), and confidently attribute part of the performance enhancement to the enhanced absorption caused by backscattering. While, a secondary contribution from the Au NRs that partially protrude inside the active layer and exhibit strong near‐fields due to localized surface plasmon resonance effects is also observed but is minor in magnitude. Furthermore, another important contribution to the enhanced performance is electrical in nature and comes from the increased charge collection probability.     

Excitation Dynamics in Low Band Gap Donor–Acceptor Copolymers and Blends

Donor–acceptor (D–A) type copolymers show great potential for the application in the active layer of organic solar cells. Nevertheless the nature of the excited states, the coupling mechanism and the relaxation pathways following photoexcitation are yet to be clarified. We carried out comparative measurements of the steady state absorption and photoluminescence (PL) on the copolymer poly[N‐(1‐octylnonyl)‐2,7‐carbazole]‐alt‐5,5‐[4′,7′‐di(thien‐2‐yl)‐2′,1′,3′‐benzothiadiazole] (PCDTBT), its building blocks as well as on the newly synthesized N‐(1‐octylnonyl)‐2,7‐bis‐[(5‐phenyl)thien‐2‐yl)carbazole (BPT‐carbazole). The high‐energy absorption band (HEB) of PCDTBT was identified with absorption of carbazoles with adjacent thiophene rings while the low‐energy band (LEB) originates instead from the charge transfer (CT) state delocalized over the aforementioned unit with adjacent benzothiadiazole group. Photoexcitation of the HEB is followed by internal relaxation prior the radiative decay to the ground state. Adding PC₇₀BM results in the efficient PL quenching within the first 50 ps after excitation. From the PL excitation experiments no evidence for a direct electron transfer from the HEB of PCDTBT towards the fullerene acceptor was found, therefore the internal relaxation mechanisms within PCDTBT can be assumed to precede. Our findings indicate that effective coupling between copolymer building blocks governs the photovoltaic performance of the blends.     

Charge Transport and Recombination in Low‐Bandgap Bulk Heterojunction Solar Cell using Bis‐adduct Fullerene

Charge transport and recombination are studied for organic solar cells fabricated using blends of polymer poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,5′‐diyl] (Si‐PCPDTBT) with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (mono‐PCBM) and the bis‐adduct analogue of mono‐PCBM (bis‐PCBM). The photocurrent of Si‐PCPDTBT:bis‐PCBM devices shows a strong square root dependence on the effective applied voltage. From the relationship between the photocurrent and the light intensity, we found that the square‐root dependence of the photocurrent is governed by the mobility‐lifetime (μτ) product of charge carriers while space‐charge field effects are insignificant. The fill factor (FF) and short circuit current density (J_sc) of bis‐PCBM solar cells show a considerable increase with temperature as compared to mono‐PCBM solar cells. SCLC analysis of single carrier devices proofs that the mobility of both electrons and holes is significantly lowered when replacing mono‐PCBM with bis‐PCBM. The increased recombination in Si‐PCPDTBT:bis‐PCBM solar cells is therefore attributed to the low carrier mobilities, as the transient photovoltage measurements show that the carrier lifetime of devices are not significantly altered by using bis‐PCBM instead of mono‐PCBM.     

Impact of UV‐Visible Light on the Morphological and Photochemical Behavior of a Low‐Bandgap Poly(2,7‐Carbazole) Derivative for Use in High‐Performance Solar Cells

This paper reports on the photochemical behavior upon exposure to UV‐visible light of a poly(2,7‐carbazole) derivative for use in high‐performance solar cells. Poly[N‐9′‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)] (PCDTBT) is one of a relatively large class of push‐pull carbazole‐based copolymers that have been synthesized to better harvest the solar spectrum. The 2,7‐carbazole building block of PCDTBT is also used with different electron‐accepting units in a large variety of low‐band‐gap polymers. The photochemical and morphological behavior of PCDTBT thin films is investigated from the molecular scale to the nanomechanical properties. The photo‐oxidation mechanism is shown to be governed by chain‐scission and cross‐linking reactions. It results in dramatic evolution of the morphology, roughness and stiffness of thin PCDTBT films. Based on the identification of several photoproducts formed along the macromolecular chains or released into the gas phase, the main pathways of PCDTBT photochemical evolution are discussed. These processes first involve the scission of the C–N bond between the carbazole group and the tertiary carbon atom bearing the alkyl side‐chain. Modifications of the chemical structure of PCDTBT, the evolution of its UV‐visible absorbance, and its nanomechanical properties initiated by light irradiation are shown to be closely related.     

Morphology‐Limited Free Carrier Generation in Donor/Acceptor Polymer Blend Solar Cells Composed of Poly(3‐hexylthiophene) and Fluorene‐Based Copolymer

The charge generation and recombination dynamics in polymer/polymer blend solar cells composed of poly(3‐hexylthiophene) (P3HT, electron donor) and poly[2,7‐(9,9‐didodecylfluorene)‐alt‐5,5‐(4′,7′‐bis(2‐thienyl)‐2′,1′,3′‐benzothiadiazole)] (PF12TBT, electron acceptor) are studied by transient absorption measurements. In the unannealed blend film, charge carriers are efficiently generated from polymer excitons, but some of them recombine geminately. In the blend film annealed at 160 °C, on the other hand, the geminate recombination loss is suppressed and hence free carrier generation efficiency increases up to 74%. These findings suggest that P3HT and PF12TBT are intermixed within a few nanometers, resulting in impure PF12TBT and disordered P3HT domains. The geminate recombination is likely due to charge carriers generated on isolated polymer chains in the matrix of the other polymer and at the domain interface with disordered P3HT. The undesired charge loss by geminate recombination is reduced by both the purification of the PF12TBT‐rich domain and crystallization of the P3HT chains. These results show that efficient free carrier generation is not inherent to the polymer/fullerene domain interface, but is possible with polymer/polymer systems composed of crystalline donor and amorphous acceptor polymers, opening up a new potential method for the improvement of solar cell materials.     

Light‐Induced Degradation of Polymer:Fullerene Photovoltaic Devices: An Intrinsic or Material‐Dependent Failure Mechanism?

Although degradation mechanisms in organic photovoltaic devices continue to receive increased attention, it is only recently that the initial light‐induced failure, or so‐called burn‐in effect, has been considered. Both prototypical polythiophene:fullerene and polycarbazole:fullerene systems exhibit an exponential performance loss of ≈40% upon 150 h of continuous solar illumination. While the decrease in both the short‐circuit current (J_SC) and open‐circuit voltage (V_OC) is the origin of performance loss in poly(3‐hexylthiophene):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PC₆₀BM), in poly(N‐9′‐hepta‐decanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole)):[6,6]‐phenyl‐C71‐butyric acid methyl ester (PCDTBT:PC₇₀BM) the decline of the fill factor dominates. By systematic variation of the interface layers, active layer thickness, and acceptor in polythiophene:fullerene cells, the loss in J_SC is ascribed to a degradation in the bulk of the P3HT:PC₆₀BM, while the drop in V_OC is reversible and arises from charge trapping at the contact interfaces. By replacing the C₆₀ fullerene derivative with a C₇₀ derivative, or by modifying the electron transport layer, the J_SC or V_OC, respectively, are stabilized. These insights prove that the burn‐in process stems from multiple concurrent failure mechanisms. Comparing the ageing and recovery processes in P3HT and PCDTBT blends results in the conclusion that their interface failures differ in nature and that burn‐in is a material dependent, rather than an intrinsic, failure mechanism.     

Fabricating High Performance,Donor–Acceptor Copolymer Solar Cells by Spray‐Coating in Air

We report the fabrication of high performance organic solar cells by spray‐coating the photoactive layer in air. The photovoltaic blends consist of a blend of carbazole and benzothiadiazole based donor–acceptor copolymers and the fullerene derivative PC₇₀BM. Here, we formulate a number of photovoltaic inks using a range of solvent systems that we show can all be deposited by spray casting. We use a range of techniques to characterize the structure of such films, and show that spray‐cast films have comparable surface roughness to spin‐cast films and that vertical stratification that occurs during film drying reduces the concentration of PCBM towards the underlying PEDOT:PSS interface. We also show that the active layer thickness and the drying kinetics can be tuned through control of the substrate temperature. High power conversion efficiencies of 4.3%, 4.5% and 4.6% were obtained for solar cells made from a blend of PC₇₀BM with the carbazole‐based co‐polymers PCDTBT, P2 and P1. By applying a low temperature anneal after the deposition of the cathode, the efficiency of spray‐cast solar‐cells based on a P2:PC₇₀BM blend is increased to 5.0%. Spray coating holds significant promise as a technique capable of fabricating large‐area, high performance organic solar cells in air.     

Recombination Losses Above and Below the Transport Percolation Threshold in Bulk Heterojunction Organic Solar Cells

Achieving the highest power conversion efficiencies in bulk heterojunction organic solar cells requires a morphology that delivers electron and hole percolation pathways for optimized transport, plus sufficient donor:acceptor contact area for near unity charge transfer state formation. This is a significant structural challenge, particularly in semiconducting polymer:fullerene systems. This balancing act in the model high efficiency PTB7:PC70BM blend is studied by tuning the donor:acceptor ratio, with a view to understanding the recombination loss mechanisms above and below the fullerene transport percolation threshold. The internal quantum efficiency is found to be strongly correlated to the slower carrier mobility in agreement with other recent studies. Furthermore, second‐order recombination losses dominate the shape of the current density–voltage curve in efficient blend combinations, where the fullerene phase is percolated. However, below the charge transport percolation threshold, there is an electric‐field dependence of first‐order losses, which includes electric‐field‐dependent photogeneration. In the intermediate regime, the fill factor appears to be limited by both first‐ and second‐order losses. These findings provide additional basic understanding of the interplay between the bulk heterojunction morphology and the order of recombination in organic solar cells. They also shed light on the limitations of widely used transport models below the percolation threshold.     

Investigating the Influence of Interfacial Contact Properties on Open Circuit Voltages in Organic Photovoltaic Performance: Work Function Versus Selectivity

The role of work function and thermodynamic selectivity of hole collecting contacts on the origin of open circuit voltage (V_OC) in bulk heterojunction organic photovoltaics is examined for poly(N‐9′‐heptadecanyl‐2,7‐carbazole‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole) (PCDTBT) and [6,6]‐phenyl‐C₇₁ butyric acid methyl ester (PC₇₁BM) solar cells. In the absence of a charge selective, electron blocking contact, systematic variation of the work function of the contact directly dictates the V_OC, as defined by the energetic separation between the relative Fermi levels for holes and electrons, with little change in the observed dark saturation current, J₀. Improving the charge selectivity of the contact through an increased barrier to electron injection from the fullerene in the blend into the hole contact results in a decreased reverse saturation current (decreased J₀ and increased shunt resistance, R_SH) and improved V_OC. Based on these observations, we provide a set of contact design criteria for tuning the V_OC in bulk heterojunction organic photovoltaics.     

Relation of Nanostructure and Recombination Dynamics in a Low‐Temperature Solution‐Processed CuInS2 Nanocrystalline Solar Cell

The understanding and control of nanostructures with regard to transport and recombination mechanisms is of key importance in the optimization of the power conversion efficiency (PCE) of solar cells based on inorganic nanocrystals. Here, the transport properties of solution‐processed solar cells are investigated using photo‐CELIV (photogenerated charge carrier extraction by linearly increasing voltage) and transient photovoltage techniques; the solar cells are prepared by an in‐situ formation of CuInS₂ nanocrystals (CIS NCs) at the low temperature of 270 °C. Structural and morphological analyses reveal the presence of a metastable CuIn₅S₈ phase and a disordered morphology in the CuInS₂ nanocrytalline films consisting of polycrystalline grains at the nanoscale range. Consistent with the disordered morphology of the CIS NC thin films, the CIS NC devices are characterized by a low carrier mobility. The carrier density dynamic indicates that the recombination kinetics in these devices follows the dispersive bimolecular recombination model and does not fully behave in a diffusion‐controlled manner, as expected by Langevin‐type recombination. The mobility–lifetime product of the charge carriers properly explains the performance of the thin (200 nm) CIS NC solar cell with a high fill‐factor of 64% and a PCE of over 3.5%.     

Facile Synthesis of Polycyclic Aromatic Hydrocarbon (PAH)–Based Acceptors with Fine‐Tuned Optoelectronic Properties: Toward Efficient Additive‐Free Nonfullerene Organic Solar Cells

A series of polycyclic aromatic hydrocarbons (PAHs) with extended π‐conjugated cores (from naphthalene, anthracene, pyrene, to perylene) are incorporated into nonfullerene acceptors for the first time. Four different fused‐ring electron acceptors (FREAs), i.e., DTN‐IC‐2Ph , DTA‐IC‐3Ph , DTP‐IC‐4Ph , and DTPy‐IC‐5Ph , are prepared via simple and facile synthetic procedures, yielding a remarkable platform to study the structure–property relationship for nonfullerene solar cells. With the PAH core being extended systematically, the gradually redshifted absorption with enhanced molar extinction coefficient (ε) is realized, the energy level of the highest occupied molecular orbital is up‐shifted, and the electron mobility is greatly enhanced. Meanwhile, the solubility decreases and the molecular packing becomes strengthened. As a result, with an optimized combination of these characteristics, DTP‐IC‐4Ph attains good solubility, high molar extinction coefficient, complementary absorption, suitable morphology, well‐matched energy levels, as well as efficient charge dissociation and transport in blend film. Consequently, the DTP‐IC‐4Ph ‐based solar cells with a donor polymer, poly[(2,6‐(4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene))‐alt‐(5,5‐(1′,3′‐di‐2‐thienyl‐5′,7′‐bis(2‐ethylhexyl)benzo[1′,2′‐c:4′,5′‐c′]dithiophene‐4,8‐dione))] (PBDB‐T) exhibit a promising power conversion efficiency of 10.37% without any additives, which is close to the best performance achieved in additive‐free nonfullerene solar cells (NFSCs). The results demonstrate that the PAH building blocks have great potential for the construction of novel FREAs for efficient additive‐free NFSCs.     

The Effect of PCBM Dimerization on the Performance of Bulk Heterojunction Solar Cells

Increasing the lifetime of polymer based organic solar cells is still a major challenge. Here, the photostability of bulk heterojunction solar cells based on the polymer poly[4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐[2,5‐bis(3‐tetradecylthiophen‐2‐yl)thiazole[5,4‐d]thiazole)‐1,8‐diyl] (PDTSTzTz) and the fullerene [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₀BM) under inert atmosphere is investigated. Correlation of electrical measurements on complete devices and UV‐vis absorption measurements as well as high‐performance liquid chromatography (HPLC) analysis on the active materials reveals that photodimerization of PC₆₀BM is responsible for the observed degradation. Simulation of the electrical device parameters shows that this dimerization results in a significant reduction of the charge carrier mobility. Both the dimerization and the associated device performance loss turn out to be reversible upon annealing. BisPC₆₀BM, the bis‐substituted analog of PC₆₀BM, is shown to be resistant towards light exposure, which in turn enables the manufacture of photostable PDTSTzTz:bisPC₆₀BM solar cells.     

Germanium‐ and Silicon‐Substituted Donor–Acceptor Type Copolymers: Effect of the Bridging Heteroatom on Molecular Packing and Photovoltaic Device Performance

The effects of heteroatom substitution from a silicon atom to a germanium atom in donor‐acceptor type low band gap copolymers, poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (PSiBTBT) and poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]germole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (PGeBTBT), are studied. The optoelectronic and charge transport properties of these polymers are investigated with a particular focus on their use for organic photovoltaic (OPV) devices in blends with phenyl‐C₇₀‐butyric acid methyl ester (PC₇₀BM). It is found that the longer C‐Ge bond length, in comparison to C‐Si, modifies the molecular conformation and leads to a more planar chain conformation in PGeBTBT than PSiBTBT. This increase in molecular planarity leads to enhanced crystallinity and an increased preference for a face‐on backbone orientation, thus leading to higher charge carrier mobility in the diode configuration. These results provide important insight into the impact of the heavy atom substitution on the molecular packing and device performance of polymers based on the poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole) (PCPDTBT) backbone.     

A Shockley‐Type Polymer: Fullerene Solar Cell

Charge extraction rate in solar cells made of blends of electron donating/accepting organic semiconductors is typically slow due to their low charge carrier mobility. This sets a limit on the active layer thickness and has hindered the industrialization of organic solar cells (OSCs). Herein, charge transport and recombination properties of an efficient polymer (NT812):fullerene blend are investigated. This system delivers power conversion efficiency of >9% even when the junction thickness is as large as 800 nm. Experimental results indicate that this material system exhibits exceptionally low bimolecular recombination constant, 800 times smaller than the diffusion‐controlled electron and hole encounter rate. Comparing theoretical results based on a recently introduced modified Shockley model for fill factor, and experiments, clarifies that charge collection is nearly ideal in these solar cells even when the thickness is several hundreds of nanometer. This is the first realization of high‐efficiency Shockley‐type organic solar cells with junction thicknesses suitable for scaling up.     

A Thieno[3,2‐c]Isoquinolin‐5(4H)‐One Building Block for Efficient Thick‐Film Solar Cells

An aromatic lactam acceptor unit, thieno[3,2‐c]isoquinolin‐5(4H)‐one (TIQ), is developed. Compared with its analogues, dithieno[3,2‐b:2′,3′‐d]pyridin‐5(4H)‐one (DTP) and phenanthridin‐6(5H)‐one (PN), TIQ shows its advantage in constructing donor–acceptor (D–A) copolymers for efficient solar cells. TIQ‐based D–A copolymer PTIQ4TFBT delivers a power conversion efficiency (PCE) of 10.16% in polymer:fullerene solar cells, while those based on DTP and PN copolymers, PDTP4TFBT and PPN4TFBT, afford PCEs around 8.5%. The higher performance of PTIQ4TFBT:PC₇₁BM solar cells originates from enhanced short‐circuit current density (J_sc) and fill factor (FF), because of favorable morphology, less bimolecular recombination, and balanced charge transport in the active layer. Moreover, the performance for PTIQ4TFBT:PC₇₁BM solar cells is less sensitive to active layer thickness than PDTP4TFBT:PC₇₁BM and PPN4TFBT:PC₇₁BM solar cells. Over 8% PCEs can be obtained from PTIQ4TFBT:PC₇₁BM solar cells when the active layer thickness is over 500 nm.