Efficiency Enhancement of Organic Solar Cells Using Hydrophobic Antireflective Inverted Moth‐Eye Nanopatterned PDMS Films

Poly‐dimethylsiloxane (PDMS) films with 2D periodic inverted moth‐eye nanopatterns on one surface are implemented as antireflection (AR) layers on a glass substrate for efficient light capture in encapsulated organic solar cells (OSCs). The inverted moth‐eye nanopatterned PDMS (IMN PDMS) films are fabricated by a soft imprint lithographic method using conical subwavelength grating patterns formed by laser interference lithography/dry etching. Their optical characteristics, together with theoretical analysis using rigorous coupled‐wave analysis simulation, and wetting behaviors are investigated. For a period of 380 nm, IMN PDMS films laminated on glass substrates exhibit a hydrophobic surface with a water contact angle (θ_CA) of ≈120° and solar weighted transmittance (SWT) of ≈94.2%, both significantly higher than those (θ_CA≈ 36° and SWT ≈ 90.3%) of bare glass substrates. By employing IMN PDMS films with a period of 380 nm on glass substrates for OSCs, an enhanced power conversion efficiency (PCE) of 6.19% is obtained mainly due to the increased short‐circuit current density (J_sc) of 19.74 mA cm^‐2 compared to the OSCs with the bare glass substrates (PCE = 5.16% and J_sc = 17.25 mA cm^‐2). For the OSCs, the device stability is also studied.     

High Performance Flexible Transparent Electrode via One‐Step Multifunctional Treatment for Ag Nanonetwork Composites Semi‐Embedded in Low‐Temperature‐Processed Substrate for Highly Performed Organic Photovoltaics

For ideal flexible transparent electrodes, the features of good electrical/optical properties, low surface roughness, efficient charge transportation, robust electrical stability under simultaneously continuous operation bias, and mechanical bending are critical. Herein, a flexible transparent electrode fulfilling all these features is demonstrated by silver (Ag) nanonetwork composites semi‐embedded in low‐temperature‐processed colorless polyimide (cPI), which shows a figure of merit over 1000 (5.4 Ω sq^?1 sheet resistance and >94% diffused transmission at 550 nm wavelength), extremely smooth topography (<1 nm root‐mean‐square roughness and <3 nm peak‐to‐valley roughness), remarkable bending stability under continuous operation bias, and increased work function favoring the band alignment with typical charge transport layers for efficient devices. These characteristics are attributed to one‐step multifunctional chemical treatment on the composite of Ag nanowires and an example polymer of poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS). The strategic one‐step process simultaneously offers selective welding at nanowires cross junctions to form an Ag nanonetwork, and removing polyvinylpyrrolidone surfactant from Ag nanowires and PSS from PEDOT:PSS. The flexible electrode also favors the residue‐free cPI transfer for applications. Flexible organic solar cells (OSCs) made from the electrode achieve an averaged power conversion efficiency of 14.46% (best, 15.12%), which is the best flexible OSCs reported so far.     

Highly Efficient Sunlight‐Driven Seawater Splitting in a Photoelectrochemical Cell with Chlorine Evolved at Nanostructured WO3 Photoanode and Hydrogen Stored as Hydride within Metallic Cathode

A seawater splitting photoelectrochemical cell featuring a nanostructured tungsten trioxide photoanode that exhibits very high and stable photocurrents producing chlorine with average 70% Faradaic efficiency is described. Fabrication of the WO₃ electrodes on fluorine‐doped tin oxide substrates involves a simple solution‐based method and sequential layer‐by‐layer deposition with a progressively adjusted amount of structure‐directing agent in the precursor and a two‐step annealing. Such a procedure allows tailoring of thick, highly porous, structurally stable WO₃ films with a large internal photoactive surface area optimizing utilization of visible light wavelengths by the photoanode. With the application of an anodic potential of 0.76 V versus Ag/AgCl reference electrode (0.4 V below the thermodynamic Cl₂/Cl^? potential) in synthetic seawater, the designed WO₃ photoanodes irradiated with simulated 1 sun AM 1.5G light reach currents exceeding 4.5 mA cm^?2. Photocurrents close to 5 mA cm^?2 are attained in the case of fresh water splitting using 1 m methane–sulfonic acid supporting electrolyte with oxygen evolved at the WO₃ photoanode. The amount of formed hydrogen is determined by discharging the palladium sheet electrode employed as a cathode. Collection of hydrogen in the form of a hydride opens, more generally, the prospect of subsequently using such materials as anodes in batteries employing oxygen reduction cathodes.     

Significant Effect of Fluorination on Simultaneously Improving Work Function and Transparency of Anode Interlayer for Organic Solar Cells

Since the highest occupied molecular orbital (HOMO) level of donors in organic solar cells (OSCs) is being constantly downshifted for achieving high open‐circuit voltage (V_oc), a further enhancement of the anode work function (WF) is required. Herein, an effective approach of fluorination is demonstrated to simultaneously improve the WF and transparency for anode interlayer (AIL) material. By fluorination, in combination with the dialysis treatment in LiCl solution, the WF of PCP‐2F‐Li could be significantly enhanced from 4.86 to 5.0 eV, as compared to PCP‐Na. Meanwhile, the transparency of the polymer is also improved. As a result, PCP‐2F‐Li can be used to modify efficient active layers consisting of polymer donors with deep HOMO levels, such as PBDB‐T‐2F:IT‐4F, and an outstanding power conversion efficiency (PCE) of 12.7% is achieved in the corresponding device with a high V_oc of 0.84 V. This result represents the highest efficiency for the OSCs using a solution‐processed pH‐neutral AIL, which is beneficial to the low‐cost fabrication of high‐performance OSCs with improved stability. More importantly, PCP‐2F‐Li could be processed by blade coating for making large‐area device of 1 cm², and a PCE of 10.6% is achieved, bringing a promising prospect for the large‐area device fabrication.     

Boosting the Performance of WO3/n‐Si Heterostructures for Photoelectrochemical Water Splitting: from the Role of Si to Interface Engineering

Metal oxide/Si heterostructures make up an exciting design route to high‐performance electrodes for photoelectrochemical (PEC) water splitting. By monochromatic light sources, contributions of the individual layers in WO₃/n‐Si heterostructures are untangled. It shows that band bending near the WO₃/n‐Si interface is instrumental in charge separation and transport, and in generating a photovoltage that drives the PEC process. A thin metal layer inserted at the WO₃/n‐Si interface helps in establishing the relation among the band bending depth, the photovoltage, and the PEC activity. This discovery breaks with the dominant Z‐scheme design idea, which focuses on increasing the conductivity of an interface layer to facilitate charge transport, but ignores the potential profile around the interface. Based on the analysis, a high‐work‐function metal is predicted to provide the best interface layer in WO₃/n‐Si heterojunctions. Indeed, the fabricated WO₃/Pt/n‐Si photoelectrodes exhibit a 2 times higher photocurrent density at 1.23 V versus reversible hydrogen electrode (RHE) and a 10 times enhancement at 1.6 V versus RHE compared to WO₃/n‐Si. Here, it is essential that the native SiO₂ layer at the interface between Si and the metal is kept in order to prevent Fermi level pinning in the Schottky contact between the Si and the metal.     

Polyoxometalate‐Derived Ultrasmall Pt2W/WO3 Heterostructure Outperforms Platinum for Large‐Current‐Density H2 Evolution

Platinum (Pt)‐based catalysts with high Pt utilization efficiency for efficient H₂ evolution are attracting extensive attention to meet the issues of energy exhaustion and environmental pollution. Herein, a one‐step electrochemical method is demonstrated to construct ultrafine heterostructure Pt₂W/WO₃ on reduced graphene oxide (RGO) by injecting multielectrons into the Preyssler anion [NaP₅W₃₀O₁₁₀]^14? to codeposit with anodic deliquescent Pt cations. The resulting Pt₂W/WO₃/RGO shows much higher performance than that of commercial Pt catalysts for large‐current‐density H₂ evolution, which can deliver a large current density of 500 mA cm^?2 with an overpotential of only 394 mV, much lower than that of 20% Pt/C (578 mV). Comparisons with control experiments and density functional theory (DFT) calculations both suggest that the much enhanced activity can be mainly attributed to the synergistic cooperation of different components to drive fast and continuous hydrogen desorption on Pt₂W/WO₃/RGO, while it could not run normally for 20% Pt/C under similar conditions due to the formation of huge bubbles on the electrode surface. The effective integration of high catalytic activity and hydrogen desorption ability into a single material can yield advanced materials for large‐current‐density H₂ evolution with remarkable stability.     

ZnWO4:Eu3+ phosphor with intense blue LED excitation: photoluminescence and electron density distribution analysis

A high intensity 464 nm excitable ZnWO₄:Eu³⁺ red‐emitting phosphor for warm white lighting applications was prepared using a solid‐state reaction method by varying the dopant Eu³⁺ concentration. Crystalline purity and phase identification was confirmed and revealed using powder X‐ray diffraction and Rietveld refinement analysis. The surface morphology of Zn_1‐xEu_xWO₄ (x = 0, 0.01, 0.02, 0.03, 0.04 and 0.05) was examined using scanning electron microscopy (SEM) techniques. From SEM analysis, the ZnWO₄:Eu³⁺ phosphor prepared at 1–3% molar Eu³⁺ concentrations exhibited a small pebble‐like morphology with a smooth surface. On increasing the molar concentration of Eu³⁺ to >3%, the pebble stone morphology disappeared and a large, smooth irregular polygon‐shaped granular‐like morphology was obtained. Of the higher mol% Eu³⁺, the 4% Eu³⁺‐doped ZnWO₄ showed the best photoluminescence properties with high intensity and sharp excitation at 395 and 464 nm, followed by red emission centred at 615 nm with excellent CIE coordinates (x = 0.58 and y = 0.41) in the core red region. Elemental composition and chemical state analysis were carried out for the 4% Eu³⁺‐doped ZnWO₄ phosphor using X‐ray photoelectron spectroscopy and energy dispersive X‐ray spectroscopy studies. Based on all the above analyses, the Eu³⁺‐doped ZnWO₄ phosphor was found to be a very efficient red‐emitting phosphor under near‐UV light as well as under visible light excitation and could be used for white LED and field emissive displays applications.     

High‐Performance Ta2O5/Al‐Doped Ag Electrode for Resonant Light Harvesting in Efficient Organic Solar Cells

A efficient indium tin oxide (ITO)‐free transparent electrode based on an improved Ag film is designed by introducing small amount of Al during co‐deposition, producing ultrathin and smooth Ag film with low loss. A transparent electrode as thin as 4 nm is achieved by depositing the film on top of Ta₂O₅ layer, and organic solar cells based on such ultrathin electrode are built, producing power conversion efficiency over 7%. The device efficiency can be optimized by simply tuning Ta₂O₅ layer thickness external to the organic photovoltaic (OPV) structure to create an optical cavity resonance inside the photoactive layer. Therefore Ta₂O₅/Al‐doped Ag films function as a high‐performance electrode with high transparency, low resistance, improved photon management capability and mechanical flexibility.     

Operando Oxygen Vacancies for Enhanced Activity and Stability toward Nitrogen Photofixation

Photocatalysts with oxygen vacancies (OVs) have exhibited exciting activity in N₂ photofixation due to their superiority in capture and activation of N₂. However, the surface OVs are easily oxidized by seizing the oxygen atoms from water or oxygen during the catalytic reaction. Here, it is reported that the grain boundaries (GBs) in nanoporous WO₃ induce plenty of operando OVs under light irradiation to significantly boost catalytic activity toward N₂ photofixation. Impressively, nanoporous WO₃ with abundant GBs (WO₃‐600) exhibit an ammonia production rate of 230 µmol g_cat.^?1 h^?1 without any sacrificial agents at room temperature, 17 times higher than that for WO₃ nanoparticles without GBs. Moreover, WO₃‐600 also manifests remarkable stability by maintaining nearly ≈100% catalytic activity after ten successive reaction rounds. Further mechanistic studies reveal that both OVs and GBs regulate the band structures of WO₃ nanocrystals, as well as favor the delivery of photogenerated electrons to adsorbed N₂ by enhancing W–O covalency. More importantly, plenty of operando OVs induced by GBs generate during catalytic reaction, directly contributing to the excellent catalytic performance for WO₃‐600. This work opens a novel avenue to developing efficient photocatalysts by construction of operando OVs.     

SrTiO3/Al2O3‐Graphene Electron Transport Layer for Highly Stable and Efficient Composites‐Based Perovskite Solar Cells with 20.6% Efficiency

For practical use of perovskite solar cells (PSCs) the instability issues of devices, attributed to degradation of perovskite molecules by moisture, ions migration, and thermal‐ and light‐instability, have to be solved. Herein, highly efficient and stable PSCs based on perovskite/Ag‐reduced graphene oxide (Ag‐rGO) and mesoporous Al₂O₃/graphene (mp‐AG) composites are reported. The mp‐AG composite is conductive with one‐order of magnitude higher mobility than mp‐TiO₂ and used for electron transport layer (ETL). Compared to the mp‐TiO₂ ETL based cells, the champion device based on perovskite/Ag‐rGO and SrTiO₃/mp‐AG composites shows overall a best performance (i.e., V_OC = 1.057 V, J_SC = 25.75 mA cm^?2, fill factor (FF) = 75.63%, and power conversion efficiency (PCE) = 20.58%). More importantly, the champion device without encapsulation exhibits not only remarkable thermal‐ and photostability but also long‐term stability, retaining 97–99% of the initial values of photovoltaic parameters and sustaining ≈93% of initial PCE over 300 d under ambient conditions.     

Overcoming Charge Collection Limitation at Solid/Liquid Interface by a Controllable Crystal Deficient Overlayer

Bulk and surface charge recombination of photoelectrode are two key processes that significantly hinder solar‐to‐fuel conversion of photoelectrochemical cell (PEC). In this study, the function of a “crystal‐deficient” overlayer is unveiled, which outperforms a traditionally used amorphous or crystalline overlayer in PEC water splitting by exhibiting a high conductivity and large electron diffusion length to enable unlimited electron collection. The optimized ≈2.5 nm thickness of the “crystal‐deficient” shell results in a depletion layer with a width of 3 nm, which overcomes the flat band limitation of the photovoltage and increases the light absorptivity in the wavelength range from 300 to 420 nm. In addition, a 50‐fold increase in the conductivity yields a one‐order‐of‐magnitude increase in the diffusion length of an electron (L_n )(≈20 μm), allowing for unlimited electron collection in the 1.9 μm TiO₂ nanowire array with the “crystal‐deficient” shell. The controllable “crystal‐deficient” overlayer in rutile TiO₂ nanowires photoanode achieves a photocurrent density greater than 2.0 mA cm^?2 at 1.23 V versus reversible hydrogen electrode (RHE), a 1.18% applied bias photon‐to‐current efficiency at 0.49 V versus RHE, a faradaic efficiency greater than 93.5% at 0.6 V versus Pt under air mass 1.5G simulated solar light illumination (100 mW cm^?2).     

Barium Bismuth Niobate Double Perovskite/Tungsten Oxide Nanosheet Photoanode for High‐Performance Photoelectrochemical Water Splitting

Recently, a new method to effectively engineer the bandgap of barium bismuth niobate (BBNO) double perovskite was reported. However, the planar electrodes based on BBNO thin films show low photocurrent densities for water oxidation owing to their poor electrical conductivity. Here, it is reported that the photoelectrochemical (PEC) activity of BBNO‐based electrodes can be dramatically enhanced by coating thin BBNO layers on tungsten oxide (WO₃) nanosheets to solve the poor conductivity issue while maintaining strong light absorption. The PEC activity of BBNO/WO₃ nanosheet photoanodes can be further enhanced by applying Co_0.8Mn_0.2O_x nanoparticles as a co‐catalyst. A photocurrent density of 6.02 mA cm^?2 at 1.23 V (vs reversible hydrogen electrode (RHE)) is obtained using three optically stacked, but electrically parallel, BBNO/WO₃ nanosheet photoanodes. The BBNO/WO₃ nanosheet photoanodes also exhibit excellent stability in a high‐pH alkaline solution; the photoanodes demonstrate negligible photocurrent density decay while under continuous PEC operation for more than 7 h. This work suggests a viable approach to improve the PEC performance of BBNO absorber‐based devices.     

Stability of Nonfullerene Organic Solar Cells: from Built‐in Potential and Interfacial Passivation Perspectives

Remarkable progress has been made in the development of high‐efficiency solution‐processable nonfullerene organic solar cells (OSCs). However, the effect of the vertical stratification of bulk heterojunction (BHJ) on the efficiency and stability of nonfullerene OSCs is not fully understood yet. In this work, we report our effort to understand the stability of nonfullerene OSCs, made with the binary blend poly[(2,6‐(4, 8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)‐benzo[1,2‐b:4,5‐b′]dithiophene))‐alt‐(5,5‐(1′,3′‐di‐2‐thienyl‐5′,7′‐bis(2‐ethylhexyl)benzo[1′,2′‐c:4′,5′‐c′] dithiophene‐4,8‐dione)] (PBDB‐T):3,9‐ bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐ dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′] dithiophene (ITIC) system. It shows that a continuous vertical phase separation process occurs, forming a PBDB‐T‐rich top surface and an ITIC‐rich bottom surface in PBDB‐T:ITIC BHJ during the aging period. A gradual decrease in the built‐in potential (V₀) in the regular configuration PBDB‐T:ITIC OSCs, due to the interfacial reaction between the poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT:PSS) hole transporting layer and ITIC acceptor, is one of the reasons responsible for the performance deterioration. The reduction in V₀, caused by an inevitable reaction at the ITIC/PEDOT:PSS interface in the OSCs, can be suppressed by introducing a MoO₃ interfacial passivation layer. Retaining a stable and high V₀ across the BHJ through interfacial modification and device engineering, e.g., as seen in the inverted PBDB‐T:ITIC OSCs, is a prerequisite for efficient and stable operation of nonfullerene OSCs.     

One-Step Preparation and Fluorescence Enhancement Effect in SiO2/Eu2+ Doped with Ag Nanowires

Eu²⁺ single-doped SiO₂ (SiO₂/Eu²⁺) and Eu²⁺, Ag nanowires co-doped SiO₂ (SiO₂/Eu²⁺–Ag) luminescent nanomaterials were prepared by an efficient one-step sol–gel method. Their microstructure and optical properties were characterized, and the fluorescence enhancement of Eu²⁺ by Ag nanowires was investigated. The experimental results indicate that the average diameter of Ag nanowires doped is 12.5 nm, and the length–diameter ratio is 30. The Ag nanowires cannot only enhance the light absorption of SiO₂/Eu²⁺ in the range of 230–350 nm, but also reduce the fluorescence lifetime of Eu²⁺. More importantly, the emission intensity is enhanced after doping Ag nanowires, and the red shift phenomenon of the emission spectrum is observed, red shift occurs between 10 and 56 nm. The highest fluorescence intensity is accessed under the Ag doping concentration of 0.10 %. Additionally, the emission of SiO₂/Eu²⁺ with 0.10 % of Ag doping at 456 nm is 16 times stronger than that of pure SiO₂/Eu²⁺. The present results indicate that the fluorescence enhancement is attributed to the local field enhancement and the increased radiative decay rates induced by Ag nanowires.     

Highly Stable Transparent Conductive Silver Grid/PEDOT:PSS Electrodes for Integrated Bifunctional Flexible Electrochromic Supercapacitors

Silver grids are attractive for replacing indium tin oxide as flexible transparent conductors. This work aims to improve the electrochemical stability of silver‐based transparent conductors. A silver grid/PEDOT:PSS hybrid film with high conductivity and excellent stability is successfully fabricated. Its functionality for flexible electrochromic applications is demonstrated by coating one layer of WO₃ nanoparticles on the silver grid/PEDOT:PSS hybrid film. This hybrid structure presents a large optical modulation of 81.9% at 633 nm, fast switching, and high coloration efficiency (124.5 cm² C^?1). More importantly, an excellent electrochemical cycling stability (sustaining 79.1% of their initial transmittance modulation after 1000 cycles) and remarkable mechanical flexibility (optical modulation decay of only 7.5% after 1200 compressive bending cycles) is achieved. A novel smart supercapacitor is presented that functions as a regular energy‐storage device and simultaneously monitors the level of stored energy by a rapid and reversible color variation even at high current charge/discharge conditions. The film sustains an optical modulation of 87.7% and a specific capacitance of 67.2% at 10 A g^?1 compared to their initial value at a current density of 1 A g^?1. The high‐performance silver grid/PEDOT:PSS hybrid transparent films exhibit promising features for various emerging flexible electronics and optoelectronic devices.     

Enhanced Stability of Li Metal Anodes by Synergetic Control of Nucleation and the Solid Electrolyte Interphase

Use of a protective coating on a lithium metal anode (LMA) is an effective approach to enhance its coulombic efficiency and cycling stability. Here, a facile approach to produce uniform silver nanoparticle‐decorated LMA for high‐performance Li metal batteries (LMBs) is reported. This effective treatment can lead to well‐controlled nucleation and the formation of a stable solid electrolyte interphase (SEI). Ag nanoparticles embedded in the surface of Li anodes induce uniform Li plating/stripping morphologies with reduced overpotential. More importantly, cross‐linked lithium fluoride‐rich interphase formed during Ag⁺ reduction enables a highly stable SEI layer. Based on the Ag‐LiF decorated anodes, LMBs with LiNi_1/3Mn_1/3Co_1/3O₂ cathode (≈1.8 mAh cm^?2) can retain >80% capacity over 500 cycles. The similar approach can also be used to treat sodium metal anodes. Excellent stability (80% capacity retention in 10 000 cycles) is obtained for a Na||Na₃V₂(PO₄)₃ full cell using a Na‐Ag‐NaF/Na anode cycled in carbonate electrolyte. These results clearly indicate that synergetic control of the nucleation and SEI is an efficient approach to stabilize rechargeable metal batteries.     

Recognition of silver nanoparticles surface‐adsorbed citrate anions by macrocyclic polyammonium cations: a spectrophotometric approach to study aggregation kinetics and evaluation of association constant

In this report, we have studied the recognition of citrate anions adsorbed on the surface of silver nanoparticles (cit‐Ag‐NPs), by macrocyclic polyammonium cations (MCPACs): Me₆[14]ane‐N₄H₈⁴⁺ (Tet‐A/Tet‐B cations) and [32]ane‐N₈H₁₆⁸⁺, which are well reputed anion recognizers and are treated as to mimic of biological polyamines. The study was monitored on ultraviolet–visible spectroscopy by performing a titration of the aqueous dispersion of the cit‐Ag‐NPs by the aqueous solution of MCPACs. The ultraviolet–visible time‐scan plots over the reduction of the absorption band of surface plasmon resonance of cit‐Ag‐NPs at 390 nm are well fitted with fourth‐order polynomial equation and are employed to determine the initial aggregation rate constants. It has been stated that the aggregation is the result in electrostatic attraction followed by H‐bond formation between the surface‐adsorbed citrate anions and added MCPACs. The atomic force microscopy results have evidenced aggregation of cit‐Ag‐NPs in presence of MCPACs. The evaluated H‐bonded association constant (K_asso) using Benesi–Hildebrand method reveals that [32]ane‐N₈H₁₆⁸⁺ cations form stronger association complex, as expected, with the citrate anions than the Me₆[14]ane‐N₄H₈⁴⁺ cations. The study would thus provide the insight of molecular interactions involved in nanoparticle surface‐adsorbed anions with biological polyamines. Copyright © 2016 John Wiley & Sons, Ltd.     

Evaporation‐Free Nonfullerene Flexible Organic Solar Cell Modules Manufactured by An All‐Solution Process

To ensure laboratory‐to‐industry transfer of next‐generation energy harvesting organic solar cells (OSCs), it is necessary to develop flexible OSC modules that can be produced on a continuous roll‐to‐roll basis and to apply an all‐solution process. In this study, nonfullerene acceptors (NFAs)‐based donor polymer, SMD2, is newly designed and synthesized to continuously fabricate high‐performance flexible OSC modules. Also, multifunctional hole transport layers (HTLs), WO₃/HTL solar bilayer HTLs, are developed and applied via an all‐solution process called “ProcessOne” into inverted structure. SMD2, the donor terpolymer, has a deep highest occupied molecular orbital (HOMO) level and can achieve a power conversion efficiency (PCE) of 11.3% with NFAs without any pre‐/post‐treatment because of its optimal balance between crystallinity and miscibility. Furthermore, the integration of multifunctional HTLs enables the recovery of the drop in open circuit voltage (V_OC) caused by a mismatch in energy levels between the deep HOMO level of the NFAs‐based bulk‐heterojunction layer and the solution‐processed HTLs. Also, the photostability under ultraviolet‐exposure necessary for “ProcessOne” is greatly improved because of the integration of multifunctional HTLs. Consequently, because of the synergistic effects of these approaches, the flexible OSC modules fabricated in an industrial production line have a PCE of 5.25% (P_max = 419.6 mW) on an active area of 80 cm².     

Sn‐Alloy Foil Electrode with Mechanical Prelithiation: Full‐Cell Performance up to 200 Cycles

Self‐supporting Sn foil is a promising high‐volumetric‐capacity anode for lithium ion batteries (LIBs), but it suffers from low initial Coulombic efficiency (ICE). Here, mechanical prelithiation is adopted to improve ICE, and it is found that Sn foils with coarser grains are prone to cause electrode damage. To mitigate damage and prepare thinner lithiated electrodes, 3Ag0.5Cu96.5Sn foil is used that has more refined grains (5–10 µm) instead of Sn (50–100 µm), where the abundant grain boundaries (GBs) offer more sliding systems to release stress and reduce deep fractures. Thus, the thickness of Li_x3Ag0.5Cu96.5Sn can be reduced to 50 µm, compared to 100 µm Li_xSn. When the foils contact open air, the Sn‐Li‐O(H) products are more stable than Li‐O(H), thus Li_x3Ag0.5Cu96.5Sn shows outstanding air stability. The as‐prepared 50 µm foil anode achieves stable 200 cycles in LiFePO₄//Li_x3Ag0.5Cu96.5Sn full cell (≈2.65 mAh cm^?2) and the capacity retention is 95%. Even at 5C, the capacity of Li_x3Ag0.5Cu96.5Sn is still up to ≈1.8 mAh cm^?2. The cycle life of NCM523//Li_x3Ag0.5Cu96.5Sn full cell exceeds that of NCM523//Li. Furthermore, 70 µm Li_x3Ag0.5Cu96.5Sn is used as double‐sided anode for a 3 cm × 2.8 cm pouch cell and its actual volumetric capacity density is 674 mAh cm^?3 after 50 cycles.     

Bandgap Narrowing in Non‐Fullerene Acceptors: Single Atom Substitution Leads to High Optoelectronic Response Beyond 1000 nm

Two narrow bandgap non‐fullerene acceptors (NBG‐NFAs), namely, COTIC‐4F and SiOTIC‐4F, are designed and synthesized for the fabrication of efficient near‐infrared organic solar cells (OSCs). The chemical structures of the NBG‐NFAs contain a D′‐D‐D′ electron‐rich internal core based on a cyclopentadithiophene (or dithienosilole) (D) and alkoxythienyl (D′) core, end‐capped with the highly electron‐deficient unit 2‐(5,6‐difluoro‐3‐oxo‐2,3‐dihydro‐1H‐inden‐1‐ylidene)malononitrile (A), ultimately providing a A‐D′‐D‐D′‐A molecular configuration that enhances the intramolecular charge transfer characteristics of the excited states. One can thereby reduce the optical bandgap (E_g^opt) to as low as ≈1.10 eV, one of the smallest values for NFAs reported to date. In bulk‐heterojunction (BHJ) OSCs, NBG‐NFA blends with the polymer donor PTB7‐Th yield power conversion efficiencies (PCE) of up to 9.0%, which is particularly high when compared against a range of NBG BHJ blends. Most significantly, it is found that, despite the small energy loss (E_g^opt ? eV_OC) of 0.52 eV, the PTB7‐Th/NBG‐NFA bulk heterojunction blends can yield short‐circuit current densities of up to 22.8 mA cm^?2, suggesting that the design and application of NBG‐NFA materials have substantial potential to further improve the PCE of OSCs.