Silicon Composite Electrodes with Dynamic Ionic Bonding

Silicon (Si) composite electrodes are developed with increased cycle lifetimes and reliability through dynamic ionic bonding between active Si nanoparticles and a polymer binder. Amine groups are covalently attached to Si nanoparticles via surface functionalization. Si composite electrodes are fabricated by combining the Si nanoparticles with a poly(acrylic acid) (PAA) binder. The formation of ionic bonds between amine groups on Si particles and carboxylic acid groups on the PAA binder is characterized by X‐ray photoelectron spectroscopy and Raman spectroscopy. Si composite anodes with ionic bonding demonstrate long term cycling stability with capacity retention of 80% at 400 cycles at a current density of 2.1 A g^?1 and good rate capability. The dynamic ionic bonds effectively mitigate the deterioration of electrical interfaces in the composite anodes as suggested by stable impedance over 300 cycles.     

Galvanic Corrosion of Lithium‐Powder‐Based Electrodes

Lithium metal is considered to be the most promising anode for the next generation of batteries if the issues related to safety and low coulombic efficiency can be overcome. It is known that the initial morphology of the lithium metal anode has a great influence on the cycling characteristics of a lithium metal battery (LMB). Lithium‐powder‐based electrodes (Li_p‐electrodes) are reported to diminish the occurrence of high surface area lithium deposits. Usually, ultra‐thin lithium foils (<50 µm) and Li_p‐electrodes are prepared on a copper substrate, thus a metal–metal contact area is generated. The combination of these two metals in the presence of an electrolyte, however, can lead to galvanic corrosion. Herein, the corrosion behavior of Li_p‐electrodes is studied. The porosity of such electrodes leads to a high amount of accessible Cu surface in contact with electrolyte. As a consequence, Li_p‐electrodes aged for 1 week in the electrolyte show spontaneous lithium dissolution near the junction to copper and void formation on the lithium‐powder particles. This corrosion process affects the delivered capacity of Li_p‐electrodes and increases the overvoltage of the lithium electrodissolution process. The occurrence of corrosion at the Cu|Li_p interface raises concerns about the practicality of multi‐metallic component systems for LMBs.     

Extremely Flexible Transparent Conducting Electrodes for Organic Devices

Extremely flexible transparent conducting electrodes are developed using a combination of metal‐embedding architecture into plastic substrate and ultrathin transparent electrodes, which leads to highly transparent (optical transmittance ≈93% at a wavelength of 550 nm), highly conducting (sheet resistance ≈13 Ω □^?1), and extremely flexible (bending radius ≈ 200 μm) electrodes. The electrodes are used to fabricate flexible organic solar cells and organic light‐emitting diodes that exhibit performance similar or superior to that of devices fabricated on glass substrates. Moreover, the flexible devices do not show degradation in their performance even after being folded with a radius of ≈200 μm.     

Iron‐Based Supercapacitor Electrodes: Advances and Challenges

Supercapacitors (SCs) have great promise as the state‐of‐the‐art power source in portable electronics and hybrid vehicles. The performance of SCs is largely determined by the properties of the electrode material, and numerous efforts have been devoted to the explorations of novel electrode materials. Recently, iron‐based materials, including Fe₂O₃, Fe₃O₄, FeOOH, FeO_x, CoFe₂O₄, and MnFe₂O₄, have received considerable attention as very promising electrode materials for SCs due to their high theoretical specific capacitances, natural abundance, low cost, and non‐toxicity. However, most of these Fe‐based SC electrodes suffer from poor conductivity and/or electrochemical instability, which seriously impede their implementation as high‐performance electrodes for SCs. To settle these issues, substantial efforts have been made in improving their conductivity and cycling stability, and great processes have been achieved. Here, recent research advances in the rational design and synthesis of diverse Fe‐based nanostructured electrodes and their capacitive performance for SCs are presented. Besides, challenges and prospects of Fe‐based materials as advanced negative electrodes for SCs are also discussed.     

Pseudocapacitive Charge Storage in Thick Composite MoS2 Nanocrystal‐Based Electrodes

A synthesis methodology is demonstrated to produce MoS₂ nanoparticles with an expanded atomic lamellar structure that are ideal for Faradaic‐based capacitive charge storage. While much of the work on MoS₂ focuses on the high capacity conversion reaction, that process is prone to poor reversibility. The pseudocapacitive intercalation‐based charge storage reaction of MoS₂ is investigated, which is extremely fast and highly reversible. A major challenge in the field of pseudocapacitive‐based energy storage is the development of thick electrodes from nanostructured materials that can sustain the fast inherent kinetics of the active nanocrystalline material. Here a composite electrode comprised of a poly(acrylic acid) binder, carbon fibers, and carbon black additives is utilized. These electrodes deliver a specific capacity of 90 mAh g^?1 in less than 20 s and can be cycled 3000 times while retaining over 80% of the original capacity. Quantitative kinetic analysis indicates that over 80% of the charge storage in these MoS₂ nanocrystals is pseudocapacitive. Asymmetric full cell devices utilizing a MoS₂ nanocrystal‐based electrode and an activated carbon electrode achieve a maximum power density of 5.3 kW kg^?1 (with 6 Wh kg^?1 energy density) and a maximum energy density of 37 Wh kg^?1 (with 74 W kg^?1power density).     

Multimodal Nanoscale Tomographic Imaging for Battery Electrodes

Accurate representations of the 3D structure within a lithium‐ion battery are key to understanding performance limitations. However, obtaining exact reconstructions of electrodes, where the active particles, the carbon black and polymeric binder domain, and the pore space are visualized is challenging. Here, it is shown that multimodal imaging can be used to overcome this challenge. High‐resolution ptychographic X‐ray computed tomography are combined with lower resolution but higher contrast transmission X‐ray tomographic microscopy to obtain 3D reconstructions of pristine and cycled graphite‐silicon composite electrodes. This cross‐correlation enables quantitative analysis of the surface of active particles, including the heterogeneity of carbon‐black and binder domain and solid‐electrolyte interphase coverage. Capturing the active particles as well as the carbon black‐binder domain allows using these segmented structures for electrochemical simulations to highlight the influence of the particle embedding on local state of charge heterogeneities.     

Nanoarchitectured Array Electrodes for Rechargeable Lithium‐ and Sodium‐Ion Batteries

Rechargeable ion batteries have contributed immensely to shaping the modern world and been seriously considered for the efficient storage and utilization of intermittent renewable energies. To fulfill their potential in the future market, superior battery performance of high capacity, great rate capability, and long lifespan is undoubtedly required. In the past decade, along with discovering new electrode materials, the focus has been shifting more and more toward rational electrode designs because the performance is intimately connected to the electrode architectures, particularly their designs at the nanoscale that can alleviate the reliance on the materials' intrinsic nature. The utilization of nanoarchitectured arrays in the design of electrodes has been proven to significantly improve the battery performance. A comprehensive summary of the structural features and fabrications of the nanoarchitectured array electrodes is provided, and some of the latest achievements in the area of both lithium‐ and sodium‐ion batteries are highlighted. Finally, future challenges and opportunities that would allow further development of such advanced electrode configuration are discussed.     

Graphitic Petal Electrodes for All‐Solid‐State Flexible Supercapacitors

The charge storage characteristics of a composite nanoarchitecture with a highly functional 3D morphology are reported. The electrodes are formed by the electropolymerization of aniline monomers into a nanometer‐thick polyaniline (PANI) film that conformally coats graphitic petals (GPs) grown by microwave plasma chemical vapor deposition (MPCVD) on conductive carbon cloth (CC). The hybrid CC/GPs/PANI electrodes yield results near the theoretical maximum capacitance for PANI of 2000 F g^?1 (based on PANI mass) and a large area‐normalized specific capacitance of ≈2.6 F cm^?2 (equivalent to a volumetric capacitance of ≈230 F cm^?3) at a low current density of 1 A g^?1 (based on PANI mass). The specific capacitances remain above 1200 F g^?1 (based on PANI mass) for currents up to 100 A g^?1 with correspondingly high area‐normalized values. The hybrid electrodes also exhibit a high rate capability with an energy density of 110 Wh kg^?1 and a maximum power density of 265 kW kg^?1 at a current density of 100 A g^?1. Long‐term cyclic stability is good (≈7% loss of initial capacitance after 2000 cycles), with coulombic efficiencies >99%. Moreover, prototype all‐solid‐state flexible supercapacitors fabricated from these hybrid electrodes exhibit excellent energy storage performance.     

Photoelectrochemical Behavior of Planar and Microwire‐Array Si|GaP Electrodes

Gallium phosphide exhibits a short diffusion length relative to its optical absorption length, and is thus a candidate for use in wire array geometries that allow light absorption to be decoupled from minority carrier collection. Herein is reported the photoanodic performance of heteroepitaxially grown gallium phosphide on planar and microwire‐array Si substrates. The n‐GaP|n‐Si heterojunction results in a favorable conduction band alignment for electron collection in the silicon. A conformal electrochemical contact to the outer GaP layer is produced using the ferrocenium/ferrocene (Fc⁺/Fc) redox couple in acetonitrile. Photovoltages of ～750 mV under 1 sun illumination are observed and are attributed to the barrier formed at the (Fc⁺/Fc)|n‐GaP junction. The short‐circuit current densities of the composite microwire‐arrays are similar to those observed using single‐crystal n‐GaP photoelectrodes. Spectral response measurements along with a finite‐difference‐time‐domain optical model indicate that the minority carrier diffusion length in the GaP is ～80 nm. Solid‐state current–voltage measurements show that shunting occurs through thin GaP layers that are present near the base of the microwire‐arrays. The results provide guidance for further studies of 3D multi‐junction photoelectrochemical cells.