Highly Efficient Aqueous‐Processed Hybrid Solar Cells: Control Depletion Region and Improve Carrier Extraction

Environmental friendly aqueous‐processed solar cells have become one of the most promising candidates for the next‐generation photovoltaic devices. Researchers have made lots of progress in designing active materials with novel structures, manipulating the defects in active materials, optimizing device architecture, etc. However, it has long been a challenge to control the width of the depletion region and enhance carrier extraction ability. Fabrication of a thick bulk heterojunction (BHJ) film is an effective strategy to address these issues but difficult to realize. Herein, the thicker BHJ film of ZnO:CdTe is successfully fabricated and incorporated into CdTe‐poly(p‐phenylenevinylene) hybrid solar cells. As expected, this BHJ film enhances light absorption, extends the width of the depletion region, prolongs carrier lifetime, and promotes carrier extraction ability. Moreover, the electron transport layer of sol–gel ZnO with excellent transmittance and electrical conductivity boosts electron generation, transport, and injection, which further improves the device performance. As a result, the highest short current density (J_sc) of 19.5 mA cm^?2, power conversion efficiency of 6.51%, and the widest depletion region (177 nm) are obtained in aqueous‐processed hybrid solar cells.     

Relation of Nanostructure and Recombination Dynamics in a Low‐Temperature Solution‐Processed CuInS2 Nanocrystalline Solar Cell

The understanding and control of nanostructures with regard to transport and recombination mechanisms is of key importance in the optimization of the power conversion efficiency (PCE) of solar cells based on inorganic nanocrystals. Here, the transport properties of solution‐processed solar cells are investigated using photo‐CELIV (photogenerated charge carrier extraction by linearly increasing voltage) and transient photovoltage techniques; the solar cells are prepared by an in‐situ formation of CuInS₂ nanocrystals (CIS NCs) at the low temperature of 270 °C. Structural and morphological analyses reveal the presence of a metastable CuIn₅S₈ phase and a disordered morphology in the CuInS₂ nanocrytalline films consisting of polycrystalline grains at the nanoscale range. Consistent with the disordered morphology of the CIS NC thin films, the CIS NC devices are characterized by a low carrier mobility. The carrier density dynamic indicates that the recombination kinetics in these devices follows the dispersive bimolecular recombination model and does not fully behave in a diffusion‐controlled manner, as expected by Langevin‐type recombination. The mobility–lifetime product of the charge carriers properly explains the performance of the thin (200 nm) CIS NC solar cell with a high fill‐factor of 64% and a PCE of over 3.5%.     

Aqueous‐Processed Polymer/Nanocrystal Hybrid Solar Cells with Double‐Side Bulk Heterojunction

Aqueous‐solution‐processed solar cells (ASCs) are promising candidates of the next‐generation large‐area, low‐cost, and flexible photovoltaic conversion equipment because of their unique environmental friendly property. Aqueous‐solution‐processed polymer/nanocrystals (NCs) hybrid solar cells (AHSCs) can effectively integrate the advantages of the polymer (e.g., flexibility and lightweight) and the inorganic NCs (e.g., high mobility and broad absorption), and therefore be considered as an ideal system to further improve the performance of ASCs. In this work, double‐side bulk heterojunction (BHJ), in which one BHJ combines the active material with electron transport material and the other combines the active material with hole transport material, is developed in the AHSCs. Through comparing with the single‐side BHJ device, promoted carrier extraction, enhanced internal quantum efficiency, extended width of the depletion region, and prolonged carrier lifetime are achieved in double‐side BHJ devices. As a result, power conversion efficiency exceeding 6% is obtained, which breaks the bottleneck efficiency around ≈5.5%. This work demonstrates a device architecture which is more remarkable compared with the traditional only donor–acceptor blended BHJ. Under conservative estimation, it provides instructive architecture not only in the ASCs, but also in the organic solar cells (SCs), quantum dot SCs, and perovskite SCs.     

Effects of Solvent Additives on Morphology,Charge Generation,Transport, and Recombination in Solution‐Processed Small‐Molecule Solar Cells

The effects of solvent additive (1,8‐diiodooctane (DIO)) on the morphology, charge generation, transport, and recombination in solution‐processed small‐molecule solar cells are studied and these parameters are correlated with device performance. In the optimum nanoscale morphology, which is processed with 0.4% DIO, the phase separation is large enough to create a percolating pathway for carrier transport, yet still small enough to form large interfacial area for efficient charge separation. Complete phase separation in this film reduces the interfacial defects, which occurs without DIO, and hence suppresses the monomolecular recombination. Moreover, balanced charge transport and weak bimolecular recombination lead to a high fill factor (72%). On the other hand, an excess amount of DIO (0.8%) in the solvent results in the over‐aggregation of the donor phase, which disturbs the percolating pathway of the acceptor phase and reduces the electron mobility. The over‐aggregation of the donor phase also shrinks the interfacial area for charge separation and consequently reduces the photocurrent generation.     

In Situ Phase‐Induced Spatial Charge Separation in Core–Shell Oxynitride Nanocube Heterojunctions Realizing Robust Solar Water Splitting

Efficient spatial charge separation is critical for solar energy conversion over solid photocatalysts. The development of efficient visible‐light photocatalysts has been of immense interest, but with limited success. Here, multiband core–shell oxynitride nanocube heterojunctions composed of a tantalum nitride (Ta₃N₅) core and nitrogen‐doped sodium tantalate (NaTaON) shell have been constructed via an in situ phase‐induced etching chemical strategy. The photocatalytic water splitting performance of sub‐20‐nm Ta₃N₅@NaTaON junctions exhibits an extraordinarily high photocatalytic activity toward oxygen and hydrogen evolution. Most importantly, the combined experimental results and theoretical calculations reveal that the strong interfacial Ta? O? N bonding connection as a touchstone among Ta₃N₅@NaTaON junctions provides a continuous charge transport pathway rather than a random charge accumulation. The prolonged photoexcited charge carrier lifetime and suitable band matching between the Ta₃N₅ core and NaTaON shell facilitate the separation of photoinduced electron–hole pairs, accounting for the highly efficient photocatalytic performance. This work establishes the use of (oxy)nitride heterojunctions as viable photocatalysts for the conversion of solar energy into fuels.     

Low‐Temperature Solution‐Processed CuCrO2 Hole‐Transporting Layer for Efficient and Photostable Perovskite Solar Cells

Organic–inorganic hybrid perovskite solar cells (PVSCs) have become the front‐running photovoltaic technology nowadays and are expected to profoundly impact society in the near future. However, their practical applications are currently hampered by the challenges of realizing high performance and long‐term stability simultaneously. Herein, the development of inverted PVSCs is reported based on low temperature solution‐processed CuCrO₂ nanocrystals as a hole‐transporting layer (HTL), to replace the extensively studied NiO_x counterpart due to its suitable electronic structure and charge carrier transporting properties. A ≈45 nm thick compact CuCrO₂ layer is incorporated into an inverted planar configuration of indium tin oxides (ITO)/c‐CuCrO₂/perovskite/[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM)/bathocuproine (BCP)/Ag, to result in the high steady‐state power conversion efficiency of 19.0% versus 17.1% for the typical low temperature solution‐processed NiO_x‐based devices. More importantly, the optimized CuCrO₂‐based device exhibits a much enhanced photostability than the reference device due to the greater UV light‐harvesting of the CuCrO₂ layer, which can efficiently prevent the perovskite film from intense UV light exposure to avoid associated degradation. The results demonstrate the promising potential of CuCrO₂ nanocrystals as an efficient HTL for realizing high‐performance and photostable inverted PVSCs.     

Direct Imaging of Cl‐ and Cu‐Induced Short‐Circuit Efficiency Changes in CdTe Solar Cells

To achieve high‐efficiency polycrystalline CdTe‐based thin‐film solar cells, the CdTe absorbers must go through a post‐deposition CdCl₂ heat treatment followed by a Cu diffusion step. To better understand the roles of each treatment with regard to improving grains, grain boundaries, and interfaces, CdTe solar cells with and without Cu diffusion and CdCl₂ heat treatments are investigated using cross‐sectional electron beam induced current, electron backscatter diffraction, and scanning transmission electron microscope techniques. The evolution of the cross‐sectional carrier collection profile due to these treatments that cause an increase in short‐circuit current and higher open‐circuit voltage are identified. Additionally, an increased carrier collection in grain boundaries after either/both of these treatments is revealed. The increased current at the grain boundaries is shown to be due to the presence of a space charge region with an intrinsic carrier collection profile width of ≈350 nm. Scanning transmission electron microscope electron‐energy loss spectroscopy shows a decreased Te and increased Cl concentration in grain boundaries after treatment, which causes the inversion. Each treatment improves the overall carrier collection efficiency of the cell separately, and, therefore, the benefits realized by each treatment are shown to be independent of each other.     

Controlling the Morphology and Efficiency of Hybrid ZnO:Polythiophene Solar Cells Via Side Chain Functionalization

The efficiency of polymer – metal oxide hybrid solar cells depends critically on the intimacy of mixing of the two semiconductors. The effect of side chain functionalization on the morphology and performance of conjugated polymer:ZnO solar cells is investigated. Using an ester‐functionalized side chain poly(3‐hexylthiophene‐2,5‐diyl) derivative (P3HT‐E), the nanoscale morphology of ZnO:polymer solar cells is significantly more intimately mixed compared to ZnO:poly(3‐hexylthiophene‐2,5‐diyl) (ZnO:P3HT), as evidenced experimentally from a 3D reconstruction of the phase separation using electron tomography. Photoinduced absorption reveals nearly quantitative charge generation for the ZnO:P3HT‐E blend but not for ZnO:P3HT, consistent with the results obtained from solving the 3D diffusion equation for excitons formed in the polymer within the two experimental ZnO morphologies. For thin ZnO:P3HT‐E active layers (～50 nm) this yields a significant improvement of the solar cell performance. For thicker cells, however, the reduced hole mobility and a reduced percolation of ZnO pathways hinders charge carrier collection, limiting the power conversion efficiency.     

A Shockley‐Type Polymer: Fullerene Solar Cell

Charge extraction rate in solar cells made of blends of electron donating/accepting organic semiconductors is typically slow due to their low charge carrier mobility. This sets a limit on the active layer thickness and has hindered the industrialization of organic solar cells (OSCs). Herein, charge transport and recombination properties of an efficient polymer (NT812):fullerene blend are investigated. This system delivers power conversion efficiency of >9% even when the junction thickness is as large as 800 nm. Experimental results indicate that this material system exhibits exceptionally low bimolecular recombination constant, 800 times smaller than the diffusion‐controlled electron and hole encounter rate. Comparing theoretical results based on a recently introduced modified Shockley model for fill factor, and experiments, clarifies that charge collection is nearly ideal in these solar cells even when the thickness is several hundreds of nanometer. This is the first realization of high‐efficiency Shockley‐type organic solar cells with junction thicknesses suitable for scaling up.     

Simple,Highly Efficient Vacuum‐Processed Bulk Heterojunction Solar Cells Based on Merocyanine Dyes

In order to be competitive on the energy market, organic solar cells with higher efficiency are needed. To date, polymer solar cells have retained the lead with efficiencies of up to 8%. However, research on small molecule solar cells has been catching up throughout recent years and is showing similar efficiencies, however, only for more sophisticated multilayer device configurations. In this work, a simple, highly efficient, vacuum‐processed small molecule solar cell based on merocyanine dyes – traditional colorants that can easily be mass‐produced and purified – is presented. In the past, merocyanines have been successfully introduced in solution‐processed as well as vacuum‐processed devices, demonstrating efficiencies up to 4.9%. Here, further optimization of devices is achieved while keeping the same simple layer stack, ultimately leading to efficiencies beyond the 6% mark. In addition, physical properties such as the charge carrier transport and the cell performance under various light intensities are addressed.     

Thiophene Rings Improve the Device Performance of Conjugated Polymers in Polymer Solar Cells with Thick Active Layers

Developing novel materials that tolerate thickness variations of the active layer is critical to further enhance the efficiency of polymer solar cells and enable large‐scale manufacturing. Presently, only a few polymers afford high efficiencies at active layer thickness exceeding 200 nm and molecular design guidelines for developing successful materials are lacking. It is thus highly desirable to identify structural factors that determine the performance of semiconducting conjugated polymers in thick‐film polymer solar cells. Here, it is demonstrated that thiophene rings, introduced in the backbone of alternating donor–acceptor type conjugated polymers, enhance the fill factor and overall efficiency for thick (>200 nm) solar cells. For a series of fluorinated semiconducting polymers derived from electron‐rich benzo[1,2‐b:4,5‐b′]dithiophene units and electron‐deficient 5,6‐difluorobenzo[2,1,3]thiazole units a steady increase of the fill factor and power conversion efficiency is found when introducing thiophene rings between the donor and acceptor units. The increased performance is a synergistic result of an enhanced hole mobility and a suppressed bimolecular charge recombination, which is attributed to more favorable polymer chain packing and finer phase separation.     

Enhancing the Internal Quantum Efficiency and Stability of Organic Solar Cells via Metallic Nanofunnels

Metal nanoparticles are demonstrated to boost the internal quantum efficiency (IQE) of organic solar cells (OSCs), even without a notable plasmonic optical gain. A hybrid layer platform in combination with silver nanoparticles (AgNPs) and a polyethylenimine‐ethoxylated (PEIE) layer maximize the IQE of the OSCs to nearly 100%, yielding a power conversion efficiency (PCE) of 10.1% in the OSCs. 2D surface characterization confirmed that the AgNPs provide a short path and funneled charge carriers to the cathode, thus effectively increasing the carrier mobility. Moreover, the hybrid layer doubles the device's half‐efficiency lifetime due to the longer retention of the improved mobility.     

Quantitative Analysis and Visualized Evidence for High Charge Separation Efficiency in a Solid‐Liquid Bulk Heterojunction

In the past few decades, some novel low‐cost nanostructured devices have been explored for converting solar energy into electrical or chemical energy, such as organic photovoltaic cells, photoelectrochemical solar cells, and solar water splitting cells. Generally, higher light absorption and/or charge separation efficiency are considered as the main reasons for improved performance in a nanostructured device versus a planar structure. However, quantitative analysis and definite experimental evidence remain elusive. Here, using BiVO₄ as an example, comparable samples with porous and dense structures have been prepared by a simple method. The porous and dense films are assembled into a solid‐electrolyte bulk and planar heterojunction, respectively. Some quantitative results are obtained by decoupling photon absorption, interfacial charge transfer, and charge separation processes. These results suggest that higher charge separation efficiency is mainly responsible for enhanced performance in a solid‐electrolyte bulk heterojunction. Moreover, we also present visualized evidence to show higher charge separation efficiency comes from a shorter photo‐generated hole diffusion distance in a bulk heterojunction. These results can deepen understanding charge transfer in a bulk heterojunction and offer guidance to design a more efficient low‐cost device for solar conversion and storage.     

Ethanedithiol Treatment of Solution‐Processed ZnO Thin Films: Controlling the Intragap States of Electron Transporting Interlayers for Efficient and Stable Inverted Organic Photovoltaics

The surface defects of solution‐processed ZnO films lead to various intragap states. When the solution‐processed ZnO films are used as electron transport interlayers (ETLs) in inverted organic solar cells, the intragap states act as interfacial recombination centers for photogenerated charges and thereby degrade the device performance. Here, a simple passivation method based on ethanedithiol (EDT) treatment is demonstrated, which effectively removes the surface defects of the ZnO nanocrystal films by forming zinc ethanedithiolates. The passivation by EDT treatment modulates the intragap states of the ZnO films and introduces a new intragap band. When the EDT‐treated ZnO nanocrystal films are used as ETLs in inverted organic solar cells, both the power conversion efficiency and stability of the devices are improved. The control studies show that the solar cells with EDT‐treated ZnO films exhibit reduced charge recombination rates and enhanced charge extraction properties. These features are consistent with the fact that the modulation of the intragap states results in reduction of interfacial recombination as well as the improved charge selectivity and electron transport properties of the ETLs. It is further demonstrated that the EDT treatment‐based passivation method can be extended to ZnO films deposited from sol–gel precursors.     

Rational Core–Shell Design of Open Air Low Temperature In Situ Processable CsPbI3 Quasi‐Nanocrystals for Stabilized p‐i‐n Solar Cells

As a promising alternative, inorganic perovskite nanocrystals allow reinforced stability of photovoltaic device. Unfortunately, directly assembling these nanocrystals into film is uncontrollable. Instead, in situ assembling technology under low temperature in open air is attractive but limited due to the tendency of nonperovskite transition. The adverse shell ligands and unstable core lattices are known as the fundamental problems. In order to address this issue, here proposed is a rational core–shell design: 1) with respect to ligands, a new one, 4‐fluorophenethylammonium iodide, is used to enhance bonding force and charge coupling between ligands and nanocrystals; 2) with respect to lattices, a novel compound H₂PbI₄ is employed to assist divalent ion (Mn²⁺) doping into perovskite lattices. By low temperature in situ processing CsPbI₃ quasi‐nanocrystal film, the highest power conversion efficiency of 13.4% for p‐i‐n solar cells is achieved, which retains 92% after 500 h in ambient air. The current study underlines the significance of rational hierarchical design of inorganic perovskite nanocrystals, especially for low temperature in situ processable electronic devices.     

Alkyl Chain Engineering of Solution‐Processable Star‐Shaped Molecules for High‐Performance Organic Solar Cells

The impact of alkyl side‐chain substituents on conjugated polymers on the photovoltaic properties of bulk heterojunction (BHJ) solar cells has been studied extensively, but their impact on small molecules has not received adequate attention. To reveal the effect of side chains, a series of star‐shaped molecules based on a triphenylamine (TPA) core, bithiophene, and dicyanovinyl units derivatized with various alkyl end‐capping groups of methyl, ethyl, hexyl and dodecyl is synthesiyed and studied to comprehensively investigate structure‐properties relationships. UV‐vis absorption and cyclic voltammetry data show that variations of alkyl chain length have little influence on the absorption and highest occupied molecular orbital (HOMO)‐lowest unoccupied molecular orbital (LUMO) levels. However, these seemingly negligible changes have a pronounced impact on the morphology of BHJ thin films as well as their charge carrier separation and transportation, which in turn influences the photovoltaic properties of these small‐molecule‐based BHJ devices. Solution‐processed organic solar cells (OSCs) based on the small molecule with the shortest methyl end groups exhibit high short circuit current (J_sc) and fill factor (FF), with an efficiency as high as 4.76% without any post‐treatments; these are among the highest reported for solution‐processed OSCs based on star‐shaped molecules.     

(040)‐Crystal Facet Engineering of BiVO4 Plate Photoanodes for Solar Fuel Production

A (040)‐crystal facet engineered BiVO₄ ((040)‐BVO) photoanode is investigated for solar fuel production. The (040)‐BVO photoanode is favorable for improved charge carrier mobility and high photocatalytic active sites for solar light energy conversion. This crystal facet design of the (040)‐BVO photoanode leads to an increase in the energy conversion efficiency for solar fuel production and an enhancement of the oxygen evolution rate. The photocurrent density of the (040)‐BVO photoanode is determined to be 0.94 mA cm^?2 under AM 1.5 G illumination and produces 42.1% of the absorbed photon‐to‐current conversion efficiency at 1.23 V (vs RHE, reversible hydrogen electrode). The enhanced charge separation efficiency and improved charge injection efficiency driven by (040) facet can produce hydrogen with 0.02 mmol h^?1 at 1.23 V. The correlation between the (040)‐BVO photoanode and the solar fuel production is investigated. The results provide a promising approach for the development of solar fuel production using a BiVO₄ photoanode.     

Steric Engineering of Alkylthiolation Side Chains to Finely Tune Miscibility in Nonfullerene Polymer Solar Cells

Morphology and miscibility control are still a great challenge in polymer solar cells. Despite physical tools being applied, chemical strategies are still limited and complex. To finely tune blend miscibility to obtain optimized morphology, chemical steric engineering is proposed to systemically investigate its effects on optical and electronic properties, especially on a balance between crystallinity and miscibility. By changing the alkylthiol side chain orientation different steric effects are realized in three different polymers. Surprisingly, the photovoltaic device of the polymer PTBB‐m with middle steric structure affords a better power conversion efficiency, over 12%, compared to those of the polymers PTBB‐o and PTBB‐p with large or small steric structures, which could be attributed to a more balanced blend miscibility without sacrificing charge‐carrier transport. Space charge‐limited current, atomic force microscopy, grazing incidence wide angle X‐ray scattering, and resonant soft X‐ray scattering measurements show that the steric engineering of alkylthiol side chains can have significant impacts on polymer aggregation properties, blend miscibility, and photovoltaic performances. More important, the control of miscibility via the simple chemical approach has preliminarily proved its great potential and will pave a new avenue for optimizing the blend morphology.     

Recombination Losses Above and Below the Transport Percolation Threshold in Bulk Heterojunction Organic Solar Cells

Achieving the highest power conversion efficiencies in bulk heterojunction organic solar cells requires a morphology that delivers electron and hole percolation pathways for optimized transport, plus sufficient donor:acceptor contact area for near unity charge transfer state formation. This is a significant structural challenge, particularly in semiconducting polymer:fullerene systems. This balancing act in the model high efficiency PTB7:PC70BM blend is studied by tuning the donor:acceptor ratio, with a view to understanding the recombination loss mechanisms above and below the fullerene transport percolation threshold. The internal quantum efficiency is found to be strongly correlated to the slower carrier mobility in agreement with other recent studies. Furthermore, second‐order recombination losses dominate the shape of the current density–voltage curve in efficient blend combinations, where the fullerene phase is percolated. However, below the charge transport percolation threshold, there is an electric‐field dependence of first‐order losses, which includes electric‐field‐dependent photogeneration. In the intermediate regime, the fill factor appears to be limited by both first‐ and second‐order losses. These findings provide additional basic understanding of the interplay between the bulk heterojunction morphology and the order of recombination in organic solar cells. They also shed light on the limitations of widely used transport models below the percolation threshold.     

Porphyrin‐Based Bulk Heterojunction Organic Photovoltaics: The Rise of the Colors of Life

Organic photovoltaics (OPV) represent a thin‐film PV technology that offers attractive prospects for low‐cost and aesthetically appealing (colored, flexible, uniform, semitransparent) solar cells that are printable on large surfaces. In bulk heterojunction (BHJ) OPV devices, organic electron donor and acceptor molecules are intimately mixed within the photoactive layer. Since 2005, the power conversion efficiency of said devices has increased substantially due to insights in the underlying physical processes, device optimization, and chemical engineering of a vast number of novel light‐harvesting organic materials, either small molecules or conjugated polymers. As Nature itself has developed porphyrin chromophores for solar light to energy conversion, it seems reasonable to pursue artificial systems based on the same types of molecules. Porphyrins and their analogues have already been successfully implemented in certain device types, notably in dye‐sensitized solar cells, but they have remained largely unexplored in BHJ organic solar cells. Very recent successes do show, however, the strong (latent) prospects of porphyrinoid semiconductors as light‐harvesting and charge transporting materials in such devices. Here, an overview on the state‐of‐the‐art of porphyrin‐based solution‐processed BHJ OPV is provided and insights are given into the pathways to follow and hurdles to overcome toward further improvements of porphyrinic materials and devices.