Membrane‐Free Zn/MnO2 Flow Battery for Large‐Scale Energy Storage

The traditional Zn/MnO₂ battery has attracted great interest due to its low cost, high safety, high output voltage, and environmental friendliness. However, it remains a big challenge to achieve long‐term stability, mainly owing to the poor reversibility of the cathode reaction. Different from previous studies where the cathode redox reaction of MnO₂/MnOOH is in solid state with limited reversibility, here a new aqueous rechargeable Zn/MnO₂ flow battery is constructed with dissolution–precipitation reactions in both cathodes (Mn²⁺/MnO₂) and anodes (Zn²⁺/Zn), which allow mixing of anolyte and catholyte into only one electrolyte and remove the requirement for an ion selective membrane for cost reduction. Impressively, this new battery exhibits a high discharge voltage of ≈1.78 V, good rate capability (10C discharge), and excellent cycling stability (1000 cycles without decay) at the areal capacity ranging from 0.5 to 2 mAh cm^‐2. More importantly, this battery can be readily enlarged to a bench scale flow cell of 1.2 Ah with good capacity retention of 89.7% at the 500th cycle, displaying great potential for large‐scale energy storage.     

Mulberry Paper‐Based Supercapacitor Exhibiting High Mechanical and Chemical Toughness for Large‐Scale Energy Storage Applications

In response to the demand for flexible and sustainable energy storage devices that exhibit high electrochemical performance, a supercapacitor system is fabricated using mulberry tree‐derived paper as a substrate and Poly(3,4‐ethylenedioxythiophene)‐poly(styrenesulfonate) (PEDOT:PSS) and carbon black as the active material. The mulberry paper‐based supercapacitor system demonstrates high energy density of 29.8–39.8 Wh kg^?1 and power density of 2.8–13.9 kW kg^?1 with 90.7% retention of its initial capacity over 15 000 charge–discharge cycles. In addition, the mulberry tree fibers are known to have superior mechanical strength and toughness and the mulberry paper‐based supercapacitor; as a result, exhibit high mechanical and chemical toughness; 99% of its initial capacity is retained after 100 repeated applications of bending strains, and twisting. 94% capacity retention is observed even after exposure to HCl and H₂SO₄ acid solutions. The fabrication methodology of the mulberry‐based supercapacitor is highly scalable and could be stacked to increase the energy storage capacity, where operation of light‐emitting diode lights with a drive voltage of 12 V integrated in a wearable device is demonstrated.     

Fatigue‐Free and Bending‐Endurable Flexible Mn‐Doped Na0.5Bi0.5TiO3‐BaTiO3‐BiFeO3 Film Capacitor with an Ultrahigh Energy Storage Performance

As the rapid development of intelligent systems moves toward flexible electronics, capacitors with extraordinary flexibility and an outstanding energy storage performance will open up broad prospects for powering portable/wearable electronics and pulsed power applications. This work presents a simple one‐step process to fabricate a flexible Mn‐doped 0.97(0.93Na_0.5Bi_0.5TiO₃‐0.07BaTiO₃)‐0.03BiFeO₃ (Mn:NBT‐BT‐BFO) inorganic thin film capacitor with the assistance of a 2D fluorophlogopite mica substrate. The film element, which has a high breakdown strength, great relaxor dispersion, and the coexistence of ferroelectric and antiferroelectric phases, has a high recoverable energy storage density (W_rec ≈81.9 J cm^?3), high efficiency (η ≈64.4%), superior frequency stability (500 Hz–20 kHz), excellent antifatigue property (1 × 10⁹ cycles), and a broad operating temperature window (25–200 °C). The all‐inorganic Mn:NBT‐BT‐BFO/Pt/mica capacitor has a prominent mechanical‐bending resistance without obvious deterioration in its corresponding energy storage capability when it is subjected to a bending radius of 2 mm or repeated bending for 10³ cycles. This work is the first demonstration of an all‐inorganic flexible film capacitor and sheds light on dielectric energy storage devices for portable/wearable applications.     

Roll‐to‐Roll Printed Large‐Area All‐Polymer Solar Cells with 5% Efficiency Based on a Low Crystallinity Conjugated Polymer Blend

The challenge of continuous printing in high‐efficiency large‐area organic solar cells is a key limiting factor for their widespread adoption. A materials design concept for achieving large‐area, solution‐coated all‐polymer bulk heterojunction solar cells with stable phase separation morphology between the donor and acceptor is presented. The key concept lies in inhibiting strong crystallization of donor and acceptor polymers, thus forming intermixed, low crystallinity, and mostly amorphous blends. Based on experiments using donors and acceptors with different degree of crystallinity, the results show that microphase separated donor and acceptor domain sizes are inversely proportional to the crystallinity of the conjugated polymers. This methodology of using low crystallinity donors and acceptors has the added benefit of forming a consistent and robust morphology that is insensitive to different processing conditions, allowing one to easily scale up the printing process from a small‐scale solution shearing coater to a large‐scale continuous roll‐to‐roll (R2R) printer. Large‐area all‐polymer solar cells are continuously roll‐to‐roll slot die printed with power conversion efficiencies of 5%, with combined cell area up to 10 cm². This is among the highest efficiencies realized with R2R‐coated active layer organic materials on flexible substrate.     

Highly Defective Layered Double Perovskite Oxide for Efficient Energy Storage via Reversible Pseudocapacitive Oxygen‐Anion Intercalation

The use of perovskite materials as anion‐based intercalation pseudocapacitor electrodes has received significant attention in recent years. Notably, these materials, characterized by high oxygen vacancy concentrations, do not require high surface areas to achieve a high energy storage capacity as a result of the bulk intercalation mechanism. This study reports that reduced PrBaMn₂O_6–δ (r‐PBM), possessing a layered double perovskite structure, exhibits ultrahigh capacitance and functions as an excellent oxygen anion‐intercalation‐type electrode material for supercapacitors. Formation of the layered double perovskite structure, as facilitated by hydrogen treatment, is shown to significantly enhance the capacitance, with the resulting r‐PBM material demonstrating a very high gravimetric capacitance of 1034.8 F g^?1 and an excellent volumetric capacitance of ≈2535.3 F cm^?3 at a current density of 1 A g^?1. The resultant formation of a double perovskite crystal oxide with a specific layered structure leads to the r‐PBM with a substantially higher oxygen diffusion rate and oxygen vacancy concentration. These superior characteristics show immense promise for their application as oxygen anion‐intercalation‐type electrodes in pseudocapacitors.     

Tuning Nanofillers in In Situ Prepared Polyimide Nanocomposites for High‐Temperature Capacitive Energy Storage

Modern electronics and electrical systems demand efficient operation of dielectric polymer‐based capacitors at high electric fields and elevated temperatures. Here, polyimide (PI) dielectric composites prepared from in situ polymerization in the presence of inorganic nanofillers are reported. The systematic manipulation of the dielectric constant and bandgap of the inorganic fillers, including Al₂O₃, HfO₂, TiO₂, and boron nitride nanosheets, reveals the dominant role of the bandgap of the fillers in determining and improving the high‐temperature capacitive performance of the polymer composites, which is very different from the design principle of the dielectric polymer composites operating at ambient temperature. The Al₂O₃‐ and HfO₂‐based PI composites with concomitantly large bandgap and moderate dielectric constants exhibit substantial improvement in the breakdown strength, discharged energy density, and charge–discharge efficiency when compared to the state‐of‐the‐art dielectric polymers. The work provides a design paradigm for high‐performance dielectric polymer nanocomposites for electrical energy storage at elevated temperatures.     

High‐Performance Relaxor Ferroelectric Materials for Energy Storage Applications

Relaxor ferroelectrics usually possess low remnant polarizations and slim hystereses, which can provide high saturated polarizations and superior energy conversion efficiencies, thus receiving increasing interest as energy storage materials with high discharge energy densities and fast discharge ability. In this study, a relaxor ferroelectric multilayer energy storage ceramic capacitor (MLESCC) based on 0.87BaTiO₃‐0.13Bi(Zn_2/3(Nb_0.85Ta_0.15)_1/3)O₃ (BT‐BZNT) with inexpensive Ag/Pd inner electrodes is prepared by the tape casting method. The MLESCC with two dielectric layers (layer thicknesses of 5 µm) sintered by a two‐step sintering method exhibits excellent energy storage properties with a record‐high discharge energy density of 10.12 J cm^?3, a high energy efficiency of 89.4% achieved at an electric field of 104.7 MV m^?1, a high temperature stability of the energy storage density (with minimal variation of <±5%), and energy efficiency (>90%) over a range of ?75 to 150 °C at 40 MV m^?1. These results suggest that the BT‐BZNT relaxor ferroelectric ceramic material can provide realistic solutions for high‐power energy storage capacitors.     

2D Materials for Large‐Area Flexible Thermoelectric Devices

The rapid development of the concept of the “Internet of Things (IoT)” requires wearable devices with maintenance‐free batteries, and thermoelectric energy conversion based on large‐area flexible materials has attracted much attention. Among large‐area flexible materials, 2D materials, such as graphene and related materials, are promising for thermoelectric applications due to their excellent transport properties and large power factors. In this Review, both single‐crystalline and polycrystalline 2D materials are surveyed using the experimental reports on thermoelectric devices of graphene, black phosphorus, transition metal dichalcogenides, and other 2D materials. In particular, their carrier‐density dependent thermoelectric properties and power factors maximized by Fermi level tuning techniques are focused. The comparison of the relevant performances between 2D materials and commonly used thermoelectric materials reveals the significantly enhanced power factors in 2D materials. Moreover, the current progress in thermoelectric module applications using large‐area 2D material thin films is summarized, which consequently offers great potential for the use of 2D materials in large‐area flexible thermoelectric device applications. Finally, important remaining issues and future perspectives, such as preparation methods, thermal transports, device designs, and promising effects in 2D materials, are discussed.     

Low‐Cost N,N′‐Bicarbazole‐Based Dopant‐Free Hole‐Transporting Materials for Large‐Area Perovskite Solar Cells

Despite the recent unprecedented development of efficient dopant‐free hole transporting materials (HTMs) for high‐performance perovskite solar cells (PSCs) on small‐area devices (≤0.1 cm²), low‐cost dopant‐free HTMs for large‐area PSCs (≥1 cm²) with high power conversion efficiencies (PCEs) have rarely been reported. Herein, two novel HTMs, 3,3′,6,6′ (or 2,2′,7,7′)‐tetrakis(N,N′‐di‐p‐methoxyphenylamine)‐N,N′‐bicarbazole (3,6 BCz‐OMeTAD or 2,7 BCz‐OMeTAD), are synthesized via an extremely simple route from very cheap raw materials. Owing to their excellent film‐forming abilities and matching energy levels, 3,6 BCz‐OMeTAD and 2,7 BCz‐OMeTAD can be successfully employed as a perfect ultrathin (≈30 nm) hole transporting layer in large‐area PSCs up to 1 cm². The 3,6 BCz‐OMeTAD and 2,7 BCz‐OMeTAD based large‐area PSCs show highest PCEs up to 17.0% and 17.6%, respectively. More importantly, high performance large‐area PSCs based on 2,7 BCz‐OMeTAD retain 90% of the initial efficiency after 2000 h storage in an ambient environment without encapsulation.     

High‐Energy Density Li‐Ion Capacitor with Layered SnS2/Reduced Graphene Oxide Anode and BCN Nanosheet Cathode

Lithium‐ion capacitors (LICs) with capacitor‐type cathodes and battery‐type anodes are considered a promising next‐generation advanced energy storages system that meet the requirements of high energy density and power density. However, the mismatch of charge‐storage capacity and electrode kinetics between positive and negative electrodes remains a challenge. Herein, layered SnS₂/reduced graphene oxide (RGO) nanocomposites are developed for negative electrodes and a 2D B/N codoped carbon (BCN) nanosheet is designed for the positive electrode. The SnS₂/RGO derived from SnS₂‐bonded RGO of high conductivity exhibits a capacity of 1198 mA h g^?1 at 100 mA g^?1. Boron and nitrogen atoms in BCN are found to promote adsorption of anions, which enhance the pseudocapacitive contribution as well as expanding the voltage of LICs. A quantitative kinetics analysis indicates that the SnS₂/RGO electrodes with a dominating capacitive mechanism and a diminished intercalation process, benefit the kinetic balance between the two electrodes. With this particular structure, the LIC is able to operate at the highest operating voltage for these devices recorded to date (4.5 V), exhibiting an energy density of 149.5 W h kg^?1, a power density of 35 kW kg^?1, and a capacity retention ratio of 90% after 10 000 cycles.     

Exploring Advanced Sandwiched Arrays by Vertical Graphene and N‐Doped Carbon for Enhanced Sodium Storage

Smart hybridization of active materials into tailored electrode structure is highly important for developing advanced electrochemical energy storage devices. With the help of sandwiched design, herein a powerful strategy is developed to fabricate three‐layer sandwiched composite core/shell arrays via combined hydrothermal and polymerization approaches. In such a unique architecture, wrinkled MoSe₂ nanosheets are sandwiched by vertical graphene (VG) core and N‐doped carbon (N‐C) shell forming sandwiched core/shell arrays. Interesting advantages including high electrical conductivity, strong mechanical stability, and large porosity are combined in the self‐supported VG/MoSe₂/N‐C sandwiched arrays. As a preliminary test, the sodium ion storage properties of VG/MoSe₂/N‐C sandwiched arrays are characterized and demonstrated with high capacity (540 mA h g^?1), enhanced high rate capability, and long‐term cycling stability (298 mA h g^?1 at 2.0 A g^?1 after 1000 cycles). The sandwiched core/shell structure plays positive roles in the enhancement of electrochemical performances due to dual conductive carbon networks, good volume accommodation, and highly porous structure with fast ion diffusion. The directional electrode design protocol provides a general method for synthesis of high‐performance ternary core/shell electrodes.     

Making Ends Meet: Flow Synthesis as the Answer to Reproducible High‐Performance Conjugated Polymers on the Scale that Roll‐to‐Roll Processing Demands

Continuous flow methods are employed for the controlled polymerization of the roll‐to‐roll (R2R) compatible polymer PBDTTTz‐4 including optimization and upscaling experiments. The polymerization rate and materials’ quality can be increased significantly with the continuous flow method where reaction times down to 10 min afforded PBDTTTz‐4 with high molecular weight and a constant quality. The flow method enables full control of the molecular weight via tuning of the flow speed, catalyst loading, and temperature and avoids variation in materials’ quality associated with conventional batch synthesis. Upscaling from 300 mg batch synthesis to 10 g flow synthesis affords PBDTTTz‐4 with a production rate of up to 120 g day^?1 for a very simple in‐house build flow reactor. An average power conversion efficiency (PCE) of 3.5% is achieved on a small scale (1 cm²) and an average PCE of 3.3% is achieved on a large scale (29 cm²). This shows that small device efficiencies can be scaled when using full R2R processing of flexible and encapsulated carbon‐based modules without the use of vacuum, indium‐tin‐oxide, or silver, with the best achieving a PCE of 3.8% PCE.     

High‐Performance Large‐Area Organic Solar Cells Enabled by Sequential Bilayer Processing via Nonhalogenated Solvents

While the performance of laboratory‐scale organic solar cells (OSCs) continues to grow over 13%, the development of high‐efficiency large area OSCs still lags. One big challenge is that the formation of bulk heterojunction morphology is an extremely complicated process and the formed morphology is also a highly delicate balance involving many parameters such as domain size, purity, miscibility, etc. The morphology control becomes much more challenging when the device area is scaled up. In this work, a highly efficient (12.9%) nonfullerene organic solar cell processed using a sequential bilayer deposition method from nonhalogenated solvents, is reported. Using this bilayer processing method, the organic solar cells can be scaled up to a larger area (1 cm²) while maintaining a high performance of 11.4% using doctor‐blade‐coating technique. Moreover, as the acceptor is hidden behind the polymer donor, the possibility of degradation by sunlight is lessened. Thus, improved photostability is observed in the bilayer structure device when compared with the bulk heterojunction device. This method offers a truly compatible processing technique for printing large‐area OSC modules.     

A Stable Vanadium Redox‐Flow Battery with High Energy Density for Large‐Scale Energy Storage

The all‐vanadium redox flow battery is a promising technology for large‐scale renewable and grid energy storage, but is limited by the low energy density and poor stability of the vanadium electrolyte solutions. A new vanadium redox flow battery with a significant improvement over the current technology is reported in this paper. This battery uses sulfate‐chloride mixed electrolytes, which are capable of dissolving 2.5 M vanadium, representing about a 70% increase in energy capacity over the current sulfate system. More importantly, the new electrolyte remains stable over a wide temperature range of ?5 to 50 °C, potentially eliminating the need for electrolyte temperature control in practical applications. This development would lead to a significant reduction in the cost of energy storage, thus accelerating its market penetration.     

Bottom‐Up Confined Synthesis of Nanorod‐in‐Nanotube Structured Sb@N‐C for Durable Lithium and Sodium Storage

Antimony (Sb) has emerged as an attractive anode material for both lithium and sodium ion batteries due to its high theoretical capacity of 660 mA h g^?1. In this work, a novel peapod‐like N‐doped carbon hollow nanotube encapsulated Sb nanorod composite, the so‐called nanorod‐in‐nanotube structured Sb@N‐C, via a bottom‐up confinement approach is designed and fabricated. The N‐doped‐carbon coating and thermal‐reduction process is monitored by in situ high‐temperature X‐ray diffraction characterization. Due to its advanced structural merits, such as sufficient N‐doping, 1D conductive carbon coating, and substantial inner void space, the Sb@N‐C demonstrates superior lithium/sodium storage performance. For lithium storage, the Sb@N‐C exhibits a high reversible capacity (650.8 mA h g^?1 at 0.2 A g^?1), excellent long‐term cycling stability (a capacity decay of only 0.022% per cycle for 3000 cycles at 2 A g^?1), and ultrahigh rate capability (343.3 mA h g^?1 at 20 A g^?1). For sodium storage, the Sb@N‐C nanocomposite displays the best long‐term cycle performance among the reported Sb‐based anode materials (a capacity of 345.6 mA h g^?1 after 3000 cycles at 2 A g^?1) and an impressive rate capability of up to 10 A g^?1. The results demonstrate that the Sb@N‐C nanocomposite is a promising anode material for high‐performance lithium/sodium storage.