Selective Dye Loading at the Heterojunction in Polymer/Fullerene Solar Cells

Selective dye loading at the polymer/fullerene interface was studied for ternary blend bulk heterojunction solar cells, consisting of regioregular poly(3‐hexylthiophene) (RR‐P3HT), a fullerene derivative (PCBM), and a silicon phthalocyanine derivative (SiPc) as a light‐harvesting dye. The photocurrent density and power conversion efficiency of the ternary blend solar cells were most improved by loading SiPc with a content of 4.8 wt%. The absorption and surface energy measurements suggested that SiPc is located in the disordered P3HT domains at the RR‐P3HT/PCBM interface rather than in the PCBM and crystal P3HT domains. From the peak wavelength of SiPc absorption, the local concentration of SiPc ([SiPc]_Local) was estimated for the RR‐P3HT:PCBM:SiPc ternary blends. Even for amorphous films of regiorandom P3HT (RRa‐P3HT) blended with PCBM and SiPc, [SiPc]_Local was higher than the original content, suggesting dye segregation into the RRa‐P3HT/PCBM interface. For RR‐P3HT:PCBM:SiPc blends, [SiPc]_Local increased with the increase in the P3HT crystallinity. Such interfacial segregation of dye molecules in ternary blend films can be rationally explained in terms of the surface energy of each component and the crystallization of P3HT being enhanced by annealing. Notably, the solvent annealing effectively segregated dye molecules into the interface without the formation of PCBM clusters.     

Spontaneous Charge Transfer and Dipole Formation at the Interface Between P3HT and PCBM

In the pursuit of developing new materials for more efficient bulk‐heterojunction solar cells, the blend poly (3‐hexylthiophene):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) serves as an important model system. The success of the P3HT:PCBM blend comes from efficient charge generation and transport with low recombination. There is not, however, a good microscopic picture of what causes these, hindering the development of new material systems. In this report UV photoelectron spectroscopy measurements on both regiorandom‐ (rra) and regioregular‐ (rr) P3HT are presented, and the results are interpreted using the Integer Charge Transfer model. The results suggest that spontaneous charge transfer from P3HT to PCBM occurs after heat treatment of P3HT:PCBM blends. The resulting formation of an interfacial dipole creates an extra barrier at the interface explaining the reduced (non‐)geminate recombination with increased charge generation in heat treated rr‐P3HT:PCBM blends. Extensive photoinduced absorption measurements using both above‐ and below‐bandgap excitation light are presented, in good agreement with the suggested dipole formation.     

The Crucial Influence of Fullerene Phases on Photogeneration in Organic Bulk Heterojunction Solar Cells

The conjugated polymer, poly(2,5‐bis(3‐hexadecylthiophen‐2‐yl)thieno[3,2‐b]thiophene) (pBTTT‐C₁₆), allows a systematic tuning of the blend morphology by varying the acceptor type and fraction, making it a well‐suited structural model for studying the fundamental processes in organic bulk heterojunction solar cells. To analyze the role of intercalated and pure fullerene domains on charge carrier photogeneration, time delayed collection field (TDCF) measurements and Fourier‐transform photocurrent spectroscopy (FTPS) are performed on pBTTT‐C₁₆:[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) solar cells with various stoichiometries. A weak influence of excess photon energy on photogeneration along with a photogeneration having a weaker field dependence at increasing fullerene loading is found. The findings are assigned to a dissociation via thermalized charge transfer (CT) states supported by an enhanced electron delocalization along spatially extended PC₆₁BM nanophases that form in addition to a bimolecular crystal (BMC) for PC₆₁BM rich blends. The highly efficient transfer of charge carriers from the BMC into the pure domains are studied further by TDCF measurements performed on non‐intercalated pBTTT‐C₁₆:bisPC₆₁BM blends. They reveal a field dependent charge generation similar to the 1:4 PC₆₁BM blend, demonstrating that the presence of pure acceptor phases is the major driving force for an efficient, field independent CT dissociation.     

Understanding the Reduced Efficiencies of Organic Solar Cells Employing Fullerene Multiadducts as Acceptors

The use of fullerenes with two or more adducts as acceptors has been recently shown to enhance the performance of bulk‐heterojunction solar cells using poly(3‐hexylthiophene) (P3HT) as the donor. The enhancement is caused by a substantial increase in the open‐circuit voltage due to a rise in the fullerene lowest unoccupied molecular orbital (LUMO) level when going from monoadducts to multiadducts. While the increase in the open‐circuit voltage is obtained with many different polymers, most polymers other than P3HT show a substantially reduced photocurrent when blended with fullerene multiadducts like bis‐PCBM (bis adduct of Phenyl‐C₆₁‐butyric acid methyl ester) or the indene C₆₀ bis‐adduct ICBA. Here we investigate the reasons for this decrease in photocurrent. We find that it can be attributed partly to a loss in charge generation efficiency that may be related to the LUMO‐LUMO and HOMO‐HOMO (highest occupied molecular orbital) offsets at the donor‐acceptor heterojunction, and partly to reduced charge carrier collection efficiencies. We show that the P3HT exhibits efficient collection due to high hole and electron mobilities with mono‐ and multiadduct fullerenes. In contrast the less crystalline polymer Poly[[9‐(1‐octylnonyl)‐9H‐carbazole‐2,7‐diyl]‐2,5‐thiophenediyl‐2,1,3‐benzothiadiazole‐4,7‐diyl‐2,5‐thiophenediyl (PCDTBT) shows inefficient charge carrier collection, assigned to low hole mobility in the polymer and low electron mobility when blended with multiadduct fullerenes.     

The Role of Exciton Ionization Processes in Bulk Heterojunction Organic Photovoltaic Cells

To realize efficient photoconversion in organic semiconductors, photogenerated excitons must be dissociated into their constituent electronic charges. In an organic photovoltaic (OPV) cell, this is most often accomplished using an electron donor–acceptor (D–A) interface. Interestingly, recent work on MoO_x/C₆₀ Schottky OPVs has demonstrated that excitons in C₆₀ may also undergo efficient bulk‐ionization and generate photocurrent as a result of the large built‐in field created by the MoO_x/C₆₀ interface. Here, it is demonstrated that bulk ionization processes also contribute to the short‐circuit current density (J_SC) and open‐circuit voltage (V_OC) in bulk heterojunction (BHJ) OPVs with fullerene‐rich compositions. Temperature‐dependent measurements of device performance are used to distinguish dissociation by bulk‐ionization from charge transfer at the D–A interface. In optimized fullerene‐rich BHJs based on the D–A pairing of boron subphthalocyanine chloride (SubPc)–C₆₀, bulk‐ionization is found to be responsible for ≈16% of the total photocurrent, and >30% of the photocurrent originating from C₆₀. The presence of bulk‐ionization in C₆₀ also impacts the temperature dependence of V_OC, with fullerene‐rich SubPc:C₆₀ BHJ OPVs showing a larger V_OC than evenly mixed BHJs. The prevalence of bulk‐ionization processes in efficient, fullerene‐rich BHJs underscores the need to include these effects when engineering device design and morphology in OPVs.     

Plasmonic Back Reflectors: A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

The Role of Photon Energy in Free Charge Generation in Bulk Heterojunction Solar Cells

To determine the role of photon energy on charge generation in bulk heterojunction solar cells, the bias voltage dependence of photocurrent for excitation with photon energies below and above the optical band gap is investigated in two structurally related polymer solar cells. Charges generated in (poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′′]dithiophene)‐alt‐4,7‐(2,1,3‐benzothia­diazole)] (C‐PCPDTBT):[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) solar cells via excitation of the low‐energy charge transfer (CT) state, situated below the optical band gap, need more voltage to be extracted than charges generated with excitation above the optical band gap. This indicates a lower effective binding energy of the photogenerated electrons and holes when the excitation is above the optical band gap than when excitation is to the bottom of the CT state. In blends of PCBM with the silicon‐analogue, poly[(4,4‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(2,1,3‐benzothiadiazole)‐4,7‐diyl] (Si‐PCPDTBT), there is no effect of the photon energy on the electric field dependence of the dissociation efficiency of the CT state. C‐PCPDTBT and Si‐PCPDTBT have very similar electronic properties, but their blends with PCBM differ in the nanoscale phase separation. The morphology is coarser and more crystalline in Si‐PCPDTBT:PCBM blends. The results demonstrate that the nanomorphological properties of the bulk heterojunction are important for determining the effective binding energy in the generation of free charges at the heterojunction.     

Intra‐Molecular Donor–Acceptor Interaction Effects on Charge Dissociation,Charge Transport,and Charge Collection in Bulk‐Heterojunction Organic Solar Cells

This article reports experimental studies on internal charge dissociation, transport, and collection by using magnetic field effects of photocurrent (MFE_PC) and light‐assisted dielectric response (LADR) in highly‐efficient organic solar cells based on photovoltaic polymer PTB2 and PTB4 with intra‐molecular “donor–acceptor” interaction. The MFE_PC at low‐field (< 150 mT) indicates that intra‐molecular “donor‐acceptor” interaction generates charge dissociation in un‐doped PTB2 and PTB4 films, which is similar to that in lightly doped P3HT (Poly(3‐hexylthiophene)) with 5 wt% PCBM (1‐(3‐methyloxycarbonyl)‐propyl‐1‐phenyl (6,6) C₆₁). After PTB2 and PTB4 are mixed with PCBM to form bulk‐heterojunctions, the MFE_PC at high‐field (> 150 mT) reveals that the charge‐transfer complexes formed at PTB2:PCBM and PTB4:PCBM interfaces have much lower binding energies due to stronger electron‐withdrawing abilities, as compared to the P3HT:PCBM device, towards the generation of photocurrent. Furthermore, the light‐assisted dielectric response: LADR indicates that the PTB2:PCBM and PTB4:PCBM solar cells exhibit larger capacitances relative to P3HT:PCBM device under photoexcitation. This reflects that the PTB2:PCBM and PTB4:PCBM bulk heterojunctions have more effective charge transport and collection than the P3HT:PCBM counterpart. As a result, our experimental results indicate that intra‐molecular “donor‐acceptor” interaction plays an important role to enhance charge dissociation, transport, and collection in bulk‐heterojunction organic solar cells.     

Comparison of the Morphology Development of Polymer–Fullerene and Polymer–Polymer Solar Cells during Solution‐Shearing Blade Coating

In this work, the detailed morphology studies of polymer poly(3‐hexylthiophene‐2,5‐diyl) (P3HT):fullerene(PCBM) and polymer(P3HT):polymer naphthalene diimide thiophene (PNDIT) solar cell are presented to understand the challenge for getting high performance all‐polymer solar cells. The in situ X‐ray scattering and optical interferometry and ex situ hard and soft X‐ray scattering and imaging techniques are used to characterize the bulk heterojunction (BHJ) ink during drying and in dried state. The crystallization of P3HT polymers in P3HT:PCBM bulk heterojunction shows very different behavior compared to that of P3HT:PNDIT BHJ due to different mobilities of P3HT in the donor:acceptor glass. Supplemented by the ex situ grazing incidence X‐ray diffraction and soft X‐ray scattering, PNDIT has a lower tendency to form a mixed phase with P3HT than PCBM, which may be the key to inhibit the donor polymer crystallization process, thus creating preferred small phase separation between the donor and acceptor polymer.     

Controlling Hierarchy in Solution‐processed Polymer Solar Cells Based on Crosslinked P3HT

Understanding and controlling the morphology of donor/acceptor blends is critical for the development of solution processable organic solar cells. By crosslinking a poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) film we have been able to spin‐coat [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) onto the film to form a structure that is close to a bilayer, thus creating an ideal platform for investigating interdiffusion in this model system. Neutron reflectometry (NR) demonstrates that without any thermal treatment a smaller amount of PCBM percolates throughout the crosslinked P3HT when compared to a non‐crosslinked P3HT film. Using time‐resolved NR we also show thermal annealing increases the rate of diffusion, resulting in a near‐uniform distribution of PCBM throughout the polymer film. XPS measurements confirm the presence of both P3HT and PCBM at the annealed film's surface indicating that the two components are intermixed. Photovoltaic devices fabricated using this bilayer approach and suitable annealing conditions yielded comparable power conversion efficiencies to bulk heterojunction devices made from the same materials. The crosslinking procedure has also enabled the formation of patterned P3HT films by photolithography. Pillars with feature sizes down to 2 μm were produced and after subsequent deposition of PCBM and thermal annealing devices with efficiencies of up to 1.4% were produced.     

Non‐Fullerene Acceptor‐Based Bulk Heterojunction Polymer Solar Cells: Engineering the Nanomorphology via Processing Additives

The performance of bulk heterojunction solar cells made from blends of a non‐fullerene acceptor, N,N′‐bis(2‐ethylhexyl)‐2,6‐bis(5″‐hexyl‐[2,2′;5′,2″]terthiophen‐5yl)‐1,4,5,8‐naphthalene diimide (NDI‐3TH), and poly(3‐hexylthiophene) (P3HT) donor is enhanced 10‐fold by using a processing additive in conjunction with an electron‐blocking and a hole‐blocking buffer layers. The power conversion efficiency of P3HT:NDI‐3TH solar cells improves from 0.14% to 1.5% by using a processing additive (1,8‐diiodooctane) at an optimum concentration of 0.2 vol%, which is far below the 2‐3 vol% optimum concentrations found in polymer/fullerene systems. TEM and AFM imaging show that the size and connectivity of the NDI‐3TH domains in the phase‐separated P3HT:NDI‐3TH blends vary strongly with the concentration of the processing additive. These results demonstrate, for the first time, that processing additives can be effective in the optimization of the morphology and performance of bulk heterojunction polymer solar cells based on non‐fullerene acceptors.     

Plastic Solar Cells: Interdiffusion of PCBM and P3HT Reveals Miscibility in a Photovoltaically Active Blend (Adv. Energy Mater. 1/2011)

Developing a better understanding of the evolution of morphology in plastic solar cells is the key to designing new materials and structures that achieve photoconversion efficiencies greater than 10%. In the most extensively characterized system, the poly(3‐hexyl thiophene) (P3HT):[6,6]‐phenyl‐C₆₁‐butyric‐acid‐methyl‐ester (PCBM) bulk heterojunction, the origins and evolution of the blend morphology during processes such as thermal annealing are not well understood. In this work, we use a model system, a bilayer of P3HT and PCBM, to develop a more complete understanding of the miscibility and diffusion of PCBM within P3HT during thermal annealing. We find that PCBM aggregates and/or molecular species are miscible and mobile in disordered P3HT, without disrupting the ordered lamellar stacking of P3HT chains. The fast diffusion of PCBM into the amorphous regions of P3HT suggests the favorability of mixing in this system, opposing the belief that phase‐pure domains form in BHJs due to immiscibility of these two components.     

Interdiffusion of PCBM and P3HT Reveals Miscibility in a Photovoltaically Active Blend

Developing a better understanding of the evolution of morphology in plastic solar cells is the key to designing new materials and structures that achieve photoconversion efficiencies greater than 10%. In the most extensively characterized system, the poly(3‐hexyl thiophene) (P3HT):[6,6]‐phenyl‐C₆₁‐butyric‐acid‐methyl‐ester (PCBM) bulk heterojunction, the origins and evolution of the blend morphology during processes such as thermal annealing are not well understood. In this work, we use a model system, a bilayer of P3HT and PCBM, to develop a more complete understanding of the miscibility and diffusion of PCBM within P3HT during thermal annealing. We find that PCBM aggregates and/or molecular species are miscible and mobile in disordered P3HT, without disrupting the ordered lamellar stacking of P3HT chains. The fast diffusion of PCBM into the amorphous regions of P3HT suggests the favorability of mixing in this system, opposing the belief that phase‐pure domains form in BHJs due to immiscibility of these two components.     

Simultaneous Open‐Circuit Voltage Enhancement and Short‐Circuit Current Loss in Polymer: Fullerene Solar Cells Correlated by Reduced Quantum Efficiency for Photoinduced Electron Transfer

The limits of maximizing the open‐circuit voltage V_oc in solar cells based on poly[2,7‐(9,9‐didecylfluorene)‐alt‐5,5‐(4,7‐di‐2‐thienyl‐2,1,3‐benzothiadiazole)] (PF10TBT) as a donor using different fullerene derivatives as acceptor are investigated. Bulk heterojunction solar cells with PF10TBT and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) give a V_oc over 1 V and a power conversion efficiency of 4.2%. Devices in which PF10TBT is blended with fullerene bisadduct derivatives give an even higher V_oc, but also a strong decrease in short circuit current (J_sc). The higher V_oc is attributed to the higher LUMO of the acceptors in comparison to PCBM. By investigating the photophysics of PF10TBT:fullerene blends using near‐IR photo‐ and electroluminescence, time‐resolved photoluminescence, and photoinduced absorption we find that the charge transfer (CT) state is not formed efficiently when using fullerene bisadducts. Hence, engineering acceptor materials with a LUMO level that is as high as possible can increase V_oc, but will only provide a higher power conversion efficiency, when the quantum efficiency for charge transfer is preserved. To quantify this, we determine the CT energy (E_CT) and optical band gap (E_g), defined as the lowest first singlet state energy E_S1 of either the donor or acceptor, for each of the blends and find a clear correlation between the free energy for photoinduced electron transfer and J_sc. We find that E_g ? qV_oc > 0.6 eV is a simple, but general criterion for efficient charge generation in donor‐acceptor blends.     

Sequential Processing for Organic Photovoltaics: Design Rules for Morphology Control by Tailored Semi‐Orthogonal Solvent Blends

Design rules are presented for significantly expanding sequential processing (SqP) into previously inaccessible polymer:fullerene systems by tailoring binary solvent blends for fullerene deposition. Starting with a base solvent that has high fullerene solubility, 2‐chlorophenol (2‐CP), ellipsometry‐based swelling experiments are used to investigate different co‐solvents for the fullerene‐casting solution. By tuning the Flory‐Huggins χ parameter of the 2‐CP/co‐solvent blend, it is possible to optimally swell the polymer of interest for fullerene interdiffusion without dissolution of the polymer underlayer. In this way solar cell power conversion efficiencies are obtained for the PTB7 (poly[(4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)(3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl)]) and PC₆₁BM (phenyl‐C₆₁‐butyric acid methyl ester) materials combination that match those of blend‐cast films. Both semicrystalline (e.g., P3HT (poly(3‐hexylthiophene‐2,5‐diyl)) and entirely amorphous (e.g., PSDTTT (poly[(4,8‐di(2‐butyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)‐alt‐(2,5‐bis(4,4′‐bis(2‐octyl)dithieno[3,2‐b:2′3′‐d]silole‐2,6‐diyl)thiazolo[5,4‐d]thiazole)]) conjugated polymers can be processed into highly efficient photovoltaic devices using the solvent‐blend SqP design rules. Grazing‐incidence wide‐angle x‐ray diffraction experiments confirm that proper choice of the fullerene casting co‐solvent yields well‐ordered interdispersed bulk heterojunction (BHJ) morphologies without the need for subsequent thermal annealing or the use of trace solvent additives (e.g., diiodooctane). The results open SqP to polymer/fullerene systems that are currently incompatible with traditional methods of device fabrication, and make BHJ morphology control a more tractable problem.     

Decreased Recombination Through the Use of a Non‐Fullerene Acceptor in a 6.4% Efficient Organic Planar Heterojunction Solar Cell

An optimization of several aspects of planar heterojunction solar cells based on boron subnaphthalocyanine chloride (SubNc) as a donor material is presented. The use of hexachlorinated boron subphthalocyanine chloride (Cl₆SubPc) as an alternative acceptor to C₆₀ allows for the simultaneous increase of the short‐circuit current, fill factor, and open‐circuit voltage compared to cells with fullerene acceptors. This is due to the complementary absorption of Cl₆SubPc versus SubNc, reduced recombination at the heterointerface, and improved energetic alignment. Furthermore, insertion of a thin diindeno[1,2,3‐cd:1′,2′,3′‐lm]perylene (DIP) layer at the anode results in a very significant 60% increase in photocurrent owing to reduced exciton quenching at the anode. The simultaneous improvement of all three solar cell para­meters results in a power conversion efficiency of 6.4% for a non‐fullerene planar heterojunction cell.     

Electron Collection as a Limit to Polymer:PCBM Solar Cell Efficiency: Effect of Blend Microstructure on Carrier Mobility and Device Performance in PTB7:PCBM

The poor photovoltaic performance of state‐of‐the‐art blends of poly[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl] (PTB7) and [6,6]‐phenyl‐C61‐butyric acid (PCBM) at large active layer thicknesses is studied using space‐charge‐limited current mobility and photovoltaic device measurements. The poor performance is found to result from relatively low electron mobility. This is attributed to the low tendency of PTB7 to aggregate, which reduces the ability of the fullerene to form a connected network. Increasing the PCBM content 60–80 wt% increases electron mobility and accordingly improves performance for thicker devices, resulting in a fill factor (FF) close to 0.6 at 300 nm. The result confirms that by improving only the connectivity of the fullerene phase, efficient electron and hole collection is possible for 300 nm‐thick PTB7:PCBM devices. Furthermore, it is shown that solvent additive 1,8‐diiodooctane (DIO), used in the highest efficiency PTB7:PCBM devices, does not improve the thickness dependence and, accordingly, does not lead to an increase in either hole or electron mobility or in the carrier lifetime. A key challenge for researchers is therefore to develop new methods to ensure connectivity in the fullerene phase in blends without relying on either a large excess of fullerene or strong aggregation of the polymer.     

A Supramolecular “Double‐Cable” Structure with a 12944 Helix in a Columnar Porphyrin‐C60 Dyad and its Application in Polymer Solar Cells

A novel porphyrin‐C₆₀ dyad (PCD1) is designed and synthesized to investigate and manipulate the supramolecular structure where geometrically isotropic [such as [60]fullerene (C₆₀)] and anisotropic [such as porphyrin (Por)] units coexist. It is observed that PCD1 possesses an enantiomeric phase behavior. The melting temperature of the stable PCD1 thermotropic phase is 160 °C with a latent heat (ΔH) of 18.5 kJ mol^?1. The phase formation is majorly driven by the cooperative intermolecular Por–Por and C₆₀–C₆₀ interactions. Structural analysis reveals that this stable phase possesses a supramolecular “double‐cable” structure with one p‐type Por core columnar channel and three helical n‐type C₆₀ peripheral channels. These “double‐cable” columns further pack into a hexagonal lattice with a = b = 4.65 nm, c = 41.3 nm, α = β = 90°, and γ = 120°. The column repeat unit is determined to possess a 129₄₄ helix. With both donor (D; Pro) and acceptor (A; C₆₀) units having their own connecting channels as well as the large D/A interface within the supramolecular “double‐cable” structure, PCD1 has photogenerated carriers with longer lifetimes compared to the conventional electron acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester. A phase‐separated columnar morphology is observed in a bulk‐heterojunction (BHJ) material made by the physical blend of a low band‐gap conjugated polymer, [poly[2,6‐(4,4‐bis‐(2‐ethylhexyl)‐4H‐cyclopenta [2,1‐b;3,4‐b′]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothia‐diazole)] (PCPDTBT), and PCD1. With a specific phase structure in the solid state and in the blend, PCD1 is shown to be a promising candidate as a new electron acceptor in high performance BHJ polymer solar cells.     

Toward High‐Temperature Stability of PTB7‐Based Bulk Heterojunction Solar Cells: Impact of Fullerene Size and Solvent Additive

The use of fullerene as acceptor limits the thermal stability of organic solar cells at high temperatures as their diffusion inside the donor leads to phase separation via Ostwald ripening. Here it is reported that fullerene diffusion is fully suppressed at temperatures up to 140 °C in bulk heterojunctions based on the benzodithiophene‐based polymer (the poly[[4,8‐bis[(2‐ethylhexyl)oxy]‐benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]‐thieno[3,4‐b]thiophenediyl]], (PTB7) in combination with the fullerene derivative [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₀BM). The blend stability is found independently of the presence of diiodooctane (DIO) used to optimize nanostructuration and in contrast to PTB7 blends using the smaller fullerene derivative PC₇₀BM. The unprecedented thermal stability of PTB7:PC₇₀BM layers is addressed to local minima in the mixing enthalpy of the blend forming stable phases that inhibit fullerene diffusion. Importantly, although the nanoscale morphology of DIO processed blends is thermally stable, corresponding devices show strong performance losses under thermal stress. Only by the use of a high temperature annealing step removing residual DIO from the device, remarkably stable high efficiency solar cells with performance losses less than 10% after a continuous annealing at 140 °C over 3 days are obtained. These results pave the way toward high temperature stable polymer solar cells using fullerene acceptors.