Layer‐by‐Layer Solution‐Processed Low‐Bandgap Polymer‐PC61BM Solar Cells with High Efficiency

Polymer solar cells (PSCs) are fabricated without solvent additives using a low‐bandgap polymer, PBDTTT‐C‐T, as the donor and [6,6]‐phenyl‐C61‐butyric‐acid‐methyl‐ester (PC₆₁BM) as the acceptor. Donor‐acceptor blend and layer‐by‐layer (LL) solution process are used to form active layers. Relative to the blend devices, the LL devices exhibit stronger absorption, better vertical phase separation, higher hole and electron mobilities, and better charge extraction at correct electrodes. As a result, after thermal annealing the LL devices exhibit an average power conversion efficiency (PCE) of 6.86%, which is much higher than that of the blend devices (4.31%). The best PCE of the LL devices is 7.13%, which is the highest reported for LL processed PSCs and among the highest reported for PC₆₁BM‐based single‐junction PSCs.     

Delicate Morphology Control Triggers 14.7% Efficiency All‐Small‐Molecule Organic Solar Cells

Morphology is a critical factor to determine the photovoltaic performance of organic solar cells (OSCs). However, delicately fine‐tuning the morphology involving only small molecules is an extremely challenging task. Herein, a simple, generic, and effective concentration‐induced morphology manipulation approach is demonstrated to prompt both the state‐of‐the‐art thin‐film BTR‐Cl:Y6 and thick‐film BTR:PC₇₁BM all‐small‐molecule (ASM) OSCs to a record level. The morphology is delicately controlled by subtly altering the prepared solution concentration but maintaining the identical active layer thickness. The remarkable performance enhancement achieved by this approach mainly results from the enhanced absorption, reduced trap‐assistant recombination, increased crystallinity, and optimized phase‐separated network. These findings demonstrate that a concentration‐induced morphology manipulation strategy can further propel the reported best‐performing ASM OSCs to a brand‐new level, and provide a promising way to delicately control the morphology towards high‐performance ASM OSCs.     

Higher Mobility and Carrier Lifetimes in Solution‐Processable Small‐Molecule Ternary Solar Cells with 11% Efficiency

Solution‐processed small molecule (SM) solar cells have the prospect to outperform their polymer‐fullerene counterparts. Considering that both SM donors/acceptors absorb in visible spectral range, higher expected photocurrents should in principle translate into higher power conversion efficiencies (PCEs). However, limited bulk‐heterojunction (BHJ) charge carrier mobility (<10^‐4 cm² V^‐1 s^‐1) and carrier lifetimes (<1 µs) often impose active layer thickness constraints on BHJ devices (≈100 nm), limiting external quantum efficiencies (EQEs) and photocurrent, and making large‐scale processing techniques particularly challenging. In this report, it is shown that ternary BHJs composed of the SM donor DR3TBDTT (DR3), the SM acceptor ICC6 and the fullerene acceptor PC₇₁BM can be used to achieve SM‐based ternary BHJ solar cells with active layer thicknesses >200 nm and PCEs nearing 11%. The examinations show that these remarkable figures are the result of i) significantly improved electron mobility (8.2 × 10^‐4 cm² V^‐1 s^‐1), ii) longer carrier lifetimes (2.4 µs), and iii) reduced geminate recombination within BHJ active layers to which PC₇₁BM has been added as ternary component. Optically thick (up to ≈500 nm) devices are shown to maintain PCEs >8%, and optimized DR3:ICC6:PC₇₁BM solar cells demonstrate long‐term shelf stability (dark) for >1000 h, in 55% humidity air environment.     

Polymer Solar Cells with Efficiency >10% Enabled via a Facile Solution‐Processed Al‐Doped ZnO Electron Transporting Layer

A facile and low‐temperature (125 °C) solution‐processed Al‐doped ZnO (AZO) buffer layer functioning very effectively as electron accepting/hole blocking layer for a wide range of polymer:fullerene bulk heterojunction systems, yielding power conversion efficiency in excess of 10% (8%) on glass (plastic) substrates is described. The ammonia‐treatment of the aqueous AZO nanoparticle solution produces compact, crystalline, and smooth thin films, which retain the aluminum doping, and eliminates/reduces the native defects by nitrogen incorporation, making them good electron transporters and energetically matched with the fullerene acceptor. It is demonstrated that highly efficient solar cells can be achieved without the need for additional surface chemical modifications of the buffer layer, which is a common requirement for many metal oxide buffer layers to yield efficient solar cells. Also highly efficient solar cells are achieved with thick AZO films (>50 nm), highlighting the suitability of this material for roll‐to‐roll coating. Preliminary results on the applicability of AZO as electron injection layer in F8BT‐based polymer light emitting diode are also presented.     

ITO‐Free and Fully Solution‐Processed Semitransparent Organic Solar Cells with High Fill Factors

Organic photovoltaic (OPV) solar cells that can be simply processed from solution are in the focus of the academic and industrial community because of their enormous potential to reduce cost. One big challenge in developing a fully solution‐processed OPV technology is the design of a well‐performing electrode system, allowing the replacement of ITO. Several solution‐processed electrode systems were already discussed, but none of them could match the performance of ITO. Here, we report efficient ITO‐free and fully solution‐processed semitransparent inverted organic solar cells based on silver nanowire (AgNW) electrodes. To demonstrate the potential of these AgNW electrodes, they were employed as both the bottom and top electrodes. Record devices achieved fill factors as high as 63.0%, which is comparable to ITO based reference devices. These results provide important progress for fully printed organic solar cells and indicate that ITO‐free, transparent as well as non‐transparent organic solar cells can indeed be fully solution‐processed without losses.     

Constructing High‐Performance All‐Small‐Molecule Ternary Solar Cells with the Same Third Component but Different Mechanisms for Fullerene and Non‐fullerene Systems

Two types of all‐small‐molecule ternary solar cells consisting of two small‐molecule donors and one acceptor (fullerene/non‐fullerene) are developed. Interestingly, both these devices have a common component: a carefully designed medium bandgap small molecule, which possesses appropriate energy levels and displays good compatibility with the host donor. In the fullerene system, the charge‐relaying role of the additive donor is confirmed by the improved charge transportation and suppressed charge recombination. While in the non‐fullerene system, the mixed face‐on and edge‐on orientation of the ternary film induced by the additive donor dominates the promotion of charge transportation. Accordingly, both ternary devices deliver higher short‐circuit current density, fill factor, and power conversion efficiencies of over 10% compared to binary ones. This work offers a promising guideline on the construction of high‐performance all‐small‐molecule ternary solar cells by incorporating a miscible small‐molecule donor.     

Mixed Domains Enhance Charge Generation and Extraction in Bulk‐Heterojunction Solar Cells with Small‐Molecule Donors

The interplay between nanomorphology and efficiency of polymer‐fullerene bulk‐heterojunction (BHJ) solar cells has been the subject of intense research, but the generality of these concepts for small‐molecule (SM) BHJs remains unclear. Here, the relation between performance; charge generation, recombination, and extraction dynamics; and nanomorphology achievable with two SM donors benzo[1,2‐b:4,5‐b]dithiophene‐pyrido[3,4‐b]‐pyrazine BDT(PPTh₂)₂, namely SM1 and SM2, differing by their side‐chains, are examined as a function of solution additive composition. The results show that the additive 1,8‐diiodooctane acts as a plasticizer in the blends, increases domain size, and promotes ordering/crystallinity. Surprisingly, the system with high domain purity (SM1) exhibits both poor exciton harvesting and severe charge trapping, alleviated only slightly with increased crystallinity. In contrast, the system consisting of mixed domains and lower crystallinity (SM2) shows both excellent exciton harvesting and low charge recombination losses. Importantly, the onset of large, pure crystallites in the latter (SM2) system reduces efficiency, pointing to possible differences in the ideal morphologies for SM‐based BHJ solar cells compared with polymer‐fullerene devices. In polymer‐based systems, tie chains between pure polymer crystals establish a continuous charge transport network, whereas SM‐based active layers may in some cases require mixed domains that enable both aggregation and charge percolation to the electrodes.     

Efficient and Hysteresis‐Free Perovskite Solar Cells Based on a Solution Processable Polar Fullerene Electron Transport Layer

Fullerene derivatives, which possess extraordinary geometric shapes and high electron affinity, have attracted significant attention for thin film technologies. This study demonstrates an important photovoltaic application using carboxyl‐functionalized carbon buckyballs, C60 pyrrolidine tris‐acid (CPTA), to fabricate electron transport layers (ETLs) that replace traditional metal oxide‐based ETLs in efficient and stable n‐i‐p‐structured planar perovskite solar cells (PSCs). The uniform CPTA film is covalently anchored onto the surface of indium tin oxide (ITO), significantly suppressing hysteresis and enhancing the flexural strength in the CPTA‐modified PSCs. Moreover, solution‐processable CPTA‐based ETLs also enable the fabrication of lightweight flexible PSCs. The maximum‐performing device structures composed of ITO/CPTA/CH₃NH₃PbI₃/2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD)/Au yield power conversion efficiencies of more than 18% on glass substrates and up to 17% on flexible substrates. These results indicate that the CPTA layers provide new opportunities for solution‐processed organic ETLs by substantially simplifying the procedure for fabricating PSCs for portable applications.     

Effects of Solvent Additives on Morphology,Charge Generation,Transport, and Recombination in Solution‐Processed Small‐Molecule Solar Cells

The effects of solvent additive (1,8‐diiodooctane (DIO)) on the morphology, charge generation, transport, and recombination in solution‐processed small‐molecule solar cells are studied and these parameters are correlated with device performance. In the optimum nanoscale morphology, which is processed with 0.4% DIO, the phase separation is large enough to create a percolating pathway for carrier transport, yet still small enough to form large interfacial area for efficient charge separation. Complete phase separation in this film reduces the interfacial defects, which occurs without DIO, and hence suppresses the monomolecular recombination. Moreover, balanced charge transport and weak bimolecular recombination lead to a high fill factor (72%). On the other hand, an excess amount of DIO (0.8%) in the solvent results in the over‐aggregation of the donor phase, which disturbs the percolating pathway of the acceptor phase and reduces the electron mobility. The over‐aggregation of the donor phase also shrinks the interfacial area for charge separation and consequently reduces the photocurrent generation.     

From Binary to Ternary: Improving the External Quantum Efficiency of Small‐Molecule Acceptor‐Based Polymer Solar Cells with a Minute Amount of Fullerene Sensitization

Ternary blend is proved to be a potential contender for achieving high efficiency in organic photovoltaics, which can apparently strengthen the absorption of active layer so as to better harvest light irradiation. Much of the previous work in ternary polymer solar cells focuses on broadening the absorption spectrum; however, a new insight is brought to study the third component, which in tiny amounts influents the small‐molecule acceptor‐based device performance. Without contributing to complementing the absorption, a minute amount of fullerene derivative, Bis‐PC₇₀BM, can effectively play an impressive role as sensitizer in enhancing the external quantum efficiency of the host binary blend, especially for polymeric donor. Detailed investigations reveal that the minute addition of Bis‐PC₇₀BM can realize morphology modification as well as facilitate electron transfer from polymeric donor to small molecule acceptor via cascade energy level modulation, and therefore lead to an improvement in device efficiency.     

Overcoming Interfacial Losses in Solution‐Processed Organic Multi‐Junction Solar Cells

Organic solar cells are promising in terms of full‐solution‐processing which enables low‐cost and large‐scale fabrication. While single‐junction solar cells have seen a boost in power conversion efficiency (PCE), multi‐junction solar cells are promising to further enhance the PCE. In all‐solution‐processed multi‐junction solar cells, interfacial losses are often encountered between hole‐transporting layer (HTL) and the active layers and therefore greatly limit the application of newly developed high‐performance donor and acceptor materials in multi‐junction solar cells. Here, the authors report on a systematic study of interface losses in both single‐junction and multi‐junction solar cells based on representative polymer donors and HTLs using electron spectroscopy and time‐of‐flight secondary ion mass spectrometry. It is found that a facile mixed HTL containing poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and MoO _x nanoparticles successfully overcomes the interfacial losses in both single‐ and multi‐junction solar cells based on various active layers by reducing interface protonation, promoting better energy‐level alignment, and forming a dense and smooth layer. Solution‐processed single‐junction solar cells are demonstrated to reach the same performance as with evaporated MoO _x (over 7%). Multi‐junction solar cells with polymers containing nitrogen atoms as the first layer and the mixed PEDOT:PSS and MoO _x nanoparticles as hole extraction layer reach fill factor (FF) of over 60%, and PCE of over 8%, while the identical stack with pristine PEDOT:PSS or MoO _x nanoparticles show FF smaller than 50% and PCE less than 5%.     

A Cross‐Linked Interconnecting Layer Enabling Reliable and Reproducible Solution‐Processing of Organic Tandem Solar Cells

The performance of tandem organic solar cells (OSCs) is directly related to the functionality and reliability of the interconnecting layer (ICL). However, it is a challenge to develop a fully functional ICL for reliable and reproducible fabrication of solution‐processed tandem OSCs with minimized optical and electrical losses, in particular for being compatible with various state‐of‐the‐art photoactive materials. Although various ICLs have been developed to realize tandem OSCs with impressively high performance, their reliability, reproducibility, and generic applicability are rarely analyzed and reported so far, which restricts the progress and widespread adoption of tandem OSCs. In this work, a robust and fully functional ICL is developed by incorporating a hydrolyzed silane crosslinker, (3‐glycidyloxypropyl)trimethoxysilane (GOPS), into poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), and its functionality for reliable and reproducible fabrication of tandem OSCs based on various photoactive materials is validated. The cross‐linked ICL can successfully protect the bottom active layer against penetration of high boiling point solvents during device fabrication, which widely broadens the solvent selection for processing photoactive materials with high quality and reliability, providing a great opportunity to continuously develop the tandem OSCs towards future large‐scale production and commercialization.     

Comparative Study of Effects of Terminal Non‐Alkyl Aromatic and Alkyl Groups on Small‐Molecule Solar Cell Performance

Small‐molecule donors for solar cells are usually end‐capped with π‐systems or aliphatic chains extending the π‐conjugation of the molecules's backbone. Compared with alkyl terminals, π‐systems can form π?π arrangements, for example, with an aligning spherical fullerene π‐system. To study the effects of two kinds of terminals on the solar cell performance, the non‐alkyl, branched aromatic and electron‐donating diphenylamine (DPA) and the aliphatic n‐butyl (n‐Bu) unit are selected as end‐capping groups on a diketopyrrolo­pyrrole‐based linear backbone, affording two new solution‐processable small‐molecule donors. Photovoltaic data indicate that by changing the end‐function from n‐Bu to DPA, the photocurrent significantly increases from 8.35 to 15.64 mA cm^?2 and the efficiency from 3.2 to 5.8%. Characterization of absorption, morphology, recombination, and carrier transportation clearly demonstrates that the higher photocurrent can be attributed to a higher density of the mobile carriers (i.e., free holes, in this case). The DPA end‐functions enhance the light‐harvesting capacity, improve the charge dissociation, and reduce the recombination loss, all of which lead to more carriers being collected by the electrode. This work demonstrates that the choice of end‐function along the molecular backbone is as important to improve the cell performance as the light‐harvesting backbone and the side‐chains.     

Environmentally Printing Efficient Organic Tandem Solar Cells with High Fill Factors: A Guideline Towards 20% Power Conversion Efficiency

The tandem concept involves stacking two or more cells with complementary absorption spectra in series or parallel connection, harvesting photons at the highest possible potential. It is strongly suggested that the roll‐to‐roll production of organic solar cells will employ the tandem concept to enhance the power conversion efficiency (PCE). However, due to the undeveloped deposition techniques, the challenges in ink formulation as well as the lack of commercially available high performance active materials, roll‐to‐roll fabrication of highly efficient organic tandem solar cells currently presents a major challenge. The reported high PCE values from lab‐scale spin‐coated devices are, of course, representative, but not helpful for commercialization. Here, organic tandem solar cells with exceptionally high fill factors and PCE values of 7.66% (on glass) and 5.56% (on flexible substrate), which are the highest values for the solution‐processed tandem solar cells fabricated by a mass‐production compatible coating technique under ambient conditions, are demonstrated. To predict the highest possible performance of tandem solar cells, optical simulation based on experimentally feasible values is performed. A maximum PCE of 21% is theoretically achievable for an organic tandem solar cell based on the optimized bandgaps and achieved fill factors.