High‐Output Triboelectric Nanogenerator Based on Dual Inductive and Resonance Effects‐Controlled Highly Transparent Polyimide for Self‐Powered Sensor Network Systems

High‐output triboelectric nanogenerators (TENGs) are demonstrated based on polyimide (PI)‐based polymers by introducing functionalities (e.g., electron‐withdrawing and electron‐donating groups) into the backbone. The TENG based on 6FDA‐APS PI, possessing the most negative electrostatic potential and the low‐lying lowest unoccupied molecular orbital level, produces the highest effective charge density of about 860 µC m^?2 in practical working conditions with the ion injection process. This may be ascribed to the excellent charge‐retention characteristics as well as the enhanced charge transfer capability, which increases the output power by 7 times compared to the commercially available Kapton film‐based TENG. Finally, a 6FDA‐APS‐driven sensor network system is demonstrated, providing the identity of three gases (H₂, CO, and NO₂) by illuminating the light‐emitting diodes within several seconds.     

“Water‐in‐Salt” Electrolyte Makes Aqueous Sodium‐Ion Battery Safe,Green, and Long‐Lasting

Narrow electrochemical stability window (1.23 V) of aqueous electrolytes is always considered the key obstacle preventing aqueous sodium‐ion chemistry of practical energy density and cycle life. The sodium‐ion water‐in‐salt electrolyte (NaWiSE) eliminates this barrier by offering a 2.5 V window through suppressing hydrogen evolution on anode with the formation of a Na⁺‐conducting solid‐electrolyte interphase (SEI) and reducing the overall electrochemical activity of water on cathode. A full aqueous Na‐ion battery constructed on Na_0.66[Mn_0.66Ti_0.34]O₂ as cathode and NaTi₂(PO₄)₃ as anode exhibits superior performance at both low and high rates, as exemplified by extraordinarily high Coulombic efficiency (>99.2%) at a low rate (0.2 C) for >350 cycles, and excellent cycling stability with negligible capacity losses (0.006% per cycle) at a high rate (1 C) for >1200 cycles. Molecular modeling reveals some key differences between Li‐ion and Na‐ion WiSE, and identifies a more pronounced ion aggregation with frequent contacts between the sodium cation and fluorine of anion in the latter as one main factor responsible for the formation of a dense SEI at lower salt concentration than its Li cousin.     

“Closer‐to‐home” strategy benefits juvenile survival in a long‐distance migratory bird

Human‐induced changes in the climate and environment that occur at an unprecedented speed are challenging the existence of migratory species. Faced with these new challenges, species with diverse and flexible migratory behaviors may suffer less from population decline, as they may be better at responding to these changes by altering their migratory behavior. At the individual level, variations in migratory behavior may lead to differences in fitness and subsequently influence the population's demographic dynamics. Using lifetime GPS bio‐logging data from 169 white storks (Ciconia ciconia), we explore whether the recently shortened migration distance of storks affects their survival during different stages of their juvenile life. We also explore how other variations in migratory decisions (i.e., time, destination), movement activity (measured using overall body dynamic acceleration), and early life conditions influence juvenile survival. We observed that their first autumn migration was the riskiest period for juvenile white storks. Individuals that migrated shorter distances and fledged earlier experienced lower mortality risks. In addition, higher movement activity and overwintering “closer‐to‐home” (with 84.21% of the tracked individuals stayed Europe or North Africa) were associated with higher survival. Our study shows how avian migrants can change life history decisions over only a few decades, and thus it helps us to understand and predict how migrants respond to the rapidly changing world.     

Rational Design of Hierarchical “Ceramic‐in‐Polymer” and “Polymer‐in‐Ceramic” Electrolytes for Dendrite‐Free Solid‐State Batteries

Solid polymer electrolytes as one of the promising solid‐state electrolytes have received extensive attention due to their excellent flexibility. However, the issues of lithium (Li) dendrite growth still hinder their practical applications in solid‐state batteries (SSBs). Herein, composite electrolytes from “ceramic‐in‐polymer” (CIP) to “polymer‐in‐ceramic” (PIC) with different sizes of garnet particles are investigated for their effectiveness in dendrite suppression. While the CIP electrolyte with 20 vol% 200 nm Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) particles (CIP‐200 nm) exhibits the highest ionic conductivity of 1.6 × 10^?4 S cm^?1 at 30 °C and excellent flexibility, the PIC electrolyte with 80 vol% 5 µm LLZTO (PIC‐5 µm) shows the highest tensile strength of 12.7 MPa. A sandwich‐type composite electrolyte (SCE) with hierarchical garnet particles (a PIC‐5 µm interlayer sandwiched between two CIP‐200 nm thin layers) is constructed to simultaneously achieve dendrite suppression and excellent interfacial contact with Li metal. The SCE enables highly stable Li plating/stripping cycling for over 400 h at 0.2 mA cm^?2 at 30 °C. The LiFePO₄/SCE/Li cells also demonstrate excellent cycle performance at room temperature. Fabricating sandwich‐type composite electrolytes with hierarchical filler designs can be an effective strategy to achieve dendrite‐free SSBs with high performance and high safety at room temperature.     

Hierarchically Porous,Ultrathick, “Breathable” Wood‐Derived Cathode for Lithium‐Oxygen Batteries

In this work, a hierarchically porous and ultrathick “breathable” wood‐based cathode for high‐performance Li‐O₂ batteries is developed. The 3D carbon matrix obtained from the carbonized and activated wood (denoted as CA‐wood) serves as a superconductive current collector and an ideal porous host for accommodating catalysts. The ruthenium (Ru) nanoparticles are uniformly anchored on the porous wall of the aligned microchannels (denoted as CA‐wood/Ru). The aligned open microchannels inside the carbon matrix contribute to unimpeded oxygen gas diffusion. Moreover, the hierarchical pores on the microchannel walls can be facilely impregnated by electrolyte, forming a continuous supply of electrolyte. As a result, numerous ideal triphase active sites are formed where electrolyte, oxygen, and catalyst accumulate on the porous walls of microchannels. Benefiting from the numerous well‐balanced triple‐phase active sites, the assembled Li‐O₂ battery with the CA‐wood/Ru cathode (thickness: ≈700 µm) shows a high specific area capacity of 8.58 mA h cm^?2 at 0.1 mA cm^?2. Moreover, the areal capacity can be further increased to 56.0 mA h cm^?2 by using an ultrathick CA‐wood/Ru cathode with a thickness of ≈3.4 mm. The facile ultrathick wood‐based cathodes can be applied to other cathodes to achieve a super high areal capacity without sacrificing the electrochemical performance.     

Polymer‐in‐“Quasi‐Ionic Liquid” Electrolytes for High‐Voltage Lithium Metal Batteries

Due to the limited oxidation stability (<4 V) of ether oxygen in its polymer structure, polyethylene oxide (PEO)‐based polymer electrolytes are not compatible with high‐voltage (>4 V) cathodes, thus hinder further increases in the energy density of lithium (Li) metal batteries (LMBs). Here, a new type of polymer‐in‐“quasi‐ionic liquid” electrolyte is designed, which reduces the electron density on ethereal oxygens in PEO and ether solvent molecules, induces the formation of stable interfacial layers on both surfaces of the LiNi_1/3Mn_1/3Co_1/3O₂ (NMC) cathode and the Li metal anode in Li||NMC batteries, and results in a capacity retention of 88.4%, 86.7%, and 79.2% after 300 cycles with a charge cutoff voltage of 4.2, 4.3, and 4.4 V for the LMBs, respectively. Therefore, the use of “quasi‐ionic liquids” is a promising approach to design new polymer electrolytes for high‐voltage and high‐specific‐energy LMBs.     

Strong “bottom‐up” influences on small mammal populations: State‐space model analyses from long‐term studies

“Bottom‐up” influences, that is, masting, plus population density and climate, commonly influence woodland rodent demography. However, “top‐down” influences (predation) also intervene. Here, we assess the impacts of masting, climate, and density on rodent populations placed in the context of what is known about “top‐down” influences. To explain between‐year variations in bank vole Myodes glareolus and wood mouse Apodemus sylvaticus population demography, we applied a state‐space model to 33 years of catch‐mark‐release live‐trapping, winter temperature, and precise mast‐collection data. Experimental mast additions aided interpretation. Rodent numbers in European ash Fraxinus excelsior woodland were estimated (May/June, November/December). December–March mean minimum daily temperature represented winter severity. Total marked adult mice/voles (and juveniles in May/June) provided density indices validated against a model‐generated population estimate; this allowed estimation of the structure of a time‐series model and the demographic impacts of the climatic/biological variables. During two winters of insignificant fruit‐fall, 6.79 g/m² sterilized ash seed (as fruit) was distributed over an equivalent woodland similarly live‐trapped. September–March fruit‐fall strongly increased bank vole spring reproductive rate and winter and summer population growth rates; colder winters weakly reduced winter population growth. September–March fruit‐fall and warmer winters marginally increased wood mouse spring reproductive rate and September–December fruit‐fall weakly elevated summer population growth. Density dependence significantly reduced both species' population growth. Fruit‐fall impacts on demography still appeared after a year. Experimental ash fruit addition confirmed its positive influence on bank vole winter population growth with probable moderation by colder temperatures. The models show the strong impact of masting as a “bottom‐up” influence on rodent demography, emphasizing independent masting and weather influences; delayed effects of masting; and the importance of density dependence and its interaction with masting. We conclude that these rodents show strong “bottom‐up” and density‐dependent influences on demography moderated by winter temperature. “Top‐down” influences appear weak and need further investigation.     

Conductive Li3.08Cr0.02Si0.09V0.9O4 Anode Material: Novel “Zero‐Strain” Characteristic and Superior Electrochemical Li+ Storage

“Zero‐strain” compounds are ideal energy‐storage materials for long‐term cycling because they present negligible volume change and significantly reduce the mechanically induced deterioration during charging–discharging. However, the explored “zero‐strain” compounds are very limited, and their energy densities are low. Here, γ phase Li_3.08Cr_0.02Si_0.09V_0.9O₄ (γ‐LCSVO) is explored as an anode compound for lithium‐ion batteries, and surprisingly its “zero‐strain” Li⁺ storage during Li⁺ insertion–extraction is found through using various state‐of‐the‐art characterization techniques. Li⁺ sequentially inserts into the 4c(1) and 8d sites of γ‐LCSVO, but its maximum unit‐cell volume variation is only ≈0.18%, the smallest among the explored “zero‐strain” compounds. Its mean strain originating from Li⁺ insertion is only 0.07%. Consequently, both γ‐LCSVO nanowires (γ‐LCSVO‐NW) and micrometer‐sized particles (γ‐LCSVO‐MP) exhibit excellent cycling stability with 90.1% and 95.5% capacity retention after as long as 2000 cycles at 10C, respectively. Moreover, γ‐LCSVO‐NW and γ‐LCSVO‐MP respectively deliver large reversible capacities of 445.7 and 305.8 mAh g^?1 at 0.1C, and retain 251.2 and 78.4 mAh g^?1 at 10C. Additionally, γ‐LCSVO shows a suitably safe operating potential of ≈1.0 V, significantly lower than that of the famous “zero‐strain” Li₄Ti₅O₁₂ (≈1.6 V). These merits demonstrate that γ‐LCSVO can be a practical anode compound for stable, high‐energy, fast‐charging, and safe Li⁺ storage.     

Electron‐Beam‐Related Studies of Halide Perovskites: Challenges and Opportunities

Electron beam microscopy and related characterization techniques play an important role in revealing the microstructural, morphological, physical, and chemical information of halide perovskites and their impact on associated optoelectronic devices. However, electron beam irradiation usually causes damage to these beam‐sensitive materials, negatively impacting their device performance, and complicating this interpretation. In this article, the electron microscopy and spectroscopy techniques are reviewed that are crucial for the understanding of the crystallization and microstructure of halide perovskites. In addition, special attention is paid to assessing and mitigating the electron beam‐induced damage caused by these techniques. Since the halide perovskites are fragile, a protocol involving delicate control of both electron beam dose and dose rate, coupled with careful data analysis, is key to enable the acquisition of reliable structural and compositional information such as atomic‐resolution images, chemical elemental mapping and electron diffraction patterns. Limiting the electron beam dose is critical parameter enabling the characterization of various halide perovskites. Novel methods to unveil the mechanisms of device operation, including charge carrier generation, diffusion, and extraction are presented in scanning electron microscopy studies combined with electron‐beam‐induced current and cathodoluminescence mapping. Future opportunities for electron‐beam‐related characterizations of halide perovskites are also discussed.     

“Active” and “passive” ecological restoration strategies in meta‐analysis

One of the means of creating a more robust methodology for ecological restoration involves reducing the gap between ecological theory and restoration practices. A common strategy to do so is using meta‐analysis to understand key drivers of restoration outcomes. “Active” and “passive” is a dichotomy often used to separate restoration strategies in such meta‐analyses. We investigate previously raised concerns about selection bias and subjective categorization of strategies. We promote a paired experimental design in future empirical research and propose the use of three categories of restoration strategy in lieu of “passive” and “active” to alleviate inconsistency in definitions and categorization.     

6‐Methyl 3‐chromonyl 2,4‐thiazolidinedione/2,4‐imidazolidinedione/2‐thioxo‐imidazolidine‐4‐one compounds: novel scavengers of reactive oxygen species

The benefits of antioxidants on human health are usually ascribed to their potential ability to remove reactive oxygen species providing protection against oxidative stress. In this paper the free radicals scavenging activities of nine 6‐methyl 3‐chromonyl derivatives (CMs) were evaluated for the first time by the chemiluminescence, electron paramagnetic resonance, spin trapping and 2,2‐diphenyl‐1‐picrylhydrazyl (DPPH^?) methods. The total antioxidant capacity was also measured using a ferric‐ferrozine reagent. Compounds having a hydrogen atom at the N3‐position of the β‐ring were effective in quenching CL resulted from the KO₂/18‐crown‐6‐ether system (a source of superoxide anion radical, ) in a dose‐dependent manner over the range of 0.05–1 mmol/L [IC₅₀ ranged from 0.353 (0.04) to 0.668 (0.05) mmol/L]. The examined compounds exhibited a significant scavenging effect towards hydroxyl radicals (HO^? HO^?), produced by the Fenton reaction, and this ranged from 24.0% to 61.0%, at the concentration of 2.5 mmol/L. Furthermore, the compounds examined were also found to inhibit DPPH^? and this ranged from 51.9% to 97.4% at the same concentration. In addition, the use of the total antioxidant capacity assay confirmed that CM compounds are able to act as reductants. According to the present study, CM compounds showed effective in vitro free radical scavenging activity and may be considered as potential therapeutics to control diseases of oxidative stress‐related etiology. Copyright © 2013 John Wiley & Sons, Ltd.     

Investigating the bifunctionality of cyclizing and “classical” 5‐aminolevulinate synthases

The precursor to all tetrapyrroles is 5‐aminolevulinic acid, which is made either via the condensation of glycine and succinyl‐CoA catalyzed by an ALA synthase (the C4 or Shemin pathway) or by a pathway that uses glutamyl‐tRNA as a precursor and involves other enzymes (the C5 pathway). Certain ALA synthases also catalyze the cyclization of ALA‐CoA to form 2‐amino‐3‐hydroxycyclopent‐2‐en‐1‐one. Organisms with synthases that possess this second activity nevertheless rely upon the C5 pathway to supply ALA for tetrapyrrole biosynthesis. The C₅N units are components of a variety of secondary metabolites. Here, we show that an ALA synthase used exclusively for tetrapyrrole biosynthesis is also capable of catalyzing the cyclization reaction, albeit at much lower efficiency than the dedicated cyclases. Two absolutely conserved serines present in all known ALA‐CoA cyclases are threonines in all known ALA synthases, suggesting they could be important in distinguishing the functions of these enzymes. We found that purified mutant proteins having single and double substitutions of the conserved residues are not improved in their respective alternate activities; rather, they are worse. Protein structural modeling and amino acid sequence alignments were explored within the context of what is known about the reaction mechanisms of these two different types of enzymes to consider what other features are important for the two activities.     

A critique of the “ultra‐high risk” and “transition” paradigm

The transdiagnostic expression of psychotic experiences in common mental disorder (anxiety/depression/substance use disorder) is associated with a poorer prognosis, and a small minority of people may indeed develop a clinical picture that meets criteria for schizophrenia. However, it appears neither useful nor valid to observe early states of multidimensional psychopathology in young people through the “schizo”‐prism, and apply misleadingly simple, unnecessary and inefficient binary concepts of “risk” and “transition”. A review of the “ultra‐high risk” (UHR) or “clinical high risk” (CHR) literature indicates that UHR/CHR samples are highly heterogeneous and represent individuals diagnosed with common mental disorder (anxiety/depression/substance use disorder) and a degree of psychotic experiences. Epidemiological research has shown that psychotic experiences are a (possibly non‐causal) marker of the severity of multidimensional psychopathology, driving poor outcome, yet notions of “risk” and “transition” in UHR/CHR research are restrictively defined on the basis of positive psychotic phenomena alone, ignoring how baseline differences in multidimensional psychopathology may differentially impact course and outcome. The concepts of “risk” and “transition” in UHR/CHR research are measured on the same dimensional scale, yet are used to produce artificial diagnostic shifts. In fact, “transition” in UHR/CHR research occurs mainly as a function of variable sample enrichment strategies rather than the UHR/CHR “criteria” themselves. Furthermore, transition rates in UHR/CHR research are inflated as they do not exclude false positives associated with the natural fluctuation of dimensional expression of psychosis. Biological associations with “transition” thus likely represent false positive findings, as was the initial claim of strong effects of omega‐3 polyunsatured fatty acids in UHR samples. A large body of UHR/CHR intervention research has focused on the questionable outcome of “transition”, which shows lack of correlation with functional outcome. It may be more productive to consider the full range of person‐specific psychopathology in all young individuals who seek help for mental health problems, instead of “policing” youngsters for the transdiagnostic dimension of psychosis. Instead of the relatively inefficient medical high‐risk approach, a public health perspective, focusing on improved access to a low‐stigma, high‐hope, small scale and youth‐specific environment with acceptable language and interventions may represent a more useful and efficient strategy.     

Near‐Infrared,Heavy Metal‐Free Colloidal “Giant” Core/Shell Quantum Dots

“Giant” core/shell quantum dots (g‐QDs) are a promising class of materials for future optoelectronic technologies due to their superior chemical‐ and photostability compared to bare QDs and core/thin shell QDs. However, inadequate light absorption in the visible and near‐infrared (NIR) region and frequent use of toxic heavy metals (e.g., Cd and Pb) are still major challenges for most g‐QDs (e.g., CdSe/CdS) synthesized to date. The synthesis of NIR, heavy metal‐free, Zn‐treated spherical CuInSe₂/CuInS₂ g‐QDs is reported using the sequential cation exchange method. These g‐QDs exhibit tunable NIR optical absorption and photoluminescence (PL) properties. Transient fluorescence spectroscopy shows prolonged lifetime with increasing shell thickness, indicating the formation of quasi type‐II band alignment, which is further confirmed by simulations. As a proof‐of‐concept, as‐synthesized g‐QDs are used to sensitize TiO₂ as a photoanode in a photoelectrochemical (PEC) cell, demonstrating an efficient and stable PEC system. These results pave the way toward synthesizing NIR heavy metal‐free g‐QDs, which are very promising components of future optoelectronic technologies.