木质纤维素预处理技术研究进展

详细评述了木质纤维素的预处理工艺研究进展,特别是浓酸低温水解-酸回收工艺、稀酸二阶段水解工艺、金属离子在稀酸水解过程中的助催化作用以及水蒸汽爆裂、氨纤维爆裂、CO2爆裂、酶催化水解等方法的研究进展情况。木质纤维素原料预处理技术发展为发酵生产乙醇技术的研究开发奠定了坚实基础。     

一株葡萄糖和木糖共发酵高效产乙醇重组运动发酵单胞菌的性能评价

木糖是木质纤维素原料水解液中的第二大组分,木糖和葡萄糖的充分利用是有经济性地生产纤维素乙醇的关键。通过基因克隆手段构建了一株可以高效利用木糖产乙醇的重组运动发酵单胞菌Zymomonas mobilis TSH01,并进行了利用单糖溶液、混合糖溶液及玉米秸秆水解液发酵产乙醇效率的研究。结果表明,利用单一葡萄糖或单一木糖溶液发酵时,当糖浓度为8%、发酵72 h后,糖利用率分别为100%和98.9%,乙醇代谢收率分别为87.8%和78.3%;利用8%葡萄糖和8%木糖的混合溶液发酵时,72 h后,葡萄糖和木糖的利用率分别为98.5%和97.4%,乙醇代谢收率为94.9%。利用含3.2%葡萄糖和3.5%木糖的玉米秸秆水解液发酵72 h后,葡萄糖和木糖的利用率分别为100%和92.3%,乙醇代谢收率为91.5%。此外,磷酸二氢钾对发酵过程中木糖利用率以及乙醇收率的提高有明显促进作用。     

沙柳原料高浓度底物酶解发酵乙醇工艺

为了提高沙柳生物转化过程的经济可行性,考察了沙柳原料经过蒸爆、超微粉碎+稀酸、超微粉碎+稀碱预处理后高浓度底物补料酶解的效果,并对其高浓度水解糖液进行了乙醇发酵。结果表明:蒸爆处理法水解效果最好,通过补料酶解,底物质量分数可以达到30%,酶解液中总糖质量浓度达到132 g/L,葡萄糖质量浓度105 g/L;超微粉碎+稀酸预处理原料底物质量分数可以达到22%,酶解液中总糖质量浓度达到123 g/L,葡萄糖质量浓度73 g/L;超微粉碎+稀碱预处理原料底物质量分数可以达到22%,酶解液中总糖质量浓度133 g/L,葡萄糖质量浓度77 g/L。3种预处理使沙柳原料的酶解糖液都可以较好地被酿酒酵母利用发酵产乙醇,蒸爆处理原料的酶解糖液乙醇发酵效果最好,乙醇质量浓度达到47 g/L。     

基因组改组及其在木质纤维素水解液乙醇发酵菌种选育中的应用展望

能高效代谢木质纤维素水解液中的可发酵糖、同时可耐受/分解发酵抑制剂的菌种, 是利用木质纤维素为原料生产燃料乙醇技术的关键。基因组改组技术是近些年发展起来的一项新型育种技术, 该技术已运用于食品和医药行业菌种的改良。本文综述了基因组改组技术的原理、方法、特点、及其运用, 并对其在木质纤维素水解液乙醇发酵菌种选育方面的应用进行了展望。     

代谢木糖产乙醇的酿酒酵母工程菌研究进展

随着能源价格的持续上涨,使用木质纤维素生产燃料乙醇已具有重要的实践意义.木糖是多数木质纤维素水解产物中含量仅次于葡萄糖的一种单糖,传统乙醇生产菌株酿酒酵母不能利用木糖,这为使用以木质纤维素为原料发酵生产乙醇带来了困难.多年以来人们试图通过基因工程和细胞融合等方法对其进行改造使其能够代谢木糖生产乙醇.本文主要介绍这方面的研究进展.     

发酵五碳糖和六碳糖产乙醇的细菌研究进展*

农作物废弃物中含有大量木质纤维素,经预处理或水解后能得到各种糖类的混合物,这些糖包括五碳糖和六碳糖(混合糖)。中报道了国内外近20年来在利用细菌发酵混合糖产乙醇方面的研究进展。重点介绍了几种重组大肠杆菌Escherichia coli和运动发酵单胞菌Zymomonas mobilis利用混合糖产乙醇的特性。     

响应曲面优化秸秆稀酸水解工艺用于发酵产壳聚糖

为实现利用秸秆水解产生的五碳糖发酵产壳聚糖,以米根霉为研究对象,研究水解温度、水解时间、酸浓度等不同预处理方式获得的半纤维素水解液对米根霉发酵产壳聚糖的影响。结果表明:水解温度、水解时间对水解液中木糖含量以及甲酸、乙酸、糠醛等抑制剂浓度具有显著影响,并进一步影响后续发酵产壳聚糖的生成量。利用响应曲面对稀酸水解预处理条件进行优化,获得最佳工艺条件:H_2SO_413.6 g/L,99.5℃,水解时间1.91 h,在此条件下预测壳聚糖发酵产量为0.79 g/L,实验验证产量为0.82 g/L,占菌体生物量的15%~18%。研究结果为秸秆资源的高效利用及发酵生产壳聚糖提供新思路。     

混合糖发酵重组酿酒酵母的菌株构建和菊芋秸秆同步糖化发酵研究

【目的】构建可用于纤维素乙醇高效生产的混合糖发酵重组酿酒酵母菌株,并利用菊芋秸秆为原料进行乙醇发酵。【方法】筛选在木糖中生长较好的酿酒酵母YB-2625作为宿主菌,构建木糖共代谢菌株YB-2625 CCX。进一步通过r DNA位点多拷贝整合的方式,以YB-2625 CCX为出发菌株构建木糖脱氢酶过表达菌株,并筛选得到优势菌株YB-73。采用同步糖化发酵策略研究YB-73的菊芋秸秆发酵性能。【结果】YB-73菌株以90 g/L葡萄糖和30 g/L木糖为碳源进行混合糖发酵,乙醇产量比出发菌株YB-2625 CCX提高了13.9%,副产物木糖醇产率由0.89 g/g降低至0.31 g/g,下降了64.6%。利用重组菌YB-73对菊芋秸秆进行同步糖化发酵,48 h最高乙醇浓度达到6.10%(体积比)。【结论】通过转入木糖代谢途径以及r DNA位点多拷贝整合过表达木糖脱氢酶基因可有效提高菌株木糖发酵性能,并用于菊芋秸秆的纤维素乙醇生产。这是首次报道利用重组酿酒酵母进行菊芋秸秆原料的纤维素乙醇发酵。     

代谢木糖产乙醇的酿酒酵母工程菌研究进展

随着能源价格的持续上涨, 使用木质纤维素生产燃料乙醇已具有重要的实践意义。木糖是多数木质纤维素水解产物中含量仅次于葡萄糖的一种单糖, 传统乙醇生产菌株酿酒酵母不能利用木糖, 这为使用以木质纤维素为原料发酵生产乙醇带来了困难。多年以来人们试图通过基因工程和细胞融合等方法对其进行改造使其能够代谢木糖生产乙醇。本文主要介绍这方面的研究进展。     

休哈塔假丝酵母发酵木糖制乙醇过程研究

木质纤维素原料水解产物的主要成分是葡萄糖和木糖,其中葡萄糖很容易发酵,致使木糖成为木质纤维素发酵的关键,休哈塔假丝酵母(Candida shehatae)1766是自然界木糖发酵性能较好的天然酵母之一。研究了发酵温度、发酵时间、接种量、初始pH值、摇床转速等因素对休哈塔假丝酵母1766发酵木糖生产乙醇的影响,由正交试验初步确定了休哈塔假丝酵母发酵木糖制乙醇工艺的适宜条件为好氧条件,发酵时间为2d,发酵温度为28℃,摇床转速为150r/min,初始pH值为5,此时乙醇收率最高可达68.62%。     

Ethanolic fermentation of hydrolysates from ammonia fiber expansion (AFEX) treated corn stover and distillers grain without detoxification and external nutrient supplementation

External nutrient supplementation and detoxification of hydrolysate significantly increase the production cost of cellulosic ethanol. In this study, we investigated the feasibility of fermenting cellulosic hydrolysates without washing, detoxification or external nutrient supplementation using ethanologens Escherichia coli KO11 and the adapted strain ML01 at low initial cell density (16 mg dry weight/L). The cellulosic hydrolysates were derived from enzymatically digested ammonia fiber expansion (AFEX)-treated corn stover and dry distiller's grain and solubles (DDGS) at high solids loading (18% by weight). The adaptation was achieved through selective evolution of KO11 on hydrolysate from AFEX-treated corn stover. All cellulosic hydrolysates tested (36-52 g/L glucose) were fermentable. Regardless of strains, metabolic ethanol yields were near the theoretical limit (0.51 g ethanol/g consumed sugar). Volumetric ethanol productivity of 1.2 g/h/L was achieved in fermentation on DDGS hydrolysate and DDGS improved the fermentability of hydrolysate from corn stover. However, enzymatic hydrolysis and xylose utilization during fermentation were the bottlenecks for ethanol production from corn stover at these experimental conditions. In conclusion, fermentation under the baseline conditions was feasible. Utilization of nutrient-rich feedstocks such as DDGS in fermentation can replace expensive media supplementation.     

Optimization of a synthetic mixture composed of major Trichoderma reesei enzymes for the hydrolysis of steam-exploded wheat straw

Background

The commercialization of second-generation bioethanol has not been realized due to several factors, including poor biomass utilization and high production cost. It is generally accepted that the most important parameters in reducing the production cost are the ethanol yield and the ethanol concentration in the fermentation broth. Agricultural residues contain large amounts of hemicellulose, and the utilization of xylose is thus a plausible way to improve the concentration and yield of ethanol during fermentation. Most naturally occurring ethanol-fermenting microorganisms do not utilize xylose, but a genetically modified yeast strain, TMB3400, has the ability to co-ferment glucose and xylose. However, the xylose uptake rate is only enhanced when the glucose concentration is low.

Results

Separate hydrolysis and co-fermentation of steam-pretreated wheat straw (SPWS) combined with wheat-starch hydrolysate feed was performed in two separate processes. The average yield of ethanol and the xylose consumption reached 86% and 69%, respectively, when the hydrolysate of the enzymatically hydrolyzed (18.5% WIS) unwashed SPWS solid fraction and wheat-starch hydrolysate were fed to the fermentor after 1 h of fermentation of the SPWS liquid fraction. In the other configuration, fermentation of the SPWS hydrolysate (7.0% WIS), resulted in an average ethanol yield of 93% from fermentation based on glucose and xylose and complete xylose consumption when wheat-starch hydrolysate was included in the feed. Increased initial cell density in the fermentation (from 5 to 20 g/L) did not increase the ethanol yield, but improved and accelerated xylose consumption in both cases.

Conclusions

Higher ethanol yield has been achieved in co-fermentation of xylose and glucose in SPWS hydrolysate when wheat-starch hydrolysate was used as feed, then in co-fermentation of the liquid fraction of SPWS fed with the mixed hydrolysates. Integration of first-generation and second-generation processes also increases the ethanol concentration, resulting in a reduction in the cost of the distillation step, thus improving the process economics.     

Detoxification of acidic catalyzed hydrolysate of Kappaphycus alvarezii (cottonii)

Red seaweed, Kappaphycus alvarezii, holds great promise for use in biofuel production due to its high carbohydrate content. In this study, we investigated the effect of fermentation inhibitors to the K. alvarezii hydrolysate on cell growth and ethanol fermentation. In addition, detoxification of fermentation inhibitors was performed to decrease the fermentation inhibitory effect. 5-Hydroxymethylfurfural and levulinic acid, which are liberated from acidic hydrolysis, was also observed in the hydrolysate of K. alvarezii. These compounds inhibited ethanol fermentation. In order to remove these inhibitors, activated charcoal and calcium hydroxide were introduced. The efficiency of activated charcoals was examined and over-liming was used to remove the inhibitors. Activated charcoal was found to be more effective than calcium hydroxide to remove the inhibitors. Detoxification by activated charcoal strongly improved the fermentability of dilute acid hydrolysate in the production of bioethanol from K. alvarezii with Saccharomyces cerevisiae. The optimal detoxifying conditions were found to be below an activated charcoal concentration of 5%.     

Fermentation of sunflower seed hull hydrolysate to ethanol by Pichia stipitis

Ethanol production from sunflower seed hull hydrolysate was evaluated using Pichia stipitis NRRL Y-7124. The hydrolysate prepared with 0.7 M H2SO4 at 90 degrees C was fermented as substrate in shaking bath experiments at 30 degrees C. In a group of experiments, the influence of various detoxification methods on the fermentability of hydrolysate was investigated at pH 6. Even though the ability of all employed pretreatments to enhance fermentation performance was close, the sequential application of overliming with sodium sulfite addition was the best detoxification method. Additional experiments were performed with detoxified hydrolysate to investigate the effect of shaking rate (70-130 rpm) and initial pH (5.5-7) on the fermentation. The highest ethanol level 11 gL(-1) was achieved at initial pH of 6 and 100 rpm shaking rate from a hydrolysate containing 48 gL(-1) total reducing sugar. The corresponding alcohol yield and volumetric productivity were 0.32 gg(-1) and 0.065 gL(-1)h(-1).     

Conversion of corn fiber to ethanol by recombinant E. coli strain FBR3

Escherichia coli strain FBR3 that is an efficient biocatalyst for converting mixed sugar streams (eg, arabinose, glucose, and xylose) into ethanol. In this report, the strain was tested for conversion of corn fiber hydrolysates into ethanol. Corn fiber hydrolysates with total sugar concentrations of 7.5% (w/v) were prepared by reacting corn fiber with dilute sulfuric acid at 145°C. Initial fermentations of the hydrolysate by strain FBR3 had lag times of approximately 30 h judged by ethanol production. Further experiments indicated that the acetate present in the hydrolysate could not solely account for the long lag. The lag phase was greatly reduced by growing the pre-seed and seed cultures on corn fiber hydrolysate. Ethanol yields for the optimized fermentations were 90% of theoretical. Maximum ethanol concentrations were 2.80% w/v, and the fermentations were completed in approximately 50 h. The optimal pH for the fermentation was 6.5. Below this pH, sugar consumption was incomplete and above it, excess base addition was required throughout the fermentation. Two alternative neutralization methods (overliming and overliming with sulfite addition) have been reported for improving the fermentability of lignocellulosic hydrolysates. These methods further reduced the lag phase of the fermentation, albeit by a minor amount. Received 29 September 1998/ Accepted in revised form 20 February 1999     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

The acid hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol sulfuric acid per liter pyrolysate using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol in 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol in 18 h. The results showed that the acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by S. cerevisiae (R) in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Ethanol fermentation of acid-hydrolyzed cellulosic pyrolysate with Saccharomyces cerevisiae

Acid-hydrolysis of cellulosic pyrolysate to glucose and its fermentation to ethanol were investigated. The maximum glucose yield (17.4%) was obtained by the hydrolysis with 0.2 mol/l sulfuric acid using autoclaving at 121 degrees C for 20 min. The fermentation by Saccharomyces cerevisiae of a hydrolysate medium containing 31.6 g/l glucose gave 14.2 g/l ethanol after 24 h, whereas the fermentation of the medium containing 31.6 g/l pure glucose gave 13.7 g/l ethanol after 18 h. The results showed that acid-hydrolyzed pyrolysate could be used for ethanol production. Different nitrogen sources were evaluated and the best ethanol concentration (15.1 g/l) was achieved by single urea. S. cerevisiae (R) was obtained by adaptation of S. cerevisiae to the hydrolysate medium for 12 times, and 40.2 g/l ethanol was produced by it in the fermentation with the hydrolysate medium containing 95.8 g/l glucose, which was about 47% increase in ethanol production compared to its parent strain.     

Comparative fermentability of enzymatic and acid hydrolysates of steam-pretreated aspenwood hemicellulose by Pichia stipitis CBS 5776

Summary Enzymatic hydrolysates of hemicellulose from steam-pretreated aspenwood were more fermentable than the acid hydrolysate after rotoevaporation or ethyl acetate extraction treatments to remove acetic acid and sugar- and lignin-degradation products prior to fermentation by Pichia stipitis CBS 5776. Total xylose and xylobiose utilization from 5.0% (w/v) ethyl acetate extracted enzymatic hydrolysate was observed with an ethanol yield of 0.47 g ethanol/g total available substrate and an ethanol production rate of 0.20 g·l^-1 per hour in 72 h batch fermentation.     

Bioethanol from fermentation of cassava pulp in a fibrous-bed bioreactor using immobilized Δldh, a genetically engineered Thermoanaerobacterium aotearoense

There is an increasing worldwide interest in bioethanol production from agricultural, industrial, and urban residues for both ecological and economic reasons. The acid hydrolysis of cassava pulp to reducing sugars and their fermentation to ethanol were evaluated in a fibrousbed bioreactor with immobilized Δldh, a genetically engineered Thermoanaerobacterium aotearoense. A maximum yield of total reducing sugars of 53.5% was obtained after 8 h of hydrolysis at 85oC in 0.4 mol/L hydrochloric acid with a solid-to-liquid ratio of 1:20, which was optimized by using an orthogonal design based on preliminary experiments. In the FBB, the fed-batch fermentation, using glucose as the sole carbon source, gave a maximum ethanol production of 38.3 g/L with a yield of 0.364 g/g in 100 h; whereas the fed-batch fermentation, using xylose as the sole carbon source, gave 34.1 g/L ethanol with a yield of 0.342 g/g in 135 h. When cassava pulp hydrolysate was used as a carbon source, 39.1 g/L ethanol with a yield of 0.123 g/g cassava pulp in185 h was observed, using the fed-batch fermentation model. In addition, for repeated batch fermentation of cassava pulp hydrolysate carried out in the fibrous-bed bioreactor, long-term operation with high ethanol yield and volumetric productivity were achieved. The above results show that the acid hydrolysate of cassava pulp can be used for ethanol production in a fibrous-bed bioreactor, although some inhibition phenomena were observed during the process of fermentation.     

亚硫酸盐甘蔗渣浆酶解液发酵制备乙醇

以亚硫酸盐甘蔗渣浆酶解液作为原料,利用C. shehatae发酵制取燃料乙醇。结果表明：还原糖最适初始质量浓度为葡萄糖140 g/L、木糖60 g/L、酶解液总糖80 g/L。利用初始葡萄糖55.06 g/L、木糖11.18 g/L、纤维二糖4.51 g/L的亚硫酸盐甘蔗渣浆酶解液发酵,经18 h获得乙醇22.98 g/L。乙醇得率为67.23%,葡萄糖利用率为99.27%,木糖利用率为32.96%,C. shehatae适合作为蔗渣为原料的乙醇发酵菌株。