Long-term cathode performance and the microbial communities that develop in microbial fuel cells fed different fermentation endproducts

To better understand how cathode performance and substrates affected communities that evolved in these reactors over long periods of time, microbial fuel cells were operated for more than 1 year with individual endproducts of lignocellulose fermentation (acetic acid, formic acid, lactic acid, succinic acid, or ethanol). Large variations in reactor performance were primarily due to the specific substrates, with power densities ranging from 835 ± 21 to 62 ± 1 mW/m³. Cathodes performance degraded over time, as shown by an increase in power of up to 26% when the cathode biofilm was removed, and 118% using new cathodes. Communities that developed on the anodes included exoelectrogenic families, such as Rhodobacteraceae, Geobacteraceae, and Peptococcaceae, with the Deltaproteobacteria dominating most reactors. Pelobacter propionicus was the predominant member in reactors fed acetic acid, and it was abundant in several other MFCs. These results provide valuable insights into the effects of long-term MFC operation on reactor performance.     

Electricity generation and microbial community changes in microbial fuel cells packed with different anodic materials

Four materials, carbon felt cube (CFC), granular graphite (GG), granular activated carbon (GAC) and granular semicoke (GS) were tested as packed anodic materials to seek a potentially practical material for microbial fuel cells (MFCs). The microbial community and its correlation with the electricity generation performance of MFCs were explored. The maximum power density was found in GAC, followed by CFC, GG and GS. In GAC and CFC packed MFCs, Geobacter was the dominating genus, while Azospira was the most populous group in GG. Results further indicated that GAC was the most favorable for Geobacter adherence and growth, and the maximum power densities had positive correlation with the total biomass and the relative abundance of Geobacter, but without apparent correlation with the microbial diversity. Due to the low content of Geobacter in GS, power generated in this system may be attributed to other microorganisms such as Synergistes, Bacteroidetes and Castellaniella.     

Electricity-producing bacterial communities in microbial fuel cells

Microbial fuel cells (MFCs) are not yet commercialized but they show great promise as a method of water treatment and as power sources for environmental sensors. The power produced by these systems is currently limited, primarily by high internal (ohmic) resistance. However, improvements in the system architecture will soon result in power generation that is dependent on the capabilities of the microorganisms. The bacterial communities that develop in these systems show great diversity, ranging from primarily delta-Proteobacteria that predominate in sediment MFCs to communities composed of alpha-, beta-, gamma- or delta-Proteobacteria, Firmicutes and uncharacterized clones in other types of MFCs. Much remains to be discovered about the physiology of these bacteria capable of exocellular electron transfer, collectively defined as a community of "exoelectrogens". Here, we review the microbial communities found in MFCs and the prospects for this emerging bioenergy technology.     

Application of biocathode in microbial fuel cells: cell performance and microbial community

Instead of the utilization of artificial redox mediators or other catalysts, a biocathode has been applied in a two-chamber microbial fuel cell in this study, and the cell performance and microbial community were analyzed. After a 2-month startup, the microorganisms of each compartment in microbial fuel cell were well developed, and the output of microbial fuel cell increased and became stable gradually, in terms of electricity generation. At 20 ml/min flow rate of the cathodic influent, the maximum power density reached 19.53 W/m3, while the corresponding current and cell voltage were 15.36 mA and 223 mV at an external resistor of 14.9 Omega, respectively. With the development of microorganisms in both compartments, the internal resistance decreased from initial 40.2 to 14.0 Omega, too. Microbial community analysis demonstrated that five major groups of the clones were categorized among those 26 clone types derived from the cathode microorganisms. Betaproteobacteria was the most abundant division with 50.0% (37 of 74) of the sequenced clones in the cathode compartment, followed by 21.6% (16 of 74) Bacteroidetes, 9.5% (7 of 74) Alphaproteobacteria, 8.1% (6 of 74) Chlorobi, 4.1% (3 of 74) Deltaproteobacteria, 4.1% (3 of 74) Actinobacteria, and 2.6% (2 of 74) Gammaproteobacteria.     

微生物燃料电池生物质能利用现状与展望

作为一种新概念的废物处理与能源化技术,微生物燃料电池研究在过去10年里取得了长足的进步和技术突破。本文在简要介绍微生物燃料电池研究现状基础上,系统综述了该技术及与其他技术耦合在生物质能利用方面的最新研究进展,重点分析了其中存在的问题,并展望了该技术在生物质能转化和利用方面的研究前景。     

Change in microbial communities in acetate- and glucose-fed microbial fuel cells in the presence of light

Power densities produced by microbial fuel cells (MFCs) in natural systems are changed by exposure to light through the enrichment of photosynthetic microorganisms. When MFCs with brush anodes were exposed to light (4000 lx), power densities increased by 8–10% for glucose-fed reactors, and 34% for acetate-fed reactors. Denaturing gradient gel electrophoresis (DGGE) profiles based on the 16S rRNA gene showed that exposure to high light levels changed the microbial communities on the anodes. Based on 16S rRNA gene clone libraries of light-exposed systems the anode communities using glucose were also significantly different than those fed acetate. Dominant bacteria that are known exoelectrogens were identified in the anode biofilm, including a purple nonsulfur (PNS) photosynthetic bacterium, Rhodopseudomonas palustris, and a dissimilatory iron-reducing bacterium, Geobacter sulfurreducens. Pure culture tests confirmed that PNS photosynthetic bacteria increased power production when exposed to high light intensities (4000 lx). These results demonstrate that power production and community composition are affected by light conditions as well as electron donors in single-chamber air-cathode MFCs.     

Photosynthetic microbial fuel cells with positive light response

The current study introduces an aerobic single‐chamber photosynthetic microbial fuel cell (PMFC). Evaluation of PMFC performance using naturally growing fresh‐water photosynthetic biofilm revealed a weak positive light response, that is, an increase in cell voltage upon illumination. When the PMFC anodes were coated with electrically conductive polymers, the rate of voltage increased and the amplitude of the light response improved significantly. The rapid immediate positive response to light was consistent with a mechanism postulating that the photosynthetic electron‐transfer chain is the source of the electrons harvested on the anode surface. This mechanism is fundamentally different from the one exploited in previously designed anaerobic microbial fuel cells (MFCs), sediment MFCs, or anaerobic PMFCs, where the electrons are derived from the respiratory electron‐transfer chain. The power densities produced in PMFCs were substantially lower than those that are currently reported for conventional MFC (0.95 mW/m² for polyaniline‐coated and 1.3 mW/m² for polypyrrole‐coated anodes). However, the PMFC did not depend on an organic substrate as an energy source and was powered only by light energy. Its operation was CO₂‐neutral and did not require buffers or exogenous electron transfer shuttles. Biotechnol. Bioeng. 2009; 104: 939–946. © 2009 Wiley Periodicals, Inc.     

Effect of different substrates on the performance,bacterial diversity,and bacterial viability in microbial fuel cells

Four microbial fuel cells (MFCs) were inoculated with anaerobic sludge and fed four different substrates for over one year. The Coulombic efficiency (CE) and power output varied with different substrates, while the bacterial viability was similar. Acetate fed-MFC showed the highest CE (72.3%), followed by butyrate (43.0%), propionate (36.0%) and glucose (15.0%). Glucose resulted in the lowest CE because of its fermentable nature implying its consumption by diverse non-electricity-generating bacteria. 16S rDNA sequencing results indicated phylogenetic diversity in the communities of all anode biofilms, and there was no single dominant bacterial species. A relative abundance of β-Proteobacteria but an absence of γ-Proteobacteria was observed in all MFCs except for propionate-fed system in which Firmicutes dominating. The glucose-fed-MFC showed the widest community diversity, resulting in the rapid generation of current without lag time when different substrates were suddenly fed. Geobacter-like species with the most representative Geobactersulfurreducens PCA^T were integral members of the bacterial community in all MFCs except for the propionate-fed system.     

铜绿假单胞菌存活时间延长可提高生物燃料电池的产电量

铜绿假单胞菌产生的次生代谢产物吩嗪化合物具有电子传递作用,可用于构建微生物燃料电池。如何通过改进微生物自身性质来提升微生物燃料电池产电量是研究的热点与难点之一。本文以铜绿假单胞菌SJTD-1和其敲除突变株SJTD-1(ΔmvaT)为对象,研究了以其搭建的微生物燃料电池的放电过程,分析了影响其放电量的主要因素。结果显示,假单胞菌产生的吩嗪化合物和发酵系统中细菌的活性与存活数量均会直接影响燃料电池的产电量。敲除突变株SJTD-1(ΔmvaT)可产生较多的吩嗪化合物,在生物燃料电池系统可持续放电超过160 h,产生2.32 J的总电量;而野生菌株SJTD-1仅能放电90 h,产生1.30 J的总电量。细胞生长分析结果进一步显示,与野生菌株相比,突变菌株SJTD-1(ΔmvaT)在发酵过程中维持了较长的稳定期生长,细胞存活时间更长,放电时间更持久。因此,铜绿假单胞菌存活时间延长,可增加其在微生物燃料电池中的放电时间,从而提升微生物燃料电池的总产电量。本研究可为通过工程菌株改造来提升微生物燃料电池总产电量的研究提供思路,有利于推进微生物燃料电池的实际应用。     

Effect of external resistance on bacterial diversity and metabolism in cellulose-fed microbial fuel cells

External resistance affects the performance of microbial fuel cells (MFCs) by controlling the flow of electrons from the anode to the cathode. The purpose of this study was to determine the effect of external resistance on bacterial diversity and metabolism in MFCs. Four external resistances (20, 249, 480, and 1000 Ω) were tested by operating parallel MFCs independently at constant circuit loads for 10 weeks. A maximum power density of 66 mW m⁻² was achieved by the 20 Ω MFCs, while the MFCs with 249, 480, and 1000 Ω external resistances produced 57.5, 27, and 47 mW m⁻², respectively. Denaturing gradient gel electrophoresis analysis of partial 16S rRNA genes showed clear differences between the planktonic and anode-attached populations at various external resistances. Concentrations of short chain fatty acids were higher in MFCs with larger circuit loads, suggesting that fermentative metabolism dominated over anaerobic respiration using the anode as the final electron acceptor.     

Energy from algae using microbial fuel cells

Bioelectricity production from a phytoplankton, Chlorella vulgaris, and a macrophyte, Ulva lactuca was examined in single chamber microbial fuel cells (MFCs). MFCs were fed with the two algae (as powders), obtaining differences in energy recovery, degradation efficiency, and power densities. C. vulgaris produced more energy generation per substrate mass (2.5 kWh/kg), but U. lactuca was degraded more completely over a batch cycle (73 ± 1% COD). Maximum power densities obtained using either single cycle or multiple cycle methods were 0.98 W/m² (277 W/m³) using C. vulgaris, and 0.76 W/m² (215 W/m³) using U. lactuca. Polarization curves obtained using a common method of linear sweep voltammetry (LSV) overestimated maximum power densities at a scan rate of 1 mV/s. At 0.1 mV/s, however, the LSV polarization data was in better agreement with single‐ and multiple‐cycle polarization curves. The fingerprints of microbial communities developed in reactors had only 11% similarity to inocula and clustered according to the type of bioprocess used. These results demonstrate that algae can in principle, be used as a renewable source of electricity production in MFCs. Biotechnol. Bioeng. 2009;103: 1068–1076. © 2009 Wiley Periodicals, Inc.     

Improving energy accumulation of microbial fuel cells by metabolism regulation using Rhodoferax ferrireducens as biocatalyst

AIMS: To study the physiology and metabolism of microbial cells in the performance of microbial fuel cells (MFCs). METHODS AND RESULTS: A dual-chamber MFCs was constructed, and Rhodoferax ferrireducens was used as biocatalyst. To examine the physiology of microbial cells in the performance of MFCs, the anode media containing planktonic cells was replaced with fresh media in which KH(2)PO(4) and/or NH(4)Cl were excluded. The replacing of anode media containing planktonic cells with fresh media excluded of KH(2)PO(4) and NH(4)Cl made the coulombic yield remarkably increased by a factor of 68% (from 29.1 to 46.8C). The results showed that the electricity could be generated with cells in biofilms as biocatalyst, and coulombic yield was improved by limiting cell growth via removal of ingredients in anode media. By supplementation of glucose to the anode media when current declined to baseline, MFCs achieved about same platform current values immediately. MFCs could continue to produce electricity for about 30 h even after glucose was below detection. CONCLUSIONS: Biofilms and metabolism of glucose play important roles in the performance of MFCs. Coulombic yield of MFCs could be improved by regulating the media ingredients using the stable biofilms-electrode system. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first attempt to study the effect of ingredient compositions of anode media on the performance of MFCs. The observed results that MFCs continued to produce electricity after glucose was below detection was helpful to better understand the mechanism of microbial electricity production.     

Effect of fiber diameter on the behavior of biofilm and anodic performance of fiber electrodes in microbial fuel cells

A series of fiber electrodes with fiber diameters ranging from about 10 to 0.1 μm were tested as anodes in microbial fuel cells to study the effect of fiber diameter on the behavior of biofilm and anodic performance of fiber electrodes. A simple method of biofilm fixation and dehydration was developed for biofilm morphology characterization. Results showed that the current density of fiber anodes increased until the fiber diameter approached 1 μm which was about the length of the dominant microorganisms in biofilm. The highest current density was 3.08 mA cm(-2), which was obtained from fiber anode with high porosity of over 99% and fiber diameter of 0.87 μm. It was believed that the high current density was attributed to the high porosity, as well as proper fiber diameter which ensured formation of thick and continuous solid biofilms.     

微生物燃料电池在固体废物堆肥中的应用进展

微生物燃料电池(Microbial fuel cell,MFC)是一种近几年快速发展的废物处理与能源化技术,可以与污水处理、污染物降解、脱盐等环境技术结合。微生物燃料电池与堆肥技术结合可以在处理日益增长的固体废弃物的同时回收能量,具有很好的发展前景。文中分析了堆肥微生物燃料电池系统的微生物特征,探讨了堆肥过程中影响微生物燃料电池产电性能的因素,包括电极,隔膜,供氧和构型。最后归纳说明了堆肥微生物电池作为一种新的废弃物处理技术的特点:较高的微生物量并可产生较高的电流密度;对不同环境的适应性强;可以自身调节温度,能源利用效率高;质子从阳极向阴极的移动会受到不同堆肥原料的影响。     

微生物燃料电池在毒性物质检测中的应用

微生物燃料电池(Microbial fuel cell,MFC)利用微生物整体作为催化剂催化底物将化学能直接转化为电能,是一种极具应用前景的生物电化学技术。微生物在阳极氧化还原有机物产生电子并传递给阳极,电子通过外电路传递至阴极后将电子释放给阴极中的氧化剂,从而产生电流。当有毒物质进入MFC,微生物活性降低,电子传递量变少,电流降低,而电流的产生与微生物活性呈线性关系,据此可检测样品的毒性。本文主要介绍了微生物燃料电池在毒性物质抗生素、重金属离子、有机污染物、酸等方面的研究,并分析了微生物燃料电池存在的问题及未来研究方向,以期不久的将来微生物燃料电池能付之使用。     

Electricity generation from cellulose by rumen microorganisms in microbial fuel cells

In microbial fuel cells (MFCs) bacteria generate electricity by mediating the oxidation of organic compounds and transferring the resulting electrons to an anode electrode. The objective of this study was to test the possibility of generating electricity with rumen microorganisms as biocatalysts and cellulose as the electron donor in two-compartment MFCs. The anode and cathode chambers were separated by a proton exchange membrane and graphite plates were used as electrodes. The medium in the anode chamber was inoculated with rumen microorganisms, and the catholyte in the cathode compartment was ferricyanide solution. Maximum power density reached 55 mW/m(2) (1.5 mA, 313 mV) with cellulose as the electron donor. Cellulose hydrolysis and electrode reduction were shown to support the production of current. The electrical current was sustained for over 2 months with periodic cellulose addition. Clarified rumen fluid and a soluble carbohydrate mixture, serving as the electron donors, could also sustain power output. Denaturing gradient gel electrophoresis (DGGE) of PCR amplified 16S rRNA genes revealed that the microbial communities differed when different substrates were used in the MFCs. The anode-attached and the suspended consortia were shown to be different within the same MFC. Cloning and sequencing analysis of 16S rRNA genes indicated that the most predominant bacteria in the anode-attached consortia were related to Clostridium spp., while Comamonas spp. abounded in the suspended consortia. The results demonstrated that electricity can be generated from cellulose by exploiting rumen microorganisms as biocatalysts, but both technical and biological optimization is needed to maximize power output.     

Electrocatalytic activity of anodic biofilm responses to pH changes in microbial fuel cells

This study investigates the effects of anodic pH on electricity generation in microbial fuel cells (MFCs) and the intrinsic reasons behind them. In a two-chamber MFC, the maximum power density is 1170 ± 58 mW m⁻² at pH 9.0, which is 29% and 89% higher than those working at pH 7.0 and 5.0, respectively. Electrochemical measurements reveal that pH affects the electron transfer kinetics of anodic biofilms. The apparent electron transfer rate constant (k_app) and exchange current density (i₀) are greater whereas the charge transfer resistance (R_ct) is smaller at pH 9.0 than at other conditions. Scanning electron microscopy verifies that alkaline conditions benefit biofilm formation in MFCs. These results demonstrate that electrochemical interactions between bacteria and electrodes in MFCs are greatly enhanced under alkaline conditions, which can be one of the important reasons for the improved MFC output.     

Improved fuel cell and electrode designs for producing electricity from microbial degradation

A new one-compartment fuel cell was composed of a rubber bunged bottle with a center-inserted anode and a window-mounted cathode containing an internal, proton-permeable porcelain layer. This fuel cell design was less expensive and more practical than the conventional two-compartment system, which requires aeration and a ferricyanide solution in the cathode compartment. Three new electrodes containing bound electron mediators including a Mn(4+)-graphite anode, a neutral red (NR) covalently linked woven graphite anode, and an Fe(3+)-graphite cathode were developed that greatly enhanced electrical energy production (i.e., microbial electron transfer) over conventional graphite electrodes. The potentials of these electrodes measured by cyclic voltametry at pH 7.0 were (in volts): +0.493 (Fe(3+)-graphite); +0.15 (Mn(4+)-graphite); and -0.53 (NR-woven graphite). The maximal electrical productivities obtained with sewage sludge as the biocatalyst and using a Mn(4+)-graphite anode and a Fe(3+)-graphite cathode were 14 mA current, 0.45 V potential, 1,750 mA/m(2) current density, and 788 mW/m(2) of power density. With Escherichia coli as the biocatalyst and using a Mn(4+)-graphite anode and a Fe(3+)-graphite cathode, the maximal electrical productivities obtained were 2.6 mA current, 0.28 V potential, 325 mA/m(2) current density, and 91 mW/m(2) of power density. These results show that the amount of electrical energy produced by microbial fuel cells can be increased 1,000-fold by incorporating electron mediators into graphite electrodes. These results also imply that sewage sludge may contain unique electrophilic microbes that transfer electrons more readily than E. coli and that microbial fuel cells using the new Mn(4+)-graphite anode and Fe(3+)-graphite cathode may have commercial utility for producing low amounts of electrical power needed in remote locations.     

Submersible microbial fuel cell sensor for monitoring microbial activity and BOD in groundwater: Focusing on impact of anodic biofilm on sensor applicability

A sensor, based on a submersible microbial fuel cell (SUMFC), was developed for in situ monitoring of microbial activity and biochemical oxygen demand (BOD) in groundwater. Presence or absence of a biofilm on the anode was a decisive factor for the applicability of the sensor. Fresh anode was required for application of the sensor for microbial activity measurement, while biofilm‐colonized anode was needed for utilizing the sensor for BOD content measurement. The current density of SUMFC sensor equipped with a biofilm‐colonized anode showed linear relationship with BOD content, to up to 250 mg/L (～233 ± 1 mA/m²), with a response time of <0.67 h. This sensor could, however, not measure microbial activity, as indicated by the indifferent current produced at varying active microorganisms concentration, which was expressed as microbial adenosine‐triphosphate (ATP) concentration. On the contrary, the current density (0.6 ± 0.1 to 12.4 ± 0.1 mA/m²) of the SUMFC sensor equipped with a fresh anode showed linear relationship, with active microorganism concentrations from 0 to 6.52 nmol‐ATP/L, while no correlation between the current and BOD was observed. It was found that temperature, pH, conductivity, and inorganic solid content were significantly affecting the sensitivity of the sensor. Lastly, the sensor was tested with real contaminated groundwater, where the microbial activity and BOD content could be detected in <3.1 h. The microbial activity and BOD concentration measured by SUMFC sensor fitted well with the one measured by the standard methods, with deviations ranging from 15% to 22% and 6% to 16%, respectively. The SUMFC sensor provides a new way for in situ and quantitative monitoring contaminants content and biological activity during bioremediation process in variety of anoxic aquifers. Biotechnol. Bioeng. 2011;108: 2339–2347. © 2011 Wiley Periodicals, Inc.