Monitoring oil production for biobased feedstock in the microalga <Emphasis Type="Italic">Nannochloropsis</Emphasis> sp.: a novel method combining the BODIPY BD-C12 fluorescent probe and simple image processing

A simple reliable method with fast response for lipid detection and quantification is proposed, combining a new highly lipophilic fluorescent probe BODIPY BD-C12 and image analysis to determine the algal lipid content and the lipid production in the microalgae Nannochloropsis sp. Lipid bodies stained with BODIPY BD-C12 have a characteristic multicolor fluorescence, and their volumes were determined using a sphere volume approach. The method developed was applied in the evaluation of lipid accumulation by Nannochloropsis sp. under different cultivation conditions (varying nitrate and salinity concentrations and combined effect of these two variables). The results show an increase of lipid content in Nannochloropsis sp. cultivated in nitrogen replete and depleted conditions, from 9.4 to 40.8 μm³ cell^?1 and 35.5 to 73.5%, respectively. The findings are also compared with conventional methods for determination of neutral lipids and with results obtained from the dyes Nile Red and BODIPY 505/515. A reasonable agreement between neutral lipid production measured by BODIPY BD-C12 and gravimetric methods (correlation coefficient of 0.98) was obtained. The neutral lipids production decreased from 964.6 to 244.8 mg L^?1 and from 809.1 to 396.7 mg L^?1, as the nitrate concentration increased from 0 to 0.3 g L^?1. It is observed that, with the two commercially available dyes, lipid quantification using Nile Red leads to an overestimation of lipids, while the use of BODIPY 505/515 promoted unreliable measures due to rapid bleaching of the chromophore. The method proposed shows excellent potential to become a standard, yet advanced, strategy for rapid evaluation and quantification of intracellular lipids in microalgae, a crucial step of the scaling-up process involved in the production of biobased products.     

Optimization of aeration for biodiesel production by <Emphasis Type="Italic">Scenedesmus obliquus</Emphasis> grown in municipal wastewater

Despite the significant breakthroughs in research on microalgae as a feedstock for biodiesel, its production cost is still much higher than that of fossil diesel. One possible solution to overcome this problem is to optimize algal growth and lipid production in wastewater. The present study examines the optimization of pretreatment of municipal wastewater and aeration conditions in order to enhance the lipid productivity of Scenedesmus obliquus. Results showed that no significant differences were recorded in lipid productivity of S. obliquus grown in primary settled or sterilized municipal wastewater; however, ultrasound pretreatment of wastewater significantly decreased the lipid production. Whereas, aeration rates of 0.2 vvm significantly increased lipid content by 51 %, with respect to the non-aerated culture, which resulted in maximum lipid productivity (32.5 mg L^?1 day^?1). Furthermore, aeration enrichment by 2 % CO₂ resulted in increase of lipid productivity by 46 % over the CO₂ non-enriched aerated culture. Fatty acid profile showed that optimized aeration significantly enhanced monounsaturated fatty acid production, composed mainly of C18:1, by 1.8 times over the non-aerated S. obliquus culture with insignificant changes in polyunsaturated fatty acid proportion; suggesting better biodiesel characteristics for the optimized culture.     

Productivity and biochemical composition of <Emphasis Type="Italic">Tetradesmus obliquus</Emphasis> and <Emphasis Type="Italic">Phaeodactylum tricornutum</Emphasis>: effects of different cultivation approaches

The present work evaluated biomass productivity, carbon dioxide fixation rate, and biochemical composition of two microalgal species, Phaeodactylum tricornutum (Bacillariophyta) and Tetradesmus obliquus (Chlorophyta), cultivated indoors in high-technology photobioreactors (HT-PBR) and outdoors both in pilot ponds and low-technology photobioreactors in a greenhouse in southern Italy. Microalgae were grown in standard media, under nitrogen starvation, and in two liquid digestates obtained from anaerobic digestion of agro-zootechnical and vegetable biomass. P. tricornutum, cultivated in semi-continuous mode in indoor HT-PBRs with standard medium, showed a biomass productivity of 21.0?±?2.3 g m^?2 d^?1. Applying nitrogen starvation, the lipid productivity increased from 2.3 up to 4.5?±?0.5 g m^?2 d^?1, with a 24 % decrease of biomass productivity. For T. obliquus, a biomass productivity of 9.1?±?0.9 g m^?2 d^?1 in indoor HT-PBR was obtained using standard medium. Applying liquid digestates as fertilizers in open ponds, T. obliquus gave a biomass productivity (10.8?±?2.0 g m^?2 d^?1) not statistically different from complete medium such as P. tricornutum (6.5?±?2.2 g m^?2 d^?1). The biochemical data showed that the fatty acid composition of the microalgal biomass was affected by the different cultivation conditions for both microalgae. In conclusion, it was found that the microalgal productivity in standard medium was about doubled in HT-PBR compared to open ponds for P. tricornutum and was about 20 % higher for T. obliquus.     

An alternative strategy for enhancing lipid accumulation in chlorophycean microalgae for biodiesel production

Oleaginous microalgae are considered as important feedstocks for production of biodiesel. Under nutrient stress conditions, microalgae have the ability to accumulate higher amount of lipids, which can be transesterified for the production of biodiesel. In the present investigation, four different phosphate application strategies were examined in five green microalgae (Tetradesmus obliquus, Tetradesmus lagerheimii, Chlorella vulgaris, Chlorella minutissima, and Chlamydomonas sp.) to achieve higher lipid productivity. Effects of those strategies such as phosphate-sufficient (Control), phosphate-starved approach (PSA), biphasic phosphate-starved approach (BPSA), and sequential phosphate addition (SPA) were studied under batch culture mode. The BPSA emerging as the best in terms of lipid productivity consisted of two biomass harvesting phases, which would lead to an increase in the overall cost of biodiesel production. On the other hand, the SPA with a 1/200th dose of N 11 medium, i.e., 0.4 mg L^?1 of phosphate application in 3-day intervals, also resulted into higher lipid productivity which was equal to BPSA. Fatty acid composition of the biodiesel obtained from the microalgae was analyzed and the fuel characteristics were also evaluated. A profound (~14-fold) reduction in phosphorus requirements under the SPA mode with higher lipid productivity ensured qualitative biodiesel production and a lesser amount of phosphorus release, thus making the process eco-friendly.     

Comparison of the culture and harvesting of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> and <Emphasis Type="Italic">Tetradesmus obliquus</Emphasis> for the removal of pharmaceuticals from water

The objective of this work was to assess and compare the removal efficiency of paracetamol and salicylic acid from aqueous medium by a microalgae-based treatment, using either Chlorella vulgaris or Tetradesmus obliquus. Moreover, considering microalgae application in wastewater treatment, the influence of these pharmaceuticals in the algal nutrient removal capacity was evaluated. The removal of paracetamol by T. obliquus (>40 %) was larger than by C. vulgaris (>21 %) in batch culture, and this was also observed for salicylic acid (>93 % by T. obliquus and >25 % by C. vulgaris). Both strains removed nutrients (phosphate and nitrate) almost completely by the end of the batch culture, but T. obliquus showed the highest efficiency at the steady state conditions of the semicontinuous culture. In spite of this, under the flocculants here tested, the efficiency in the recovery of biomass was much higher for C. vulgaris. These results highlight the importance of strain selection in the application of microalgae for wastewater treatment and, particularly, for the removal of pharmaceuticals.     

Utilization of gaseous emissions from a methanol plant for cultivation of <Emphasis Type="Italic">Acutodesmus obliquus</Emphasis>

This study aimed to culture the green alga Acutodesmus obliquus utilizing the gaseous emissions containing a high concentration of CO₂ (99.13 %) from a methanol plant and study the tolerance of microalgae. The effect of CO₂ concentration, aeration rate, inoculum concentration, intermittent sparging, and nitrogen sources on the growth of A. obliquus was examined. Acutodesmus obliquus also was cultivated in a 500-L pilot outdoor tubular photobioreactor (OTP) to advance the laboratory scale system to outdoor scale-up applications. The results showed that A. obliquus could tolerate high CO₂ concentrations of 50 %, and a maximum biomass of 0.935 g L^?1 (dry weight) was achieved at 20 % CO₂. An aeration rate of 500 mL min^?1, inoculum concentration (optical density at 680 nm [OD₆₈₀]?=?0.3), and intermittent sparging of 10 min per 2 h enhanced growth to the optimum and influenced culture pH and photosynthesis. Urea as a nitrogen source was shown to be more beneficial to cell growth. A urea concentration of 0.3 g L^?1 and an N/P ratio of 15 led to maximum biomass accumulation thus enhancing the gaseous emission utilization efficiency. In conclusion, this work demonstrated that gaseous emissions containing high concentration of CO₂ from a methanol plant could be directly introduced into A. obliquus cultures and that A. obliquus was suitable well for large-scale outdoor cultivation in a tubular photobiorecator.     

The effect of temperature on growth and lipid and fatty acid composition on marine microalgae used for biodiesel production

Cultivation temperature is one of the major factors affecting the growth and lipid accumulation of microalgae. In this study, the effects of temperature on the growth, lipid content, fatty acid composition and biodiesel properties of the marine microalgae Chaetoceros sp. FIKU035, Tetraselmis suecica FIKU032 and Nannochloropsis sp. FIKU036 were investigated. These species were cultured at different temperatures (25, 30, 35 and 40 °C). The results showed that the specific growth rate, biomass and lipid content of all microalgae decreased with increasing temperature. With regards to fatty acids, the presence of saturated fatty acids (SFAs) in T. suecica FIKU032 and Nannochloropsis sp. FIKU036 decreased with increasing temperature, in contrast with polyunsaturated fatty acids (PUFAs). Moreover, Chaetoceros sp. FIKU035 was the only species that could grow at 40 °C. The highest lipid productivity was observed in Chaetoceros sp. FIKU035 when cultivated at 25 °C (66.73 ± 1.34 mg L^?1 day^?1) and 30 °C (61.35 ± 2.89 mg L^?1 day^?1). Moreover, the biodiesel properties (cetane number, cold filter plugging point, kinematic viscosity and density) of the lipids obtained from this species were in accordance with biodiesel standards. This study indicated that Chaetoceros sp. FIKU035 can be considered as a suitable species for biodiesel production in outdoor cultivation.     

Growth and photosynthetic activity of <Emphasis Type="Italic">Botryococcus braunii</Emphasis> biofilms

Botryococcus braunii is a green microalga capable of producing large amounts of external long-chain hydrocarbons suitable as a source of biofuel. There have been several studies indicating that cultures of B. braunii can reduce the energy and water requirement for mass biofuel production, especially if non-destructive extraction methods for milking hydrocarbons are used. Growing microalgae as a raw material for biofuel using conventional liquid-based cultivation (i.e., raceway ponds) has yet to be shown to be economically successful. An alternative solid growth (biofilm) cultivation method can markedly reduce the energy requirements and costs associated with the harvesting and dewatering processes. We evaluated the growth of biofilms of several strains of B. braunii (from races A, B, L and S) and found that three of the four tested races successfully grew to stationary phase in 10 weeks with no contamination. Among all races, B. braunii BOT22 (race B) reached the highest biomass and lipid yields (3.80 mg dry weight cm^?2 day^?1 and 1.11 mg dry weight cm^?2). Irrespective of the race, almost all photosynthetic parameters (F _V /F ₀ , PI_ABS and the OJIP curve) showed that the biofilm cultures were more stressed during lag and stationary phases than in logarithmic phase. We also studied the Botryococcus biofilm profiles using confocal microscopy and found that this method is suitable for estimating the overall biomass yield when compared with gravimetric measurement. In conclusion, the growth characteristics (biomass and lipid) and photosynthetic performance of all races indicated that B. braunii BOT22 is the most promising strain for biofilm cultivation.     

Phycoremediation potential,physiological, and biochemical response of <Emphasis Type="Italic">Amphora subtropica</Emphasis> and <Emphasis Type="Italic">Dunaliella</Emphasis> sp. to nickel pollution

Metal pollution can produce many biological effects on aquatic environments. The marine diatom Amphora subtropica and the green alga Dunaliella sp. possess a high metal absorption capacity. Nickel (Ni) removal by living cells of A. subtropica and Dunaliella sp. was tested in cultures exposed to different Ni concentrations (100, 200, 300, and 500 mg L^?1). The amount of Ni removed by the microalgae increased with the time of exposure and the initial Ni concentration in the medium. The metal, which was mainly removed by bioadsorption to Dunaliella sp. cell surfaces (93.63% of total Ni (for 500 mg Ni L^?1) and by bioaccumulation (80.82% of total Ni (for 300 mg Ni L^?1) into Amphora subtropica cells, also inhibited growth. Exposure to Ni drastically reduced the carbohydrate and protein concentrations and increased total lipids from 6.3 to 43.1 pg cell^?1, phenolics 0.092 to 0.257 mg GAE g^?1 (Fw), and carotenoid content, from 0.08 to 0.59 mg g^?1 (Fw), in A. subtropica. In Dunaliella sp., total lipids increased from 26.1 to 65.3 pg cell^?1, phenolics from 0.084 to 0.289 mg GAE g^?1 (Fw), and carotenoid content from 0.41 to 0.97 mg g^?1 (Fw). These compounds had an important role in protecting the algae against ROS generated by Ni. In order to cope with Ni stress shown by the increase of TBARS level, enzymatic (SOD, CAT, and GPx) ROS scavenging mechanisms were induced.     

High biomass production and CO<Subscript>2</Subscript> fixation from biogas by <Emphasis Type="Italic">Chlorella</Emphasis> and <Emphasis Type="Italic">Scenedesmus</Emphasis> microalgae using tequila vinasses as culture medium

Tequila vinasses (TVs) generated during Tequila production are brown liquid residues rich in nutrients. The nutrient content of agro-industrial effluents represents an excellent resource to support low-cost biomass production of microalgae; nonetheless, it is crucial to select the suitable microalgal strain to attain the highest biomass production in each residue used. In this study, biomass production, CO₂ fixation from biogas, and cell compound accumulation by Chlorella vulgaris U162, Chlorella sp., Scenedesmus obliquus U169, and Scenedesmus sp. using biodigested and filtered TVs as culture medium were evaluated and compared with the conventional microalgal culture media, C30, BG-11, Bold 3N, and Bristol. The four microalgae evaluated attained the highest biomass production and CO₂ fixation rate cultured in both residues, accumulating mainly carbohydrates and proteins although the most appropriate microalga to be cultured in TVs was Chlorella sp., recording 2.30 g L^?1. Moreover, the nutrient ratio of filtered TVs was ideal to support biomass production while biodigested TVs need to be supplemented with nitrogen. Overall, these results demonstrated that tequila vinasses are an excellent resource to support high and quick biomass production of microalgae, which can be used to obtain biofuels as ethanol, biogas, and supplement food depicting an extra benefit during the appropriate disposal of this residue.     

The combined effects of blue light and dilution rate on lipid class and fatty acid composition of <Emphasis Type="Italic">Tisochrysis lutea</Emphasis>

The lipid class and the fatty acid compositions of microalgae highly influence bivalve larval and post-larval development. Light is an essential environmental factor for microalgal culture, and quantity and quality of light may induce changes in the biochemical composition of the algae. The objective of this study was to investigate the effect of light spectrum (blue vs. white light) on lipid class and fatty acid compositions of Tisochrysis lutea cultured in a chemostat. Two different dilution rates (D) were assayed for each light spectrum: 0.2 and 0.7 day^?1. Triacylglycerol (TAG), sterol, and hydrocarbon (HC) content increased sharply at low D. The proportion of alkenones was significantly reduced under blue light. Polyunsaturated fatty acids (PUFA), and particularly n-3 PUFA, content in phospholipids (PL) increased under blue light compared to white light at low D. Thus, blue light raised 22:6(n-3) levels in total lipids of T. lutea at low D. The cultivation of T. lutea in a chemostat at low D under blue light may improve nutritional value as feed for bivalve larvae by modifying the PUFA profile, especially increasing 22:6(n-3).     

Screening of microalgae for primary metabolites including β-glucans and the influence of nitrate starvation and irradiance on β-glucan production

Βeta-glucans, widespread glucose polymers in mushrooms, yeasts, and bacteria, but rarely found in microalgae, have wide applications and high medicinal and economical potential. Some β-glucans like paramylon from algae-like Euglena gracilis are well investigated, but there is little information about the β-glucan content of microalgae. Therefore, more than 40 species of cultured microalgae have been investigated for composition of their biomass regarding to lipids, carbohydrates including β-glucans and proteins. Most of algae species showed a rather similar biomass composition of about 10 % lipids, 25 % carbohydrates, and 40 % proteins if they have been cultivated in a full medium, rather low light conditions of 50 μmol photons m^?2 s^?1, 12/12 h light/dark cycle under aeration and a temperature of 25?±?2 °C. The content of β-glucans varied between 1.7 and 24.2 % of dry weight, respectively. Two microalgae, Scenedesmus ovalternus SAG 52.80 and Porphyridium purpureum SAG 1380-1d with a yield of more than 20 % of dry weight were identified as the best β-glucan producers under standard cultivation conditions. Culture optimization experiments revealed that enhanced irradiance increased the β-glucan content of Scenedesmus obtusiusculus A 189, a novel green algae isolate, from 6.4 to 19.5 %, but the β-glucan content of the green alga S. ovalternus SAG 52.80 remained unaffected (24.2 vs. 23.3 %). Nitrate starvation enhanced the β-glucan content of S. obtusiusculus A 189 from 16 to 23 % and of S. ovalternus SAG 52.80 from 23.3 to 36.7 %.     

Ammonium,nitrate, and urea play different roles for lipid accumulation in the nervonic acid—producing microalgae <Emphasis Type="Italic">Mychonastes afer</Emphasis> HSO-3-1

Producing valuable coproducts from oleaginous microalgae is an option to reduce the total cost of biofuel production. Here, the influence of nitrogen sources on biomass yield and lipid accumulation of a newly identified oleaginous green microalgal strain, Mychonastes afer HSO-3-1, was evaluated. Carbon assimilation and the following lipid biosynthesis of M. afer were inhibited to some extent under weak acidic conditions (6 < pH < 7) and any of the tested nitrogen source. The highest lipid productivity of 50.7 mg L^?1 day^?1 was achieved with a 17.6 mM nitrogen supplement in the form of urea. The cell polar lipid content was significantly higher than triacylglycerol (TAG), and saturated palmitic acid (C16:0) occupied a dominant position in the fatty acid profiles while culturing M. afer in acidic medium with NH₄ ⁺ as the nitrogen source. Under neutral conditions, the lipid productivities of M. afer cultivated in media containing 17.6 mM of NaNO₃, NH₄Cl, and NH₄NO₃ were 76.2, 77.5, and 79.0 mg L^?1 day^?1, respectively. The greatest TAG content (58.56%) of total lipids was obtained when NaNO₃ was used as the nitrogen source. There was no significant difference in the fatty acid composition of M. afer cells when they were cultivated in neutral media supplemented with NaNO₃, urea, NH₄Cl, and NH₄NO₃. Therefore, NH₄ ⁺ was not a suitable nitrogen source for M. afer cultivation due to the additional labor, working procedures, and alkali required to adjust the medium pH. Considering that using urea as nitrogen source could reduce the cost of nutrient salts substantially and urea can be taken up and utilized by most microalgae, it is a preferred nitrogen source. The major properties of biodiesel derived from M. afer HSO-3-1 met biodiesel quality, and nervonic acid concentrations remained at approximately 3.0% of total fatty acids.     

Exploiting Phosphate-Starved cells of <Emphasis Type="Italic">Scenedesmus</Emphasis> sp. for the Treatment of Raw Sewage

Phosphate depletion is one of the favorable ways to enhance the sewage water treatment with the algae, however, detailed information is essential with respect to internal phosphate concentration and physiology of the algae. The growth rate of the phosphate-starved Scenedesmus cells was reduced drastically after 48 h. Indicating cells entered in the stationary phase of the growth cycle. Fourier Transform Infrared analysis of phosphate-starved Scenedesmus cells showed the reduction in internal phosphate concentration and an increase in carbohydrate/phosphate and carbohydrate/lipid ratio. The phosphate-starved Scenedesmus cells, with an initial cell density of, 1 × 10⁶ cells mL^?1 shows 87% phosphate and 100 % nitrogen removal in 24 h. The normal Scenedesmus cells need approximately 48 h to trim down the nutrients from wastewater up to this extent. Other microalgae, Ankistrodesmus, growth pattern was not affected due to phosphate starvation. The cells of Ankistrodesmus was able to reduce 71% phosphate and 73% nitrogen within 24 h, with an initial cell density of, 1 × 10⁶ cells mL^?1.     

Potential Outdoor Cultivation of Green Microalgae Based on Response to Changing Temperatures and by Combining with Air Temperature Occurrence

In this study, our working hypothesis was to examine whether temperature alters biomass and metabolite production by microalgae according to strain. We also addressed whether it is possible to choose a strain suitable for growing in each season of a given region. A factorial experiment revealed a significant interaction between chlorophylls a and b (Chl a and Chl b), carotenoid/Chl (a?+?b) ratio, biomass and total lipid productivity of six green microalgae (four Chlorella spp., Chlorella sorokiniana and Neochloris oleoabundans) after 15 days at four temperatures. At 39/35 °C, two Chlorella sp. strains (IPR7115 and IPR7117) showed higher total carotenoids/Chl (a?+?b) (0.578 and 0.830), respectively. N. oleoabundans had the highest Chl a (8210 μg L^?1) and Chl b (1909 μg L^?1) at 19/15 °C and highest maximum dry biomass (2900 mg L^?1), specific growth rate (0.538 day^?1) and total lipids (1003 mg L^?1) at 15/8 °C. We applied a method to infer the growth of these six green microalgae in outdoor ponds, as based on their response to changing temperatures and by combining with historical data on day/night air temperature occurrence for a given region. We conclude that the use of regionalized maps based on air temperature is a good strategy for predicting microalgal cultivation in outdoor ponds based on their features and tolerance to changing temperature.     

Mixotrophic cultivation of <Emphasis Type="Italic">Chlorococcum</Emphasis> sp. under non-controlled conditions using a digestate from pig manure within a biorefinery

A number of business opportunities may arise from microalgae and wastewater treatment becoming an integrated system, as biofuels and high-added value products could be obtained simultaneously. This study, performed under controlled and non-controlled conditions, aimed at cultivating Chlorococcum sp. using a digestate from pig manure as culture medium and assessing its growth and biochemical composition for further applications. Under controlled conditions, cultures of Chlorococcum sp. were established testing various digestate dilutions (v/v). It was found that all tested dilutions (up to 8% v/v) promoted a higher biomass density, compared to the control culture in modified Bold’s Basal Medium (modified BBM). Under non-controlled conditions, it was found that the biomass productivity using the digestate diluted 5.6% v/v (23.4 mg L^?1 day^?1) was statistically similar to the one obtained using modified BBM (26.4 mg L^?1 day^?1). The volatile fatty acids contained in the digestate might have allowed mixotrophic growth for Chlorococcum sp. The intracellular lipid content in Chlorococcum sp. remained constant throughout the experiments in both, treatment and control cultures, while carbohydrates increased from 20 to 45% of the cell dry weight in the treatment and from 20 to 42% in the control one. It was concluded that conditions of nitrogen starvation and fluctuating irradiance and temperature benefit carbohydrate accumulation in this strain, since intracellular carbohydrate content increased nearly two-fold during this period. Additionally, the obtained biomass has the potential to be used as feedstock for bioethanol production. This system can meet the concept of a microalgae-based biorefinery, in which biofuels and high-added value products are produced from microalgae and wastewater.     

Regulation of carbon metabolic fluxes in response to CO<Subscript>2</Subscript> supplementation in phototrophic <Emphasis Type="Italic">Chlorella vulgaris</Emphasis>: a cytomic and biochemical study

As one of the promising species of microalgae for biofuel production, Chlorella vulgaris CS-42 was cultivated phototrophically in two cylindrical photobioreactors with aeration of 5 % (v/v) CO₂ or air for 13 days to evaluate the effects of CO₂ supplementation on biomass, CO₂ fixation performance, and biochemical content. Significant increases of specific growth rate and total carbon content in biomass resulting in a higher CO₂ fixation rate were found with 5 % CO₂. The maximum biomass concentration, carbohydrate and fatty acid contents with 5 % CO₂ were significantly higher than those with air, while carbohydrate biosynthesis was most affected as compared to other biochemical components. Cytomic analysis revealed a rapid accumulation of neutral lipid in the late growth phase with more lipid bodies visualized by confocal laser scanning microscopy (CLSM), when nitrate consumption was accelerated with CO₂ supplementation. Gas chromatography mass spectrometry (GC-MS) analysis indicated that 5 % CO₂ favored the formation of C18:2, which led to a decrease in the degree of lipid unsaturation (DLU). These results proved that CO₂ supplementation was one of the most efficient methods to significantly prompt the growth of microalgae and increase the C/N ratio in the medium, which in turn regulated the carbon metabolic flux to enhance neutral lipid and fatty acid production in C. vulgaris.     

Growth and palmitoleic acid accumulation of filamentous oleaginous microalgae <Emphasis Type="Italic">Tribonema minus</Emphasis> at varying temperatures and light regimes

Palmitoleic acid (C16:1Δ9), contributes greatly to human health, industrial chemicals and biodiesel. The filamentous oleaginous microalgae Tribonema sp. has been identified as a highly efficient producer of palmitoleic acid. Temperature and light regime were adapted to regulate the palmitoleic acid content in this study. Strain T. minus was able to grow well at all the tested temperatures, even at 5 °C. The optimum temperature for palmitoleic acid accumulation (54.25 % of total fatty acid) was 25 °C. Moreover, both light intensity and photoperiod affect the growth, lipid content and fatty acid files of T. minus. The culture exposed to 240 μmol photons m^?2 s^?1 with a photoperiod of 24:0 showed the highest biomass (6.87 g L^?1) and biggest lipid content (61.27 % of dry weight), whereas the most amount of palmitoleic acid (50.47 % of total fatty acid) was detected at 120 μmol photons m^?2 s^?1. These findings make tangible contributions to culture T. minus for commercial production of lipid or palmitoleic acid.     

Effect of microalgae hydrolysate foliar application (<Emphasis Type="Italic">Arthrospira platensis</Emphasis> and <Emphasis Type="Italic">Scenedesmus</Emphasis> sp.) on <Emphasis Type="Italic">Petunia x hybrida</Emphasis> growth

In horticultural practice accelerated plant development and particularly earlier flowering, has been reported with microalgae applications. Therefore, the objective of this work was to study the effects of foliar spraying with Scenedesmus sp. and Arthrospira platensis hydrolysates on Petunia x hybrida plant development and leaf nutrient status. Three treatments were tested: T1 (foliar application with water, the control), T2 (foliar application with Arthrospira), and T3 (foliar application with Scenedesmus). Foliar spraying was applied five times (0, 14, 28, 35, and 42 days after transplanting). The concentration of both microalgae was 10 g L^?1. At the end of the trial biometric parameters and nutrient concentration in photosynthetic organs (the leaves) were measured. The results of this assay show that foliar application of Scenedesmus accelerated plant development in terms of higher rates of root growth, leaf and shoot development, and earliness of flowering. Arthrospira enhanced the root dry matter, the number of flowers per plant, and the water content. Nevertheless, a reduction was found in the conductive tissue (stem + petiole) dry weight with Arthrospira compared with Scenedesmus and the control. The results also show that microalgae hydrolysate supply can improve the plant nutrient status. Based on these results, it is advisable to use Scenedesmus hydrolysates in foliar applications to increase the blooming of Petunia x hybrida.     

Changes in growth and composition of the marine microalgae <Emphasis Type="Italic">Phaeodactylum tricornutum</Emphasis> and <Emphasis Type="Italic">Nannochloropsis salina</Emphasis> in response to changing sodium bicarbonate concentrations

Oils, carbohydrates, and fats generated by microalgae are being refined in an effort to produce biofuels. The research presented here examines two marine microalgae, Nannochloropsis salina (green alga) and Phaeodactylum tricornutum (diatom), when grown with 0 (no addition), 0.5, 1.0, 2.0, and 5.0 g L^?1 NaHCO₃ added to an f/2 medium during the growth phase (GP) and a nutrient induced (nitrate limitation) lipid formation phase (LP). We hypothesize that the addition of NaHCO₃ is a sustainable and practical strategy to increase cellular density and concentrations of lipids in microalgae as well as the rate of lipid accumulation. In N. salina, final cell densities were significantly (p?<?0.05) higher in the NaHCO₃-treated cells than the control while in P. tricornutum the cell densities were higher with >[NaHCO₃] during the GP. During the LP, cell densities were generally higher in the NaHCO₃-treated cells compared with controls. F _V/F _M (efficiency of photosystem II) patterns paralleled those for cell density with generally higher values with higher concentrations of NaHCO₃ and significantly different values between controls and 5.0 g L^?1 NaHCO₃ at the end of the GP (p?<?0.05). F _V/F _M was variable between treatments in P. tricornutum (0.3–0.65) but less so in N. salina for (0.5–0.7) regardless of [NaHCO₃]. The lipid index (measured with Nile red), used as a proxy for triacylglycerides (TAGs), was 10.2?±?6.5 and 4.4?±?2.9 (fluorescence units/OD cells ×1000) for N. salina and P. tricornutum, respectively, at the end of the GP. At the end of the LP, the lipid index was eight and four times higher than during the GP in the corresponding 5.0 g L^?1 NaHCO₃ treatments, revealing that N. salina was accumulating more lipid than P. tricornutum. Dry weights essentially doubled during LP compared with GP for N. salina; this was not the case for P. tricornutum. In general, the percentage of ash in dry weights was significantly higher in the LP relative to the corresponding GP treatments for P. tricornutum; this was not the case for N. salina. During the LP, there was also less soluble protein in N. salina compared to GP; differences were not significant in cells growing with 2.0 or 5.0 g L^?1 NaHCO₃. In P. tricornutum, faster growing cells had more soluble protein during the GP and LP; differences between treatments were significant. P. tricornutum generally accumulated significantly more crude protein than N. salina at higher [NaHCO₃]; there was three times more crude protein in the highest NaHCO₃ (5.0 g L^?1) treatment compared with the controls. C:N ratios (mol:mol) were similar across treatments during GP: 7.03?±?0.12 and 10.16?±?0.41 for N. salina and P. tricornutum, respectively. Further, C:N ratios increased with increasing [NaHCO₃] during LP. Species-specific fatty acid methyl ester (FAMEs) profiles were observed. While C16:0 was lower in P. tricornutum compared to N. salina, the diatom produced more C16:1 and C14 but not C18:3. Monounsaturated fatty acids (MUFA) significantly increased in N. salina in the LP compared to GP and in response to increasing [NaHCO₃] (t tests; p?<?0.05). Saturated fatty acids (SFA) responded similarly but to a lesser degree. There were more polyunsaturated fatty acids (PUFA) in N. salina than MUFAs or SFAs. In P. tricornutum, there were generally more SFAs, MUFAs and PUFAs in P. tricornutum during LP than GP in the corresponding NaHCO₃ treatments. These findings reveal the importance of considering NaHCO₃ as a supplemental carbon source in the culturing marine phytoplankton in large-scale production for biofuels.