Continuous propionate production from whey permeate using a novel fibrous bed bioreactor

Continuous production of propionate from whey lactose by Propionibacterium acidipropionici immobilized in a novel fibrous bed bioreactor was studied. In conventional batch propionic acid fermentation, whey permeate without nutrient supplementation was unable to support cell growth and failed to give satisfactory fermentation results for over 7 days. However, with the fibrous bed bioreactor, a high fermentation rate and high conversion were obtained with plain whey permeate and de-lactose whey permeate. About 2% (wt/vol) propionic acid was obtained from a 4.2% lactose feed at a retention time of 35 to 45 h. The propionic acid yield was approximately 46% (wt/vol) from lactose. The optimal pH for fementation was 6.5, and lower fermentation rates and yields were obtained at lower pH values. The optimal temperature was 30 degrees C, but the temperature effect was not dramatic in the range of 25 to 35 degrees C. Addition of yeast extract and trypticase to whey permeate hastened reactor startup and increased the fermentation rate and product yields, but the addition was not required for long-term reactor performance. The improved fermentation results with the immobilized cell bioreactor can be attributed to the high cell density, approximately 50 g/L, attained in the bioreactor, Cells were immobilized by loose attachement to fiber surfaces and entrapment in the void spaces within the fibrous matrix, thus allowing constant renewal of cells. Consequently, this bioreactor was able to operate continuously for 6 months without encountering any clogging, degeneration, or contamination problems. Compared to conventional batch fermentors, the new bioreactor offers many advantages for industrial fermentation, including a more than 10-fold increase in productivity, acceptance of low-nutrient feedstocks such as whey permeate, and resistance to contamination. (c) 1994 John Wiley & Sons, Inc.     

Optimal conditions for production of lactic acid from cheese whey permeate by Ca-alginate-entrapped Lactobacillus helveticus

Whole cells of Lactobacillus helveticus were immobilized in calcium-alginate beads to produce lactic acid from cheese whey ultrafiltrate. Ca-alginate-entrapped cells were characterized by higher fermentation rates and optimum pH than free cells. No difference could be observed in the profile of cell activity against temperature for either type of cells. After a heat treatment, cell activity was higher for free cells than for immobilized cells. Continuous lactic acid fermentation using a packed bed reactor was investigated.     

Production of propionic acid from whey permeate by sequential fermentation, ultrafiltration, and cell recycling

This article deals with the production by fermentation of a mycostatic and aromatic food additive based on propionic acid. Membrane bioreactors have been used from laboratory scale up to pilot and industrial production plants. Due to the high cell densities achieved by the sequential recycling mode of operation, a mixed acids solution was rapidly produced from whey permeate. The sterile fermented broth obtained was subsequently concentrated at different levels by evaporation and spray drying according to the projected use. Concentrated Propionibacterium cells (200 g . L(-1) DW) were obtained from the process by periodic bleeds and could be used to good effect as cheese starters, silage preservatives, or probiotics. Propionic acid concentrations from 30 to 40 g . L(-1) were easily achieved with no residual lactose. The highest volumetric productivity was 1.6 g . L(-1) . h(-1) for total acid and 1.2 g . L(-1) . h(-1) for propionic acid with a specific productivity of 0.035 h(-1). (c) 1993 John Wiley & Sons, Inc.     

Batch propagation of Lactobacillus helveticus for production of lactic acid from lactose concentrated cheese whey with microaeration and nutrient supplementation

Continuous mix batch bioreactors were used to study the kinetic parameters of lactic acid fermentation in microaerated-nutrient supplemented, lactose concentrated cheese whey using Lactobacillus helveticus. Four initial lactose concentrations ranging from 50 to 150 g l^–1 were first used with no microaeration and no yeast extract added to establish the substrate concentration above which inhibition will occur and then the effects of microaeration and yeast extract on the process kinetic parameters were investigated. The experiments were conducted under controlled pH (5.5) and temperature (42 °C) conditions. The results indicated that higher concentrations of lactose had an inhibitory effect as they increased the lag period and the fermentation time; and decreased the specific growth rate, the maximum cell number, the lactose utilization rate, and the lactic acid production rate. The maximum lactic acid conversion efficiency (75.8%) was achieved with the 75 g l^–1 initial lactose concentration. The optimum lactose concentration for lactic acid production was 75 g l^–1 although Lactobacillus helveticus appeared to tolerate up to 100 g l^–1 lactose concentration. Since the lactic acid productivity is of a minor importance compared to lactic acid concentration when considering the economic feasibility of lactic acid production from cheese whey using Lactobacillus helveticus, a lactose concentration of up to 100 g l^–1 is recommended. Using yeast extract and/or microaeration increased the cell number, specific growth rate, cell yield, lactose consumption, lactic acid utilization rate, lactic acid concentration and lactic acid yield; and reduced the lag period, fermentation time and residual lactose. Combined yeast extract and microaeration produced better results than each one alone. From the results it appears that the energy uncoupling of anabolism and catabolism is the major bottleneck of the process. Besides lactic acid production, lactose may also be hydrolysed into glucose and galactose. The -galactosidase activity in the medium is caused by cell lysis during the exponential growth phase. The metabolic activities of Lactobacillus helveticus in the presence of these three sugars need further investigation.     

Effect of initial bacteria concentration on hydrogen gas production from cheese whey powder solution by thermophilic dark fermentation

Dark fermentative hydrogen gas production from cheese whey powder solution was realized at 55°C. Experiments were performed at different initial biomass concentrations varying between 0.48 and 2.86 g L^?1 with a constant initial substrate concentration of 26 ± 2 g total sugar (TS) per liter. The highest cumulative hydrogen evolution (633 mL, 30°C), hydrogen yield (1.56 mol H₂ mol^?1 glucose), and H₂ formation rate (3.45 mL h^?1) were obtained with 1.92 g L^?1 biomass concentration. The specific H₂ production rate decreased with increasing biomasss concentration from the highest value (47.7 mL g^?1 h^?1) at 0.48 g L^?1 biomass concentration. Total volatile fatty acid concentration varied beetween 10 and 14 g L^?1 with the highest level of 14.2 g L^?1 at biomass concentration of 0.48 g L^?1 and initial TS content of 28.4 g L^?1. The experimental data were correlated with the Gompertz equation and the constants were determined. The most suitable initial biomass to substrate ratio yielding the highest H₂ yield and formation rate was 0.082 g biomass per gram of TS. © 2012 American Institute of Chemical Engineers Biotechnol. Prog., 28: 931–936, 2012     

A novel recycle batch immobilized cell bioreactor for propionate production from whey lactose

Recycle batch fermentations using immobilized cells of Propionibacterium acidipropionici were studied for propionate production from whey permeate, de-lactose whey permeate, and acid whey. Cells were immobilized in a spirally wound fibrous sheet packed in a 0.5-L column reactor, which was connected to a 5-L stirred tank batch fermentor with recirculation. The immobilized cells bioreactor served as a breeder for these recycle batch fermentations. High fermentation rates and conversions were obtained with these whey media without nutrient supplementation. It took approximately 55 h to ferment whey permeate containing approximately 45 g/L lactose to approximately 20 g/L propionic acid. Higher propionate concentrations can be produced with various concentrated whey media containing more lactose. The highest propionic acid concentration obtained with the recycle batch reactor was 65 g/L, which is much higher than the normal maximum concentration of 35 to 45 g/L reported in the literature. The volumetric productivity ranged from 0.22 g/L . h to 0.47 g/L . h, depending on the propionate concentration and whey medium used. The corresponding specific cell productivity was 0.033 to 0.07 g/L . g cell. The productivity increased to 0.68 g/L . h when whey permeate was supplemented with 1% (w/v) yeast extract. Compared with conventional batch fermentation, the recycle batch fermentation with the immobilized cell bioreactor allows faster fermentation, produces a higher concentration of product, and can be run continually without significant downtime. The process also produced similar fermentation results with nonsterile whey media. (c) 1995 John Wiley & Sons, Inc.     

Continuous propionic acid fermentation by immobilized Propionibacterium acidipropionici in a novel packed-bed bioreactor

Continuous propionic acid fermentations of lactate by Propionibacterium acidipropionici were studied in spiral wound fibrous bed bioreactors. Cells were imobilized by natural attachment to fiber surfaces and entrapment in the void volume within the fibrous matrix. A high cell density of approximately 37 g/L was attained in the reactor and the reactor productivity was approximately 4 times higher than that from a conventional batch fermentation. The bioreactor was able to operate continuously for 4 months without encountering any clogging, degeneration, or contamination problems. Also, the reactor could accept low-nutrient and low-pH feed without sacrificing much in reactor productivity. This new type of immobilized cell bioreactor is scalable and thus is suitable for industrial production of propionate. (c) 1992 John Wiley & Sons, Inc.     

Lactic acid production from whey permeate by immobilized Lactobacillus casei

Two matrices have been assessed for their ability to immobilize Lactobacillus casei cells for lactic acid fermentation in whey permeate medium. Agar at 2% concentration was found to be a better gel than polyacrylamide in its effectiveness to entrap the bacterial cells to carry out batch fermentation up to three repeat runs. Of the various physiological parameters studied, temperature and pH were observed to have no significant influence on the fermentation ability of the immobilized organism. A temperature range of 40–50°C and a pH range of 4.5–6.0 rather than specific values, were found to be optimum when fermentation was carried out under stationary conditions. In batch fermentation ～90% conversion of the substrate (lactose) was achieved in 48 h using immobilized cell gel cubes of 4 × 2 × 2 mm size, containing 400 mg dry bacterial cells per flask and 4.5% w/v (initial) whey lactose content as substrate. However, further increase in substrate levels tested (>4.5% w/v) did not improve the process efficiency. Supplementation of Mg²⁺ (1 mM) and agricultural by-products (mustard oil cake, 6%) in the whey permeate medium further improved the acid production ability of the immobilized cells under study.     

Influence of initial pH on hydrogen production from cheese whey

Batch experiments were conducted to investigate the effect of initial pH, between 5 and 10, on fermentative hydrogen production from crude cheese whey (87.5% (v/v) by Clostridium saccharoperbutylacetonicum). Hydrogen was produced over the range of pH studied. The hydrogen production rate and yield peaked at an initial pH 6 and then steadily decreased as the pH increased. The highest rate and yield were 28.3 ml h⁻¹ and 7.89 mmol g⁻¹ lactose, respectively. Sugar consumption was unaffected between pH 5 and 9 and remained at 97%. All final pHs were acidic and increased alongside the initial pH. There was no correlation between the initial pH and the fermentation time; the times were shorter (50–52 h) between pH 6 and 8, and longer (62–82 h) outside this range. A modified Gompertz equation adequately described fermentative hydrogen production from cheese whey. The respective maximum hydrogen production rate and hydrogen potential at an optimal pH of 6 were 47.07 ml h⁻¹ and 1432 ml. Lag phase times were much longer at acidic pHs than at alkaline pHs.     

Continuous stable production of von Willebrand Factor monoclonal antibody in spin filter bioreactor with bleeding technology

The characteristics of two different modes of perfusion culture, intermittent and continuous bleedings, were investigated by culturing the hybridoma cells producing von Willebrand Factor (vWF) monoclonal antibody (McAb) in a 15 L bioreactor without clogging the filter. Both culture methods exhibited similar profiles of cell density and metabolite concentrations during the culture period at the cell concentration of around 1×10⁷ cells/mL. When the perfusion rate was increased, the intermittent bleeding culture showed problems of ammonia accumulation and decrease of cell viability. The continuous bleeding culture exhibited higher physiological activity than that of the intermittent bleeding culture in terms of nutrient consumption and metabolite production kinetics. But the analysis of specific oxygen consumption rate showed that the specific oxygen consumption rate of intermittent bleeding culture was similar to that of exponential growth phase. The continuous bleeding culture showed higher specific vWF McAb productivity and cumulative production than those of the intermittent bleeding culture. Finally we proved the possibility of long-term operation of continuous bleeding culture and produced approximately 40 g of vWF McAb in a 15 L bioreactor after one-month operation.     

Continuous production of lactic acid from whey permeate by Lactobacillus helveticus in two chemostats in series

The effect of dilution rate on the production of lactic acid from whey permeate by Lactobacillus helveticus has been investigated. In the first chemostat of a two-stage system, total conversion (98.1%) and maximum lactic acid concentration (43.7 g l⁻¹) were obtained at a dilution rate (D_Itot) of 0.06 h⁻¹. Maximum volumetric productivities of lactic acid (8.27 g l⁻¹ h⁻¹) and biomass (1.90 g l⁻¹ h⁻¹) occurred at D_Itot of 0.40 h⁻¹. The fraction of -lactate in the product was found to increase with dilution rate and reached a maximum of 66% at the same dilution rate. The maximum specific growth rate (μ_max) on this medium was 0.7 h⁻¹. A Y_ATP (max) value of 22.4 g dry weight (mol ATP)⁻¹ and a maintenance coefficient of 8.0 mmol ATP (g dry weight h)⁻¹ were determined. The second stage, in series with the first, confirmed these results and further showed that the total residence time could be reduced by 50%, compared with a single chemostat for the same nearly complete level of substrate conversion.     

Anaerobic fermentative production of lactic acid using cheese whey and corn steep liquor

Cheese whey was the most suitable substrate for production of lactic acid under anaerobic conditions by Entercoccus flavescens which, on supplementating with corn steep liquor (5% v/v) and 10 mM CaCO₃ at pH 5.5, 37°C, yielded 12.6 g lactic acid/l in 36 h. Production was scaled up to a 10 l bioreactor under controlled pH and continuous CO₂ supply and gave 28 g lactic acid/l in 30 h resulting in a net 8.7-fold increase in production as compared to unoptimized conditions.     

Efficient co‐production of propionic acid and succinic acid by Propionibacterium acidipropionici using membrane separation coupled technology

To improve the fermentation efficiency of Propionibacterium acidipropionici, a semi‐continuous coupled fermentation process was established to achieve co‐production of propionic acid (PA) and succinic acid (SA). First, the optimal proportion of glucose (Glc) and glycerol (Gl) as a mixed carbon source was determined, and the feeding procedure of Gl was optimized to make more energy flow in the direction of product synthesis. Then, ZGD630 anion exchange resin was used for efficient adsorption of PA, thereby eliminating the feedback inhibition effect of PA. Finally, an efficient, coupled fermentation process of P. acidipropionici characterized by membrane separation and chromatography technology was developed. The concentrations of PA and SA reached 62.22 ± 2.32 and 20.45 ± 1.34 g L⁻¹, with corresponding productivity of 0.43 and 0.14 g L⁻¹ h⁻¹, increased by 65.38% and 48.54%, respectively. Membrane separation coupled fermentation of PA and SA could significantly improve the process economics of P. acidipropionici, and has good prospects for industrial application.     

Production of butyric acid by batch fermentation of cheese whey withClostridium beijerinckii

Summary The effect of pH on the fermentation of butyric acid byClostridium beijerinckii using cheese whey as a substrate was studied. Maximum concentrations of the acid were produced when the pH was controlled at 5.5. Raising or lowering of pH was found to reduce the total acid formation. This particular strain ofC. beijerinckii produced insignificant amounts of butanol in all the pure culture cases investigated. A comparative study of the fermentation in a synthetic glucose medium and in cheese whey showed the whey to produce more butyric acid.     

Simultaneous production of propionic acid and vitamin B12 from corn stalk hydrolysates by Propionibacterium freudenreichii in an expanded bed adsorption bioreactor

Abstract

Vitamin B12 and propionic acid that were simultaneous produced by Propionibacterium freudenreichii are both favorable chemicals widely used in food preservatives, medicine, and nutrition. While the carbon source and propionic acid accumulation reflected fermentation efficiency. In this study, using corn stalk as a carbon source and fed-batch fermentation process in an expanded bed adsorption bioreactor was studied for efficient and economic biosynthesis of acid vitamin B12 and propionic. With liquid hot water pretreated corn stalk hydrolysates as carbon source, 28.65?mg L^?1 of vitamin B12 and 17.05?g L^?1 of propionic acid were attained at 168?h in batch fermentation. In order to optimize the fermentation outcomes, fed-batch fermentation was performed with hydrolyzed corn stalk in expanded bed adsorption bioreactor (EBAB), giving 47.6?mg L^?1 vitamin B12 and 91.4?g L^?1 of propionic acid at 258?h, which correspond to product yields of 0.37?mg g^?1 and 0.75?g g^?1, respectively. The present study provided a promising strategy for economically sustainable production of vitamin B12 and propionic acid by P. freudenreichii fermentation using biomass cornstalk as carbon source and expanded bed adsorption bioreactor.     

Optimization of propionic acid production in apple pomace extract with Propionibacterium freudenreichii

Abstract

Sequential optimization of propionate production using apple pomace was studied. All experiments were performed in a static flask in anaerobic conditions. Effect of apple pomace as nitrogen source against conventional N sources (yeast extract, peptone) was studied. The double increase was observed in propionic acid production while using yeast extract and peptone (0.29?±?0.01?g/g), as against the use of only apple pomace extract (APE) (0.14?±?0.01?g/g). Intensification of propionic acid fermentation was also achieved by increasing the pH control frequency of the culture medium from 24-(0.29?±?0.01?g/g) to 12-hour intervals (30?°C) (0.30?±?0.02?g/g) and by increasing the temperature of the culture from 30 to 37?°C (12-hour intervals of pH control) (0.32?±?0.01?g/g). An important factor in improving the parameters of fermentation was the addition of biotin to the medium. The 0.2?mg/L dose of biotin allowed to attain 7.66?g/L propionate with a yield of 0.38?±?0.03?g/g (12-hour intervals of pH control, 37?°C).     

Enhanced propionic acid fermentation by Propionibacterium acidipropionici mutant obtained by adaptation in a fibrous-bed bioreactor

Fed-batch fermentations of glucose by P. acidipropionici ATCC 4875 in free-cell suspension culture and immobilized in a fibrous-bed bioreactor (FBB) were studied. The latter produced a much higher propionic acid concentration (71.8 +/- 0.8 g/L vs. 52.2 +/- 1.1 g/L), indicating enhanced tolerance to propionic acid inhibition by cells adapted in the FBB. Compared to the free-cell fermentation, the FBB culture produced 20-59% more propionate (0.40-0.65 +/- 0.02 g/g vs. 0.41 +/- 0.02 g/g), 17% less acetate (0.10 +/- 0.01 g/g vs. 0.12 +/- 0.02 g/g), and 50% less succinate (0.09 +/- 0.02 g/g vs. 0.18 +/- 0.03 g/g) from glucose. The higher propionate production in the FBB was attributed to mutations in two key enzymes, oxaloacetate transcarboxylase and propionyl CoA: succinyl CoA transferase, leading to the production of propionic acid from pyruvate. Both showed higher specific activity and lower sensitivity to propionic acid inhibition in the mutant than in the wild type. In contrast, the activity of PEP carboxylase, which converts PEP directly to oxaloacetate and leads to the production of succinate from glucose, was generally lower in the mutant than in the wild type. For phosphotransacetylase and acetate kinase in the acetate formation pathway, however, there was no significant difference between the mutant and the wild type. In addition, the mutant had a striking change in its morphology. With a threefold increase in its length and approximately 24% decrease in its diameter, the mutant cell had an approximately 10% higher specific surface area that should have made the mutant more efficient in transporting substrates and metabolites across the cell membrane. A slightly lower membrane-bound ATPase activity found in the mutant also indicated that the mutant might have a more efficient proton pump to allow it to better tolerate propionic acid. In addition, the mutant had more longer-chain saturated fatty acids (C17:0) and less unsaturated fatty acids (C18:1), both of which could decrease membrane fluidity and might have contributed to the increased propionate tolerance. The enhanced propionic acid production from glucose by P. acidipropionici was thus attributed to both a high viable cell density maintained in the reactor and favorable mutations resulted from adaptation by cell immobilization in the FBB.     

Engineering Propionibacterium acidipropionici for enhanced propionic acid tolerance and fermentation

Propionibacterium acidipropionici, a Gram‐positive, anaerobic bacterium, has been the most used species for propionic acid production from sugars. In this study, the metabolically engineered mutant ACK‐Tet, which has its acetate kinase gene knocked out from the chromosome, was immobilized and adapted in a fibrous bed bioreactor (FBB) to increase its acid tolerance and ability to produce propionic acid at a high final concentration in fed‐batch fermentation. After about 3 months adaptation in the FBB, the propionic acid concentration in the fermentation broth reached ～100 g/L, which was much higher than the highest concentration of ～71 g/L previously attained with the wild‐type in the FBB. To understand the mechanism and factors contributing to the enhanced acid tolerance, adapted mutant cells were harvested from the FBB and characterized for their morphology, growth inhibition by propionic acid, protein expression profiles as observed in SDS–PAGE, and H⁺‐ATPase activity, which is related to the proton pumping and cell's ability to control its intracellular pH gradient. The adapted mutant obtained from the FBB showed significantly reduced growth sensitivity to propionic acid inhibition, increased H⁺‐ATPase expression and activity, and significantly elongated rod morphology. Biotechnol. Bioeng. 2009; 104: 766–773 © 2009 Wiley Periodicals, Inc.     

Recovery of the proteose peptone component 3 from cheese whey in Reppal PES 100/polyethylene glycol aqueous two-phase systems

Recovery of the proteose peptone component 3 from cheese whey was optimal using a 16% (w/w) Reppal PES 100 – 24% (w/w) PEG 600 aqueous two-phase system, at pH 7, giving a mass recovery yield of 99% and a purity of 83% for proteose peptone component 3 in the upper phase. Using the above system a partition coefficient of 30.7 and a purification factor of 6.9 were achieved.