木质素生物降解与纸浆工业废水脱色

主要工业废水之一的纸浆工业废水中的木质素类有色物质的去除一直倍受关注。本文主要综述了木质素降解微生物、影响木质素降解的因素、木质素降解酶类及其基因工程研究和纸浆工业废水的固定化真菌法和酶法脱色。     

Bioremediation of pulp and paper mill effluent by a novel fungal consortium isolated from polluted soil

Two basidiomycetous fungi (Merulius aureus syn. Phlebia sp. and an unidentified genus) and a deuteromycetous fungus (Fusarium sambucinum Fuckel MTCC 3788) were isolated from soils affected with effluents of a pulp and paper mill over several years. These isolates were immobilized on nylon mesh and the consortium was used for bioremediation of pulp and paper mill effluent in a continuously aerated bench-top bioreactor. The treatment resulted in the reduction of color, lignin and COD of the effluent in the order of 78.6%, 79.0% and 89.4% in 4 days. A major part of reductions in these parameters occurred within first 24h of the treatment, which was also characterized by a steep decline in the pH of the effluent. During this period, total dissolved solids, electrical conductivity and salinity of the effluent also registered marked decline. It is pertinent to note that this is the first report of bioremediation of pulp and paper mill effluent by an immobilized fungal consortium.     

Decolorization of Kraft effluent by free and immobilized lignin peroxidases and horseradish peroxidase

Color removal from Kraft effluent by lignin peroxidase and horseradish peroxidase was compared. Free lignin peroxidase and horseradish peroxidase removed color from kraft effluent. Immobilization of lignin peroxidase type III, lyophilized fungal culture and horseradish peroxidase on CNBr-Sepharose 4B improved the decolorization by factor of 2.9, 4.5 and 2.6, respectively in 48 h. Lignin peroxidase type I was effective only in the immobilized form in decolorization. In general, the immobilized form all the studied systems exhibited an average value around of 30% polymer consumption and very little of depolymerization. Lignin peroxidases and lyophilized fungal culture were shown to have considerable potential for treating Kraft effluents.     

Isolation and characterization of alkalotolerant bacteria and optimization of process parameters for decolorization and detoxification of pulp and paper mill effluent by Taguchi approach

Four different bacterial strains were isolated from pulp and paper mill sludge in which one alkalotolerant isolate (LP1) having higher capability to remove color and lignin, was identified as Bacillus sp. by 16S RNA sequencing. Optimization of process parameters for decolorization was initially performed to select growth factors which were further substantiated by Taguchi approach in which seven factors, % carbon, % black liquor, duration, pH, temperature, stirring and inoculum size, at two levels, applying L-8 orthogonal array were taken. Maximum color was removed at pH 8, temperature 35°C, stirring 200 rpm, sucrose (2.5%), 48 h, 5% (w/v) inoculum size and 10% black liquor. After optimization 2-fold increase in color and lignin removal from 25–69% and 28–53%, respectively, indicated significance of Taguchi approach in decolorization and delignification of lignin in pulp and paper mill effluent. Enzymes involved in the process of decolorization of effluent were found to be xylanase (54 U/ml) and manganese peroxidase (28 U/ml). Treated effluent was also evaluated for toxicity by Comet assay using Saccharomyces cerevisiae MTCC 36 as model organism, which indicated 58% reduction after treatment by bacterium.     

Biotreatment of pulp mill bleachery effluents with the coelomycetous fungusStagonospora gigaspora

Summary The coelomyceteStagonospora gigaspora degrades lignin derivatives within pulp mill bleachery effluents. Besides dechlorination, 90% of the color was removed from CEH bleachery effluents. Lignin derivatives in the effluents of the EOP bleaching stages revealed more persistent against fungal attack. Toxicity of both effluents was diminished significantly byS. gigaspora.     

Biological degradation of resin acids in wood chips by wood-inhabiting fungi.

Resin acids in many pulp mill effluents are primary sources of toxicity to fish. Inconsistent biological detoxification of chlorinated and nonchlorinated resin acids in secondary treatment of pulp mill effluents is a continuing source of concern. An alternative approach to effluent detoxification is to remove or modify the toxic compounds present in wood chips prior to pulping. Results from experiments in which lodgepole pine sapwood chips were inoculated with several fungal candidates indicate that the total resin acid content can be reduced by up to 67% after fungal growth. Such a treatment could be an efficient and environmentally acceptable way for deresinating wood chips and so decreasing the toxicity of pulp mill effluents.     

Four marine-derived fungi for bioremediation of raw textile mill effluents

Textile dye effluents pose environmental hazards because of color and toxicity. Bioremediation of these has been widely attempted. However, their widely differing characteristics and high salt contents have required application of different microorganisms and high dilutions. We report here decolorization and detoxification of two raw textile effluents, with extreme variations in their pH and dye composition, used at 20–90% concentrations by each of the four marine-derived fungi. Textile effluent A (TEA) contained an azo dye and had a pH of 8.9 and textile effluent B (TEB) with a pH of 2.5 contained a mixture of eight reactive dyes. The fungi isolated from mangroves and identified by 18S and ITS sequencing corresponded to two ascomycetes and two basidiomycetes. Each of these fungi decolorized TEA by 30–60% and TEB by 33–80% used at 20–90% concentrations and salinity of 15 ppt within 6 days. This was accompanied by two to threefold reduction in toxicity as measured by LC₅₀ values against Artemia larvae and 70–80% reduction in chemical oxygen demand and total phenolics. Mass spectrometric scan of effluents after fungal treatment revealed degradation of most of the components. The ascomycetes appeared to remove color primarily by adsorption, whereas laccase played a major role in decolorization by basidiomycetes. A process consisting of a combination of sorption by fungal biomass of an ascomycete and biodegradation by laccase from a basidiomycete was used in two separate steps or simultaneously for bioremediation of these two effluents.     

Potential Applications of the Oxidoreductive Enzymes in the Decolorization and Detoxification of Textile and Other Synthetic Dyes from Polluted Water: A Review

ABSTRACT

Recently, the enzymatic approach has attracted much interest in the decolorization/degradation of textile and other industrially important dyes from wastewater as an alternative strategy to conventional chemical, physical and biological treatments, which pose serious limitations. Enzymatic treatment is very useful due to the action of enzymes on pollutants even when they are present in very dilute solutions and recalcitrant to the action of various microbes participating in the degradation of dyes. The potential of the enzymes (peroxidases, manganese peroxidases, lignin peroxidases, laccases, microperoxidase-11, polyphenol oxidases, and azoreductases) has been exploited in the decolorization and degradation of dyes. Some of the recalcitrant dyes were not degraded/decolorized in the presence of such enzymes. The addition of certain redox mediators enhanced the range of substrates and efficiency of degradation of the recalcitrant compounds. Several redox mediators have been reported in the literature, but very few of them are frequently used (e.g., 1-hydroxybenzotriazole, veratryl alcohol, violuric acid, 2-methoxy-phenothiazone). Soluble enzymes cannot be exploited at the large scale due to limitations such as stability and reusability. Therefore, the use of immobilized enzymes has significant advantages over soluble enzymes. In the near future, technology based on the enzymatic treatment of dyes present in the industrial effluents/wastewater will play a vital role. Treatment of wastewater on a large scale will also be possible by using reactors containing immobilized enzymes.     

Degradation of high molecular weight compounds of Kraft pulp mill effluents by a combined treatment with fungi and bacteria

Pretreatment of Kraft pulp mill effluents by mycelial pellets or extracellular ligninolytic liquid from Phanerochaete chrysosporium enhanced the anaerobic degradation of high molecular weight (HMW) compounds up to 79% and 72% respectively, against 45% when only anaerobic digestion was considered. Decolourization was obtained only after fungal pretreatment, since both anaerobic digestion and ligninolytic liquid pretreatment of Kraft effluent slightly increased colour.     

Bioremediation of paper and pulp mill effluents

Pulp and paper mill effluents pollute water, air and soil, causing a major threat to the environment. Several methods have been attempted by various researchers throughout the world for the removal of colour from pulp and paper mill effluents. The biological colour removal process uses several classes of microorganisms--bacteria, algae and fungi--to degrade the polymeric lignin derived chromophoric material. White rot fungi such as Phanerochaete chrysosporium, Corius versicolor, Trametes versicolor etc., are efficient in decolourizing paper and pulp mill effluents. Gliocladium virens, a saprophytic soil fungus decolourised paper and pulp mill effluents by 42% due to the production of hemicellulase, lignin peroxidase, manganese peroxidase and laccase.     

Decolorization of a kraft mill effluent with fungal mycelium immobilized in calcium alginate gel

A white-rot fungus Coriolus versicolor was immobilized by entrapment in calcium alginate beads. Treatment of a kraft mill effluent with the immobilized fungus in the presence of sucrose resulted in 80% loss of color of the effluent within 3 days. The minimal concentration of sucrose required for the decolorization was 10 mM. Other carbon sources (xylose, glucose, glycerol, and ethanol) could also be used.     

A continuous biological process to decolorize bleach plant effluents

Although almost every U.S. pulp mill has a biological wastewater treatment system, these systems based on bacteria, are largely ineffective in the removal of color. For this reason, we have attempted to utilize Phanerochaete chrysosporium, a fungus known to degrade lignin, as the primary organism in a novel waste treatment scheme named the MyCoR Process. Color from bleached Kraft mills originates principally from the first extraction stage of the bleach plant. It is this waste stream which is sent to the MyCoR Process reactor, a rotating biological contactor, for decolorization. We have found that under optimal conditions up to 2,000 color units/L/day can be removed from the waste stream. There is also a concomitant removal of COD and BOD. In addition, chlorolignins originating from the bleaching process were found to be dechlorinated; this is of interest to those concerned with the impact of bleach plant effluents on the environment. The process uses conventional wastewater treatment equipment. However, the use of a pure culture of fungus in a secondary metabolic state has not been attempted previously in a waste treatment scheme. Minor equipment modification and close operator attention may therefore be required. A preliminary economic analysis shows that the MyCoR Process, in its present state, would cost about US$30/metric ton of bleached Kraft pulp produced. This cost will decrease as improved or new strains of fungi are developed for the process.     

A novel hybrid technology for remediation of molasses-based raw effluents

A novel three-step technology for treatment of four molasses-based raw industrial effluents, varying in their COD, color and turbidity is reported here. Sequential steps involved in this treatment are; (1) sonication of the effluents, (2) whole-fungal treatment of these by a ligninolytic marine fungus and (3) biosorption of the residual color with heat-inactivated biomass of the same fungus. Sonication reduced the foul odor and turbidity of the effluents. It increased biodegradability of the effluents in the second stage of treatment. Laccase production in the presence of all the four effluents was directly correlated with their decolorization. After the third step, a reduction of 60-80% in color, 50-70% in COD and 60-70% in total phenolics were achieved. Comparative mass and nuclear magnetic resonance spectra indicated increasing degradation of the effluent components after each stage. Toxicity (LC₅₀ values) against Artemia larvae was reduced by two to five folds.     

Decolorization of phenolic effluents by soluble and immobilized phenol oxidases

Summary Colour removal from phenplic industrial effluents by phenol oxidase enzymes and white-rot fungi was compared. Soluble laccase and horseradish peroxidase (HRP) removed colour from pulp mill (E), cotton mill hydroxide (OH) and cotton mill sulphide (S) effluents, but rapid and irreversible enzyme inactivation took place. Entrapment of laccase in alginate beads improved decolorization by factors of 3.5 (OH) and 2 (E); entrapment of HRP improved decolorization by 36 (OH), 20 (E) and 9 (S). Beads were unsuitable for continuous use because the enzymes were rapidly released into solution. Co-polymerization of laccase or HRP with L-tyrosine gave insoluble polymers with enzyme activity. Entrapment of the co-polymers in gel beads further increased the efficiency of decolorization of E by 28 (laccase) and by 132 (HRP) compared with soluble enzymes. Maximum decolorization of all three effluents by batch cultures of Coriolus versicolor (70%–80% in 8 days) was greater than the maximum enzymic decolorization (48% of OH in 3 days by entrapped laccase). Soluble laccase (222 units ml^–1) precipitated 1.2 g l^–1 phenol from artificial coal conversion effluent at pH 6.0 and the rate of precipitation and enzyme inactivation was faster at pH 6.0 than at pH 8.5.Offprint requests to: R. G. Burns     

Enhanced production of ligninolytic enzymes and decolorization of molasses distillery wastewater by fungi under solid state fermentation

Selected isolates of fungi were grown on wheat straw and corncob in the presence of different moistening agents such as water, molasses, potato dextrose broth and distillery effluent. All the fungal isolates responded differently with respect to growth and ligninolytic enzyme production. Fungal growth on different substrates was checked by calculating ergosterol content, which varied widely within a single species when grown on different substrates. The maximum laccase production was obtained for Aspergillus flavus TERI DB9 grown on wheat straw with molasses. For manganese peroxidase, highest production was in Aspergillus niger TERI DB20 grown on corncob with effluent. Among the two isolates positive for lignin peroxidase, the highest production was in Fusarium verticillioides ITCC 6140. This immobilized fungal biomass was then used for decolorization of effluent from a cane molasses based distillery. Maximum decolorization (86.33%) was achieved in Pleurotus ostreatus (Florida) Eger EM 1303 immobilized on corncob with molasses in a period of 28 days.     

A new approach to study the decolorization of complex reactive dye bath effluent by biosorption technique

This work focused on the development of a practical biosorbent for the decolorization of textile effluents. The fermentation waste, Corynebacterium glutamicum biomass, when decarboxylated and immobilized in polysulfone matrix performed well in decolorization of simulated reactive dye bath effluent comprised of four different reactive dyes and other auxiliary chemicals. The regeneration of polysulfone-immobilized C. glutamicum was successful with the aid of 0.01 M NaOH as the eluant, which enabled the biosorbent to maintain consistent decolorization efficiency for up to 25 cycles. An up-flow packed column loaded with polysulfone-immobilized biomass performed well in the continuous treatment of Remazol effluent. Samples collected after 14 h of column operation revealed almost zero color and TOC. The column was also able to decrease the TDS level from 55,840 to 33,480 mg/L. Column regeneration experiments revealed that the biosorbent was able to continuously treat Remazol effluent over ten cycles, with more than 90.6% decolorization efficiency.     

De-colourization of textile effluent using immobilized Geotrichum candidum: an insight into mycoremediation

Textile effluent is generally complicated to manage because of its extremely noxious and recalcitrant coloured compositions. Mycoremediation is an extensively used strategy for the competent degradation of hazardous pollutants present in textile effluent. Fungus could be immobilized in synthetic or natural matrices. The current study shows the decolourization of the textile effluent by 85·5 and 98·5% within 6 h using suspended and immobilized fungus, Geotrichum candidum with optimized parameters like inoculum size (5%), pH (4·5), and temperature (30°C). To maintain a high biomass of fungal population and enhance the retention of fungal strain in the contaminated sites, the fungi need to be immobilized. Hence, the fungus was immobilized naturally onto the selected inert support that is, coconut fibres by the means of adsorption, where they grew as active films on the fibres after being grown in the culture broth. The optimized process parameters of inoculum size, fibre quantity and agitation speed for immobilized G. candidum were 5%, 2·2 g l⁻¹ of effluent and 100 rev min⁻¹ respectively. High level of laccase (22 and 25 U l⁻¹ in suspended and immobilized fungal cells treatment respectively) was observed during the process of decolourization and it was found that decolourization was directly proportional to the laccase activity. The UV–vis, FTIR, ¹H NMR and GC-MS analyses of treated textile industrial wastewater revealed the degradation of toxic pollutants in the textile effluent and formation of lower molecular weight intermediates. The study revealed a higher efficacy of immobilized G. candidum in comparison to suspended fungal culture, employing ligninolytic enzyme laccase, which catalyzes the degradation/transformation of aromatic dyes in the textile effluent thus decolourizing it.     

Biodegradation and detoxification of dyes and industrial effluents by Ganoderma weberianum B-18 immobilized in a lab-scale packed-bed bioreactor

White-rot fungi are considered to be promising biotechnological tools to complement or replace the current technologies for the treatment of effluents from textile production plants. The aim of this work was to investigate the decolorization capacity of Ganoderma weberianum B-18 in solid state fermentation with sugarcane bagasse as a substrate and ligninolytic inducer as well as to decolorize and detoxify industrial effluents by this strain in a laboratory scale packed-bed bio-reactor. The results demonstrated that G. weberianum B-18 indeed showed to possess decolorization capacity in solid state fermentation with sugarcane bagasse supplemented with synthetic dyes. Moreover, fungal biomass of G. weberianum B-18 immobilized in sugarcane bagasse in a packed-bed bioreactor was shown to efficiently decolorize and detoxify different dyes and authentic industrial effluents in semi-continuous conditions. In this decolorization process, laccase enzymes secreted by the fungus played the main role. Hence, a packed-bed reactor with G. weberianum B-18 immobilized in sugarcane bagasse seems to be a suitable system for the further development of an efficient bioprocess for large-scale treatment of dye-containing wastewaters.     

Decolorization of practical textile industry effluents by white rot fungus Coriolus versicolor IBL-04

Textile industry discharges a vast amount of unused synthetic dyes in effluents. The discharge of these effluents into rivers and lakes leads to a reduction in sunlight penetration in natural water bodies, which, in turn, decreases both photosynthetic activity and dissolved oxygen concentration rendering it toxic to living beings. This paper describes the decolorization potential of a local white rot fungus, Coriolus versicolor IBL-04 for practical industrial effluents collected from five different textile industries of Faisalabad, Pakistan. Screening of C. versicolor IBL-04 on five effluents showed best decolorization results (36.3%) for Arzoo Textile Industry (ART) effluent in 6 days followed by Crescent Textile Industry (CRT), Itmad Textile Industry (ITT), Megna Textile Industry (MGT) and Ayesha Textile Industry (AST) effluents. Optimization of different process parameters for ART effluent decolorization by C. versicolor IBL-04 showed that manganese peroxidase (MnP) (486 U/mL) was the lignolytic enzyme present in the culture filtrates with undetectable lignin peroxidase (LiP) and laccase. The MnP synthesis and effluent decolorization could be enhanced to 725 U/mL and 84.4%, respectively, with a significant time reduction to 3 days by optimizing pH and temperature and using 1% starch as a supplementary carbon source.     

Potential of Bacillus cereus for bioremediation of pulp and paper industrial waste

Biotechnological processes have the potential to reduce environmental pollution through their application in processes aimed at resolving waste dumping problems. In this study, Bacillus cereus was assessed for its efficiency to decolorize pulp and paper industrial effluents. The impact of carbon source, nitrogen source, temperature, initial pH and incubation period on color reduction was also studied. The optimum pH and temperature were found to be 6.5 and 45 °C, respectively. B. cereus was efficient at decolorizing the effluents in the presence of glucose, xylose and starch (84, 45.5 and 66 %, respectively), but maximum color reduction (90.6 %) was obtained with 0.5 % sucrose as the carbon source in the presence of 1 % ammonium sulphate. The substantially high load of chemical oxygen demand and biological oxygen demand was decreased by about 61 and 66 %, respectively, by B. cereus. The molecular size distribution studies of control and bacterial-treated effluent samples revealed the degradation of high and medium molecular mass compounds. The results demonstrate the high potential of B. cereus as a significant candidate for color removal from pulp and paper mill effluents.