In vitro monitoring sub-nanogram amounts analgin in human urine by its inhibitory of the luminol-periodate chemiluminescence reaction using reagent immobilization release technique

A selective and sensitive as well as rapid chemiluminescence (CL) flow sensor for the determination of analgin is described. The analytical reagents involved in chemiluminescence reaction, luminol and periodate, were both immobilized on an anion-exchange column. The CL signals produced by the reaction between luminol and periodate, which were eluted from the column through water injection, were decreased in the presence of analgin. Analgin was sensed by measuring the decrement of CL intensity, and which was observed linear over the logarithm of analgin concentration range of 0.1 to 50.0 ng mL(-1), and the limit of detection was 0.04 ng mL(-1) (3ó). At a flow rate of 2.0 mL min(-1), including sampling and washing, the detection could be performed in 0.5 min with a relative standard deviation of less than 3.0%. The proposed procedure was applied successfully in the monitoring of analgin in human urine samples without any pre-treatment process. It was found that the analgin concentration reached its maximum after being orally administrated for 4 h, and the analgin metabolism ratio in 10 h was 9.28% in the body of volunteers. The flow sensor offered reagentless procedures and remarkable stability in determination of analgin, and could be easily reused over 80 h.     

Flow‐injection chemiluminescence method to detect a β2 adrenergic agonist

A new method for the detection of β₂ adrenergic agonists was developed based on the chemiluminescence (CL) reaction of β₂ adrenergic agonist with potassium ferricyanide–luminol CL. The effect of β₂ adrenergic agonists including isoprenaline hydrochloride, salbutamol sulfate, terbutaline sulfate and ractopamine on the CL intensity of potassium ferricyanide–luminol was discovered. Detection of the β₂ adrenergic agonist was carried out in a flow system. Using uniform design experimentation, the influence factors of CL were optimized. The optimal experimental conditions were 1 mmol/L of potassium ferricyanide, 10 µmol/L of luminol, 1.2 mmol/L of sodium hydroxide, a flow speed of 2.6 mL/min and a distance of 1.2 cm from ‘Y₂’ to the flow cell. The linear ranges and limit of detection were 10–100 and 5 ng/mL for isoprenaline hydrochloride, 20–100 and 5 ng/mL for salbutamol sulfate, 8–200 and 1 ng/mL for terbutaline sulfate, 20–100 and 4 ng/mL for ractopamine, respectively. The proposed method allowed 200 injections/h with excellent repeatability and precision. It was successfully applied to the determination of three β₂ adrenergic agonists in commercial pharmaceutical formulations with recoveries in the range of 96.8–98.5%. The possible CL reaction mechanism of potassium ferricyanide–luminol–β₂ adrenergic agonist was discussed from the UV/vis spectra. Copyright © 2014 John Wiley & Sons, Ltd.     

Chemiluminescence inhibition assay for folic acid using flow injection analysis

A new flow injection method for the determination of folic acid is described. A fast oxidation reaction occurred when folic acid was mixed with potassium ferricyanide generating ferrocyanide which then inhibited the chemiluminescent reaction of ferricyanide and luminol in alkaline medium. The decrease of chemiluminescence intensity was correlated with the folic acid concentration in the range 0.1-21 microg/mL; the detection limit for the assay was 0.03 microg/mL (3sigma). A complete analysis of folic acid, including sampling and washing, could be performed within 2 min with a relative standard deviation of less than 4.0%. The proposed method has been applied successfully to the determination of folic acid in pharmaceutical preparations.     

Application of silver nanoparticles to the chemiluminescence determination of cefditoren pivoxil using the luminol–ferricyanide system

A new simple, accurate and sensitive sequential injection analysis chemiluminescence (CL) detection method for the determination of cefditoren pivoxil (CTP) has been developed. The developed method was based on the enhancement effect of silver nanoparticles on the CL signal arising from a luminol–potassium ferricyanide reaction in the presence of CTP. The optimum conditions relevant to the effect of luminol, potassium ferricyanide and silver nanoparticle concentrations were investigated. The proposed method showed linear relationships between relative CL intensity and the investigated drug concentration at the range 0.001–5000 ng/mL, (r = 0.9998, n = 12) with a detection limit of 0.5 pg/mL and quantification limit of 0.001 ng/mL. The relative standard deviation was 1.6%. The proposed method was employed for the determination of CTP in bulk drug, in its pharmaceutical dosage forms and biological fluids such as human serum and urine. The interference of some common additive compounds such as glucose, lactose, starch, talc and magnesium stearate was investigated. In addition, the interference of some related cephalosporins was tested. No interference was recorded. The obtained sequential injection analysis‐CL results were statistically compared with those from a reported method and did not show any significant differences. Copyright © 2014 John Wiley & Sons, Ltd.     

Sensitive determination of synephrine by flow-injection chemiluminescence.

It was found that light emission produced by the oxidation of luminol by potassium ferricyanide in basic medium was enhanced by synephrine, an anti-obesity drug. The optimum conditions for this chemiluminescent reaction were studied in detail in a flow injection system and employed in a new, simple and rapid method for the determination of synephrine. A mechanism for this reaction is proposed, based on the chemiluminescence reaction spectra. In the optimum conditions, CL intensity is proportional to concentration of synephrine in the 0.008-1 microg/mL range. The limit of detection is 1.6 ng/mL for synephrine (3sigma), and the relative standard deviation (n = 11) is 2.6% for 0.5 microg/mL synephrine. The method was applied to the determination of synephrine in herbal products, citrus fruit and biological fluids. The recoveries were satisfactory (90-102%). The results given by the proposed method are in good agreement with those given by HPLC-UV.     

A novel green analytical procedure for monitoring of azoxystrobin in water samples by a flow injection chemiluminescence method with off‐line ultrasonic treatment

A simple and green flow injection chemiluminescence (FI‐CL) method for determination of the fungicide azoxystrobin was described for the first time. CL signal was generated when azoxystrobin was injected into a mixed stream of luminol and KMnO₄. The CL signal of azoxystrobin could be greatly improved when an off‐line ultrasonic treatment was adopted. Meanwhile, the signal intensity increases with the analyte concentration proportionally. Several variables, such as the ultrasonic parameters, flow rate of reagents, concentrations of sodium hydroxide solution and CL reagents (potassium permanganate, luminol) were investigated, and the optimal CL conditions were obtained. Under optimal conditions, the linear range of 1–100 ng/mL for azoxystrobin was obtained and the detection limit (3σ) was determined as 0.13 ng/mL. The relative standard deviation was 1.5% for 10 consecutive measurements of 20 ng/mL azoxystrobin. The method has been applied to the determination of azoxystrobin residues in water samples. Copyright © 2012 John Wiley & Sons, Ltd.     

Flow injection analysis of riboflavin with chemiluminescence detection using a N-halo compounds-luminol system.

A chemiluminescent method for the determination of riboflavin is described. The method is based on the chemiluminescence (CL) generated during the oxidation of luminol by N-bromosuccinimide (NBS) and N-chlorosuccinimide (NCS) in alkaline medium. It was found that riboflavin could greatly enhance this CL intensity when present in the luminol solution. Based on this observation, a new flow-injection CL method for the determination of riboflavin is proposed in this paper. The detection limits were 7.5 ng/mL and 3.5 ng/mL of riboflavin for the NBS- and NCS-luminol CL systems, respectively. The relative CL intensity was linear, with riboflavin concentration in the range 19-600 ng/mL and 600-2000 ng/mL for the NBS-luminol CL system, and 12-200 ng/mL and 200-2000 ng/mL for the NCS-luminol CL system. The results obtained for the assay of pharmaceutical preparations compared well with those obtained by the official method and demonstrated good accuracy and precision.     

Chemiluminescence determination of moxifloxacin in pharmaceutical and biological samples based on its enhancing effect of the luminol–ferricyanide system using a microfluidic chip

A sensitive determination of a synthetic fluoroquinolone antibacterial agent, moxifloxacin (MOX), by an enhanced chemiluminescence (CL) method using a microfluidic chip is described. The microfluidic chip was fabricated by a soft‐lithographic procedure using polydimethyl siloxane (PDMS). The fabricated PDMS microfluidic chip had three‐inlet microchannels for introducing the sample, chemiluminescent reagent and oxidant, and a 500 µm wide, 250 µm deep and 82 mm long microchannel. An enhanced CL system, luminol–ferricyanide, was adopted to analyze the MOX concentration in a sample solution. CL light was emitted continuously after mixing luminol and ferricyanide in the presence of MOX on the PDMS microfluidic chip. The amount of MOX in the luminol–ferricyanide system influenced the intensity of the CL light. The linear range of MOX concentration was 0.14–55.0 ng/mL with a correlation coefficient of 0.9992. The limit of detection (LOD) and limit of quantification (LOQ) were 0.06 and 0.2 ng/mL respectively. The presented method afforded good reproducibility, with a relative standard deviation (RSD) of 1.05% for 10 ng/mL of MOX, and has been successfully applied for the determination of MOX in pharmaceutical and biological samples. Copyright © 2013 John Wiley & Sons, Ltd.     

Simple simultaneous determination of butylated hydroquinone (TBHQ) and butylated hydroxyanisole (BHA) antioxidants in oil using high‐performance liquid chromatography with chemiluminescence detection

A highly sensitive and convenient high‐performance liquid chromatography technique coupled with chemiluminescence detection for the simultaneous determination butylated hydroquinone (TBHQ) and butylated hydroxyanisole (BHA) in oil is established. The detection is based on the inhibitory effect on the CL reaction between luminol and potassium ferricyanide in an alkaline medium. Samples were separated through a reverse‐phase C₁₈ column using a mobile phase of methanol and water (80: 20, v/v) at a flow rate of 0.5 mL/min. The effects of various parameters including mobile phase, flow rate and chemiluminescence regent were studied. Under optimum conditions, both TBHQ and BHA showed good linear relationships in the range 1 × 10^‐7–1 × 10^‐5 g/mL with detection limits of 24 and 33 ng/mL, respectively. The proposed method is simple and sensitive, with low costs. The method was successfully applied for the quantification of TBHQ and BHA in sesame oil. The possible inhibition mechanism is also discussed briefly. Copyright © 2014 John Wiley & Sons, Ltd.     

CdS nanoparticles‐ enhanced chemiluminescence and determination of baicalin in pharmaceutical preparations

CdS nanoparticles (CdS NPs) of different sizes were synthesized by the citrate reduction method. It was found that CdS NPs could enhance the chemiluminescence (CL) of the luminol‐potassium ferricyanide system and baicalin could inhibit CdS NPs‐enhanced luminol‐potassium ferricyanide CL signals in alkaline solution. Based on this inhibition, a flow‐injection CL method was established for determination of baicalin in pharmaceutical preparations and human urine samples. Under optimized conditions, the linear range for determination of baicalin was 5.0 x 10^?6 to 1.0 x 10^?3 g/L. The detection limit at a signal‐to‐noise ratio of 3 was 1.7 x 10 ^?6 g/L. CL spectra, UV‐visible spectra and transmission electron microscopy (TEM) were used to investigate the CL mechanism. The method described is simple, selective and obviates the need of extensive sample pretreatment. Copyright © 2012 John Wiley & Sons, Ltd.     

A novel chemiluminescence method for the determination of orciprenaline based on ferricyanide-rhodamine 6G.

A novel flow injection chemiluminescence method for the determination of orciprenaline was developed. The method is based on the chemiluminescence (CL) reaction of orciprenaline with potassium ferricyanide in sodium hydroxide medium, sensitized by the fluorescent dye rhodamine 6G. The proposed procedure allows quantitation of orciprenaline in the concentration range 0.01-1.2 microg/mL, with a detection limit of 7.2 x 10(-3) microg/mL. The relative standard deviation (RSD) is 2.7% for 0.1 microg/mL orciprenaline (n = 9). The sampling frequency was calculated at approximately 120/h. The method was successfully applied to the determination of orciprenaline in pharmaceutical preparations. A brief discussion on the possible CL reaction mechanism is presented.     

Potential of the luminol reaction in the sensitive detection of pesticide residues by flow injection analysis.

This study presents the first analytical application of the luminol chemiluminescence (CL) reaction for the sensitive detection of carbamate residues. Some experiments have been carried out to check the influence of the presence of traces of a N-methylcarbamate (carbaryl) on the CL emission produced from the oxidation of luminol using different oxidants, showing a significant enhancing effect on the CL emission when the oxidation of luminol is produced by potassium permanganate in alkaline medium, this enhancement being proportional to the carbaryl concentration. This fact has permitted the establishment of a sensitive chemiluminescence flow-injection (CL-FIA) method for the direct determination of carbaryl. The optimization of instrumental and chemical variables influencing the CL response has been carried out by applying experimental designs. Under the optimal conditions, the CL intensity was linear for a carbaryl concentration over the range 5-100 ng/mL with a detection limit of 4.9 ng/mL. This luminol-KMnO4-based FIA-CL system in basic medium shows an easy, fast and cheap alternative detection mode for the analysis of carbaryl residues in environmental water samples.     

Determination of agmatine in biological samples by capillary electrophoresis with chemiluminescence detection

A fast and simple method based on capillary electrophoresis (CE) with chemiluminescence (CL) detection has been developed for the determination of agmatine, a recently identified neurotransmitter/modulator. The CE run time was approximately 2 min for each sample injected. CL detection employed a lab-built reaction flow cell and a photon counter. The CL reagents used were luminol and NaBrO. The optimized conditions for the CL detection were 5 x 10(-4)M luminol added to the CE running buffer and 5.0 x 10(-4)M NaBrO in 100 mM NaCO3-NaOH buffer solution at pH 12.5 introduced post column. Detection limit for agmatine was 4.3 x 10(-6)M (S/N=3). The precision (R.S.D.) on peak height (at 1 x 10(-5)M agmatine) and migration time were 3.7 and 2.5%, respectively. The present CE-CL method was evaluated with the determination of agmatine in tissue samples taken from rat brain, and rat and monkey stomachs. Samples were directly injected into the CE-CL system after the removal of proteins. A higher level of agmatine was detected in the stomach samples. Agmatine concentrations in the tissue samples taken from rat and monkey stomachs were similar at approximately 1950 ng/g wet tissue.     

Post-chemiluminescence behaviour of Ni2+, Mg2+, Cd2+ and Zn2+ in the potassium ferricyanide-luminol reaction.

A new chemiluminescence (CL) reaction was observed when Ni2+, Mg2+, Cd2+ or Zn2+ was injected into the reaction mixture after the finish of the CL reaction of alkaline luminol and potassium ferricyanide. This reaction is described as a post-chemiluminescence (PCL) reaction. The possible mechanism for the PCL was proposed based on studies of the CL kinetic characteristic and the CL spectra. The experimental conditions of the CL reactions were optimized and the feasibility of using the reaction to analyse these metal ions was evaluated. The PCL reaction method operates in the ranges: 1 x 10(-7)-8 x 10(-6) g/L Ni2+; 3 x 10(-6)-2 x 10(-4) g/L Mg2+; 8 x 10(-7)-1 x 10(-4) g/L Cd2+; and 2 x 10(-4)-2 x 10(-3) g/L Zn2+, with detection limits of 4 x 10(-8) g/mL, 1 x 10(-6) g/mL, 3 x 10(-7) g/mL, 8 x 10(-5) g/mL, respectively.     

Flow-injection chemiluminescence determination of catecholamines based on their enhancing effects on the luminol-potassium periodate system.

A rapid and sensitive chemiluminescence (CL) method using flow injection analysis is described for the determination of four catecholamines, dopamine, adrenaline, isoprenaline and noradrenaline, based on their greatly enhancing effects on the CL reaction of luminol-potassium periodate in basic solutions. The optimized chemical conditions for the chemiluminescence reaction were 1.0 x 10(-4) mol/L luminol and 1.0 x 10(-5) mol/L potassium periodate in 0.2 mol/L sodium hydroxide (NaOH). Under the optimized conditions, the calibration graphs relating the CL signal intensity (peak height) to the concentration of the analytes were curvilinear and they were suitable for determining dopamine, adrenaline, isoprenaline, and noradrenaline in the range 0.1-10 ng/mL, 0.1-100 ng/mL, 1-100 ng/mL and 5-50 ng/mL, respectively, with the relative standard deviations of 0.8-1.7%. The detection limits of the method are 0.02 ng/mL for dopamine, 0.01 ng/mL for adrenaline, 0.1 ng/mL for isoprenaline and 2.0 ng/mL for noradrenaline. The sampling frequency was calculated to be about 60/h. The selectivity of the method was good, because a series of common ions or excipients, such as K(+), Ba(2+), CO(3)(2-), NO(3)(-), SO(4)(2-), PO(4)(3-), sodium citrate, sodium bisulphite, oxidate dopamine, starch, lactose, carbamide and gelatin, could not produce interference when their concentrations were 1000-fold than those of dopamine. The present method was successfully applied to the determination of the four catecholamines in pharmaceutical injections.     

A chemiluminescence fiber-optic biosensor system for the determination of glutamine in mammalian cell cultures.

A chemiluminescence fiber-optic biosensor system has been developed for determining glutamine in hybridoma cell cultures producing monoclonal antibodies against viral surface antigens. Glutaminase and glutamate oxidase (GLO) were immobilized onto aminopropyl glass beads via glutaraldehyde activation separately and packed in a column. Two separate columns containing immobilized GLO and catalase were placed upstream to eliminate endogenous glutamate. In the presence of ferricyanide, luminol reacted with hydrogen peroxide released from the enzymatic reactions to produce a chemiluminescence (CL) light signal which was detected and quantitated with a fiber-optic system. In combination with flow injection analysis it was possible to process samples virtually identically, thus avoiding difficulties in reproducing the CL signal. There was an excellent linear relationship between the CL response and standard glutamine concentration in the range 10(-6) to 10(-3) M. A complete analysis could be performed in 2 min including sampling and washing. Each immobilized enzyme column was stable for at least 300 repeated analyses without any loss of activity. When the biosensor system was used for the determination of glutamine in spent mammalian cell cultures, the values obtained compared well with those of high-performance liquid chromatography, thus validating the applicability of the CL fiber-optic system.     

A validated silver‐nanoparticle‐enhanced chemiluminescence method for the determination of citalopram in pharmaceutical preparations and human plasma

A simple and sensitive chemiluminescence (CL) method was developed for the determination of citalopram in pharmaceutical preparations and human plasma. The method is based on the enhancement of the weak CL signal of the luminol–H₂O₂ system. It was found that the CL signal arising from the reaction between alkaline luminol and H₂O₂ was greatly increased by the addition of silver nanoparticles in the presence of citalopram. Prepared silver nanoparticles (AgNPs) were characterized by UV–visible spectroscopy and transmission electron microscopy (TEM). Various experimental parameters affecting CL intensity were studied and optimized for the determination of citalopram. Under optimized experimental conditions, CL intensity was found to be proportional to the concentration of citalopram in the range 40–2500 ng/mL, with a correlation coefficient of 0.9997. The limit of detection (LOD) and limit of quantification (LOQ) of the devised method were 3.78 and 12.62 ng/mL, respectively. Furthermore, the developed method was found to have excellent reproducibility with a relative standard deviation (RSD) of 3.65% (n = 7). Potential interference by common excipients was also studied. The method was validated statistically using recovery studies and was successfully applied to the determination of citalopram in the pure form, in pharmaceutical preparations and in spiked human plasma samples. Percentage recoveries were found to range from 97.71 to 101.99% for the pure form, from 97.84 to 102.78% for pharmaceutical preparations and from 95.65 to 100.35% for spiked human plasma. Copyright © 2013 John Wiley & Sons, Ltd.     

An assay for inorganic mercury(II) based on its post-catalytic enhancement effect on the potassium permanganate-luminol system.

A strong chemiluminescence (CL) response is observed when potassium permanganate solution is injected into basic luminol solution. When the CL reaction terminates, subsequent injection of Hg2+ solution into the reaction mixture results in a new CL reaction. Based on the post-catalytic enhancement effect of Hg2+ on the potassium permanganate-luminol system in basic media, a fast and simple CL-coupled flow injection analysis for the determination of Hg2+ was developed. In optimum conditions, CL intensity is proportional to Hg2+ concentration over the range 1.0 x 10(-8)-1.0 x 10(-5) g/mL, with a detection limit of 2.0 x 10(-9) g/mL. The relative standard deviation (RSD) is 3.6% for 1.0 x 10(-7) g/mL Hg2+ (n = 11). After pretreatment with sulphydryl cotton fibre, environmental water samples were analysed by the proposed method for total mercury determination with satisfactory results. The results were in good agreement with those given by hydride generation-cold vapour atomic absorption spectrometry (HG-CVAAS).     

Flow injection chemiluminescence determination of captopril based on its enhancing effect on the luminol–ferricyanide/ferrocyanide reaction

A new flow injection chemiluminescence method is described for the determination of captopril. It is based on the enhancing effect of captopril on the chemiluminescence reaction of luminol with potassium ferricyanide in alkaline solution in the presence of potassium ferrocyanide. The method allows the determination of captopril over 0.1–40 µg/mL range, with a relative standard deviation (SD) of 1.0% for the determination of 0.5 µg/mL captopril solution in 11 repeated measurements. The method was satisfactorily applied to the determination of captopril in commercial captopril tablets. The possible reaction mechanism is also discussed briefly. Copyright © 2002 John Wiley & Sons, Ltd.     

Catalytic effect of ferricyanide between myoglobin and luminol and effect of temperature.

Specific catalytic oxidation of oxymyoglobin (MbO(2)) and luminol by ferricyanide was studied in a flow-injection system. MbO(2) in different redox states (ferric and ferrous) was oxidized to Mb(Fe(III)) by ferricyanide, and then specific binding of the ferrocyanide anion to Mb(Fe(III)) to the His 119 (GH1) region accelerated the electron transfer between Mb(Fe(III)) and luminol, which produced a chemiluminescence (CL) signal at 425 nm. The increased CL emission was correlated with the myoglobin concentration in the range 0.16-7.5 microg/mL. Thermogravimetry and differential scanning calorimetry were used to investigate the temperature effects on this reaction. The results showed that the CL intensity in the presence of myoglobin changed considerably with heating in the range 15-50 degrees C, and the maximal CL intensity was observed at 40 degrees C, corresponding to the glass transition temperature of myoglobin. The effect of different ligands and interferences were also studied.