Sensitive determination of xylenes in whole blood by capillary gas chromatography with cryogenic trapping

A new and sensitive method for measurement of o-, m- and p-xylenes in human whole blood by capillary gas chromatography (GC) with cryogenic trapping is presented. After heating 0.5 ml of whole blood and 0.5 ml of distilled water containing the xylenes and aniline (internal standard, I.S.) in a 4.0-ml vial at 100°C for 30 min, 2 ml of the headspace vapor was drawn into a glass syringe. All vapor was introduced through the GC port into an AT-Wax middle-bore capillary column in the splitless mode at an oven temperature of 5°C to trap the entire analytes, and the oven temperature was then programmed up to 180°C. The present conditions gave sharp peaks for xylenes and aniline (I.S.), and low background noises for whole blood samples; the peaks of p- and m-xylenes showed about 90% separation with the AT-Wax column. As much as 41.0–46.3% of xylenes, which had been spiked to whole blood could be recovered. The calibration curves showed linearity in the range of 0.1–0.5 μg/0.5 ml of whole blood. The detection limit was estimated to be about 10 ng/0.5 ml. The coefficients of intra-day and inter-day variations for xylenes were not greater than 9.38%. The data for actual detection of xylenes in post-mortem blood of self-ignition suicide cases by the present method were also presented.     

Headspace gas chromatography with capillary column for urine alcohol determination

A headspace gas chromatographic method using a fused-silica capillary column Poraplot Q has been developed and validated for the detection and quantification of ethanol in urine. Under optimized conditions, ethanol was properly separated from acetaldehyde, acetone, isopropanol, methanol and n-propanol. Limits of detection (LODs) and quantification (LOQs) were 0.008 and 0.010 g/l, respectively. The precision studies within-run and between-run, using spiked urine samples (0.08, 0.8 and 2.0 g/l) showed maximum coefficients of variation 5.9 and 6.5%, respectively. Results of ethanol recovery varied from 91.6±0.8 to 103.3±1.8% over the concentration range from 0.01 to 3.20 g/l. The method was appropriate for the detection of ethanol in urine samples. This matrix can be used for monitoring alcohol abuse in the workplace and used in alcohol rehabilitation programs.     

Rapid quantitation of cyanide in whole blood by automated headspace gas chromatography

Cyanide (CN), a chemical asphyxiant, is a rapidly acting and powerful poison. We have developed a sensitive, rapid, simple, and fully automated method for measuring CN in whole blood. The assay is based on the use of gas chromatography (GC) with nitrogen-phosphorus detection and acetonitrile as an internal reference. Following the automated addition of phosphoric acid to the blood sample, the released hydrogen cyanide is analyzed using a fully automated headspace GC system. The assay, validated on human blood samples spiked with potassium cyanide and on clinical samples from fire victims who had smoke inhalation injury, can detect CN at a wide range of concentrations (30-6000 microg/l) in about 17 min (including incubation and GC run time, and <2 min for manual sample preparation). This automated, high-throughput, simple, and sensitive method is suitable for the rapid diagnosis of CN in clinical and forensic specimens.     

Determination of methanol in whole blood by capillary gas chromatography with direct on-column injection

A gas chromatographic procedure was developed for the determination of methanol in small-volume whole blood samples. Samples (100–200 μl) were prepared by protein precipitation, with direct injection of the supernatant on a wide-bore capillary column. The recovery of methanol and acetonitrile (the internal standard) was approximately 90% and did not vary with sample volume. The assay was linear from 2 μg/ml (the limit of detection) through 1000 μg/ml and was highly reproducible (intra-day coefficient of variation <2.5%). Assay performance was assessed following exposure of rats to methanol. The results indicate that the present procedure is suitable for studies of methanol disposition in small rodent species.     

Optimization of solid-phase microextraction conditions for gas chromatographic determination of ethanol and other volatile compounds in blood

A procedure for the determination of acetaldehyde, acetone, methanol, ethanol, 1-propanol and 2-propanol in blood was developed. Separation of analytes was carried out on DB-wax capillary column (l = 30 m, I.D. = 0.32 mm, dF = 0.5 microm) at 40 degrees C, hydrogen was used as a carrier gas (at 30 kPa) and FID as a detector. Quantification was performed with the use of 2-butanol as an internal standard. Headspace solid-phase microextraction was applied as the sample preparation technique. The usefulness of most commercially available fiber coatings was checked and 65 microm Carbowax/DVB proved most effective. Microextraction was carried out from the headspace at 60 degrees C for 10 min. The sample was stirred at 750 rpm. In order to improve the extraction efficiency of analytes, salting-out agents were also applied. Potassium carbonate turned out to be the most efficient. A 1.0-g amount of this salt and 0.1 ml of I.S. were added to 0.5 ml of sample. Validation of the worked-out method was performed. For each analyte, the limits of detection and quantification, linearity, working range, accuracy and precision were determined or tested.     

Determination of cyanide and volatile alkylnitriles in whole blood by headspace solid-phase microextraction and gas chromatography with nitrogen phosphorus detection

Simultaneous determination of cyanide and volatile alkylnitriles such as acetonitrile, cis- and trans-crotononitrile, allylnitrile and butyronitrile at low ppb concentration on whole blood (rat and mice) by headspace solid-phase microextraction (HS-SPME) followed by gas chromatography (GC) with nitrogen phosphorus detection has been achieved for the first time. SPME extraction time and temperature were optimized using a star experimental design. Optimum conditions for cyanide extraction were chosen to analyze unspiked blood samples containing alkylnitriles as that analyte occurs at the lowest concentrations. For all analytes, the developed methodology yielded good quality parameters. In all cases, good reproducibility (relative standard deviation < or =12%), detection limits (<3ng mL(-1)) and quantification limits (<4 ng mL(-1)) were recorded.     

Quantitative determination of histamine metabolites by capillary gas chromatography

A method using capillary gas chromatography is described for the determination of histamine and eight of its basic and acid metabolites in a single biological sample of serum, urine, or gastric juice. Ion-exchange chromatography and extraction with organic solvents are used for isolation and purification, and gas chromatography for identification and quantitation. The heptafluorobutyryl derivatives of histamine and some basic metabolites are compatible with nitrogen-phosphorus and electron capture detection modes and offer an excellent sensitivity (detection limit 0.1 pmol with electron capture). The acid metabolites are quantitated after esterification. The linearity range, the sensitivity, a partial study of reproducibility and typical chromatograms show that the method is adaptable to a variety of applications.     

On-line fermenter headspace gas analysis of methanol and ethanol by capillary inlet mass spectrometry

Summary A new capillary inlet system was used with a magnetic sector mass spectrometer to analyse headspace gas from air-sparged aqueous solutions of methanol and ethanol. The system responded to pulse additions within 2 minutes and gave 90% of equilibrium response after 10 minutes. No memory effects or hysteresis were observed. Signal to concentration ratio was linear with alcohol concentrations up to 5 g/L. Liquid ethanol concentration in aerobic yeast fermentation was followed successfully by on-line headspace gas analysis.     

Estimation of ethanol in fermentation broth by solvent extraction and gas chromatography

Ethanol from fermentation is usually estimated by gas chromatography after centrifuging or distilling the broth. In this paper a more efficient and rapid method is described in which ethanol is extracted by an organic solvent such as n-butanol and the extract is analysed by gas chromatography. The distribution factor determined has a value close to unity and is dependent on ethanol concentration, but independent of sugar concentration.     

Volatile compounds detected in blood of drunk drivers by headspace/capillary gas chromatography/ion trap mass spectrometry.

As shown by others, ethanol and methanol appear in the breath of normals, and endogenous methanol becomes detectable also in the blood after intake of ethanol. In this study I have investigated whether low-molecular-weight volatile organics, other than methanol, arise in the blood of drunk drivers who had imbibed alcoholic beverages. To this end a method for searching for such compounds in the blood is described. It was based on headspace extraction, gas chromatographic separation on a DB-WAX capillary, and ion trap detection in the mass range 29-99 u. Detection limits, as defined by the analyte concentration that gives a signal equal to three times the standard deviation of the baseline noise, were estimated for the different mass numbers used in the substance search. Given the detection limits, presented as mmoles per litre (numbers within parentheses), in every drunk driver's blood with more than 10 mmol l-1 of ethanol between seven and nine different volatile substances were spotted. These were ethanol (0.15), 2-propanone (0.015), ethyl acetate (0.0005), 2-butanone (0.006), methanol (1.5), 2-propanol (0.06), ethanol (0.7), 2-butanol (0.03), and 1-propanol (0.03).     

Determination of remifentanil in human blood by capillary gas chromatography with nitrogen-selective detection

A validated method for the determination of remifentanil in human blood, applicable to all therapeutic concentrations, using capillary GC with nitrogen-specific detection and fentanyl as the internal standard has been developed. Citrated whole blood samples were extracted into 1-chlorobutane following precipitation of proteins with methanol. The drugs were back extracted into 10 mM HCl and re-extracted into methanol-1-chlorobutane. The extracts were reconstituted in methanol and injected onto a 25-m BPX-5 column. The lower limit of quantitation was 0.2 ng/ml with within- and between-day coefficients of variation of less than 15%.     

Reliable gas chromatographic–mass spectrometric method combined with a headspace autosampler for isoflurane determination in blood

Isoflurane is a nonflammable, liquid, volatile inhalation anesthetic administered by vaporizing. Although it is now commonly used, fatal cases resulting from its abuse or misuse have been reported. A combined system of a gas chromatograph–mass spectrometer and a headspace autosampler is therefore proposed for the detection of blood isoflurane. This analytic method showed sharp and well separated peaks, and revealed a good linear relationship (r=0.9994) with a function of y=7.3768x−0.0222 at concentrations between 18.7 and 299.2 μg/ml. The limits of detection and quantitation of this method were 1.2 and 4.7 μg/ml, respectively. The within- and between-run precision for spiked samples, assessed by the coefficient of variations, ranged from 1.7 to 10.0% and from 4.1 to 12.8%, respectively. The within- and between-run accuracy, assessed by errors from theoretical values, were 2.2–7.8% and 2.4–9.6%, respectively. In addition, practical sample analysis showed a good applicability, with a within-run precision rate of 5.6 to 7.7% and a between-run precision rate of 5.2–10.6%. In summary, the present work presents a valid alternative for blood isoflurane analysis.     

Determination of paraldehyde by gas chromatography in whole blood from children

A rapid, sensitive and selective gas chromatographic method with flame ionization detection was developed for the determination of paraldehyde in small blood samples taken from children. Whole blood samples (300 microl) collected in a 3 ml Wheaton glass sample vial were spiked with acetone (internal standard: 15 ng) followed by addition of concentrated hydrochloric acid. The mixture was heated in the sealed airtight sample vial in a water bath (96 Celsius; 5 min) to depolymerize paraldehyde to acetaldehyde. A 2 ml aliquot of the headspace was analyzed by gas chromatography with flame ionization detector using a stainless steel column (3 m x 4 mm i.d.) packed with 10% Carbowax 20 M/ 2% KOH on 80/100 Chromosorb WAW. Calibration curves were linear from 1.0-20 microg (r2>0.99). The limit of detection was 1.5 microg/ml, while relative mean recoveries at 2 and 18 microg were 105.6 +/- 8.4 and 101.2 +/- 5.9%, respectively (n = 10 for each level). Intra- and inter-assay relative standard deviations at 2, 10 and 18 microg were <15%. There was no interference from other drugs concurrently used in children with severe malaria, such as anticonvulsants (diazepam, phenytoin, phenobarbitone), antipyretics/analgesics (paracetamol and salicylate), antibiotics (gentamicin, chloramphenicol, benzyl penicillin) and antimalarials (chloroquine, quinine, proguanil, cycloguanil, pyrimethamine and sulfadoxine). The method was successfully applied for pharmacokinetic studies of paraldehyde in children with convulsions associated with severe malaria.     

Rapid and sensitive static headspace gas chromatography-mass spectrometry method for the analysis of ethanol and abused inhalants in blood

A sensitive and specific method using static headspace gas chromatography coupled with mass spectrometry (GC/MS) has been developed for the quantitative determination of ethanol in biological fluids using n-propanol as internal standard. Gas chromatography was performed in isothermal mode with a GC run time of 2.6 min. The quantification was performed using scan mode abstracting a quantitative ion and a qualifier ion for ethanol and for the internal standard. The method was linear (r(2), 0.999, in the concentration range of 5-200 mg/dl), specific (no interference from methanol acetaldehyde, acetone or from endogenous materials), sensitive (limit of quantification and limit of detection of 0.2 and 0.02 mg/dl, respectively) and robust (less than 5% inter- and intra-assay coefficient of variation). A slightly modified method was also developed for the quantification of five commonly abused inhalants (dichloromethane, ethyl acetate, benzene, toluene and xylene) in blood. The method used a gradient GC program with a run time of 8 min. The quantification was performed using scan mode and integrating the area under the peak using trichloroethane as an internal standard. Without optimization, the method was linear (from 5 to 100 mg/l) and sensitive.     

Improved method for selenium determination in biological samples by gas chromatography

A gas chromatographic assay employing electron-capture detection for the determination of selenium in biological samples is reported. A calibration curve of 4-nitro-o-phenylenediamine derivative of selenium as a function of peak area was linear from 5–1000 pg. The limit of detection for the electron-capture detector was approximately 0.5 pg. Recoveries of selenium added to various biological materials ranged from 95–105%. This procedure reduces the number of transfers thereby reducing errors associated with losses or contamination. One advantage of the present method is that interfering compounds occurring in previously employed chromatographic methods are eliminated. This procedure can be used for routine microanalysis of selenium. Samples containing less than 2 ng selenium in 200 μl of biological fluid can be routinely analyzed using this method.     

Analysis of methanol or formic acid in body fluids by headspace solid-phase microextraction and capillary gas chromatography

Methanol and its metabolite formic acid have been found extractable from human whole blood and urine by headspace solid-phase microextraction (SPME) with a Carboxen/polydimethylsiloxane fiber. The headspace SPME for formic acid was carried out after derivatization to methyl formate under acidic conditions. The determinations of both compounds were made by using acetonitrile as internal standard (IS) and capillary gas chromatography (GC) with flame ionization detection. The headspace SPME–GC gave sharp peaks for methanol, methyl formate and I.S.; and low background noises for whole blood and urine samples. Extraction efficiencies were 0.25–1.05% of methanol and 0.38–0.84% formic acid for whole blood and urine. The calibration curves for methanol and formic acid showed excellent linearity in the range of 1.56 to 800 and 1.56 to 500 μg/0.5 ml of whole blood or urine, respectively. The detection limits were 0.1–0.5 μg/0.5 ml for methanol and 0.6 μg/0.5 ml for formic acid for both body fluids. The within-day relative standard deviations in terms of extraction efficiency for both compounds in whole blood and urine samples were not greater than 9.8%. By using the established SPME method, methanol and formic acid were successfully separated and determined in rat blood after oral administration of methanol.     

Simple determination of cyclosporine in human whole blood by high-performance liquid chromatography

A simple and reproducible high-performance liquid chromatography (HPLC) method was developed for determination of cyclosporine (CyA, also known as cyclosporin A) in human whole blood. The method entailed direct injection of the blood samples after deproteination using acetonitrile. Chromatography was carried out using an ODS column under isocratic elution with acetonitrile-5mM disodium hydrogen phosphate (75:25, v/v), pH 5.1 at 70 degrees C and a detector set at 210 nm. The mean absolute recovery of cyclosporine from blood was 97%, and the linearity was assessed in the range of 100-3000 ng/ml blood, with a correlation coefficient of greater than 0.999. The limit of quantification and detection of the present method were 100 and 50 ng/ml, respectively. This method has been used to analyze several hundred human blood samples for bioavailability studies.     

Automated solid-phase extraction method for the determination of piperaquine in capillary blood applied onto sampling paper by liquid chromatography

A bioanalytical method for the determination of piperaquine in 100 microL blood applied onto sampling paper, by solid-phase extraction and liquid chromatography, has been developed and validated. Blood spots were cut into small pieces prior to addition of 0.3M perchloric acid, acetonitrile and phosphate buffer containing an internal standard. The liquid phase was loaded onto a mixed phase cation-exchange (MPC) solid-phase extraction column. Piperaquine and the internal standard were analysed by liquid chromatography and separated on a Chromolith Performance (100 mm x 4.6 mm) column with acetonitrile:phosphate buffer pH 2.5, I = 0.1 (8:92, v/v) at the flow of 3.5 mL/min. The UV detection was performed at 345 nm. The intra-assay precision was 12.0% at 0.150 microM, 7.3% at 1.25 microM and 7.3% at 2.25 microM. The inter-assay precision was 1.8% at 0.150 microM, 5.2% at 1.25 microM and 2.8% at 2.25 microM. The lower limit of quantification (LLOQ) was determined to 0.050 microM where the precision was 14.7%.