Specimen size effect in the volumetric shrinkage of cancellous bone measured at two levels of dehydration

Water is commonly removed from bone to study its effect on mechanical behaviour; however, dehydration also alters the bone structure. To make matters worse, measuring structural changes in cancellous bone is complicated by a number of factors. Therefore, the goals of this study were to address these issues by (1) comparing Archimedes' method and a helium pycnometer as methods for measuring cancellous bone volume; (2) measuring the apparent dimensional and volumetric tissue shrinkage of cancellous bone at two levels of dehydration; and, (3) identifying whether a size effect exists in cancellous bone shrinkage. Cylindrical specimens (3, 5 and 8.3 mm diameters) of cancellous bone were taken from the distal bovine femur. The apparent dimensions of each cylindrical specimen were measured in a fully hydrated state (HYD), after drying at room temperature (AIR), and after oven drying at 105 degrees C (OVEN). Tissue volume measurements for those three hydration states were obtained using both a helium pycnometer and Archimedes' method. Aluminium foams, which mimic the cancellous structure, were used as controls. The results suggest that the helium pycnometer and Archimedes' method yield identical results in the HYD and AIR states, but that Archimedes' method under-predicts the nominal OVEN volume by incorporating the collagen-apatite porosity. A distinct size effect on volumetric shrinkage is observed (p<0.025) using the pycnometer in both AIR and OVEN states. Apparent dimensional shrinkage (2% and 7%) at the two dehydration levels is much smaller than the measured volumetric tissue shrinkage (16% and 29%), which results in a reduced dehydrated bone volume fraction.     

The dependence of the elastic properties of osteoporotic cancellous bone on volume fraction and fabric

Osteoporosis is a progressive systemic skeletal condition characterized by low bone mass and microarchitectural deterioration, with a consequent increase in susceptibility to fracture. Hence, osteoporosis would be best diagnosed by in vivo measurements of bone strength. As this is not clinically feasible, our goal is to estimate bone strength through the assessment of elastic properties, which are highly correlated to strength. Previously established relations between morphological parameters (volume fraction and fabric) and elastic constants could be applied to estimate cancellous bone stiffness in vivo. However, these relations were determined for normal cancellous bone. Cancellous bone from osteoporotic patients may require different relations. In this study we set out to answer two questions. First, can the elastic properties of osteoporotic cancellous bone be estimated from morphological parameters? Second, do the relations between morphological parameters and elastic constants, determined for normal bone, apply to osteoporotic bone as well? To answer these questions we used cancellous bone cubes from femoral heads of patients with (n=26) and without (n=32) hip fractures. The elastic properties of the cubes were determined using micro-finite element analysis, assuming equal tissue moduli for all specimens. The morphological parameters were determined using microcomputed tomography. Our results showed that, for equal tissue properties, the elastic properties of cancellous bone from fracture patients could indeed be estimated from morphological parameters. The morphology-based relations used to estimate the elastic properties of cancellous bone are not different for women with or without fractures.     

Determination of Chlorophenols in Soils by a Method Involving Alkaline Extraction and Solid-phase Preconcentration Prior to High-performance Liquid Chromatography

A well-reproducible method for determining five common chlorophenols in soils is described. Chlorophenols were extracted from a soil with sodium hydroxide and, after being acidified to pH 6.5, the extract was cleaned by partitioning between chloroform and sodium hydroxide. After adjusting the pH value to 5.5, the sample was concentrated in a C-18 minicolumn. The chlorophenols were desorbed with methanol, the extract was basified, the solvent volume was reduced to 100 μl, and the concentrated extract was acidified. An aliquot was analyzed by HPLC with UV detection (225 nm). Recovery experiments were performed at concentration levels of 1 ppm, 0.1 ppm, and 0.01 ppm. Recovery levels between 65% and 83% with a standard deviation of ±3.75 were achieved at the concentration level of 0.1 ppm. Detection limits between 2 ppb (2,4,6-trichlorophenol) and 2.5 ppb (4-chloro-3-methylphenol) were determined.     

Anisotropy and inhomogeneity of the trabecular structure can describe the mechanical strength of osteoarthritic cancellous bone

Osteoarthritic cancellous bone was studied to investigate the development of this pathology, and the functional changes it induces in the bone. In order to predict how the morphological alterations of the tissue induced by the pathology can change the mechanical properties of the structure, two different strategies have been used in the literature: (1) emphasising the influence of structural anisotropy; (2) stressing the highly inhomogeneous characteristics of cancellous bone. The aim of the present study was to verify the theory that mechanical strength of osteoarthritic cancellous bone depends both on tissue anisotropy and inhomogeneity.Twenty-five specimens were extracted from osteoarthritic femoral heads, along selected directions, and analysed by means of a microtomograph. The same specimens were mechanically tested in compression to determine the mechanical strength. The most representative structural parameters, confirmed by a stepwise analysis, were used to define four models to describe the measured mechanical strength. The models were applied neglecting (global analysis) or considering (local analysis) tissue inhomogeneities to verify whether the correlation with ultimate stress could be improved.The coefficient of determination increased from 0.53, considering only bone volume fraction, up to 0.88, combining it with off-axis angle and normalised eigenvalue. A further improvement was found performing a local analysis (R²=0.90), which corresponded to a decrease of 17% in the residual error.The proposed approach of considering both tissue anisotropy and inhomogeneity improved the accuracy in predicting the mechanical behaviour of cancellous bone tissue and should be suitable for more general loading conditions.     

On the dependence of the elasticity and strength of cancellous bone on apparent density

This paper presents a statistical analysis of the pooled data from a number of previous experiments concerning the dependence of the Young's moduli and strength of cancellous bone tissue upon apparent density. The results show that both the Young's moduli and the strength are proportional to the square of apparent density of the tissue and are therefore proportional to one another. It is shown that the coefficient of proportionality is different for human and bovine tissue. It is concluded that the suggestion of Wolff (Das Gesetz der Transformation der Knochen, Hirschwald, Berlin, 1892) that compact bone tissue is simply more dense cancellous bone tissue is not an accurate statement when only the mechanical properties of these two tissues are considered. It is noted that estimates for the elastic modulus of the individual trabecula of human cancellous bone vary from 1 to 20 GPa and it is suggested that this question needs further study.     

Structural development of the mineralized tissue in the human L4 vertebral body

Knowledge of the structural development of the human vertebrae from non-weight-bearing before birth to weight-bearing after birth is still poor. We studied the mineralized tissue of the developing lumbar L4 vertebral body at ages 15 weeks postconception to 97 years from the tissue level (trabecular architecture) to the material level (micro- and nanostructure). Trabecular architecture was investigated by 2D histomorphometry and the material level was examined by quantitative backscattered electron imaging (for typical calcium content, CaMaxFreq) and scanning small-angle X-ray scattering (for mean mineral particle thickness). During early development, the trabecular orientation changed from a radial to a vertical/horizontal pattern. For bone area per tissue area and trabecular width in postnatal cancellous bone, the maximum was reached at adolescence (20 years), while for trabecular number the maximum was reached at childhood (approximately 1 year). CaMaxFreq was lower in early bone (approximately 21 wt%) than in mineralized cartilage (approximately 29 wt%) and adolescent bone (approximately 23 wt%). In conclusion, the changes at the tissue level were observed to continue throughout life while the development of bone at the material level (CaMaxFreq, mineral particle thickness and orientation) is essentially complete after the first years of life. CaMaxFreq and mean particle thickness increase rapidly during the first years and reach saturation. Remarkably, when these parameters are plotted versus logarithm of age, they appear linear.     

Altered tissue properties induce changes in cancellous bone architecture in aging and diseases

The mechanical properties of cancellous bone depend on its architecture and the tissue properties of the mineralized matrix. The architecture is continuously adapted to external loads. In this paper, it was assumed that changes in tissue properties leading to changes in tissue deformation can induce adaptation of the architecture. We asked whether changes in cancellous bone architecture with aging and in e.g. early osteoarthrosis can be explained from changes in tissue properties.This was investigated using computer models in which the cancellous architecture was adapted to external loads. Bone tissue with deformations below a certain threshold was resorbed, deformations above another threshold induced formation. Deformations between these two boundaries, in the 'lazy zone', did not induce bone adaptation. The effects of changes in bone tissue stiffness on bone mass, global stiffness and architecture were investigated. The bone gain (40-60%) resulting from a 50% decrease in tissue stiffness (simulating diseased tissue) was much larger than the bone loss (2-30%) resulting from a 50% increase in tissue stiffness (simulating highly mineralized, old tissue). The adaptation induced by a decrease in tissue stiffness resulted in an almost constant stiffness in the main load bearing direction, but the transversal stiffness decreased. An increased tissue stiffness resulted in a higher stiffness in the main direction and overcompensation in the transversal directions: the global stiffness could become even smaller than the stiffness of the original model. Concluding, we showed that changes in trabecular bone in aging and diseases can be partly explained from changes in tissue properties.     

Some basic relationships between density values in cancellous and cortical bone

Density is a salient property of bone and plays a crucial role in determining the mechanical properties of both its cancellous and cortical structural forms. Density is defined in a number of ways at either the bone tissue (D(app), apparent) or the bone material level (D(mat), material). The concept of density is relatively simple, but measuring it in the context of bone is a complex issue. The third dimension of the problem is the concept of porosity, or BV/TV (ratio of bone material volume over tissue volume). Recent investigations from our laboratory have revealed an interdependence of D(app) and D(mat) in the cancellous bone of at least four different cohorts of human patients. To clarify the underlying causes of this behaviour, we produced here equivalent relationships from specimens originating from cortical and cancellous areas of the same bone. Plots of D(app) vs. D(mat) showed that D(mat) was not a monotonic function of increasing D(app), but instead showed a 'boomerang'-like pattern. By empirically dissecting the data in two regions for D(app) above and below a value equal to 1.3gcm(-3), we were able to objectively isolate the bone in trabecular and compact forms. Our findings may have implications not only for the segregation of bone in these two structural forms, but also for the mechanobiological and physiological processes that govern the regulation of compact and trabecular bone areas.     

An Investigation into the Feasibility of Implementing Fractal Paradigms to Simulate Cancellous Bone Structure

Abstract

Cancellous bone consists of a framework of solid trabeculae interspersed with bone marrow. The structure of the bone tissue framework is highly convoluted and complex, being fractal and statistically self-similar over a limited range of magnifications. To date, the structure of natural cancellous bone tissue has been defined using 2D and 3D imaging, with no facility to modify and control the structure. The potential of four computer-generated paradigms has been reviewed based upon knowledge of other fractal structures and chaotic systems, namely Diffusion Limited Aggregation (DLA)perolation and Epidemics, Cellular Automata, and a regular Grid with randomly relocated nodes. The resulting structures were compared for their ability to create realistic structures of cancellous bone rather than reflecting growth and form processes. Although the creation of realistic computer-generated cancellous bone structures is difficult, it should not be impossible. Future work considering the combination of fractal and chaotic paradigms is underway.     

Vascularized periosteum associated with cancellous bone graft: an experimental study

The association of a vascularized periosteal flap with a cancellous bone graft was studied on a group of 20 Wistar rats. Ten rats were sacrificed at 6 weeks and seven at 12 weeks (three died prematurely). The behavior of the cancellous bone graft buried in striated muscle and the osteogenic capacity of a simple vascularized periosteal flap also were observed on the same animals. Results of the study are as follows: In 14 of 17 animals, a vascularized periosteal flap wrapped around a cancellous bone graft resulted in new cortical bone formation with little resorption of the initial cancellous graft. A vascularized musculoperiosteal flap has produced a small amount of new compact bone only in 4 of 17 animals. A cancellous bone graft buried into well-vascularized muscle tissue was resorbed (15 cases) or necrotic (2 cases) at 12 weeks. In conclusion, the association of a vascularized periosteal flap and cancellous bone is a better means to produce compact bone than a vascularized periosteal flap alone or an isolated cancellous bone graft.     

A 1,2‐propylene oxide sensor utilizing cataluminescence on CeO2 nanoparticles

A simple and sensitive gas sensor was proposed for the determination of 1,2‐propylene oxide (PO) based on its cataluminescence (CTL) by oxidation in the air on the surface of CeO₂ nanoparticles. The luminescence characteristics and optimal conditions were investigated in detail. Under optimized conditions, the linear range of the CTL intensity versus the concentration of PO was 10–150 ppm, with a correlation coefficient (r) of 0.9974 and a limit of detection (S/N = 3) of 0.9 ppm. The relative standard deviation for 40 ppm PO was 1.2% (n = 7). There was no or only weak response to common foreign substances including acetone, formaldehyde, ethyl acetate, acetic acid, chloroform, propanol, carbon tetrachloride, ether and methanol. There was no significant change in the catalytic activity of the sensor for 100 h. The proposed method was simple and sensitive, with a potential of detecting PO in the environment and industry. Copyright © 2014 John Wiley & Sons, Ltd.     

Additive effect of vitamin K2 and risedronate on long bone mass in hypophysectomized young rats.

Hypophysectomy (HX) arrests bone growth and induces osteopenia in the long bones of rats. The present study investigated the combined effect of vitamin K(2) and risedronate on long bone mass in HX rats, in order to determine whether treatment with these two agents had an additive effect. Forty female Sprague-Dawley rats were hypophysectomized at 6 weeks of age by the supplier, and were shipped to our laboratory at three days after surgery along with ten intact rats that served as age-matched controls. The study was started on the day when the rats were received. Three HX rats were excluded from the study because of the failure of HX. Forty-seven rats (6 weeks old) were assigned to the following 5 groups by the stratified weight randomization method: intact controls, HX alone, HX + vitamin K(2) (30 mg/kg, p.o., daily), HX + risedronate (2.5 microg/kg, s.c., 5 days a week), and HX + vitamin K(2) + risedronate. The dosing period was 4 weeks. HX resulted in a decrease of the femoral bone area, bone mineral content (BMC) and bone mineral density (BMD), as well as a decrease in the cancellous bone mass of the proximal tibial metaphysis and the total tissue and cortical areas of the tibial diaphysis. These changes were associated with a marked reduction in the serum level of insulin like growth factor (IGF)-I and with elevation of serum alkaline phosphatase (ALP) and pyridinoline. Administration of vitamin K(2) increased the serum ALP level in HX rats, but did not affect any of the other parameters. On the other hand, risedronate ameliorated the decrease of femoral BMD and cancellous bone mass at the proximal tibial metaphysis in HX rats without affecting the serum IGF-I level, as a result of not causing a significant elevation of serum pyridinoline. Vitamin K(2) and risedronate combined had an additive effect on the femoral bone area, BMC and BMD, and the combined treatment group did not show any significant reduction of the total tissue and cortical areas at the tibial diaphysis, as well as a reduced serum pyridinoline level compared with untreated rats and an increased serum ALP level compared with untreated or risedronate-treated rats. These results suggest that risedronate had a positive effect on the BMD and cancellous bone mass of long bones in HX rats. Despite the lack of a significant effect of vitamin K(2) on bone mass parameters, it had an additive effect with risedronate on the BMC, BMD and cortical bone mass of long bones in HX rats.     

An investigation into the feasibility of implementing fractal paradigms to simulate cancellous bone structure

Cancellous bone consists of a framework of solid trabeculae interspersed with bone marrow. The structure of the bone tissue framework is highly convoluted and complex, being fractal and statistically self-similar over a limited range of magnifications. To date, the structure of natural cancellous bone tissue has been defined using 2D and 3D imaging, with no facility to modify and control the structure. The potential of four computer-generated paradigms has been reviewed based upon knowledge of other fractal structures and chaotic systems, namely Diffusion Limited Aggregation (DLA), Percolation and Epidemics, Cellular Automata, and a regular Grid with randomly relocated nodes. The resulting structures were compared for their ability to create realistic structures of cancellous bone rather than reflecting growth and form processes. Although the creation of realistic computer-generated cancellous bone structures is difficult, it should not be impossible. Future work considering the combination of fractal and chaotic paradigms is underway.     

Preventive effects of risedronate and calcitriol on cancellous osteopenia in rats treated with high-dose glucocorticoid.

We compared the effects of risedronate (Ris) and calcitriol (Cal) on cancellous osteopenia in rats treated with high-dose glucocorticoid (GC). Forty female Sprague-Dawley rats, 4 months of age, were randomized by the stratified weight method into four groups of 10 rats each according to the following treatment schedule: intact control, and GC administration with vehicle, Ris, or Cal. The GC (methylprednisolone sodium succinate, 5.0 mg/kg, s.c.), Ris (10 microg/kg, s.c.), and Cal (0.1 microg/kg, p.o.) were administered 3 times a week. At the end of the 4-week treatment period, bone histomorphometric analysis was performed for cancellous bone of the proximal tibial metaphysis. The GC administration decreased cancellous bone volume (BV/total tissue volume [TV]), trabecular number (Tb N), and trabecular thickness (Tb Th), as a result of increased bone resorption and decreased bone formation. Ris treatment markedly increased cancellous BV/TV and Tb N above the control level as a result of suppressed bone turnover. On the other hand, Cal treatment attenuated the GC-induced decrease in cancellous BV/TV and Tb Th as a result of suppressed bone resorption and maintained bone formation. This study showed the differential effects of Ris and Cal on cancellous osteopenia in rats treated with high-dose GC.     

Trabecular shear stress in human vertebral cancellous bone: intra- and inter-individual variations

Correlation of the mean and standard deviation of trabecular stresses has been proposed as a mechanism by which a strong relationship between the apparent strength and stiffness of cancellous bone can be achieved. The current study examined whether the relationship between the mean and standard deviation of trabecular von Mises stresses can be generalized for any group of cancellous bone. Cylindrical human vertebral cancellous bone specimens were cut in the infero-superior direction from T12 of 23 individuals (inter-individual group). Thirty nine additional specimens were prepared similarly from the T4-T12 and L2-L5 vertebrae of a 63 year old male (intra-individual group). The specimens were scanned by micro-computed tomography (microCT) and trabecular von Mises stresses were calculated using finite element modeling. The expected value, standard deviation and coefficient of variation of the von Mises stress were calculated form a three-parameter Weibull function fitted to von Mises stress data from each specimen. It was found that the average and standard deviation of trabecular von Mises shear stress were: (i) correlated with each other, supporting the idea that high correlation between the apparent strength and stiffness of cancellous bone can be achieved through controlling the trabecular level shear stress variations, (ii) dependent on anatomical site and sample group, suggesting that the variation of stresses are correlated to the mean stress to different degrees between vertebrae and individuals, and (iii) dependent on bone volume fraction, consistent with the idea that shear stress is less well controlled in bones with low BV/TV. The conversion of infero-superior loading into trabecular von Mises stresses was maximum for the tissue at the junction of the thoracic and lumbar spine (T12-L1) consistent with this junction being a common site of vertebral fracture.     

The role of an effective isotropic tissue modulus in the elastic properties of cancellous bone.

Conceptually, the elastic characteristics of cancellous bone could be predicted directly from the trabecular morphology--or architecture--and by the elastic properties of the tissue itself. Although hardly any experimental evidence exists, it is often implicitly assumed that tissue anisotropy has a negligible effect on the apparent elastic properties of cancellous bone. The question addressed in this paper is whether this is actually true. If it is, then micromechanical finite element analysis (micro-FEA) models, representing trabecular architecture, using an 'effective isotropic tissue modulus' should be able to predict apparent elastic properties of cancellous bone. To test this, accurate multi-axial compressive mechanical tests of 29 whale bone specimens were simulated with specimen-specific micro-FEA computer models built from true three-dimensional reconstructions. By scaling the micro-FEA predictions by a constant tissue modulus, 92% of the variation of Young's moduli determined experimentally could be explained. The correlation even increased to 95% when the micro-FEA moduli were scaled to the isotropic tissue moduli of individual specimens. Excellent agreement was also found in the elastic symmetry axes and anisotropy ratios. The prediction of Poisson's ratios was somewhat less precise at 85% correlation. The results support the hypothesis; for practical purposes, the concept of an 'effective isotropic tissue modulus' concept is a viable one. They also suggest that the value of such a modulus for individual cases might be inferred from the average tissue density, hence the degree of mineralization. Future studies must clarify how specific the tissue modulus should be for different types of bone if adequate predictions of elastic behavior are to be made in this way.     

Quality of intertrochanteric cancellous bone as predictor of femoral stem RSA migration in cementless total hip arthroplasty

In cementless total hip arthroplasty, osteoporosis may jeopardize the achievement of immediate stability and lead to migration of anatomically shaped femoral stems. Poor quality of proximal cancellous bone per se may also affect the rate of osseointegration. In a selected group of female total hip arthroplasty patients (mean age 64 years) with unremarkable medical history, intertrochanteric cancellous bone biopsy was taken from the site of stem implantation. Local bone quality, determined by structural μCT imaging and destructive compression testing of the biopsy tissue, was used as the predictor of three-dimensional stem migration determined by radiostereometric analysis (RSA) up to 24 months. The patients exhibited major differences in mechanical properties of the intertrochanteric cancellous bone, which were closely related to the structural parameters calculated from μCT data. Unexpectedly, the major differences observed in the quality of trochanteric cancellous bone had only minor reflections in the RSA migration of the femoral stems. In statistical analysis, the μCT-based bone mineral density quartile (low, middle, high) was the only significant predictor for stem translation at 24 months (p=0.022) but only a small portion (R(2)=0.16) of the difference in translation could be explained by changes in bone mineral density quartile. None of the other parameters investigated predicted stem migration in translation or rotation. In conclusion, poor quality of intertrochanteric cancellous bone seems to contribute to the risk of implant migration less than expected. Probably also the importance of surgical preservation of intertrochanteric cancellous bone has been over-emphasized for osseointegration of cementless stem.     

Comparison of the linear finite element prediction of deformation and strain of human cancellous bone to 3D digital volume correlation measurements

The mechanical properties of cancellous bone and the biological response of the tissue to mechanical loading are related to deformation and strain in the trabeculae during function. Due to the small size of trabeculae, their motion is difficult to measure. To avoid the need to measure trabecular motions during loading the finite element method has been used to estimate trabecular level mechanical deformation. This analytical approach has been empirically successful in that the analytical models are solvable and their results correlate with the macroscopically measured stiffness and strength of bones. The present work is a direct comparison of finite element predictions to measurements of the deformation and strain at near trabecular level. Using the method of digital volume correlation, we measured the deformation and calculated the strain at a resolution approaching the trabecular level for cancellous bone specimens loaded in uniaxial compression. Smoothed results from linearly elastic finite element models of the same mechanical tests were correlated to the empirical three-dimensional (3D) deformation in the direction of loading with a coefficient of determination as high as 97% and a slope of the prediction near one. However, real deformations in the directions perpendicular to the loading direction were not as well predicted by the analytical models. Our results show, that the finite element modeling of the internal deformation and strain in cancellous bone can be accurate in one direction but that this does not ensure accuracy for all deformations and strains.     

Adaptive changes in micromechanical environments of cancellous and cortical bone in response to in vivo loading and disuse

The skeleton accommodates changes in mechanical environments by increasing bone mass under increased loads and decreasing bone mass under disuse. However, little is known about the adaptive changes in micromechanical behavior of cancellous and cortical tissues resulting from loading or disuse. To address this issue, in vivo tibial loading and hindlimb unloading experiments were conducted on 16-week-old female C57BL/6J mice. Changes in bone mass and tissue-level strains in the metaphyseal cancellous and midshaft cortical bone of the tibiae, resulting from loading or unloading, were determined using microCT and finite element (FE) analysis, respectively. We found that loading- and unloading-induced changes in bone mass were more pronounced in the cancellous than cortical bone. Simulated FE-loading showed that a greater proportion of elements experienced relatively lower longitudinal strains following load-induced bone adaptation, while the opposite was true in the disuse model. While the magnitudes of maximum or minimum principal strains in the metaphyseal cancellous and midshaft cortical bone were not affected by loading, strains oriented with the long axis were reduced in the load-adapted tibia suggesting that loading-induced micromechanical benefits were aligned primarily in the loading direction. Regression analyses demonstrated that bone mass was a good predictor of bone tissue strains for the cortical bone but not for the cancellous bone, which has complex microarchitecture and spatially-variant strain environments. In summary, loading-induced micromechanical benefits for cancellous and cortical tissues are received primarily in the direction of force application and cancellous bone mass may not be related to the micromechanics of cancellous bone.     

Alterations in damage processes in dense cancellous bone following gamma-radiation sterilization

Structurally intact cancellous bone allograft is an attractive tissue form because its high porosity can provide space for delivery of osteogenic factors and also allows for more rapid and complete in-growth of host tissues. Gamma radiation sterilization is commonly used in cancellous bone allograft to prevent disease transmission. Commonly used doses of gamma radiation sterilization (25–35 kGy) have been shown to modify cortical bone post-yield properties and crack propagation but have not been associated with changes in cancellous bone material properties. The purpose of this study was to determine the effects of irradiation on the elastic and yield properties and microscopic tissue damage processes in dense cancellous bone. Cancellous bone specimens (13 control, 14 irradiated to 30 kGy) from bovine proximal tibiae were tested in compression to 1.3% apparent strain and examined for microscopic tissue damage. The yield strain in irradiated specimens (0.93±0.11%, mean±SD) did not differ from that in control specimens (0.90±0.11%, p=0.44). No differences in elastic modulus were observed between groups after accounting for differences in bone volume fraction. However, irradiated specimens showed greater residual strain (p=0.01), increased number of microfractures (p=0.02), and reduced amounts of cross-hatching type damage (p<0.01). Although gamma radiation sterilization at commonly used dosing (30 kGy) does not modify elastic or yield properties of dense cancellous bone, it does cause modifications in damage processes, resulting in increased permanent deformation following isolated overloading.