Microwave‐assisted sintering synthesis of greenish‐yellow emitting Sr2SiO4:Eu2+ phosphors

Europium ion (Eu²⁺) doped Sr₂SiO₄ phosphors with greenish‐yellow emission were synthesized using microwave‐assisted sintering. The phase structure and photoluminescence (PL) properties of the obtained phosphor samples were investigated. The PL excitation spectra of the Sr₂SiO₄:Eu²⁺ phosphors exhibited a broad band in the range of 260 nm to 485 nm with a maximum at 361 nm attributed to the 5f‐4d allowed transition of the Eu²⁺ ions. Under an excitation at 361 nm, the Sr₂SiO₄:Eu²⁺ phosphor exhibited a greenish‐yellow emission peak at 541 nm with an International‐Commission‐on‐Illumination (CIE) chromaticity of (0.3064, 0.4772). The results suggest that the microwave‐assisted sintering method is promising for the synthesis of phosphors owing to the decreased sintering time without the use of additional reductive agents.     

Photoluminescence and thermoluminescence properties of Eu2+ doped and Eu2+,Dy3+ co‐doped Ba2MgSi2O7 phosphors

In this work, we report the preparation, characterization, comparison and luminescence mechanisms of Eu²⁺‐doped and Eu²⁺,Dy³⁺‐co‐doped Ba₂MgSi₂O₇ (BMSO) phosphors. Prepared phosphors were synthesized via a high temperature solid‐state reaction method. All prepared phosphors appeared white. The phase structure, particle size, and elemental analysis were analyzed using X‐ray diffraction (XRD), transmission electron microscopy (TEM) and energy‐dispersive X‐ray (EDX) analysis. The luminescence properties of the phosphors were investigated by thermoluminescence (TL) and photoluminescence (PL). The PL excitation and emission spectra of Ba₂MgSi₂O₇:Eu²⁺ showed the peak to be around 381 nm and 490 nm respectively. The PL excitation spectrum of Ba₂MgSi₂O₇:Eu²⁺Dy³⁺ showed the peak to be around 341 nm and 388 nm, and the emission spectrum had a broad band around 488 nm. These emissions originated from the 4f⁶ 5d¹ to 4f⁷ transition of Eu²⁺. TL analysis revealed that the maximum TL intensity was found at 5 mol% of Eu²⁺ doping in Ba₂MgSi₂O₇ phosphors after 15 min of ultraviolet (UV) light exposure. TL intensity was increased when Dy³⁺ ions were co‐doped in Ba₂MgSi₂O₇:Eu²⁺ and maximum TL intensity was observed for 2 mol% of Dy³⁺. TL emission spectra of Ba_1.95MgSi₂O₇:0.05Eu²⁺ and Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors were found at 500 nm. TL intensity increased with UV exposure time up to 15 min, then decreased for the higher UV radiation dose for both Eu doping and Eu,Dy co‐doping. The trap depths were calculated to be 0.54 eV for Ba_1.95MgSi₂O₇:0.05Eu²⁺ and 0.54 eV and 0.75 eV for Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors. It was observed that co‐doping with small amounts of Dy³⁺ enhanced the thermoluminescence properties of Ba₂MgSi₂O₇ phosphor. Copyright © 2016 John Wiley & Sons, Ltd. [Correction added on 5 April 2016, after first online publication: The following parts of the abstract have been edited for consistency. '4f65d1' has been corrected to '4f⁶ 5d¹', '4f7' has been corrected to '4f⁷', 'Ba1.95' has been corrected to 'Ba_1.95' and 'Ba1.93' has been corrected to 'Ba_1.93' respectively.]     

Insights into the discrepant luminescence for BaSiO3:Eu2+ phosphors prepared by solid‐state reaction and precipitation reaction methods

Two synthesis routes, solid‐state reaction and precipitation reaction, were employed to prepare BaSiO₃:Eu²⁺ phosphors in this study. Discrepancies in the luminescence green emission at 505 nm for the solid‐state reaction method sample and in the yellow emission at 570 nm for the sample prepared by the precipitation reaction method, were observed respectively. A detail investigation about the discrepant luminescence of BaSiO₃:Eu²⁺ phosphors was performed by evaluation of X‐ray diffraction (XRD), photoluminescence (PL)/photoluminescence excitation (PLE), decay time and thermal quenching properties. The results showed that the yellow emission was generated from the BaSiO₃:Eu²⁺ phosphor, while the green emission was ascribed to a small amount of Ba₂SiO₄:Eu²⁺ compound that was present in the solid‐state reaction sample. This work clarifies the luminescence properties of Eu²⁺ ions in BaSiO₃ and Ba₂SiO₄ hosts.     

Luminescence in Ba2Sr2Al2O7:RE (RE = Tb3+,Eu3+ and Dy3+) novel aluminate phosphors

The luminescence of novel rare earth ( Tb ^{3 +} , Eu ^{3 +} and Dy ^{3 +} )‐activated Ba ₂ Sr ₂ Al ₂ O ₇ phosphors for solid‐state lighting is presented. The aluminate phosphors were synthesized using a one‐step combustion method. X‐Ray diffraction, scanning electron microscopy and photoluminescence characterizations were performed to understand the mechanism of excitation and the corresponding emission in the as‐prepared phosphor, as characterized the phase purity and microstructure. Improvements in the luminescence properties of the phosphors with rare earth concentration were observed. The phosphor hue could be tuned from blue, green and red by proper selection of rare earth ions in typical concentrations. Effective absorption in the near‐ultraviolet region was observed, which makes the phosphor a potential candidate for ultraviolet light‐emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd.     

Luminescence enhancement of (Sr1–xMx)2SiO4:Eu2+ phosphors with M (Ca2+/Zn2+) partial substitution for white light‐emitting diodes

Eu²⁺‐doped Sr₂SiO₄ phosphor with Ca²⁺/Zn²⁺ substitution, (Sr_1–xM_x)₂SiO₄:Eu²⁺ (M = Ca, Zn), was prepared using a high‐temperature solid‐state reaction method. The structure and luminescence properties of Ca²⁺/Zn²⁺ partially substituted Sr₂SiO₄:Eu²⁺ phosphors were investigated in detail. With Ca²⁺ or Zn²⁺ added to the silicate host, the crystal phase could be transformed between the α‐form and the β‐form of the Sr₂SiO₄ structure. Under UV excitation at 367 nm, all samples exhibit a broad band emission from 420 to 680 nm due to the 4f⁶5d¹ → 4f⁷ transition of Eu²⁺ ions. The broad emission band consists of two peaks at 482 and 547 nm, which correspond to Eu²⁺ ions occupying the ten‐fold oxygen‐coordinated Sr.(I) site and the nine‐fold oxygen‐coordinated Sr.(II) site, respectively. The luminescence properties, including the intensity and lifetime of Sr₂SiO₄:Eu²⁺ phosphors, improved remarkably on Ca²⁺/Zn²⁺ addition, and promote its application in white light‐emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd.     

Effect of different temperatures to remove reduction gas on the photoluminescence properties of Eu‐doped Li2(Ba1‐xSrx)SiO4 phosphors

In this study, Eu‐doped Li₂(Ba_1‐xSr_x)SiO₄ powders (x = 0, 0.2, 0.4, and 0.6) were synthesized at 850°C in a reduction atmosphere (5% H₂ + 95% N₂) for a duration of 1 h using a solid‐state reaction method. The reduction atmosphere was infused as the synthesis temperature reached 850°C, and was removed as the temperature dropped to 800–500°C. Li₂(Ba_1‐xSr_x)SiO₄ (or Li₂BaSiO₄), (Ba,Sr)₂SiO₄ (or BaSiO₄), and Li₄SiO₄ phases co‐existed in the synthesized Eu‐doped Li₂(Ba_1‐xSr_x)SiO₄ powders. A new finding was that the reduction atmosphere removing (RAR) temperature of the Li₂(Ba_1‐xSr_x)SiO₄ phosphors had a large effect on their photoluminescence excitation (PLE) and PL properties. Except for the 800°C‐RAR‐treated Li₂BaSiO₄ phosphor, PLE spectra of all other Li₂(Ba_1‐xSr_x)SiO₄ phosphors had one broad emission band with two emission peaks centred at ~242 and ~283 nm; these PL spectra had one broad emission band with one emission peak centred at 502–514 nm. We showed that the 800°C‐RAR‐treated Li₂BaSiO₄ phosphor emitted a red light and all other Li₂(Ba_1‐xSr_x)SiO₄ phosphors emitted a green light. Reasons for these results are discussed thoroughly.     

Luminescence and energy‐transfer properties of color‐tunable Ca2Mg0.25Al1.5Si1.25O7:Ce3+/Eu2+/Tb3+ phosphors for ultraviolet light‐emitting diodes

A series of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺/Eu²⁺/Tb³⁺ phosphors was been prepared via a conventional high temperature solid‐state reaction and their luminescence properties were studied. The emission spectra of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺ and Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Tb³⁺ phosphors show not only a band due to Ce³⁺ ions (409 nm) but also as a band due to Eu²⁺ (520 nm) and Tb³⁺ (542 nm) ions. More importantly, the effective energy transfer from Ce³⁺ to Eu²⁺ and Tb³⁺ ions was confirmed and investigated by emission/excitation spectra and luminescent decay behaviors. Furthermore, the energy level scheme and energy transfer mechanism were investigated and were demonstrated to be of resonant type via dipole–dipole (Ce³⁺ to Eu²⁺) and dipole–quadrupole (Ce³⁺ to Tb³⁺) reactions, respectively. Under excitation at 350 nm, the emitting color could be changed from blue to green by adjusting the relative doping concentration of Ce³⁺ and Eu²⁺ ions as well as Ce³⁺ and Tb³⁺ ions. The above results indicate that Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺/Tb³⁺ are promising single‐phase blue‐to‐green phosphors for application in phosphor conversion white‐light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Persistent luminescence of CaMgSi2O6:Eu2+,Dy3+ and CaMgSi2O6:Eu2+,Ce3+ phosphors prepared using the solid‐state reaction method

CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were synthesized using the solid‐state reaction method. X‐Ray diffraction (XRD) and photoluminescence (PL) analyses were used to characterize the phosphors. The XRD results revealed that the synthesized CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were crystalline and are assigned to the monoclinic structure with a space group C2/c. The calculated crystal sizes of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors with a main (221) diffraction peak were 44.87 and 53.51 nm, respectively. Energy‐dispersive X‐ray spectroscopy (EDX) confirmed the proper preparation of the sample. The PL emission spectra of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors have a broad band peak at 444.5 and 466 nm, respectively, which is due to electronic transition from 4f⁶5d¹ to 4f⁷. The afterglow results indicate that the CaMgSi₂O₆:Eu²⁺,Dy³⁺ phosphor has better persistence luminescence than the CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphor. Copyright © 2015 John Wiley & Sons, Ltd.     

Structural characterization and optical properties of Ca2MgSi2O7:Eu2+,Dy3+ phosphor by solid‐state reaction method

Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor was prepared by the solid‐state reaction method under a weak reducing atmosphere. The obtained phosphor was characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray spectroscopy (EDX) and Fourier transform infrared (FT‐IR) techniques. The phase structure of the Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor was akermanite type, which is a member of the melilite group. The surface morphology of the sintered phosphor was not uniform and phosphors aggregated tightly. EDX and FT‐IR spectra confirm the elements present in the Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor. Under UV excitation, a broadband emission spectrum was found. The emission spectra observed in the green region centered at 535 nm, which is due to the 4f–5d transition. The mechanoluminescence (ML) intensity of the prepared phosphor increased linearly with increases in the mechanical load. The ML spectra were similar to the photoluminescence (PL), which indicates that ML is emitted from the same emitting center of Eu²⁺ ions as PL. Copyright © 2014 John Wiley & Sons, Ltd.     

Photoluminescence properties and energy transfer in Ce3+/Dy3+ co‐doped Sr3MgSi2O8 phosphors for potential application in ultraviolet white light‐emitting diodes

Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ phosphors were prepared by a solid‐state reaction technique and the photoluminescence properties were investigated. The emission spectra show not only a band due to Ce³⁺ ions (403 nm) but also as a band due to Dy³⁺ ions (480, 575 nm) (UV light excitation). The photoluminescence properties reveal that effective energy transfer occurs in Ce³⁺/Dy³⁺ co‐doped Sr₃MgSi₂O₈ phosphors, and the co‐doping of Ce³⁺ could enhance the emission intensity of Dy³⁺ to a certain extent by transferring its energy to Dy³⁺. The Ce³⁺/Dy³⁺ energy transfer was investigated by emission/excitation spectra, and photoluminescence decay behaviors. In Sr_2.94MgSi₂O₈:0.01Ce³⁺, 0.05Dy³⁺ phosphors, the fluorescence lifetime of Dy³⁺ (from 3.35 to 27.59 ns) is increased whereas that of Ce³⁺ is greatly decreased (from 43.59 to 13.55 ns), and this provides indirect evidence of the Ce³⁺ to Dy³⁺ energy transfer. The varied emitted color of Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ phosphors from blue to white were achieved by altering the concentration ratio of Ce³⁺ and Dy³⁺. These results indicate Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ may be as a candidate phosphor for white light‐emitting diodes. Copyright © 2012 John Wiley & Sons, Ltd.     

Tunable white light emission from single‐phased Li2SrSiO4:Dy3+ phosphors by co‐doping with Eu3+

A series of single‐phase full‐color emitting Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors were synthesized by solid‐state reaction and characterized by X‐ray diffraction and photoluminescence analyses. The samples showed emission peaks at 488 nm (blue), 572 nm (yellow), 592 nm (orange) and 617 nm (red) under 393 nm excitation. The photoluminescence excitation spectra, comprising the Eu–O charge transfer band and 4f–4f transition bands of Dy³⁺ and Eu³⁺, range from 200 to 500 nm. The Commission Internationale de I'Eclairage chromaticity coordinates for Li₂Sr_0.98−xSiO₄:0.02Dy³⁺,xEu³⁺ phosphors were simulated. By manipulating Eu³⁺ and Dy³⁺ concentrations, the color points of Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ were tuned from the greenish‐white region to white light and eventually to reddish‐white region, demonstrating that a tunable white light can be obtained by Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors. Li₂Sr_0.98−xSiO₄:0.02Dy³⁺, xEu³⁺ can serve as a white‐light‐emitting phosphor for phosphor‐converted light‐emitting diode. Copyright © 2014 John Wiley & Sons, Ltd.     

Enhancement of the photoluminescence and long afterglow properties of Sr2MgSi2O7:Eu2+ phosphor by Dy3+ co‐doping

Sr₂MgSi₂O₇:Eu²⁺ and Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ long afterglow phosphors were synthesized under a weak reducing atmosphere by the traditional high temperature solid state reaction method. The synthesized phosphors were characterized by powder X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDX), and photo‐, thermo‐ and mechanoluminescence spectroscopic techniques. The phase structure of the sintered phosphor was an akermanite type structure, which belongs to tetragonal crystallography. The thermoluminescence properties of these phosphors were investigated and compared. Under ultraviolet light excitation, the emission spectra of both prepared phosphors were composed of a broad emission band peaking at 470 nm. When the Sr₂MgSi₂O₇:Eu²⁺ phosphor was co‐doped with Dy³⁺, the photoluminescence (PL), afterglow and mechanoluminescence (ML) intensity were strongly enhanced. The decay graph indicated that both the sintered phosphors contained fast decay and slow decay processes. The ML intensities of Sr₂MgSi₂O₇:Eu²⁺ and Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphors were increased proportionally with increasing impact velocity, a finding that suggests that these phosphors could be used as sensors to detect the stress of an object. Copyright © 2015 John Wiley & Sons, Ltd.     

Mechanoluminescence of SrAl2O4:Eu,Dy nanophosphors induced by low impact velocity

The present paper reports the impulsive excitation of mechanoluminescence (ML) in Sr_0.97Al₂O₄:Eu_0.01,Dy_0.02 nanophosphors prepared using a combustion technique. The phosphors are characterized using X‐ray powder diffraction (XRD), high‐resolution transmission electron microscopy (HRTEM) and photoluminescence (PL). The XRD results show that the samples exhibit a monoclinic α‐phase in the crystal structure. The space group of SrAl₂O₄:Eu,Dy nanophosphors is monoclinic P2₁. The PL and ML spectra of SrAl₂O₄:Eu,Dy nanophosphors are excited using light with a wavelength of 365 nm and emission is found at 516 nm. The prepared nanophosphors exhibits an intense ML that can be seen in daylight with the naked eye. When a sample powder is deformed impulsively by the impact of a moving piston, the ML intensity initially increases linearly with time, attains a peak value, I_m, at time t_m, and then decreases with time. The peak ML intensity, I_m, and total ML intensity, I_T, increase linearly with applied pressure and impact velocity. The ML intensity decreases with successive impacts of load onto the phosphors, and the diminished ML intensity can be approximately recovered by UV irradiation. The activation energy using thermoluminescence is found to be 0.57 eV for SrAl₂O₄:Eu,Dy nanophosphors. Copyright © 2016 John Wiley & Sons, Ltd.     

Synthesis and luminescent properties of novel BaGd2O4:Eu3+ scintillating phosphor

BaGd_2‐xO₄:xEu³⁺ and Ba_1‐yGd_1.79‐2yEu_0.21Na_3yO₄ phosphors were synthesized at 1300°C in air by conventional solid‐state reaction method. Phosphors were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE) spectra, photoluminescence (PL) spectra and thermoluminescence (TL) spectra. Optimal PL intensity for BaGd_2‐xO₄:xEu³⁺ and Ba_1‐yGd_1.79‐2yEu_0.21Na_3yO₄ phosphors at 276 nm excitation were found to be x = 0.24 and y = 0.125, respectively. The PL intensity of Eu³⁺ emission could only be enhanced by 1.3 times with incorporation of Na⁺ into the BaGd₂O₄ host. Enhanced luminescence was attributed to the flux effect of Na⁺ ions. However, when BaGd₂O₄:Eu³⁺ phosphors were codoped with Na⁺ ions, the induced defects confirmed by TL spectra impaired the emission intensity of Eu³⁺ ions. Copyright © 2012 John Wiley & Sons, Ltd.     

Luminescence properties of green‐emitting Ca2MgSi2O7:Eu2+ phosphor by a solid‐state reaction method

A europium (Eu)‐doped di‐calcium magnesium di‐silicate phosphor, Ca₂MgSi₂O₇:Eu²⁺, was prepared using a solid‐state reaction method. The phase structure, particle size, surface morphology, elemental analysis, different stretching mode and luminescence properties were analyzed by X‐ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM) with energy dispersive X‐ray spectroscopy (EDX), Fourier transform infrared (FTIR) spectroscopy, photoluminescence (PL) and mechanoluminescence (ML). The phase structure of Ca₂MgSi₂O₇:Eu²⁺ was an akermanite‐type structure, which belongs to the tetragonal crystallography with space group P4?2₁m; this structure is a member of the melilite group and forms a layered compound. The surface of the prepared phosphor was not found to be uniform and particle distribution was in the nanometer range. EDX and FTIR confirm the components of Eu²⁺‐doped Ca₂MgSi₂O₇ phosphor. Under UV excitation, the main emission peak appeared at 530 nm, belonging to the broad emission ascribed to the 4f⁶5d¹→4f⁷ transition of Eu²⁺. The ML intensity of the prepared phosphor increased linearly with increasing impact velocity. A CIE color chromaticity diagram and ML spectrum confirmed that the prepared Ca₂MgSi₂O₇:Eu²⁺ phosphor would emit green color and the ML spectrum was similar to that of PL, which indicated that ML is emitted from the same center of Eu²⁺ ions. Copyright © 2015 John Wiley & Sons, Ltd.     

Sol–gel synthesis and luminescence property of Sr4Al2O7:Re3+,R+ (Re = Eu and Dy; R = Li,Na and K) phosphors for white LEDs

Sr₄Al₂O₇:Eu³⁺ and Sr₄Al₂O₇:Dy³⁺ phosphors with alkali metal substitution were prepared using a sol–gel method. The effects of a charge compensator R on the structure and luminescence of Sr₄Al₂O₇:Re³⁺,R⁺ (Re = Eu and Dy; R = Li, Na and K) phosphors were investigated in detail. Upon heating to 1400°C, the structure of the prepared samples was that of the standard phase of Sr₄Al₂O₇. Under ultraviolet excitation, all Sr₄Al₂O₇:Eu³⁺,R⁺ samples exhibited several narrow emission peaks ranging from 550 to 700 nm due to the 4f → 4f transition of Eu³⁺ ions. All Sr₄Al₂O₇:Dy³⁺,R⁺ phosphors showed two emission peaks at 492 and 582 nm, due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. The luminescence intensity of Sr₄Al₂O₇:Re³⁺,R⁺ (Re = Eu and Dy; R = Li, Na and K) phosphors improved markedly upon the addition of charge compensators, promoting their application in white light‐emitting diodes with a near‐ultraviolet chip.     

Photoluminescent properties of Eu3+‐Eu2+ activated MAl2SixO2x + 4 (M = Mg,Ca, Sr,Ba) phosphors prepared in air

In this paper, MAl₂Si_xO_2x+4:Eu²⁺/Eu³⁺ (Eu²⁺ + Eu³⁺ = 2%, molar ratio; M = Mg, Ca, Sr, Ba; x = 0, 0.5, 1, 1.5, 2) phosphors with different SiO₂ concentrations (the ratio of SiO₂ to MAl₂O₄ is n%, n = 0, 50, 100, 150, 200, respectively) were prepared by high‐temperature solid‐state reaction under atmospheric air conditions. Their structures and photoluminescent properties were systematically researched. The results indicate that Eu³⁺ ions have been reduced and Eu²⁺ ions are obtained in air through the self‐reduction mechanism. The alkaline earth metal ions and doping SiO₂ strongly affect the crystalline phase and photoluminescent properties of samples, including microstructures, relative intensity of Eu²⁺ to Eu³⁺, location of emission lines/bands. It is interesting and important that the emission color and intensities of europium‐doped various phosphors which consist of aluminosilicate matrices prepared under atmospheric air conditions could be modulated by changing the kinds of alkaline earth metal and the content of SiO₂.     

Tunable luminescence and energy transfer in Ca3SiO4Cl2:Ce3+,Li+,Mn2+,Eu2+ phosphors

A series of color‐tunable Ca_{3–2x‐y‐z}SiO₄Cl₂ (CSC):xCe³⁺,xLi⁺,yMn²⁺,zEu²⁺ phosphors with low temperature phase structure was synthesized via the sol–gel method. An energy transfer process from Ce³⁺ to Mn²⁺ in CSC:0.01Ce³⁺,0.01Li⁺,yMn²⁺ (y = 0.03–0.09) and the mechanism was verified to be an electric dipole–dipole interaction. The Ce³⁺ and Mn²⁺ emission intensities were greatly enhanced by co‐doping Eu²⁺ ions into CSC:0.01Ce³⁺,0.01Li⁺,0.07Mn²⁺ phosphors due to competitive energy transfers from Eu²⁺/Ce³⁺ to Mn²⁺, and Ce³⁺ to Eu²⁺. Under 332 nm excitation, CSC:0.01Ce³⁺,0.01Li+,0.07Mn²⁺,zEu²⁺ (z = 0.0005–0.002) exhibited tunable emission colors from green to white with coexisting orange, green and violet‐blue emissions. These phosphors could have potential application in white light‐emitting diodes.     

Molten salt synthesis and luminescence of Dy3+‐doped Y3Al5O12 phosphors

Dy³⁺‐doped Y₃Al₅O₁₂ phosphors were prepared at a relatively low temperature using molten salt synthesis. The phase of the prepared Dy³⁺‐doped Y₃Al₅O₁₂ phosphors was confirmed using X‐ray powder diffraction. Results indicated that Dy³⁺ doping did not change the Y₃Al₅O₁₂ phase. Following excitation at 352 nm, emission spectra of the Dy³⁺‐doped Y₃Al₅O₁₂ phosphors consisted of blue, yellow, and red emission bands. The influence of Dy³⁺ concentration and excitation wavelength on emission was investigated. The ratio of yellow light to blue light varied with change in Dy³⁺ doping concentration, due to changes in the structure around Dy³⁺. Emission intensities also changed when the excitation wavelength was changed. This variation is luminescence generated a system for tunable white light for Dy³⁺‐doped Y₃Al₅O₁₂ phosphors.     

Studies on the luminescence properties of cerium co‐doping on Ca2MgSi2O7:Eu2+ phosphor by solid‐state reaction method

Ca₂MgSi₂O₇:Ce³⁺, Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺,Ce³⁺ phosphors were prepared using the solid‐state reaction method. The crystal structures of the sintered phosphors were of melilite type, which has a tetragonal crystallography. The chemical compositions of the sintered phosphors was confirmed by energy dispersive X‐ray spectroscopy. The different thermoluminescence kinetic parameters [activation energy (E), frequency factor (s) and order of the kinetics (b)] of these phosphors were evaluated and compared using the peak shape method. Under ultraviolet excitation, the emission spectra of both Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺,Ce³⁺ phosphors were composed of a broad emission band peaking at 530 nm. When the Ca₂MgSi₂O₇:Eu²⁺ phosphor is co‐doped with Ce³⁺ ions, photoluminescence, afterglow and mechanoluminescence intensity was strongly enhanced. Ca₂MgSi₂O₇:Eu²⁺ showed some afterglow with a short persist time. On incorporation of Ce³⁺, efficient energy transfer from Ce³⁺ to Eu²⁺ was found and the emission intensity of Eu²⁺ was enhanced. The mechanoluminescence intensities of Ca₂MgSi₂O₇:Ce³⁺, Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺,Ce³⁺ phosphors increased proportionally increased with the increase in impact velocity, which suggests that these phosphors can be used as sensors to detect stress in an object.