<Emphasis Type="Italic">Tetraselmis suecica</Emphasis> culture for CO<Subscript>2</Subscript> bioremediation of untreated flue gas from a coal-fired power station

The accumulation of atmospheric CO₂, primarily due to combustion of fossil fuels, has been implicated in potential global climate change. The high rate of CO₂ bioremediation by microalgae has emerged as a favourable method for reducing coal-fired power plant emissions. However, coal-fired power station flue gas contains other chemicals such as SO_x which can inhibit microalgal growth. In the current study, the effect of untreated flue gas as a source of inorganic carbon on the growth of Tetraselmis in a 1000 L industrial-scale split-cylinder internal-loop airlift photobioreactor was examined. The culture medium was recycled after each harvest. Tetraselmis suecica grew very well in this airlift photobioreactor during the 7-month experiment using recycled medium from an electroflocculation harvesting unit. Increased medium SO₄ ^2? concentration as high as 870 mg SO₄ ^2??L^?1 due to flue gas addition and media recycling had no negative effect on the overall growth and productivity of this alga. The potential organic biomass productivity and carbon sequestration using an industrial-scale airlift PBR at International Power Hazelwood, Gippsland, Victoria, Australia, are 178.9?±?30 mg L^?1 day^?1 and 89.15?±?20 mg?‘C’?L^?1 day^?1, respectively. This study clearly indicates the potential of growing Tetraselmis on untreated flue gas and using recycled medium for the purpose of biofuel and CO₂ bioremediation.     

Biomass productivity of two <Emphasis Type="Italic">Scenedesmus</Emphasis> strains cultivated semi-continuously in outdoor raceway ponds and flat-panel photobioreactors

Semi-continuous algal cultivation was completed in outdoor flat-panel photobioreactors (panels) and open raceway ponds (raceways) from February 17 to May 7, 2015 for side-by-side comparison of areal productivities at the Arizona Center for Algae Technology and Innovation in Mesa, AZ, USA. Experiments used two strains of Scenedesmus acutus (strains LB 0414 and LB 0424) to assess productivity, areal density, nutrient removal, and harvest volume across cultivation systems and algal strains. Panels showed an average biomass productivity of 19.0?±?0.6 g m^?2 day^?1 compared to 6.62?±?2.3 g m^?2 day^?1 for raceways. Photosynthetic efficiency ranged between 1.32 and 2.24 % for panels and between 0.30 and 0.68 % for raceways. Panels showed an average nitrogen consumption rate of 38.4?±?8.6 mg N L^?1 day^?1. Cultivation in raceways showed a consumption rate of 3.8?±?2.5 and 7.1?±?4.2 mg N L^?1 day^?1 for February/March and April/May, respectively, due to increase in biomass productivity. Excess nutrients were required to prevent a decrease in productivity. Daily biomass harvest volumes between 18 and 36 % from panels did not affect culture productivity, but density decreased with increased harvest volume. High cultivation temperatures above 30 °C caused strain LB 0414 to lyse and crash. Strain LB 0424 did not show any difference in biomass productivity when peak temperatures reached 34, 38, or 42 °C, but showed decreased productivity when the peak temperature during cultivation was 30 °C. Using algal strains with different temperature tolerances can generate increased annual biomass productivity.     

Cultivation of <Emphasis Type="Italic">Chlorella vulgaris</Emphasis> with swine wastewater and potential for algal biodiesel production

In this study, an alga-based simultaneous process of treating swine wastewater (SWW) and producing biodiesel was explored. Chlorella vulgaris (UTEX-265) was employed as a model species, and a SWW-based medium was prepared by dilution with tap water. Chlorella vulgaris grew well in the SWW-based medium, and at optimum dilution ratios, it exceeded the conventional culture medium in terms of biomass concentration and productivity. In eightfold diluted SWW, which supported the maximum growth, biomass productivity was 0.247 g L^?1 day^?1, while the productivity was merely 0.165 g L^?1 day^?1 in standard tris-acetate-phosphorous (TAP) algal medium. In addition, fatty acid methyl ester (FAME) productivity was greater in the SWW-based medium (0.067 versus 0.058 g L^?1 day^?1). This enhanced productivity resulted in more than 95 % removal of both nitrogen and phosphorous. All these show that C. vulgaris cultivation is indeed possible in a nutrient-rich wastewater with appropriate dilution, and in so doing, the wastewater can effectively be treated.     

Biological CO<Subscript>2</Subscript> fixation using C<Emphasis Type="Italic">hlorella vulgaris</Emphasis> and its thermal characteristics through thermogravimetric analysis

The present research is focused on cultivation of microalgae strain Chlorella vulgaris for bio-fixation of CO₂ coupled with biomass production. In this regard, a single semi-batch vertical tubular photobioreactor and four similar photobioreactors in series have been employed. The concentration of CO₂ in the feed stream was varied from 2 to 12 % (v/v) by adjusting CO₂ to air ratio. The amount of CO₂ capture and algae growth were monitored by measuring decrease of CO₂ concentration in the gas phase, microalgal cell density, and algal biomass production rate. The results show that 4 % CO₂ gives maximum amount of biomass (0.9 g L^?1) and productivity (0.118 g L^?1 day^?1) of C. vulgaris in a single reactor. In series reactors, average productivity per reactor found to be 0.078 g L^?1 day^?1. The maximum CO₂ uptake for single reactor also found with 4 % CO_2, and it is around 0.2 g L^?1 day^?1. In series reactors, average CO₂ uptake is 0.13 g L^?1 day^?1 per reactor. TOC analysis shows that the carbon content of the produced biomass is around 40.67 % of total weight. The thermochemical characteristics of the cultivated C. vulgaris samples were analyzed in the presence of air. All samples burn above 200 °C and the combustion rate become faster at around 600 °C. Almost 98 wt% of the produced biomass is combustible in this range.     

The effect of temperature on growth and lipid and fatty acid composition on marine microalgae used for biodiesel production

Cultivation temperature is one of the major factors affecting the growth and lipid accumulation of microalgae. In this study, the effects of temperature on the growth, lipid content, fatty acid composition and biodiesel properties of the marine microalgae Chaetoceros sp. FIKU035, Tetraselmis suecica FIKU032 and Nannochloropsis sp. FIKU036 were investigated. These species were cultured at different temperatures (25, 30, 35 and 40 °C). The results showed that the specific growth rate, biomass and lipid content of all microalgae decreased with increasing temperature. With regards to fatty acids, the presence of saturated fatty acids (SFAs) in T. suecica FIKU032 and Nannochloropsis sp. FIKU036 decreased with increasing temperature, in contrast with polyunsaturated fatty acids (PUFAs). Moreover, Chaetoceros sp. FIKU035 was the only species that could grow at 40 °C. The highest lipid productivity was observed in Chaetoceros sp. FIKU035 when cultivated at 25 °C (66.73 ± 1.34 mg L^?1 day^?1) and 30 °C (61.35 ± 2.89 mg L^?1 day^?1). Moreover, the biodiesel properties (cetane number, cold filter plugging point, kinematic viscosity and density) of the lipids obtained from this species were in accordance with biodiesel standards. This study indicated that Chaetoceros sp. FIKU035 can be considered as a suitable species for biodiesel production in outdoor cultivation.     

The effect of gradual increase in salinity on the biomass productivity and biochemical composition of several marine,halotolerant<Emphasis Type="Bold">,</Emphasis> and halophilic microalgae

Open ponds are the preferred cultivation system for large-scale microalgal biomass production. To be more sustainable, commercial scale biomass production should rely on seawater, as freshwater is a limiting resource, especially in places with high irradiance. If seawater is used for both pond fill and evaporative volume makeup, salinity of the growth media will rise over time. It is not possible for any species to achieve optimum growth over the whole saline spectrum (from seawater salinity level up to salt saturation state). In this study, we investigated the effects of gradual salinity increase (between 35 and 233 ppt) on biomass productivity and biochemical composition (lipid and carbohydrate) of six marine, two halotolerant, and a halophilic microalgae. A gradual and slow stepped salinity increase was found to expand the salinity tolerance range of tested species. A gradual reduction in biomass productivity and maximum photochemical efficiency was observed as a consequence of increased salinity in all tested species. Among the marine microalgae, Tetraselmis showed highest biomass productivity (32 mg L^?1 day^?1) with widest salinity tolerance range (35 to 109 ppt). Halotolerant Amphora and Navicula were able to grow from 35 ppt to 129 ppt salinity. Halophilic Dunaliella was the only species capable of growing between 35 and 233 ppt and showed highest lipid content (56.2%) among all tested species. This study showed that it should be possible to maintain high biomass in open outdoor cultivation utilizing seawater by growing Tetraselmis, Amphora, and Dunaliella one after another as salinity increases in the cultivation system.     

Population biology and long-term mariculture studies in the brown alga <Emphasis Type="BoldItalic">Lessonia trabeculata</Emphasis> in Atacama,Chile

Lessonia trabeculata is one of the most valuable seaweeds in Chile, especially in the northern zone where its harvest has been going on for decades. We carried out population dynamics studies in the Atacama Desert coast (Bahia Chasco), in order to assess its productivity under natural and harvesting scenarios. We found very slow but consistent growth (1.98 cm month^?1) and density (3–4 individuals m^?2 with no monthly variation) during 18 months of observations in an undisturbed subpopulation. However, after total harvesting, L. trabeculata exhibited different responses. Its recruitment was season-specific, with exceedingly high values in autumn (ca. 80 individuals m^?2 in 5 months) and a dramatic reduction of recruits in summer (1–5 individuals m^?2 in 7 months, with many areas with no recruitment). Gradually, density values tended to stabilize to growth rates under un-altered conditions. In parallel, pruning systems at three different thallus levels (frond meristem base cuts, removal of half and total canopy) were all inefficient and harmful: (i) Biomass takes longer to be harvested; (ii) pruned individuals die off; and (iii) do not detach easily from the substrata, delaying the recovery by potentially emerging L. trabeculata juveniles. Some of these results agreed with our culture experiments, where 26 months were needed to obtain up to 100 cm long thalli with shrub-like morphology. We conclude that management of L. trabeculata beds must be improved in order to guarantee survival of the industry, and we propose some practices that at some stage should involve the complete removal of older/senescent individuals.     

Effect of cement industry flue gas simulation on the physiology and photosynthetic performance of <Emphasis Type="Italic">Chlorella sorokiniana</Emphasis>

Cement plants account for significant emissions of CO₂ and other pollutants into the atmosphere. As a means for its mitigation, we tested the effect of a cement industry-based flue gas simulation (FGS — 18% CO₂, 9% O₂, 300 ppm NO₂, 140 ppm SO₂) on the green alga, Chlorella sorokiniana. Culture pH, cell density, cell viability and productivity, specific growth rates, photosynthetic performance, and biochemical composition were monitored. The treatments consisted of different FGS volumes (0.1, 0.3, 0.8, 1.5, 6, and 48 L day^?1) that were applied in a series of laboratory-scale semi-continuous batch cultures under controlled conditions. Controls were exposed to 18% CO₂ enriched air. Cell density showed that C. sorokiniana was able to grow in all treatments, but compared to the controls, low pH (~ 5.0) caused by 48 L FGS day^?1 led to 27% decrease in specific growth rate. Increasing FGS exposure decreased maximum and operational quantum yields obtained by pulse amplitude modulated fluorometry, while photochemical quenching remained constant (~ 0.93). The α and rETR _max parameters calculated from rapid light curves decreased with increasing FGS exposure. Total proteins and carbohydrates (per cell basis) increased after 6 and 48 L FGS day^?1, which can be advantageous for biotechnological applications, but cell productivity (cells L^?1 day^?1) decreased. Despite the effects in physiology, C. sorokiniana could withstand a pH range of 6.0–5.0 imposed by 48 L FGS day^?1. Overall, C. sorokiniana can be considered a robust species in flue gas bioremediation.     

Mixotrophic cultivation of <Emphasis Type="Italic">Chlorococcum</Emphasis> sp. under non-controlled conditions using a digestate from pig manure within a biorefinery

A number of business opportunities may arise from microalgae and wastewater treatment becoming an integrated system, as biofuels and high-added value products could be obtained simultaneously. This study, performed under controlled and non-controlled conditions, aimed at cultivating Chlorococcum sp. using a digestate from pig manure as culture medium and assessing its growth and biochemical composition for further applications. Under controlled conditions, cultures of Chlorococcum sp. were established testing various digestate dilutions (v/v). It was found that all tested dilutions (up to 8% v/v) promoted a higher biomass density, compared to the control culture in modified Bold’s Basal Medium (modified BBM). Under non-controlled conditions, it was found that the biomass productivity using the digestate diluted 5.6% v/v (23.4 mg L^?1 day^?1) was statistically similar to the one obtained using modified BBM (26.4 mg L^?1 day^?1). The volatile fatty acids contained in the digestate might have allowed mixotrophic growth for Chlorococcum sp. The intracellular lipid content in Chlorococcum sp. remained constant throughout the experiments in both, treatment and control cultures, while carbohydrates increased from 20 to 45% of the cell dry weight in the treatment and from 20 to 42% in the control one. It was concluded that conditions of nitrogen starvation and fluctuating irradiance and temperature benefit carbohydrate accumulation in this strain, since intracellular carbohydrate content increased nearly two-fold during this period. Additionally, the obtained biomass has the potential to be used as feedstock for bioethanol production. This system can meet the concept of a microalgae-based biorefinery, in which biofuels and high-added value products are produced from microalgae and wastewater.     

<Emphasis Type="Italic">Chlorella vulgaris</Emphasis> (SAG 211-12) biofilm formation capacity and proposal of a rotating flat plate photobioreactor for more sustainable biomass production

Difficulties and cost of suspended microalgal biomass harvest and processing can be overcome by cultivating microalgae as biofilms. In the present work, a new photoautotrophic biofilm photobioreactor, the rotating flat plate photobioreactor (RFPPB), was developed aiming at a cost-effective production of Chlorella vulgaris (SAG 211-12), a strain not frequently referred in the literature but promising for biofuel production. Protocols were developed for evaluating initial adhesion to different materials and testing the conditions for biofilm formation. Polyvinyl chloride substrate promoted higher adhesion and biofilm production, followed by polypropylene, polyethylene, and stainless steel. The new RFPPB was tested, aiming at optimizing incident light utilization, minimizing footprint area and simplifying biomass harvesting. Tests show that the photobioreactor is robust, promotes biofilm development, and has simple operation, small footprint, and easy biomass harvest. Biomass production (dry weight) under non-optimized conditions was 3.35 g m^?2, and areal productivity was 2.99 g m^?2 day^?1. Lipid content was 10.3% (dw), with high PUFA content. These results are promising and can be improved by optimizing some operational parameters, together with evaluation of long-term photobioreactor maximum productivity.     

The growth of <Emphasis Type="Italic">Chlorella sorokiniana</Emphasis> as influenced by CO<Subscript>2</Subscript>, light,and flue gases

In order to achieve recognition as environmentally friendly production, flue gases should be used as a CO₂ source for growing the microalgae Chlorella sorokiniana when used for hydrogen production. Flue gases from a waste incinerator and from a silicomanganese smelter were used. Before testing the flue gases, the algae were grown in a laboratory at 0.04, 1.3, 5.9, and 11.0 % (v/v) pure CO₂ gas mixed with fresh air. After 5 days of growth, the dry biomass per liter algal culture reached its maximum at 6.1 % CO₂. A second experiment was conducted in the laboratory at 6.2 % CO₂ at photon flux densities (PFD) of 100, 230, and 320 μmol photons m^?2 s^?1. After 4 days of growth, increasing the PFD increased the biomass production by 67 and 108 % at the two highest PFD levels, as compared with the lowest PFD. A bioreactor system containing nine daylight-exposed tubes and nine artificial light-exposed tubes was installed on the roof of the waste incinerator. The effect of undiluted flue gas (10.7 % CO₂, 35.8 ppm NO _x , and 38.6 ppm SO₂), flue gas diluted with fresh air to give 4.2 % CO₂ concentration, and 5.0 % pure CO₂ gas was studied in daylight (21.4?±?9.6 mol photons m^?2 day^?1 PAR, day length 12.0 h) and at 135 μmol photons m^?2 s^?1 artificial light given 24 h day^?1 (11.7?±?0.0 mol photons m^?2 day^?1 PAR). After 4 days’ growth, the biomass production was the same in the two flue gas concentrations and the 5 % pure CO₂ gas control. The biomass production was also the same in daylight and artificial light, which meant that, in artificial light, the light use efficiency was about twice that of daylight. The starch concentration of the algae was unaffected by the light level and CO₂ concentration in the laboratory experiments (2.5–4.0 % of the dry weight). The flue gas concentration had no effect on starch concentration, while the starch concentration increased from about 1.5 % to about 6.0 % when the light source changed from artificial light to daylight. The flue gas from the silicomanganese smelter was characterized by a high CO₂ concentration (about 17 % v/v), low oxygen concentration (about 4 %), about 100 ppm NO _x , and 1 ppm SO₂. The biomass production using flue gas significantly increased as compared with about 5 % pure CO₂ gas, which was similar to the biomass produced at a CO₂ concentration of 10–20 % mixed with N₂. Thus, the enhanced biomass production seemed to be related to the low oxygen concentration rather than to the very high CO₂ concentration.     

Improvement of biomass and fatty acid productivity in ocean cultivation of <Emphasis Type="Italic">Tetraselmis</Emphasis> sp. using hypersaline medium

In this study, hypersaline media were used for ocean cultivation of the marine microalga Tetraselmis sp. KCTC12432BP for enhanced biomass and fatty acid (FA) productivity. Hypersaline media (55, 80, and 105 PSU) were prepared without sterilization by addition of NaCl to seawater obtained from Incheon, Korea. The highest biomass productivity was obtained at 55 PSU (0.16 g L^?1 day^?1) followed by 80 PSU (0.15 g L^?1 day^?1). Although the specific growth rate of Tetraselmis decreased at salinities higher than 55 PSU, prevention of contamination led to higher biomass productivity at 80 PSU than at 30 PSU (0.03 g L^?1 day^?1). FA content of algal biomass increased as salinity increased to 80 PSU, above which it declined, and FA productivity was highest at 80 PSU. Ocean cultivation of Tetraselmis was performed using 50-L tubular module photobioreactors and 2.5-kL square basic ponds, closed- and open-type ocean culture systems, respectively. Culturing microalgae in hypersaline medium (80 PSU) improved biomass productivities by 89 and 152% in closed and open cultures, respectively, compared with cultures with regular salinity. FA productivity was greatly improved by 369% in the closed cultures. The efficacy of salinity shift and N-deficiency to enhance FA productivity was also investigated. Lowering salinity to 30 PSU with N-starvation following cultivation at 80 PSU improved FA productivity by 19% in comparison with single-stage culture without N-deficiency at 30 PSU. The results show that salinity manipulation could be an effective strategy to improve biomass and FA productivity in ocean cultivation of Tetraselmis sp.     

Field assessment of environmental factors constraining the development and expansion of <Emphasis Type="Italic">Schoenoplectus californicus</Emphasis> marsh at a California tidal freshwater restoration site

The effective restoration of wetland habitats requires understanding the establishment requirements, growth responses, and expansion dynamics of targeted plant species. This is particularly true when restoring areas that have been previously managed for other activities, such as agriculture, which can have legacy effects on the local environment. We investigated environmental factors (specifically hydrology and soil physicochemical conditions) that may influence the establishment, growth and expansion of Schoenoplectus californicus in a tidal freshwater marsh restoration site in the Sacramento–San Joaquin Delta, California, USA. This study site was previously leveed, drained, and utilized for agricultural production. A 1997 levee breach restored tidal connectivity and wetland vegetation has re-established in portions of the area. Our approach coupled an intensively-sampled transect study in S. californicus-dominated marshes with a spatially-extensive survey of S. californicus lateral expansion rates and elevation. Lateral expansion of S. californicus marsh edge was significantly less in lower elevation areas (0.61 ± 0.04 m NAVD88), whereas the marsh edge at higher elevations (0.84 ± 0.03 m NAVD88) exhibited greater expansion, often at rates greater than 1.0 m year^?1. These elevation means correspond to percentages of time that the marsh surface was flooded of 100 and 94 %, respectively. Although marsh edge expansion was influenced by elevation and the resultant hydrology, other factors, such as physical exposure of marsh shorelines and compacted agricultural soils also appear to be important. However, once established, S. californicus appears to be able to ameliorate high soil bulk densities over time as the advancing marsh platform develops.     

Magnetophoretic harvesting of freshwater microalgae using polypyrrole/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocomposite and its reusability

A magnetophoretic harvesting agent, a polypyrrole/Fe₃O₄ magnetic nanocomposite, is proposed as a cost and energy efficient alternative to recover biomass of the microalgae Botryococcus braunii, Chlorella protothecoides, and Chlorella vulgaris from their culture media. The maximal recovery efficiency reached almost 99 % for B. braunii, 92.4 % for C. protothecoides, and 90.8 % for C. vulgaris. The maximum adsorption capacity (Q ₀) of the magnetic nanocomposite for B. braunii (63.49 mg dry biomass mg^?1 PPy/Fe₃O₄) was higher than that for C. protothecoides (43.91 mg dry biomass mg^?1 PPy/Fe₃O₄) and C. vulgaris (39.98 mg dry biomass mg^?1 PPy/Fe₃O₄). The highest harvesting efficiency for all the studied microalgae were at pH 10.0, and measurement of zeta-potential confirmed that the flocculation was induced by charge neutralization. This study showed that polypyrrole/Fe₃O₄ can be a promising flocculant due to its high efficacy, low dose requirements, short settling time, its integrity with cells, and with great potential for saving energy because of its recyclability.     

Bioturbation by the sand dollar <Emphasis Type="Italic">Encope emarginata</Emphasis> (Echinoidea,Mellitidae) changes the composition and size structure of microphytobenthic assemblages

The goal of this study is to examine the suitability of three plants, Typha spp., Phragmites spp. and Iris pseudacorus, in a free-water surface constructed wetland created to treat eutrophic water from Lake Albufera (Valencia, Spain), a wetland of international importance. The growth, coverage and nutrient content of the three plants were studied, and chemical analyses were performed according to standard methods. The maximum standing crops measured for each plant were 1.9, 18.2 and 3.3 kg m^?2, respectively, and their average nutrient concentrations were 2.1, 1.2 and 1.7 g P kg^?1 and 12.1, 11.7 and 10.1 g N kg^?1, respectively. A multiple harvest of Iris pseudacorus revealed that the removal of nutrients could be increased up to 50% for N and 100% for P compared with a single harvest. Biomass decomposition assays showed high values for five-day biochemical oxygen demand (115–207 mg O₂ g^?1, depending on the plant and its age) and a substantial release of phosphorus, up to 100% of that contained in the biomass, highlighting the need to remove the litter fall. This study provides key aspects for vegetation selection and management (planting and harvesting) in a novel application of constructed wetlands to enhance water quality and biodiversity.     

Process Engineering for High-Cell-Density Cultivation of Lipid Rich Microalgal Biomass of <Emphasis Type="Italic">Chlorella</Emphasis> sp. FC2 IITG

In the present study, process engineering strategy was applied to achieve lipid-rich biomass with high density of Chlorella sp. FC2 IITG under photoautotrophic condition. The strategy involved medium optimization, intermittent feeding of limiting nutrients, dynamic change in light intensity, and decoupling growth and lipid induction phases. Medium optimization was performed using combinations of artificial neural network or response surface methodology with genetic algorithm (ANN-GA and RSM-GA). Further, a fed-batch operation was employed to achieve high cell density with intermittent feeding of nitrate and phosphate along with stepwise increase in light intensity. Finally, mutually exclusive biomass and lipid production phases were decoupled into two-stage cultivation process: biomass generation in first stage under nutrient sufficient condition followed by lipid enrichment through nitrogen starvation. The key findings were as follows: (i) ANN-GA resulted in an increase in biomass titer of 157 % (0.95 g L^?1) in shake flask and 42.8 % (1.0 g L^?1) in bioreactor against unoptimized medium at light intensity of 20 μE m^?2 s^?1; (ii) further optimization of light intensity in bioreactor gave significantly improved biomass titer of 5.6 g L^?1 at light intensity of 250 μE m^?2 s^?1; (iii) high cell density of 13.5 g L^?1 with biomass productivity of 675 mg L^?1 day^?1 was achieved with dynamic increase in light intensity and intermittent feeding of limiting nutrients; (iv) finally, two-phase cultivation resulted in biomass titer of 17.7 g L^?1 and total lipid productivity of 313 mg L^?1 day^?1 which was highest among Chlorella sp. under photoautotrophic condition.     

Interspecific biodiversity enhances biomass and lipid productivity of microalgae as biofuel feedstock

Large improvements in biomass and lipid production are required to make massive scale algal biodiesel production an economic reality. The application of the biodiversity strategy to enhance algal biomass as biofuel feedstock is little. The algal diversity was manipulated in this study to investigate the effects of a combination of biodiversity complementarity and a new medium consisting of seawater and agricultural fertilizer on lipid productivity. The algae diverse community includes two strains of Dunaliella salina (Dunaliella salina 19/30 and 19/18) and three species of Nannochloropsis (Nannochloropsis oculata, Nannochloropsis salina, and Nannochloropsis gaditana). The results showed that the most diverse community (5 species) produced an average of sixfold more biomass in the new medium than did the standard f/2 culture medium. The most diverse polyculture had the highest growth rate (1.01 day^?1), biomass (1.2 g L^?1), and lipid productivity (0.31 g L^?1 day^?1). The assessment of algal polycultures relative to monocultures is particularly interesting and novel for this biofuel field, and the observations that these polycultures resulted in significant lipid productivity improvements are very useful addition to the biofuel research. The possible mechanism (resource diversity) to explain the synergy in mixed cultures warrants further investigation.     

Characterization of cell structural change,growth, lipid accumulation,and pigment profile of a novel oleaginous microalga, <Emphasis Type="Italic">Vischeria stellata</Emphasis> (Eustigmatophyceae), cultured with different initial nitrate supplies

The appropriate microalgal species and the optimal nitrogen supply in culture medium are vital factors in maximizing biomass and metabolite productivities in microalgae. Vischeria stellata is an edaphic unicellular eustigmatophycean microalga. Cytological and ultrastructural characteristics and the effects of different initial nitrate-nitrogen concentrations on growth, lipid accumulation, fatty acid profile, and pigment composition were investigated in the present study. The cell structures of V. stellata changed with the degree of nutrient utilization and growth phase. The initial nitrate concentration for the optimal growth of V. stellata ranged from 6.0 to 9.0 mM. The maximum total lipid (TLs), neutral lipid (NLs), and total fatty acid (TFAs) contents were 55.9, 51.9, and 44.7 % of dry biomass, respectively. The highest volumetric productivity of TLs, NLs, and TFAs reached 0.28, 0.25, and 0.21 g L^?1 day^?1, respectively. V. stellata had a suitable fatty acid profile for biodiesel production, as well as containing eicosapentaenoic acid (EPA) for nutraceutical applications. In addition, the content β-carotene, increased gradually as culture time was prolonged, resulting in its exclusive production at the end of cultivation. V. stellata is a promising microalgal strain for the production of biofuels and bioproducts.     

Growth and photosynthetic activity of <Emphasis Type="Italic">Botryococcus braunii</Emphasis> biofilms

Botryococcus braunii is a green microalga capable of producing large amounts of external long-chain hydrocarbons suitable as a source of biofuel. There have been several studies indicating that cultures of B. braunii can reduce the energy and water requirement for mass biofuel production, especially if non-destructive extraction methods for milking hydrocarbons are used. Growing microalgae as a raw material for biofuel using conventional liquid-based cultivation (i.e., raceway ponds) has yet to be shown to be economically successful. An alternative solid growth (biofilm) cultivation method can markedly reduce the energy requirements and costs associated with the harvesting and dewatering processes. We evaluated the growth of biofilms of several strains of B. braunii (from races A, B, L and S) and found that three of the four tested races successfully grew to stationary phase in 10 weeks with no contamination. Among all races, B. braunii BOT22 (race B) reached the highest biomass and lipid yields (3.80 mg dry weight cm^?2 day^?1 and 1.11 mg dry weight cm^?2). Irrespective of the race, almost all photosynthetic parameters (F _V /F ₀ , PI_ABS and the OJIP curve) showed that the biofilm cultures were more stressed during lag and stationary phases than in logarithmic phase. We also studied the Botryococcus biofilm profiles using confocal microscopy and found that this method is suitable for estimating the overall biomass yield when compared with gravimetric measurement. In conclusion, the growth characteristics (biomass and lipid) and photosynthetic performance of all races indicated that B. braunii BOT22 is the most promising strain for biofilm cultivation.     

Biomass and terpenoids produced by mutant strains of <Emphasis Type="Italic">Arthrospira</Emphasis> under low temperature and light conditions

The filamentous Cyanobacterium Arthrospira is commercially produced and is a functional, high-value, health food. We identified 5 low temperature and low light intensity tolerant strains of Arthrospira sp. (GMPA1, GMPA7, GMPB1, GMPC1, and GMPC3) using ethyl methanesulfonate mutagenesis and low temperature screening. The 5 Arthrospira strains grew rapidly below 14?°C, 43.75 μmol photons m^?2 s^?1 and performed breed conservation at 2.5?°C, 8.75 μmol photons m^?2 s^?1. We used morphological identification and molecular genetic analysis to identify GMPA1, GMPA7, GMPB1 and GMPC1 as Arthrospira platensis, while GMPC3 was identified as Arthrospira maxima. Growth at different culture temperatures was determined at regular intervals using dry biomass. At 16?°C and 43.75 μmol photons m^?2 s^?1, the maximum dry biomass production and the mean dry biomass productivity of GMPA1, GMPB1, and GMPC1 were 2057?±?80 mg l^?1, 68.7?±?2.5 mg l^?1 day^?1, 1839?±?44 mg l^?1, 60.6?±?1.8 mg l^?1 day^?1, and 2113?±?64 mg l^?1, 77.7?±?2.5 mg l^?1 day^?1 respectively. GMPB1 was chosen for additional low temperature tolerance studies and growth temperature preference. In winter, GMPB1 grew well at mean temperatures <10?°C, achieving 3258 mg dry biomass from a starting 68 mg. In summer, GMPB1 grew rapidly at mean temperatures more than 28?°C, achieving 1140 mg l^?1 dry biomass from a starting 240 mg. Phytonutrient analysis of GMPB1 showed high levels of C-phycocyanin and carotenoids. Arthrospira metabolism relates to terpenoids, and the methyl-d-erythritol 4-phosphate pathway is the only terpenoid biosynthetic pathway in Cyanobacteria. The 1-deoxy-d-xylulose 5-phosphate reductoisomerase (DXR) gene from GMPB1 was cloned and phylogenetic analysis showed that GMPB1 is closest to the Cyanobacterium Oscillatoria nigro-viridis PCC711. Low temperature tolerant Arthrospira strains could broaden the areas suitable for cultivation, extend the seasonal cultivation time, and lower production costs.