Gel formation in mixtures of high amylopectin potato starch and potato starch

The effects of starch granules on the rheological behaviour of gels of native potato and high amylopectin potato (HAPP) starches have been studied with small deformation oscillatory rheometry. The influence of granule remnants on the rheological properties of samples treated at 90 °C was evident when compared with samples treated at 140 °C, where no granule remnants were found. The presence of amylose in native potato starch gave to stronger network formation since potato starch gave higher moduli values than HAPP, after both 90 and 140 °C treatments. In addition, amylose may have strengthened the network of HAPP because higher moduli values were obtained when native potato starch was added to the system. The moduli values of the mixtures also increased with increasing polysaccharide concentration in the system, which is due to an increment in the polysaccharide chain contacts and entanglements. Finally, it was found that a mixture of commercial amylose from potato starch and HAPP resulted in lower values of G′ compared to native potato starch. This indicates that the source of amylose is important for the properties in a blend with native amylopectin.     

Influence of sucrose on the rheology and granule size of cross-linked waxy maize starch dispersions heated at two temperatures

Cross-linked waxy maize (CWM) starch dispersions (STDs) of concentration 50 g kg⁻¹ were heated in sucrose solutions containing 0–600 g kg⁻¹ (g sucrose/kg dispersion) at 85 °C at low shear and in intermittently agitated cans at 110 °C. The STDs heated in 0–300 g kg⁻¹ sucrose exhibited antithixotropic behavior, while those heated in 400–600 g kg⁻¹ sucrose exhibited thixotropic behavior. The mean starch granule diameter of the starch dispersions did not show strong dependence on sucrose concentration. The dispersions, especially those with high sucrose concentrations and heated at 110 °C, exhibited G′ versus frequency (ω) profiles of gels. The STDs exhibited first normal stress differences that increased in magnitude with the concentration of sucrose. Values of the first normal stress coefficient of canned dispersions calculated from dynamic rheological data plotted against ω and experimental values plotted against shear rate of some of the STDs overlapped.     

Spherulitic crystallization of gelatinized maize starch and its fractions

Binary systems of polymers often display spherulitic morphologies after cooling from the melt, but these phenomena have rarely been reported among food polymers of native-size. Here we report the observation of spherulitic and other morphologies in gelatinized maize starch. The morphology could be manipulated by choosing polymer compositions and kinetic regimes. Spherulites (10 μm diameter) formed from gelatinized high-amylose maize starches and purified amylose at cooling rates of order of magnitude 100 °C/min. They were more numerous and exhibited a higher melting point the greater the ratio of amylose to amylopectin. Rapid cooling rates (150–500 °C/min) resulted in a more even distribution of smaller spherulites. Very rapid (liquid nitrogen quench) or slow (0.1–1 °C/min) cooling rates resulted in mixed morphology, as did addition of 15 or 60% (w/w) sucrose to a 10% (w/w) dispersion of high-amylose starch (HAS). Spherulites were observed in aqueous suspensions of high-amylose maize starch between 5 and 30% (w/w). Lower starch concentrations resulted in a broader size distribution and spherulites of more distinct shape. WAXS patterns of B-type were observed. Negatively birefringent spherulites predominated, but positive spherulites were found. The spherulite melting range overlapped with that for amylose–lipid complex. Evidence indicated that micro-phase separation takes place when a holding period at 95 °C follows gelatinization at 180 °C. Despite the high maximum temperature of treatment (180 °C) there was evidence for a memory effect in samples of 30% HAS. Spherulite morphology closely resembled that of native starch granules in very early stages of development.     

Effect of polymeric cosolutes on calcium pectinate gelation. Part 2. Dextrans and inulin

In a continuation of the work reported in the preceding paper, the effect of chicory root inulin (M_r≈4.5 kD) and branched dextrans of M_r 67, 464 and 2000 kD on gelation of low methoxy pectin (DE 31; 2.0 wt%; pH≈2.9–3.0) on cooling from 90 to 5 °C in the presence of stoichiometric Ca²⁺ has been characterised by low amplitude oscillatory measurements of G′ and G″. As found for other polymeric cosolutes studied previously (oxidised starch, potato maltodextrin, guar gum and locust bean gum), increasing concentrations of dextran or inulin caused a progressive increase of G′ and G″ in the solution state at 90 °C (attributed to segregative interactions promoting formation of calcium-mediated ‘egg-box’ junctions between pectin chains) and a progressive reduction in final moduli at 5 °C (attributed to excessive association of calcium pectinate into large aggregated bundles), with cooling curves crossing those for calcium pectinate alone at 55 °C. For the dextran samples, the ability to promote initial association of pectin chains at high temperature decreased with increasing molecular weight (i.e. with the smallest molecules having the greatest effect, as was also found for guar gum), but the reduction in final modulus on completion of cooling to 5 °C became more pronounced. By the criterion of the decrease in the change in log G′ during cooling, the three dextran samples studied seem roughly comparable in their overall effectiveness in promoting self-association of pectin, with inulin having a substantially smaller effect. Both materials, however, are less effective than the partially depolymerised starches and galactomannans studied previously. It is tentatively suggested that this may be associated with the flexibility introduced by the presence of three single bonds in the predominant glycosidic linkages of both dextran and inulin.     

Pumpkin pectin: gel formation at unusually low concentration

The gel properties of high-methoxy pectin from pumpkins have been investigated to assess the potential of this material as a hard-currency export from the former Soviet Union. Comparison was made with commercial slow-set, medium-set and rapid-set pectins from citrus peel. Gels were formed by cooling pectin solutions (pH 3·0; 60% (w/w) sucrose; 5% (w/w) corn syrup) from 95°C to 25°C, and the time-temperature course of network formation was monitored by small-deformation oscillatory measurements of storage modulus (G′). At concentrations above 1% (w/w) the pumpkin pectin gave weaker gels than the other three samples, but its minimum critical gelling concentration (c₀) was found to be much lower (by at least a factor of five). Compression testing gave similar results, with pumpkin pectin giving useful breaking-stress (‘hardness’) at concentrations down to 0·5% (w/w), about a factor of two lower than for the citrus samples. Its gelation was also less rapid, giving G′ values below those of the other three samples at temperatures down to 60°C, but then setting sharply; this behaviour could be useful in avoiding ‘pregelation’ in commercial processing. The commercial slow-set pectin showed typical ‘weak gel’ properties in the solution state at 95°C, with systematic reduction in gel-like character with increasing ester content in the other samples. The rigidity of the final gels also decreased systematically through the series: rapid-set < medium-set < slow-set. These observations are tentatively ascribed to stable association of unesterified galacturonate chain segments at low pH, where electrostatic repulsion is suppressed.     

Effect of water-soluble and insoluble non-starch polysaccharides isolated from wheat flour on the rheological properties of wheat starch gel

Water-soluble (WSP) and insoluble non-starch polysaccharides (WIP) were isolated from wheat flour to evaluate the effects of WSP and WIP on starch gel properties. Isolated WSP and WIP were added to two types of isolated wheat starch with different amylose content at a concentration of 3% based on the dry weight of starch. 30% starch gels were prepared and stored at 5 °C for 1, 8, or 24 h. The dynamic viscoelasticity of 30% starch gels mixed with WSP and WIP was measured using parallel plate geometry, showing that WSP and WIP affected the elastic component of starch gels in opposite ways. Adding WIP increased the storage shear modulus (G′) of starch gels, while adding WSP decreased G′ and dramatically increased the loss tangent (tan δ=G″/G′).     

Effect of heat–moisture treatment on the structure and physicochemical properties of tuber and root starches

Starch from tubers potato (Solanum tuberosum), taro (Alocassia indica), new cocoyam (Xanthosoma sagitifolium), true yam (Dioscorea alata), and root cassava, (Manihot esculenta) crops was isolated and its morphology, composition and physicochemical properties were investigated before and after heat–moisture treatment (HMT) (100 °C, for 10 h at a moisture content of 30%). Native starch granules were round to oval to polygonal with smooth surfaces. The granule size (diameter) ranged from 3.0 to 110 μm.The total amylose content ranged from 22.4 to 29.3%, of which 10.1–15.5% was complexed by native lipid. The phosphorus content ranged from 0.01 to 0.1%. The X-ray pattern of potato and true yam was of the ‘B’-type. Whereas, that of new cocoyam and taro was of the ‘A’-type. Cassava exhibited a mixed ‘A+B’-type X-ray pattern. The relative crystallinity, swelling factor (SF), amylose leaching (AML), gelatinization temperature range and the enthalpy of gelatinization of the native starches ranged from 30 to 46, 22 to 54, 5 to 23%, 13 to 19 °C and 12 to 18 J/g, respectively. Susceptibility of native starches towards hydrolysis by 2.2N HCl and porcine pancreatic -amylase were 60–86% (after 12 days), and 4–62% (after 72 h), respectively. Retrogradation was most pronounced in the B-type starches. Granule morphology remained unchanged after HMT. The X-ray pattern of the B-type starches was altered (B→A+B) on HMT. However, that of the other starches remained unchanged. HMT decreased SF, AML, gelatinization enthalpy and susceptibility towards acid hydrolysis, but increased gelatinization temperatures and enzyme susceptibility. Extent of retrogradation and relative crystallinity decreased on HMT of true yam and potato starches, but remained unchanged in the other starches. The foregoing data showed that changes in physicochemical properties on HMT are influenced by the interplay of crystallite disruption, starch chain associations and disruption of double helices in the amorphous regions.     

Gelatinization mechanism of potato starch

The non-Newtonian behavior and dynamic viscoelasticity of potato starch (Jaga kids red ’90, 21.0% amylose content) solutions after storage at 25 and 4°C for 24 h were measured with a rheogoniometer. The flow curves, at 25°C, of potato starch showed plastic behavior >1.0% (w/v) after heating at 100°C for 30 min. A gelatinization of potato starch occurred above 1.0% at room temperature. A very large dynamic viscoelasticity was observed when potato starch solution (3.0%) was stored at 4°C for 24 h and stayed at a constant value with increasing temperature. A small dynamic modulus of potato starch was observed upon addition of urea (4.0 M) at low temperature (0°C) even after storage at 25 and 4°C for 24 h. A small dynamic modulus was also observed in 0.05 M NaOH solution. Possible models of gelatinization and retrogradation mechanism of potato starch were proposed.     

Studies on isolation and characterization of starch from oat (Avena nuda) grains

Starch from AC Hill oat grains (Avena nuda) was isolated and some of the characteristics determined. The yield of starch was 23·4% on a whole grain basis. The shape of the granule was polyhedral to irregular, with granules 6–10 μm in diameter. Lipids were extracted by acid hydrolysis and by selective solvent extraction with chloroform-methanol 2:1 v/v (CM) at ambient temperature, followed by n-propanol-water 3:1 v/v (PW) at 90–100°C. The acid hydrolyzed extracts which represented the total starch lipids (TSL) was 1·13%. The free lipids in the CM extract (1% TSL) was 6·2%, whereas the free and bound lipids in the PW extracts was 93.0%. Neutral lipids formed the major lipid class in the CM and PW extracts. The monoacyl lipid content in both CM and PW extracts was 61·0%. The total amylose content was 19·4%, of which 13·9% was complexed by native lipids. X-ray diffraction was of the ‘A’ type. Oat starch differed from wheat starch in showing a higher swelling factor, decreased amylose leaching, coleaching of a branched starch component and amylose during the pasting process, higher peak viscosity and set-back, low gel rigidity, greater susceptibility towards acid hydrolysis, greater resistance to -amylase action and a higher freeze-thaw stability. Furthermore, in comparison to wheat starch, the amylose chains of oat starch appear to be more loosely arranged in the amorphous regions, whereas in crystalline regions, oat starch chains are more compactly packed. Lipid removal from oat and wheat starches decreased their swelling factor, peak viscosity, set-back, gelatinization temperatures, freeze-thaw stability and paste clarity (at pH > 4·0), and increased their thermal stability, amylose leaching, enthalpy of gelatinization, susceptibility towards -amylase and paste clarity (at pH < 4·0). The results also showed that the properties of AC Hill oat starch is not representative of oat starch in general.     

Effect of polymeric cosolutes on calcium pectinate gelation. Part 3. Gum arabic and overview

Addition of gum arabic (average M_r≈450 kDa; 0.5–2.0 wt%) to solutions of low methoxy pectin (DE 31; 2.0 wt%; pH≈2.9–3.0) with stoichiometric Ca²⁺ caused massive increases in G′ and G″ in the pre-gel state at 90 °C (attributed to segregative interactions promoting formation of calcium-mediated ‘egg-box’ junctions between pectin chains) but had little effect on the gels formed on cooling to 5 °C. This is in marked contrast to the behaviour of other polymeric cosolutes studied in the investigations reported in the two preceding papers, which caused large reductions in gel moduli (attributed to excessive association of calcium pectinate into large aggregated bundles); the difference is tentatively ascribed to strengthening of the calcium pectinate network by divalent counterions to the uronate residues in gum arabic. When the complication of cation exchange was eliminated by extensive dialysis of gum arabic against 100 mM Na⁺ and use of the final dialysate in preparation of mixtures with calcium pectinate, massive increases in G′ and G″ at high temperature were again observed, but with accompanying reductions in moduli at low temperature, which, at gum arabic concentrations above 1.0 wt%, arose from collapse of the developing calcium pectinate network during cooling. The tentative conclusion from this work, and from the two preceding papers, is that enthalpically unfavourable (segregative) interactions between low methoxy pectin and polymeric cosolutes can be relieved in two ways: (i) Ca²⁺-mediated self-association of pectin into compact ordered assemblies which occupy less of the total volume, and (ii) conformational rearrangement of the cosolute molecules to minimise segmental interactions with pectin; conformational rearrangement is inhibited by chain stiffness and by branching; thus polymeric cosolute molecules of limited flexibility are more effective in promoting self-association of pectin than more flexible molecules of comparable size, and branched molecules are more effective than linear chains of comparable stiffness.     

Viscoelastic properties of aqueous solutions of an exocellular polysaccharide from cyanobacteria

The viscoelastic properties of aqueous solutions of the exocellular polysaccharide of Cyanospira capsulata have been studied, over a wide range of polymer concentrations, using small deformation oscillatory, steady and transient shear methods. The viscoelastic spectra generally resemble those of an entangled network, although notable deviations can be observed in the low frequency dependence of G′ and G″. At higher polymer concentrations, the viscoelastic spectrum shows solid-like behaviour over a wide range of frequencies. The superposition of η^*(ω) and η( ) curves occurs only at low frequencies, at higher frequencies the slope of η^*(ω) is lower than that of η( ). By studying the time evolution of shear stress after the inception of a steady shear rate (stress overshoot), the recovery of non-linear properties after steady shearing flow is seen to occur after times of c. 10³ s (in the case of 1·1% w/v solutions).

The overall viscoelastic properties appear original in comparison with those of the two structurally limiting types of polysaccharide, the ‘ordered’ chain xanthan and the ‘random coil’ guar. A rationale for this ‘anomalous’ viscoelastic behaviour can be tentatively proposed in terms of flickering intermolecular cross-interactions between semi-flexible segments, which occur in addition to the usual topological constraints.     

Physicochemical properties of endosperm and pericarp starches during maize development

Endosperm starch and pericarp starch were isolated from maize (B73) kernels at different developmental stages. Starch granules, with small size (2–4 μm diameter), were first observed in the endosperm on 5 days after pollination (DAP). The size of endosperm-starch granules remained similar until 12DAP, but the number increased extensively. A substantial increase in granule size was observed from 14DAP (diameter 4–7 μm) to 30DAP (diameter10–23 μm). The size of starch granules on 30DAP is similar to that of the mature and dried endosperm-starch granules harvested on 45DAP. The starch content of the endosperm was little before 12DAP (less than 2%) and increased rapidly from 10.7% on 14DAP to 88.9% on 30DAP. The amylose content of the endosperm starch increased from 9.2% on 14DAP to 24.2% on 30DAP and 24.4% on 45DAP (mature and dried). The average amylopectin branch chain-length of the endosperm amylopectin increased from DP23.6 on 10DAP to DP26.9 on14DAP and then decreased to DP25.4 on 30DAP and DP24.9 on 45DAP. The onset gelatinization temperature of the endosperm starch increased from 61.3 °C on 8DAP to 69.0 °C on 14DAP and then decreased to 62.8 °C on 45DAP. The results indicated that the structure of endosperm starch was not synthesized consistently through the maturation of kernel. The pericarp starch, however, showed similar granule size, starch content, amylose content, amylopectin structure and thermal properties at different developmental stages of the kernel.     

Effect of water content on the gelatinisation temperature of sago starch

Differential scanning calorimetry (DSC) has been used to study gelatinisation phenomena of sago starch. Two endothermic transitions were observed for starch heated in the presence of a limited amount of water (starch/water=37–50%w/w). These transitions appear to be due to co-operative effects of water-mediated melting of starch crystallites, remaining crystallites and/or amylopectin crystallites. At a water content of 50%, evidence of M₁ endotherm was observed and 85°C represents the effective T_m at the end of melting of native sago starch. The effect of starch concentration on the shape of these two endotherms was studied for sago starch. The experimental data were treated thermodynamically by applying equations describing phase transition of semi-crystalline polymers. The T⁰_m value obtained by extrapolation to v₁=0 was 390.6 K for sago.     

Structure of potato starch pastes in the ageing process by the measurement of their dynamic moduli

The effect of ageing on the rheological properties of potato starch pastes was investigated by measurement of dynamic viscoelasticity. The value of the storage modulus (G′) increased rapidly with time for the first few hours, but attained equilibrium after a long period of ageing. The relation between the concentration and the storage modulus showed a c^1·6 dependence. The Avrami exponent (n) obtained in this study was 0·66 and deviated significantly from the value (n = 1), corresponding to rod-like growth of crystal. The rate of storage modulus increase decreased with increasing concentrations up to 10%, and at higher concentrations little or no increase was observed. In addition, the rate of storage modulus increase increased dramatically when the NaCl concentration was raised to levels of 0·01 or above. An even greater increase in rate occurs on addition of AlCl₃.     

Effect of acid–alcohol treatment on the molecular structure and physicochemical properties of maize and potato starches

The molecular structure and physicochemical properties of acid–alcohol treated maize and potato starches (0.36% HCl in methanol at 25 °C for 1–15 days) were investigated. The yields of the modified starches were ranging from 91 to 100%. The average granule size of modified starches decreased slightly. The solubility of starches increased with the increase of treatment time, and the pasting properties confirmed the high solubility of modified starches. The gelatinization temperatures and range of gelatinization increased with the increase of treatment time except T_o (onset temperature) of maize starch. Molecular structures of modified starches suggested the degradation of starches occurred mostly within the first 5 days of treatment, and degradation rate of potato starch was higher than maize starch both in amylopectin and in amylose. Maize starch was found less susceptible to acid–alcohol degradation than potato starch.     

Phase equilibria and gelation in gelatin/maltodextrin systems — Part IV: composition-dependence of mixed-gel moduli

The storage moduli (G′) of phase-separated co-gels formed by quench-cooling mixed solutions of gelatin and potato maltodextrin (Paselli SA-2 and SA-6) have been related quantitatively to the experimentally-determined concentration-dependence of G′ for the constituent polymers. Distribution of water between the phases was examined explicitly by using polymer blending laws to derive calculated moduli for gelatin-continuous and maltodextrin-continuous networks over the entire range of solvent partition. Allowance was made for the direct contribution of polymer chains, and for density differences between the phases, in calculating relative phase-volumes. The effect of gel formation prior to phase-separation was calculated using classical theory for network de-swelling. Good agreement with observed moduli for more than 30 gelatin/maltodextrin combinations was achieved using a single adjustable parameter, p (the ratio of solvent to polymer in the gelatin phase divided by the same ratio for the maltodextrin phase), with an optimum value of p ≈ 1·8 for both SA-6 and SA-2.     

Physico-chemical characterisation of sago starch

The physico-chemical characteristics of various sago starch samples from South East Asia were determined and compared to starches from other sources. X-ray diffraction studies showed that all the sago starches exhibited a C-type diffraction pattern. Scanning electron microscopy showed that they consist of oval granules with an average diameter around 30 μm. Proximate composition studies showed that the moisture content in the sago samples varied between 10.6% and 20.0%, ash between 0.06% and 0.43%, crude fat between 0.10% and 0.13%, fiber between 0.26% and 0.32% and crude protein between 0.19% and 0.25%. The amylose content varied between 24% and 31%. The percentage of amylose obtained by colourimetric determination agreed well with the values obtained by fractionation procedures and potentiometric titration. Intrinsic viscosities and weight average molecular weight were determined in 1M KOH. Intrinsic viscosity for amylose from sago starches varied between 310 and 460 ml/g while for amylopectin the values varied between 210 and 250 ml/g. The molecular weight for amylose was found to be in the range of 1.41×10⁶ to 2.23×10⁶ while for amylopectin it was in the range of 6.70×10⁶ to 9.23×10⁶. The gelatinisation temperature for the sago starches studied varied between 69.4°C and 70.1°C. The exponent ‘a’ in the Mark–Houwink equation and the exponent ‘’ in the equation R_g=kM was found to be 0.80 and 0.58, respectively for amylose separated from sago starch and these are indicative of a random coil conformation. Two types of pasting properties were observed. The first was characterised by a maximum consistency immediately followed by sharp decrease in consistency while the second type was characterised by a plateau when the maximum consistency was reached.     

Formation and crystallization of amylose–monoglyceride complex in a starch matrix

The formation of amylose–lipid complexes in a gelatinized potato starch matrix was investigated using potato starch and glycerol monopalmitin. These complexes exist in two forms, with the amounts of each of the forms being dependent on the temperatures and durations of the pre-treatments.

Differential scanning calorimetry (DSC) was used to analyze transition temperatures and melting enthalpies, and thereby determine the amount of the complexes in the samples. X-ray diffraction analysis was used to investigate their crystallinity.

In measurements with DSC, form I started to melt at 88.5°C, and form II at 112.9°C. When complex form II was preheated at 100 or 110°C, its melting point rose to 116.3 and 119.7°C, respectively, because of an annealing effect. The same phenomenon occurred with complex form I: when preheated at 90°C, its melting point rose to 96.8°C. The crystal formation of form II appeared to be slower when treated at 110°C than at 100°C. Their maximum melting enthalpies were reached after about 24 h and 4 h of preheating, respectively. In X-ray diffraction analyses, form II showed a V-pattern, but form I did not. This indicates that form II is more crystalline than form I. It was possible to transform form I into form II when it was heat treated, because form I was then partially or totally melted.

As a comparison, the charged substance cetyltrimethylammonium bromide created complex form I with amylose in the starch matrix, but not form II.     

Cross-linking of wheat starch and hydroxypropylated wheat starch in alkaline slurry with sodium trimetaphosphate

Wheat starch was cross-linked at 40 °C and pH 11.0 by slurrying the starch (30% solids) in a solution of sodium trimetaphosphate (STMP), sodium hydroxide, and sodium sulfate. The extent of cross-linking was determined by an increase in alkaline fluidity or by a decrease in alkaline clarity. Response surface analysis showed that cross-linking increased with increasing levels of STMP (0.5-1.5%, based on starch, bos) and sodium sulfate (0–4.0%, bos) over a reaction period of 120–720 min. A regression equation with first and second order terms showed that STMP and sodium sulfate concentrations and the reaction time accounted for 99% of the variability in alkaline fluidity. Wheat starch (37% slurry) was hydroxypropylated by reaction with propylene oxide (8%, bos) for 24h at 45 °C in alkali (pH 11.5) containing 16.0% sodium sulfate (bos). The hydroxypropylated (4.5wt%) wheat starch (DS 0.12-0.13) was not isolated but was cross-linked with STMP (0.1-0.5%, bos) over a 10–40 min reaction period. A comparison of pasting curves at pH 3.5 showed that some of the cross-links produced by STMP were less stable than those produced by phosphoryl chloride, indicating a low level of pyrophosphate as well as monophosphate cross-links. The less stable cross-links were diminished by changing reaction conditions with STMP.     

Change of granular and molecular structures of waxy maize and potato starches after treated in alcohols with or without hydrochloric acid

Starches from waxy maize and potato were treated in methanol and 2-propanol either with or without 0.36% hydrochloric acid at 65 °C for 1 h. The granule morphology, molecular structure and pasting properties of the starches were determined and the effects of treatments on the granule and molecular structures of starch were investigated. Starch treated in alcohols without acid showed loss of native order through the hilum of granules, and no obvious molecular degradation was found. However, acid–alcohol treated starch showed many cracks inside granules, and both waxy maize and potato starches showed obvious molecular degradation after treated. Furthermore, the amylose chains and long chains of amylopectin of starch were more easily degraded with acid–alcohol treatment. The pasting viscosity of acid–alcohol treated starches were also obviously less than that of their counterpart native starch and starch after alcohol treatment. The extent of degradation of molecules and the decrease of pasting viscosity on potato starch after acid–alcohol treated were more obvious than that of waxy maize starch. The result indicates that the degradation preferentially occur in the amorphous region when starch treated by acid–alcohol, and the degradation of starch molecules enhances the amorphous excretion and the occurrence of cracks inside the granules.