Influence of Dissolved Oxygen Levels on Production of l-Asparaginase and Prodigiosin by Serratia marcescens

The effect of dissolved oxygen concentrations on the behavior of Serratia marcescens and on yields of asparaginase and prodigiosin produced in shaken cultures and in a 55-liter stainless-steel fermentor was studied. A range of oxygen transfer rates was obtained in 500-ml Erlenmeyer flasks by using internal, stainless-steel baffles and by varying the volume of medium per flask, and in the fermentor by high speed agitation (375 rev/min) or low rates of aeration (1.5 volumes of air per volume of broth per min), or both. Dissolved oxygen levels in the fermentation medium were measured with a membrane-type electrode. Peak yields of asparaginase were obtained in unbaffled flasks (3.0 to 3.8 IU/ml) and in the fermentor (2.7 IU/ml) when the level of dissolved oxygen in the culture medium reached zero. A low rate of oxygen transfer was accomplished by limited aeration. Production of prodigiosin required a supply of dissolved oxygen that was obtainable in baffled flasks with a high rate of oxygen transfer and in the fermentor with a combination of high-speed agitation and low-rate aeration. The fermentation proceeded at a more rapid rate and changes in pH and cell populations were accelerated by maintaining high levels of dissolved oxygen in the growth medium.     

Model analysis of biological oxygen transfer enhancement in surface-aerated bioreactors

A model was developed to evaluate the effects of cells and surfactants on oxygen transfer in surface-aerated bioreactors. The model assumed the presence of serial layers of adsorbed surfactants and microorganisms directly adjacent to the gas-liquid interface due to their surface activities, followed by a stagnant liquid layer to account for the oxygen transfer resistance in the liquid phase. The interfacial surfactant film, although posing as an additional resistance, was found to have negligible effect on the oxygen transfer rate because of its extremely small thickness as compared to the cell monolayer and the stagnant liquid layer. On the other hand, cells affect oxygen transfer by two mechanisms: the biological enhancement due to the respiration of interfacial cells and the physical blocking resulting from the semipermeable nature of cell bodies. Due to the low specific oxygen uptake rates of the sludges, the two mechanisms were found to be of comparable importance in activated-sludge systems; the oxygen transfer enhancement factor, E, varied from about 0.97 to 1.10 depending on the operating conditions. The biological enhancement effect, however, predominated in fermentations of actively growing bacteria. At relatively low agitation speed (e. g., 300 rpm), the value of E could reach about 3 to 5 in fermentations with high cell concentrations. Effects of other operating variables, such as the agitation intensity, the oxygen content in the mixed liquor, and the bulk cell concentration, on biological oxygen transfer enhancement were also studied. (c) 1992 John Wiley & Sons, Inc.     

Experimental study of a ceramic microsparging aeration system in a pilot-scale animal cell culture

The oxygen supply of cell cultures with the aid of free gas bubbles is an efficient process strategy in pharmaceutical production. If the cell-damaging impact of gas bubbles is reduced, direct aeration becomes a practical solution with scale-up potential and comparatively high oxygen transfer rates. In this paper a microsparging aeration system made of porous ceramic was compared with bubble-free membrane aeration. The sparging system was used for the long-term cultivation of mammalian cells in 2- to 100-L scale bioreactors and produced bubble sizes of 100-500 microm in diameter. Using a scale of 2.5 and 30 L, a cell density of 2.6 x 10(6) cells/mL was attained. When a 100-L scale was used, a density of 1.1 x 10(6) cells/mL was achieved, whereas a comparable membrane-aerated system showed a cell density of 2.2 x 10(6) cells/mL. At relatively low agitation rates of less than 70 rpm in the sparged bioreactors, a homogeneous and constant oxygen concentration was kept in the medium. As a result of the different foam-forming tendency caused by the lower gas flow of the ceramic sparger compared to that of the standard aeration systems, we were able to develop an appropriate process control strategy. Furthermore, oxygen transfer measurements for the common stainless steel sparger and the ceramic sparger showed a 3-fold higher oxygen transfer coefficient for the ceramic sparger.     

Production of carbonyl reductase by Geotrichum candidum in a laboratory scale bioreactor

Fungal fermentation is very complex in nature due to its nonlinear relationship with the time, especially in batch culture. Growth and production of carbonyl reductase by Geotrichum candidum NCIM 980 have been studied in a laboratory scale stirred tank bioreactor at different pH (uncontrolled and controlled), agitation, aeration and dissolved oxygen concentration. The yield of the process has been calculated in terms of glucose consumed. Initial studies showed that fermenter grown cells have more than 15 times higher activity than that of the shake flask grown cells. The medium pH was found to have unspecific but significant influence on the enzyme productivity. However, at controlled pH 5.5 the specific enzyme activity was highest (306U/mg). Higher agitation had detrimental effect on the cell mass production. Dissolved oxygen concentration was maintained by automatic control of the agitation speed at an aeration rate of 0.6 volume per volume per minute (vvm). Optimization of glucose concentration yielded 21g/l cell mass with and 9.77x10(3)U carbonyl reductase activity/g glucose. Adaptation of different strategies for glucose feeding in the fermenter broth was helpful in increasing the process yield. Feeding of glucose at a continuous rate after 3h of cultivation yielded 0.97g cell mass/g glucose corresponding to 29.1g/l cell mass. Volumetric oxygen transfer coefficient (K(L)a) increased with the increasing of agitation rate.     

Influence of the intensity of oxygen mass transfer on the biosynthesis of amphotericin B

Influence of oxygen mass transfer intensity characterized by the rate of oxygen dissolution (S) and the agitation rate (n), as well as influence of dissolved oxygen concentration on the process of amphotericin B biosynthesis was studied. It was shown that S = 40 and 110 mg/l. min and n = 450 and 800 min-1 were respectively the lower and the upper levels of the optimal conditions by oxygen mass transfer during amphotericin B biosynthesis. When biosynthesis of amphotericin B was conducted under conditions of the optimal oxygen mass transfer, the dissolved oxygen concentration of about 12 to 15 per cent of the saturation level was critical for the culture respiration. Inhibition of the culture respiration and antibiotic synthesis was induced under conditions of increased oxygen mass transfer intensity (S greater than 110 mg/l. min and n greater than 800 min-1) by high intensity mechanical agitation of the fermentation broth. Under conditions of decreased oxygen mass transfer (S less than 40 mg/l. min and n = less than 450 min-1) it was induced by insufficient supply of oxygen to the culture. On the basis of the results it was shown possible to control the aeration and agitation conditions by the rate of oxygen uptake and dissolved oxygen concentration. The data should be considered in optimization of aeration and agitation conditions in biosynthesis of amphotericin B in large fermenters.     

Improved poly-ε-lysine biosynthesis using Streptomyces noursei NRRL 5126 by controlling dissolved oxygen during fermentation

The growth kinetics of Streptomyces noursei NRRL 5126 was investigated under different aeration and agitation combinations in a 5.0 l stirred tank fermenter. Poly-epsilon-lysine biosynthesis, cell mass formation, and glycerol utilization rates were affected markedly by both aeration and agitation. An agitation speed of 300 rpm and aeration rate at 2.0 vvm supported better yields of 1,622.81 mg/l with highest specific productivity of 15 mg/l.h. Fermentation kinetics performed under different aeration and agitation conditions showed poly- epsilon-lysine fermentation to be a growth-associated production. A constant DO at 40% in the growth phase and 20% in the production phase increased the poly-epsilon-lysine yield as well as cell mass to their maximum values of 1,992.35 mg/l and 20.73 g/l, respectively. The oxygen transfer rate (OTR), oxygen utilization rate (OUR), and specific oxygen uptake rates (qO2) in the fermentation broth increased in the growth phase and remained unchanged in the stationary phase.     

Biological responses of hybridoma cells to hydrodynamic shear in an agitated bioreactor.

Effects of long-term hydrodynamic shear on hybridoma cells were investigated in a 250-ml continuous stirred-tank reactor (CSTR). Cells grown at steady state were subjected to step changes in agitation rates. Cell viability, glucose consumption, and monoclonal antibody (MAb) production were determined at high agitation rates and compared with the control (100 rev min-1). Impeller tip speeds higher than 40 cm s-1 caused a significant drop in cell concentration and respiration activity, and increased lactate dehydrogenase (LDH) release to the culture medium. Also, high agitation speeds caused a decrease in MAb concentration and an increase in specific glucose consumption rate. The effects of dilution rate and serum concentration on the sensitivity of hybridoma cells to hydrodynamic shear were determined. Serum was found to protect the cells against shear damage and had a significant positive effect on hybridoma growth and MAb production. Shear damage on cells in CSTR was approximated to first-order kinetics. The death rate constant increased sharply at impeller tip speeds above 40 cm s-1.     

Performance of mammalian cell culture bioreactor with a new impeller design

To improve the oxygen transfer in a mammalian cell bioreactor, a new type of impeller consisting of a double-screen concentric cylindrical cage impeller (annular cage impeller in short) was designed and its mass transfer rate evaluated. This new impeller design increases the specific screen area, and the convective mass transfer rate through the annular cage was significantly increased. The oxygen transfer rates with the new impeller and the commercially available cell-lift impeller (CelliGen by New Brunswick Scientific Co.) were evaluated and their performance compared at various rates of aeration and agitation. The results showed that with the new impeller, the oxygen transfer rate was increased by 19% in water and 21% in cell-free culture medium supplemented with 10% horse serum, the total hybridoma cell concentration was increased to 3.4 x 10(7) cells/mL, and the IgG(1) subtype monoclonal antibody (MAb) product concentration was also increased to 512 mg/L in perfusion culture of murine hybridoma cell line 62'D3. These improvements in oxygen transfer rate, cell concentration, and MAb product concentration are all very significant. The mass transfer resistance in the cell-lift impeller system was found to be mainly due to the surface area of the single-screen cage impeller. The new annular cage impeller not only provided the increased surface area for convective oxygen transfer but also protected cells from hydrodynamic shear damage, thereby achieving a significant bioprocess improvement in terms of higher viable cell concentration, higher product concentration, and higher oxygen transfer rate in the mammalian cell bioreactor system.     

The use of flow cytometry to study the impact of fluid mechanical stress on Escherichia coli W3110 during continuous cultivation in an agitated bioreactor

Continuous culture fermentations of Escherichia coli W3110 have been carried out at controlled dissolved oxygen levels of 40% and 10% of saturation. Satisfactory and reproducible results were obtained. Agitation speeds of 400 and 1200 rpm at an aeration rate of 1 vvm have been used as well as an aeration rate of 3 vvm at 400 rpm. The upper levels of these variables represent much higher agitation and aeration intensities than those normally used in practical fermentations. The fermentations were monitored by mass spectrometry and optical density, and cell samples were studied by flow cytometry, SEM, and TEM. Protocols were developed so the state of both cell membranes and cell size could be measured by flow cytometry. Under all the conditions of agitation and aeration, flow cytometric analysis indicated that both cell membranes were intact and that a cytoplasmic membrane potential existed; also the cell size did not change, results confirmed by SEM and TEM. There were no detectable changes in off-gas analysis or optical density during the continuous fermentation nor in the cell structure as revealed by SEM or TEM, except at the highest agitation intensity. Under the latter conditions, after 7 h, the outer polysaccharide layer on the cell was stripped away. It is concluded that any changes in biological performance of this E. coli cell line due to variations in agitation or aeration intensity or scale of operation cannot be attributed to fluid dynamic stresses associated with the turbulence generated by impellers or with bursting bubbles.     

An oxygen supply strategy for the large-scale production of tissue plasminogen activator by microcarrier cell culture

An oxygen supply strategy involving agitation speed and aeration method for the large-scale production of tissue plasminogen activator (TPA) by a microcarrier cell culture was investigated by small-scale model experiments. A preliminary calculation indicated that diffusion limitation of dissolved oxygen (DO) could be caused in a microcarrier sedimentation layer more than 0.5 mm in thickness. Within an agitation speed range above 70 rpm, which was the critical speed for all of the microcarrier beads to remain suspended and thus for avoiding a deficiency of DO, the TPA productivity was higher at a lower agitation speed, while the cell concentration was not affected by the agitation speed. The addition of soluble starch to the culture medium prevented sedimentation of the microcarrier beads, even at the low agitation speed of 20 rpm, resulting in a TPA productivity higher than that at 70 rpm, which was the optimum speed without soluble starch. Use of an air spray system with an optimized air flow rate resulted in a k_La 2.35 times higher than that with simple surface aeration. Increasing the internal pressure of the culture from 0.2 kg/cm² (1209 hPa) to 1.5 kg/cm² (2483 hPa) had no effect on the cell growth but slightly increased the TPA production rates. However, based on the glucose consumption, both the cell and TPA yields were much improved by pressurization. As an optimum mixing and oxygen supply strategy for the production of TPA on a large scale, it is recommended that soluble starch be added to the culture medium to allow the microcarrier suspension to be maintained at a low agitation speed, while keeping a high oxygen transfer rate by means of an air spray system and pressurization.     

Trehalose accumulation from corn starch by Saccharomycopsis fibuligera A11 during 2-l fermentation and trehalose purification

In this study, corn starch was used as the substrate for cell growth and trehalose accumulation by Saccharomycopsis fibuligera A11. Effect of different aeration rates, agitation speeds, and concentrations of corn starch on direct conversion of corn starch to trehalose by S. fibuligera A11 were examined using a Biostat B2 2-l fermentor. We found that the optimal conditions for direct conversion of corn starch to trehalose by this yeast strain were that agitation speed was 200 rpm, aeration rate was 4.0 l/min, concentration of corn starch was 2.0% (w/v), initial pH was 5.5, fermentation temperature was 30°C. Under these conditions, over 22.9 g of trehalose per 100 g of cell dry weight was accumulated in the yeast cells, cell mass was 15.2 g/l of the fermentation medium, 0.12% (w/v) of reducing sugar, and 0.21% (w/v) of total sugar were left in the fermented medium within 48 h of the fermentation. It was found that trehalose in the yeast cells could be efficiently extracted by the hot distilled water (80°C). After isolation and purification, the crystal trehalose was obtained from the extract of the cells.     

Enhancement of glucose oxidase production in batch cultivation of recombinant Saccharomyces cerevisiae: optimization of oxygen transfer condition

AIMS: To obtain an optimal combination of agitation speed and aeration rate for maximization of specific glucose oxidase (GOD) production in recombinant Saccharomyces cerevisiae, and to establish a correlation between kLa vis-à-vis oxygen transfer condition and specific glucose oxidase production. METHODS AND RESULTS: The oxygen transfer condition was manifested indirectly by manipulating the impeller speed and aeration rate in accordance with a Central Composite Rotatory Design (CCRD). The dissolved oxygen concentration and the volumetric oxygen transfer coefficient (kLa) were determined at corresponding combinations of impeller speed and aeration rate. The maximal specific extracellular glucose oxidase production (3.17 U mg-1 dry cell mass) was achieved when the initial dissolved oxygen concentration was 6.83 mg l-1 at the impeller speed of 420 rev min-1 and at the rate of aeration of 0.25 vvm. It was found out that while impeller speed had a direct effect on the production of enzyme, a correlation between kLa and specific GOD production could not be established. CONCLUSION: At the agitation speed of 420 rev min-1 and at 0.25 vvm aeration rate, the degree of turbulence and the dissolved oxygen concentration were thought to be optimal both for cellular growth and production of enzyme. SIGNIFICANCE AND IMPACT OF THE STUDY: The combined effect of agitation and aeration on recombinant glucose oxidase production in batch cultivation has not yet been reported in the literature. Therefore, this study gives an insight into the effect of these two important physical parameters on recombinant protein production. It also suggests that since there is no correlation between kLa and specific production of GOD, kLa should not be used as one of the scale-up parameters.     

Homogenisation and oxygen transfer rates in large agitated and sparged animal cell bioreactors: Some implications for growth and production

Because of concern for cell damage, very low agitation energy inputs have been used in industrial animal cell bioreactors, typical values being two orders of magnitude less than those found in bacterial fermentations. Aeration rates are also very small. As a result, such bioreactors might be both poorly mixed and also unable to provide the higher oxygen up-take rates demanded by more intensive operation. This paper reports experimental studies both of K _L a and of mixing (via pH measurements) in bioreactors up to 8 m³ at Wellcome and of scaled down models of such reactors at Birmingham. Alongside these physical measurements, sensitivity of certain cell lines to continuously controlled dO₂ has been studied and the oxygen up-take rates measured in representative growth conditions. An analysis of characteristic times and mixing theory, together with other recent work showing that more vigorous agitation and aeration can be used especially in the presence of Pluronic F-68, indicates ways of improving their performance. pH gradients offer a special challenge.     

CcpA regulation of aerobic and respiration growth in Lactococcus lactis

The catabolic control protein CcpA is the highly conserved regulator of carbon metabolism in Gram-positive bacteria. We recently showed that Lactococcus lactis, a fermenting bacterium in the family of Streptococcaceae, is capable of respiration late in growth when haem is added to aerated cultures. As the start of respiration coincides with glucose depletion from the medium, we hypothesized that CcpA is involved in this metabolic switch and investigated its role in lactococcal growth under aeration and respiration conditions. Compared with modest changes observed in fermentation growth, inactivation of ccpA shifts metabolism to mixed acid fermentation under aeration conditions. This shift is due to a modification of the redox balance via derepression of NADH oxidase, which eliminates oxygen and decreases the NADH pool. CcpA also plays a decisive role in respiration metabolism. Haem addition to lag phase ccpA cells results in growth arrest and cell mortality. Toxicity is due to oxidative stress provoked by precocious haem uptake. We identify the repressor of the haem transport system and show that it is a target of CcpA activation. We propose that CcpA-mediated repression of haem uptake is a means of preventing oxidative damage at the start of exponential growth. CcpA thus appears to govern a regulatory network that coordinates oxygen, iron and carbon metabolism.     

Degradation of Benzene,Toluene and Xylene by Pseudomonas aeruginosa Engineered with the Vitreoscilla Hemoglobin Gene

This study concerns the potential use of Pseudomonas aeruginosa expressing the Vitreoscilla hemoglobin gene for the degradation of important harmful aromatic compounds such as benzene, toluene, and xylene (BTX). The use of these compounds by both strains was determined as the production of cell mass (viable cell number) in a minimal medium containing any one of the BTX compounds as the sole carbon and energy source. Furthermore, the BTX degradation capability of both strains was monitored by measuring the production of 3‐methylcatechol, a common intermediate. For the cells of the logarithmic phase, which were grown at high aeration/high agitation or low aeration/low agitation, the engineered strain showed a better growth rate than the host strain. With the benzene in the medium, the recombinant strain exhibited a higher (up to 4‐fold) cell density than the parental wild‐type strain at this phase. In contrast, regarding the cells of the late stationary phase under high aeration/high agitation conditions, the host strain had generally higher viable cell numbers than the recombinant strain. At this phase this difference was, however, less significant under the conditions of low aeration/low agitation. Similarly, in toluene containing medium (at high aeration/high agitation) the recombinant strain showed a higher cell density which was from a 15‐fold to almost one order of magnitude greater than its parental strain during the logarithmic phase where the cell density of P. aeruginosa remained nearly constant. Contrary to the results with benzene and toluene, both strains exhibited similar growth characteristics when they were grown in the presence of xylene. The positive effect of the oxygen uptake by the recombinant system on the BTX metabolizing activity was also apparent in a high accumulation of 3‐methylcatechol in the cultures of the recombinant strain. At certain points of incubation, the hemoglobin expressing strain showed a significantly (p < 0.05) higher 3‐methylcatechol accumulation than the host strain. These results demonstrated the possible potential of the Vitreoscilla hemoglobin as an efficient oxygen uptake system for the bioremediation of some compounds of environmental concern.     

Oxygen transfer kinetics of riboflavin fermentation by Ashbya gossypii in agitated fermentors

Effects of agitation and aeration rates on volumetric oxygen transfer coefficient and oxygen uptake rate of a riboflavin broth containing Ashbya gossypii were investigated in three batch, sparged, and agitated fermentors having the working volumes of 0.42, 0.85, and 2.5 l. The change of oxygen uptake rate with time at 250 rev min⁻¹ stirring and vvm aeration rates was shown. The volumetric oxygen transfer coefficients and maximum oxygen uptake rates obtained have been correlated to mechanical power inputs per unit volume of the fermentation broth and the superficial air velocities.     

A novel centrifugal impeller bioreactor. II. Oxygen transfer and power consumption

The effects of the impeller configuration, aeration rate, and agitation speed on oxygen transfer coefficient K(L)a were studied in a newly designed centrifugal impeller bioreactor (5-L). The oxygen transfer rates in the novel bioreactor were also compared with those in a cell-lift bioreactor with comparable dimensions. The cell-lift impeller produced much higher surface oxygen transfer rates than the centrifugal one at an agitation speed over 200 rpm. This result was in good agreement with our observation that the cell-lift impeller produced much higher unfavorable turbulence. In addition, the experiments using granulated agar particles as pseudo plant cells indicated that the K(L)a value decreased steadily with an increase in agar particle concentration, and the centrifugal impeller still demonstrated a larger K(L)a than the cell lift up to a high pseudo cell concentration of 19.5 g dry weight (DW)/L (under 150 rpm and 0.20 vvm) or 22.3 g DW/L (under 200 rpm and 0.20 vvm). Furthermore, the correlation between power number and impeller Reynolds number for both the centrifugal and the cell-lift impellers was successfully obtained, which could be used for predicting the power input required by each impeller. From the results obtained, the centrifugal impeller bioreactor is expected to have great potential in its application to shear-sensitive biological systems.     

Agitation induced cell injury in microcarrier cultures. Protective effect of viscosity is agitation intensity dependent: Experiments and modeling

The effect of medium viscosity on the specific death rate of bovine embryonic kidney (BEK) cells cultured in spinner flask microcarrier cultures has been examined for various impeller speeds. Two types of media were used, a serum-containing growth medium and a serum-free maintenance medium. The latter does not support cell growth. We found that increasing medium viscosity suppresses cell death rates in both growth and maintenance medium cultures in an agitation-intensity-dependent fashion; the beneficial effect of medium viscosity in reducing the specific death rate is amplified as the agitation rate is increased. Furthermore, increasing medium viscosity has no effect on the specific death rate of the cells when the agitation rate is below a critical level. A model based on the turbulent energy content of eddies in the dissipation spectrum of turbulence of length scales on the order of magnitude of the microcarrier diameter and lower has been developed to account for cell death due to both bead-to-bead and bead-to-eddy interactions. The model constitutes a significant departure from previous efforts first because both types of interactions are accounted for simultaneously and second because the properties of a spectrum of eddies instead of the Kolmogorov-scale eddy size alone are used in the model. The model explains the functional dependence of the specific death rates on the medium viscosity at varying agitation intensities.     

Effect of stirrer speed,aeration rate and cell mass concentration on volumetric oxygen transfer coefficients (KLa) in the cultivation of Curvularia lunata in a batch reactor

Summary Curvularia lunata was grown in a stirred and aerated reactor for the production of extracellular rifamycin oxidase. Volumetric oxygen transfer coefficients (K_La) were measured for various stirrer speeds, rates of aeration and cell mass concentrations in the reactor. Stirrer speed and aeration rate were optimized and it was found that stirrer speeds of 400–500 rpm and aeration rates of 0.75–1 vvm were optimum for the maximum amount of enzyme production. It was noticed that the increase in cell mass decreased the oxygen transfer coefficient. It was also noticed that the organism formed pellets rather than mycelia when grown on glucose and with an increase in the concentration of glucose in the reactor, there was heavy pellet formation.     

Redox driven metabolic tuning: carbon source and aeration affect synthesis of poly(3-hydroxybutyrate) in Escherichia coli

Growth and polymer synthesis were studied in a recombinant E. coli strain carrying phaBAC and phaP of Azotobacter sp. strain FA8 using different carbon sources and oxygen availability conditions. The results obtained with glucose or glycerol were completely different, demonstrating that the metabolic routes leading to the synthesis of the polymer when using glycerol do not respond to environmental conditions such as oxygen availability in the same way as they do when other substrates, such as glucose, are used. When cells were grown in a bioreactor using glucose the amount of polymer accumulated at low aeration was reduced by half when compared to high aeration, while glycerol cultures produced at low aeration almost twice the amount of polymer synthesized at the higher aeration condition. The synthesis of other metabolic products, such as ethanol, lactate, formate and acetate, were also affected by both the carbon source used and aeration conditions. In glucose cultures, lactate and formate production increased in low agitation compared to high agitation, while poly(3-hydroxybutyrate) synthesis decreased. In glycerol cultures, the amount of acids produced also increased when agitation was lowered, but carbon flow was mostly redirected towards ethanol and poly(3-hydroxybutyrate). These results indicated that carbon partitioning differed depending on both carbon source and oxygen availability, and that aeration conditions had different effects on the synthesis of the polymer and other metabolic products when glucose or glycerol were used.