A novel sensor based on electrochemical polymerization of diglycolic acid for determination of acetaminophen

Diglycolic acid (DA) polymer was coated on glassy carbon (GC) electrode by cyclic voltammetry (CV) technique for the first time. The electrochemical performances of the modified electrode were investigated by CV and electrochemical impedance (EIS). The obtained electrode showed an excellent electrocatalytic activity for the oxidation of acetaminophen (ACOP). A couple of well-defined reversible electrochemical redox peaks were observed on the ploy(DA)/GC electrode in ACOP solution. Compared with bare GC electrode, the oxidation peak potential of ACOP on ploy(DA)/GC electrode moved from 0.289 V to 0.220 V. Meanwhile, the oxidation peak current was much higher on the modified electrode than that on the bare GC electrode, indicating DA polymer modified electrode possessed excellent performance for the oxidation of ACOP. This kind of capability of the modified electrode can be enlisted for the highly sensitive and selective determination of ACOP. Under the optimized conditions, a wide linear range from 2 × 10(-8) to 5.0 × 10(-4)M with a correlation coefficient 0.9995 was obtained. The detection limit was 6.7 × 10(-9)M (at the ratio of signal to noise, S/N=3:1). The modified electrode also exhibited very good stability and reproducibility for the detection of ACOP. The established method was applied to the determination of ACOP in samples. An average recovery of 100.1% was achieved. These results indicated that this method was reliable for determining ACOP.     

Enrichment of electrochemically active bacteria using a three-electrode electrochemical cell

Electrochemically active bacteria were successfully enriched in an electrochemical cell using a positively poised working electrode. The positively poised working electrode (+0.7 V vs. Ag/AgCl) was used as an electron acceptor for enrichment and growth of electrochemically active bacteria. When activated sludge and synthetic wastewater were fed to the electrochemical cell, a gradual increase in amperometric current was observed. After a period of time in which the amperometric current was stabilized (generally 8 days), linear correlations between the amperometric signals from the electrochemical cell and added BOD (biochemical oxygen demand) concentrations were established. Cyclic voltammetry of the enriched electrode also showed prominent electrochemical activity. When the enriched electrodes were examined with electron microscopy and confocal scanning laser microscopy, a biofilm on the enriched electrode surface and bacterium-like particles were observed. These experimental results indicate that the electrochemical system in this study is a useful tool for the enrichment of an electrochemically active bacterial consortium and could be used as a novel microbial biosensor.     

Simultaneous determination of the monoamine neurotransmitters and glucose in rat brain by microdialysis sampling coupled with liquid chromatography-dual electrochemical detector

A new type of chemically modified electrode based ring-disk electrode as the dual electrochemical detector (DECD) for high-performance liquid chromatography (HPLC) to simultaneously determine the monoamine neurotransmitters and glucose is described. The ring electrode was modified with an ion-exchange polymer-overoxidized polypyrrole (OPPy) and the disk electrode was modified with nano Au colloid and glucose oxidase (GOD). The electrochemical behaviors of dopamine (DA) and ascorbic acid (AA) at the OPPy chemically modified electrode (CME) were investigated by differential pulse voltammetry (DPV). It was found that the CME could permeate dopamine cations and repelled the ascorbate anions, which could be used to determine the monoamine neurotransmitters and avoid the interference of AA. The electrochemical behavior of glucose at the Nafion/GOD-Au colloid/GC CME was investigated by amperometry and flow injection analysis (FIA). It was found that the sensitivity of the CME increased apparently in determination of glucose. In order to obtain better separation and current responses of the analytes in HPLC-DECD, several operational parameters have been investigated. Under the optimum conditions, the method showed good stability and reproducibility. The application of this method coupled with microdialysis sampling for in vivo simultaneous determination of monoamine neurotransmitters and glucose in rat brain was satisfactory.     

Simultaneous Determination of Oxidized and Reduced Forms of Plastoquinone A in Spinach Chloroplasts by High-Performance Liquid Chromatography with an Electrochemical Detector

A method for determination of the redox level of plastoquinoneA in spinach chloroplasts is described. Plastoquinone A andits reduced form plastoquinol A were extracted from chloroplastson a sample-preparation cartridge (SEP-PAK C₁₈ Cartridge, WatersAssoc. Inc.) with a mixture of ethanol and diethyl ether ( 1: 1, vv). Extracts were separated by reversed-phase high-performanceliquid chromatography and examined with an electrochemical detectorequipped with dual electrodes. Plastoquinone A was determinedby its reductive current on one electrode, and plastoquinolA by its oxidative current on the other electrode. This method was applied to the determination of the redox potentialof plastoquinone A in chloroplasts. The midpoint potential atpH 7.8 of plastoquinone A was +20 mV with an n number of 2. (Received March 30, 1987; Accepted August 3, 1987)     

A rapid competitive binding nonseparation electrochemical enzyme immunoassay (NEEIA) test strip for microcystin-LR (MCLR) determination

A competitive binding nonseparation electrochemical enzyme immunoassay (NEEIA) is described for the determination of microcystin-LR (MCLR) using a double-sided microporous gold electrode in cartridge-type cells. A gold film sputtered on one side of porous nylon membrane constitutes a working electrode, while another gold film formed on the opposite side serves as a pseudo reference electrode. After immobilizing MCLR antibody on working electrode by physical adsorption, the double-sided electrode was placed simply in a diffusion U-type or within a dry strip-type cell with a conjugate pad pre-loaded with a glucose oxidase labeled MCLR (GOx-MCLR) on working electrode side. Assays were performed in two steps: an MCLR-containing sample mixed with a known amount of GOx-MCLR conjugate either in buffer solution or in pre-loaded dry pad was incubated for an appropriate period (about 10 min) to induce competitive reaction with an immobilized anti-MCLR antibody on working electrode, and a fixed concentration of glucose solution (substrate) was then added to the backside of the working electrode. Due to the competitive nature of the assay, enzymatically generated product, hydrogen peroxide (H2O2), was detected at the working gold electrode (at +800 mV versus Au) by oxidation, and the magnitude of amperometric current was inversely proportional to the concentration of MCLR in the sample. The response time after substrate addition was about 30s. Mean recovery of MCLR added to tap water was 93.5%, with a coefficient of variation (CV) of 6.6%. The proposed competitive NEEIA system is in general comparable to existing heterogeneous enzyme immunoassays with a similar detection limit (100 pg/mL MCLR), and suitable for developing a disposable type biosensor for on-site monitoring of environment.     

A new assay method for hydrogenase based on an enzymic electrode reaction. The enzymic electric cell method.

A new assay method for hydrogenase [EC 1.12.2.1] based on the enzymic electrode reaction of H2-H+ equilibrium has been established. The method is based on the experimental fact that the short-circuit current of the electric cell composed of an electrode with hydrogenase and methylviologen as the mediator of H2-H+ equilibrium and a saturated calomel electrode as the counter electrode, is practically proportional to the amount of hydrogenase in the cell. The new method is referred to as the "enzymic electric cell method." This technique has applications not only to routine activity assay but also to the direct determination of the time course of enzyme denaturation, which has not previously been possible.     

A highly sensitive nanostructure-based electrochemical sensor for electrocatalytic determination of norepinephrine in the presence of acetaminophen and tryptophan

A new electrochemical sensor for the determination of norepinephrine (NE), acetaminophen (AC) and tryptophan (Trp) is described. The sensor is based on carbon paste electrode (CPE) modified with 3,4-dihydroxybenzaldehyde-2,4-dinitrophenylhydrazone (DDP) and takes the advantages of carbon nanotubes (CNTs), which makes the modified electrode highly sensitive for the electrochemical detection of these compounds. Cyclic voltammetry (CV) at various scan rates was used to investigate the redox properties of the modified electrode. The apparent charge transfer rate constant, k(s), and transfer coefficient, α, for electron transfer between DDP and CNT paste electrode were calculated. The mediated oxidation of NE at the modified electrode was investigated by CV and the values of k, α and diffusion coefficient (D) were calculated. Under the optimum pH of 7.0, the oxidation of NE occurs at a potential about 215 mV less positive than that of the unmodified CPE. Differential pulse voltammetry (DPV) of NE at the modified electrode exhibited two linear dynamic ranges with a detection limit (3σ) of 77±2 nM. DPV was used for simultaneous determination of NE, AC and Trp at the modified electrode, and quantitation of NE in some real samples by the standard addition method.     

Application of electrochemical properties of ordered mesoporous carbon to the determination of glutathione and cysteine

In this study, the electrochemical activity of ordered mesoporous carbon (OMC) was investigated and applied to the determination of glutathione (GSH) and cysteine (CySH). It has been demonstrated that the ordered mesostructure of OMC has an important role in the electrocatalytic activity towards thiols, and the destruction of this structure results in the decrease of such properties. The electrochemical behavior of GSH at an OMC electrode was also investigated. The results showed that the process of oxidation of GSH at the OMC electrode is differs from that of CySH at the same electrode by the peak at 0.47 V associated with CySH. This difference helped to reduce the interference of GSH during the determination of CySH in the presence of GSH. A sensor for the two thiols was developed with acceptable sensitivity and detection limits in a large determination range. These results obtained in the physiological medium and in the physiological levels of GSH and CySH, suggest that OMC is a promising material in the detection of thiols in biologically relevant experimental conditions (in terms of pH).     

Application of multivariate curve resolution alternating least squares method for determination of caffeic acid in the presence of catechin interference

In the current article, preparation and application of a graphene oxide nanosheets-based sensor for electrochemical determination of caffeic acid (CA) in the presence of catechin is described. This measurement was performed using the differential pulse voltammetry (DPV) technique and chemometric methods such as multivariate curve resolution–alternating least squares (MCR–ALS). The modified sensor was characterized by various techniques such as Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, ultraviolet–visible, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Operating conditions and influencing variables (involving several chemical and instrumental variables) were optimized with central composite rotatable design and response surface methodology. The second-order electrochemical data were generated by changing the pulse height in DPV, and after potential shift correction MCR–ALS was applied. Under the optimized conditions, the dynamic range for CA was from 0.5 to 100.0 μM and the detection limit was found to be 1.1 × 10^–9 M. The results revealed that the modified electrode shows an improvement in anodic oxidation activity of CA due to a marked enhancement in the current response compared with the bare carbon paste electrode. The modified electrode demonstrated good sensitivity, selectivity, and stability. The proposed method was successfully applied in determination of caffeic acid in the presence of unexpected electroactive interferences with a very high degree of overlapping such as catechin in real samples.     

Multispectral imaging of ion transport in neutral carrier-based cation-selective membranes.

BACKGROUND: High-resolution spectroscopic imaging of the cross section of ion-selective membranes during real-time electrochemical measurements is termed spectroelectrochemical microscopy (SpECM). SpECM is aimed for optimizing the experimental conditions in mass transport controlled ion-selective electrode (ISE) membranes for improved detection limit. METHODS: The SpECM measurements are performed in a thin layer electrochemical cell. The key element of the cell is a membrane strip spacer ring assembly which forms a two compartment electrochemical cell. The cell is placed onto the stage of a microscope and the membrane strip is positioned in the center of the field of view. A slice of the image is focused onto the entrance slit of the imaging spectrometer. RESULTS: SpECM has been used for the determination of the diffusion coefficients of different membrane ingredients and for the quantitative assessment of the charged site concentrations in ISE membranes and membrane plasticizers. In addition, changes in the concentration profiles of the ionophore (free and complexed) and charged mobile sites inside the ISE membranes are documented upon the application of large external voltages. CONCLUSIONS: This account demonstrates the power and advantages of SpECM, a multispectral imaging method for investigations of mass transport processes in ISE membranes during electrochemical measurements.     

Assay of enzymatic activity by electrochemical detection of reduced coenzyme.

A highly sensitive electrochemical assay of the enzymatic activities of aqueous samples of lactate dehydrogenase, alcohol dehydrogenase, and malate dehydrogenase has been developed using an improved amperometric determination of NADH concentration in the test solution. An anode current sensitivity of 750 μA/mmol of NADH was obtained with a platinum-mesh electrode in an H cell modified to permit vigorous stirring of the anolyte. Fouling of the platinum anode was significantly decreased by working at a pH ≥ 8.1. The rate of increase in net anode current in substrate solutions containing as little as 2 × 10⁻³ unit of enzyme/ml correlated well with the rate of change in absorbance at 340 nm for each sample. The reproducibility of the assay of enzyme activity was about ± 10%.     

Mediation of glycosylated and partially-deglycosylated glucose oxidase of Aspergillus niger by a ferrocene-derivatised detergent.

A ferrocene-derivatised detergent, (11-ferrocenylundecyl) trimethylammonium bromide (FTMAB), when oxidised to the corresponding ferricinium ion, was found by electrochemical studies to be an effective electron acceptor for reduced glucose oxidase of Aspergillus niger (EC 1.13.4) and thus acts as a electron-transfer mediator between glucose oxidase and a working electrode held at a potential sufficiently positive to reoxidise reduced FTMAB. An increase in mediating activity was produced when FTMAB was present in concentrations above its critical micelle concentration. An 'enzyme electrode' was formed by adsorption of glucose oxidase and FTMAB surfactant on a graphite rod. The electrode functioned as an amperometric biosensor for glucose in phosphate-buffered saline solution. A mixed micelle of glucose oxidase and FTMAB, probably adsorbed on the electrode surface, appears to be advantageous for the amperometric determination of glucose. Additionally, glucose oxidase was treated with alpha-mannosidase. When this partially-deglycosylated glucose oxidase was incorporated in an enzyme electrode, a 100-fold increase in the second-order rate constant (k) for electron transfer between the enzyme and FTMAB was observed, together with increased current densities, with respect to the equivalent values for FTMAB and commercial glucose oxidase. The use of deglycosylated enzymes in biosensors is suggested.     

Electrochemical immunosensor of platelet-derived growth factor with aptamer-primed polymerase amplification

A new method for the determination of platelet-derived growth factor BB (PDGF-BB) was developed using an electrochemical immunosensor with an aptamer-primed, long-strand circular detection probe. Rabbit anti-human PDGF-B polyclonal antibody was immobilized on the electrode to serve as the capture antibody. The detection probe was synthesized via polymerase extension along a single-stranded circular plasmid DNA template with a primer headed by the anti-PDGF-B aptamer. In the presence of the analyte, the aptamer-primed circular probe was captured on the electrode via the formation of an antibody/PDGF-BB/aptamer sandwiched complex. The electroactivity indicator methylene blue was adsorbed on the electrode surface via the analyte-sandwiched complex with long-strand circular DNA, thus yielding a strong electrochemical signal for the quantification of PDGF-BB. This strategy allowed electrochemical detection with enormous signal amplification arising from the long-strand localized circular probe. The oxidation peak current of methylene blue in square wave voltammetric measurements showed a linear dependence on the concentration of PDGF-BB in the range from 50 to 500 ng mL⁻¹, with a detection limit as low as18 pg mL⁻¹.     

Modified carbon paste electrodes for flow injection amperometric determination of isocitrate dehydrogenase activity in serum

A carbon paste electrode modified with the adsorbed products of the electrochemical oxidation of adenosine triphosphate is described. The electrode was applied to the amperometric electrocatalytic detection of the reduced form of both nicotinamide adenine dinucleotide and nicotinamide adenine dinucleotide phosphate. The catalytic oxidation current shows a linear dependence on the concentration of the reduced form of nicotinamide adenine dinucleotide up to 1x10(-4)M, with a detection limit of 5x10(-9)M. Modified carbon paste electrodes were coated with an electrogenerated film of nonconducting poly(o-phenylenediamine) to obtain a stable amperometric response for at least 150h. In addition to static measurements, determination of both reduced cofactors was carried out in a flow injection analysis system with a thin-layer amperometric detection cell. The electrocatalytic monitoring of reduced nicotinamide adenine dinucleotide phosphate was applied to flow injection measurement of isocitrate dehydrogenase activity in serum. The results were in good agreement with those for the standard spectrophotometric test kit. The proposed method consumed less time and reagents and provided better precision than the standard method.     

Electrochemical oxidation of purine and pyrimidine bases based on the boron-doped nanotubes modified electrode

Based on the excellent physicochemical properties of boron-doped carbon nanotubes (BCNTs), the electrochemical analysis of four free DNA bases at the BCNTs modified glassy carbon (GC) electrode was investigated. Herein, the BCNTs/GC electrode exhibited remarkable electrocatalytic activity towards the oxidation of purine bases (guanine (G), adenine (A)). More significantly, the direct oxidation of pyrimidine bases (thymine (T), cytosine (C)) was realized. It may be due to that BCNTs have the advantages of high electron transfer kinetics, large surface area, prominent antifouling ability and electrode activity. On basis of this, a novel and simple strategy for the determination of G, A, T and C was proposed. The BCNTs/GC electrode showed high sensitivity, wide linear range and capability of detection for the electrochemical determination of G, A, T, and C. On the other hand, the electrochemical oxidation of quaternary mixture of G, A, T, and C at the BCNTs/GC electrode was investigated. It was obtained that the peak separation between G and A, A and T, T and C were large enough for their potential recognition in mixture without any separation or pretreatment. The BCNTs/GC electrode also displayed good stability, reproducibility and excellent anti-interferent ability. Therefore, it can be believed that the BCNTs/GC electrode would provide a potential application for the electrochemical detection of DNA in the field of genetic-disease diagnosis.     

Selective glucose detection based on the concept of electrochemical depletion of electroactive species in diffusion layer

A glucose detection approach based on the concept of electrochemical depletion of electroactive species in diffusion layer was established, using scanning electrochemical microscopy (SECM). By controlling the glucose oxidase (GOD) modified electrode (substrate electrode) at a proper potential of electrochemical oxidation of interfering electroactive species, i.e., ascorbic acid (AA), an interference-free microcircumstance was formed in the diffusion layer of the substrate electrode. Consequently, we could successfully sense hydrogen peroxide generated from an enzymatic reaction by locating a Pt ultramicroelectrode (UME) (tip electrode, 5 microm in radius) into the diffusion layer of the substrate electrode. Properties of this interference-removing approach based on electrochemical depletion were systematically investigated. Results showed that the interference-removing efficiency was significantly determined by the tip-substrate distance and substrate potential. When the tip-substrate distance was 11 microm (2.2 times of the tip electrode radius) and the substrate potential was 0.5 V, nearly 90% of AA (0.5 mM) could be depleted within 30s without consumption of H2O2. Under these conditions, 0.1 mM AA showed no influence on the detection of 0.5 mM glucose. The linear range of glucose detection is 0.01-1 mM with a detection limit (DL) of 0.005 mM (correlation coefficient is 0.9948). This research will open a new way for developing selective micro-biosensors.     

Electrochemical regeneration of NAD in a plug-flow reactor

Electrochemical regeneration of NAD was performed at a laboratory preparative scale to illustrate both the efficiency and intrinsic simplicity of the electrochemical method. A powerful plug-flow reactor was realized with a flow through graphite felt electrode, the ratio of the effective area of electrode/volume of reactor increased to 380 cm(2)/cm(3). This graphite-felt electrode was able to oxidize NADH coenzyme at a very low overvoltage. On the example of the gluconic acid production catalyzed by glucose dehydrogenase, current as high as 0.1 A was obtained in experience where enzymatic activity was the main limitation. In confirmation of our previous work, the results show that the yield of NADH electrochemical oxidation is better than 99.95%.     

Internal standard method for the measurement of choline and acetylcholine by capillary electrophoresis with electrochemical detection

An internal standard method has been developed for the determination of the neurotransmitter acetylcholine and/or its metabolic precursor choline. This approach couples the high separation efficiency of capillary electrophoresis with the sensitivity and selectivity of electrochemical detection at an enzyme-modified electrode. Indirect electrochemical detection is accomplished at a 25 microm platinum electrode modified by cross-linking the enzymes choline oxidase and acetylcholinesterase with glutaraldehyde. Although in this simple form of electrode fabrication there is a gradual loss of response from the electrochemical detector with time, accurate quantitation is achieved by the addition of butyrylcholine, which is also a substrate for acetylcholinesterase, as an internal standard. A linear response is achieved between 0 and 125 microM with a limit of detection of 2 microM (25 fmol). The utility of this method was demonstrated by monitoring the kinetics of choline uptake in synaptosomal preparations.     

Determination of ascorbic acid in individual rat hepatocyte by capillary electrophoresis with electrochemical detection

A method for the direct determination of ascorbic acid (AA) in individual rat hepatocyte based on capillary electrophoresis (CE) coupled with electrochemical detection (ECD) using a new kind of homemade carbon fiber micro-disk bundle electrode has been described. Individual rat hepatocytes were injected into a fused-silica capillary with an inner diameter of 25 microm, and lysed by 0.1% sodium dodecylsulfate (SDS) as cell lysis solution. The following conditions were suitable for the determination of AA: running buffer, 1.83 x 10(-2) mol/l Na2HPO4-1.70 x 10(-3) mol/l NaH2PO4 (pH 7.8); separation voltage, 20.0 kV; detection potential, 0.80 V (vs. saturated calomel electrode (SCE)). The concentration limit of detection (LOD) of the method was 1.7 x 10(-6) mol/l at a signal-to-noise (S/N) ratio of 3, and the mass LOD was 3.0 fmol. The linear dynamic range was from 5.0 x 10(-6) to 5.0 x 10(-4) mol/l with a correlation coefficient of 0.9962 for the injection voltage of 5.0 kV and injection time of 10s. The relative standard deviation (R.S.D.) was 0.85% for the migration time and 1.8% for the peak current. This method was successfully applied to AA determination in rat hepatocyte. The recovery was between 91% and 97%, and the amount of AA in single rat hepatocyte ranged from 28 to 63 fmol.     

Direct voltammetry of catalase immobilized on silica sol-gel and cysteine modified gold electrode and its application

The direct voltammetry of catalase (CAT) immobilized in silica sol-gel film in the presence of cysteine on gold electrode was investigated. The CAT electrode showed a pair of well-defined and quasi-reversible cyclic voltammetry peaks. It can be used as an electrochemical biosensor for the determination of hydrogen peroxide. The calibration range of H(2)O(2) was from 1 to 30 micromolL(-1) and the detection limit was 0.4 micromolL(-1) at a signal-to-noise ratio of 3. The interaction of CAT and aluminum ion was also investigated based on the CAT-modified electrode. The electrochemical activity of the CAT-modified electrode was increased with the addition of Al(3+). The experimental results of voltammetry and fluorescence spectroscopy indicated that the conformation of CAT molecule was altered by the formation of Al-CAT complex with Al(3+), which may influence the activity of CAT.