Conducting polymer based fluorescence quenching as a new approach to increase the selectivity of immunosensors

Polypyrrole (Ppy) has been shown to be a superior matrix for fluorescence detection based immunosensors: (i) the fluorescence of polypyrrole and polypyrrole modified by entrapped proteins was almost not detectable when this polymer was excited by near UV 325 nm light; (ii) polypyrrole quenched the fluorescence of such fluorescence agents as fluoresceine 5(6)-isothiocyanate, rhodamine B and enzyme-horseradish peroxidase (HRP) by almost 100% if they were deposited in the solution as a drop at the Ppy surface followed by evaporation of the solvent. According to our knowledge, this work is first application of Ppy in the design of a fluorescence-based immunosensor, where low Ppy fluorescence background and Ppy induced fluorescence quenching were exploited. These sensors were devoted to the detection of antibodies against bovine leukemia virus (BLV) protein gp51 (anti-gp51-Ab). A biological recognition system of this fluorescence immunosensor model was based on polypyrrole with entrapped BLV proteins gp51 (gp51/Ppy). This gp51/Ppy layer was applied for the detection of anti-gp51-Ab. Secondary antibodies against anti-gp51-Ab labeled with HRP (Ab*) were applied as fluorescence-detectable labels that are able to recognize specifically and interact with the complex of gp51 proteins and anti-gp51-Ab antibodies (gp51/anti-gp51-Ab). It was demonstrated that fluorescence of non-specifically adsorbed Ab* was almost completely quenched by the Ppy substrate. In addition, enzymatic activity of HRP was exploited as a traditional reference method for verification of the formation of the immune complex gp51/anti-gp51-Ab/Ab*.     

Molecularly imprinted polymers (MIP) in electroanalysis of proteins

The review summarizes current knowledge on the main approaches used for creation of high affinity polymer analogs of antibodies (known as molecularly imprinted polymers, MIP) applicable for electroanalysis of functionally important proteins such as myoglobin, troponin T, albumin, ferritin, lysozyme, calmodulin. The main types of monomers for MIP preparation as well as methods convenient for analysis of MIP/protein interactions, such as surface plasmon resonance (SPR), nanogravimetry with the use of a quartz crystal resonator (QCM), spectral and electrochemical methods have been considered. Special attention is paid to experimental data on electrochemical registration of myoglobin by means of o-phenylenediaminebased MIP electrodes. It was shown that the imprinting factor calculated as a ratio of the myoglobin signal obtained after myoglobin insertion in MIP to the myoglobin signal obtained after myoglobin insertion in the polymer lacking the molecular template (NIP) is 2–4.     

Molecularly imprinted polymer diffraction grating as label-free optical bio(mimetic)sensor

Micropatterned molecularly imprinted polymer (MIP) transmissive 2D diffraction gratings (DGs) are fabricated and evaluated as label-free antibiotic bio(mimetic)sensors. Polymeric gratings are prepared by using microtransfer molding based on SiO(2)/Si molds. The morphology of the MIP gratings is studied by optical and atomic force microscopes. MIP 2D-DGs exhibit 2D optical diffraction patterns, and measurement of changes in diffraction efficiency is used as sensor response. The refractive index of the micropatterned MIP material was estimated, via solvent index matching experiments, to be 1.486. Immersion of a MIP 2D-DG in different solutions of target-antibiotic enrofloxacin leads to significant variations in diffraction efficiency, demonstrating target-molecule detection. On the other hand, no significant response is observed for both control experiments: MIP grating exposed to a non-retained analyte and an equivalent non-imprinted polymer grating exposed to the target analyte, showing highly specific antibiotic label-free optical recognition.     

Sensing HIV related protein using epitope imprinted hydrophilic polymer coated quartz crystal microbalance

We have developed a biomimetic sensor for the detection of human immunodeficiency virus type 1 (HIV-1) related protein (glycoprotein 41, gp41) based on epitope imprinting technique. gp41 is the transmembrane protein of HIV-1 and plays an important role in membrane fusion between viruses and infected cells. It is an important index for determining the extent of HIV-1 disease progression and the efficacy of therapeutic intervention. In this work, dopamine was used as the functional monomer and polymerized on the surface of quartz crystal microbalance (QCM) chip in the presence of template, a synthetic peptide with 35 amino acid residues, analogous to residues 579-613 of the gp41. This process resulted in grafting a hydrophilic molecularly imprinted polymer (MIP) film on the QCM chip. QCM measurement showed that the resulting MIP film not only had a great affinity towards the template peptide, but also could bind the corresponding gp41 protein specifically. The dissociation constant (K(d)) of MIP for the template peptide was calculated to be 3.17 nM through Scatchard analysis, which was similar to those of monoclonal antibodies. Direct detection of the gp41 was achieved quantitatively using the resulting MIP-based biomimetic sensor. The detection limit of gp41 was 2 ng/mL, which was comparable to the reported ELISA method. In addition, the practical analytical performance of the sensor was examined by evaluating the detection of gp41 in human urine samples with satisfactory results.     

Molecularly imprinted monolithic stationary phases for liquid chromatographic separation of tryptophan andN-CBZ-phenylalanine enantiomers

Monolithic molecularly imprinted columns were designed and prepared by anin-situ thermal-initiated copolymerization technique for rapid separation of tryptophan andN-CBZ-phenylalanine enantiomers. The influence of polymerization conditions and separation conditions on the specific molecular recognition ability for enantiomers and diastereomers was investigated. The specious molecular recognition was found to be dependent on the stereo structures and the arrangement of functional groups of the imprinted molecule and the cavities in the molecularly imprinted polymer (MIP). Moreover, hydrogen bonding interactions and hydrophobic interactions played an important role in the retention and separation. Compared to conventional MIP preparation procedures, the present method is very simple, and its macroporous structure has excellent separation properties.     

Combinatorial screening of polymer precursors for preparation of benzo[α] pyrene imprinted polymer: an ab initio computational approach

A combinatorial screening procedure was used for the selection of polymer precursors in the preparation of molecularly imprinted polymer (MIP), which is useful in the detection of the air pollution marker molecule benzo[a]pyrene (BAP). Molecular imprinting is a technique for the preparation of polymer materials with specific molecular recognition receptors. The preparation of imprinted polymers requires polymer precursors such as functional monomer, cross-linking monomer, solvent, an initiator of polymerization and thermal or UV radiation. A virtual library of functional monomers was prepared based on interaction binding scores computed using HyperChem Release 8.0 software. Initially, the possible minimum energy conformation of the monomers and BAP were optimized using the semi-empirical (PM3) quantum method. The binding energy between the functional monomer and the template (BAP) was computed using the Hartree-Fock (HF) method with 6-31 G basis set, which is an ab initio approach based on Moller-Plesset second order perturbation theory (MP2). From the computations, methacrylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA) were selected for preparation of BAP imprinted polymer. The larger interaction energy (ΔE) represents possibility of more affinity binding sites formation in the polymer, which provides high binding capacity. The theoretical predictions were complimented through adsorption experiments. There is a good agreement between experimental binding results and theoretical computations, which provides further evidence of the validity of the usefulness of computational screening procedures in the selection of appropriate MIP precursors in an experiment-free way.     

Electrochemical and piezoelectric monitoring of taurine via electropolymerized molecularly imprinted films

A molecularly imprinted electrochemical quartz crystal microbalance (EQCM) sensor is fabricated here for taurine, a β ‐amino acid significant for functioning of almost all vital organs. The polymeric film of l ‐methionine was electrochemically deposited on gold‐coated EQCM electrode. Experimental parameters were optimized for controlling the performance of molecularly imprinted polymer (MIP)‐modified sensor such as ratio of monomer and template, number of electropolymerization cycles, mass deposited in each cycle, and pH. Thus, fabricated MIP‐EQCM sensor was successfully applied for estimation of taurine in solutions with varying matrices, such as aqueous, human blood plasma, milk from cow, buffalo, and milk powder. Under optimized parameters, response of MIP sensor to taurine was linearly proportional to its concentration with limit of detection as 0.12μM. Hence, a highly sensitive and selective piezoelectric sensor for taurine has been reported here via imprinting approach.     

Molecularly imprinted polymer-assisted sample clean-up of ochratoxin A from red wine: merits and limitations

A new analytical method for the determination of the carcinogenic mycotoxin ochratoxin A (OTA) in red wines has been developed involving a two-dimensional solid-phase extraction (SPE) clean-up protocol on C18-silica and a target-selective molecularly imprinted polymer (MIP). Prior removal of the interfering acidic matrix compounds by C18 solid-phase extraction was crucial for a successful clean-up as direct sample loading onto the MIP led to poor recoveries. The combined solid-phase extraction protocol afforded extracts suitable for sensitive ochratoxin A quantification by HPLC-fluorescence detection. Preliminary validation of the method performance with spiked (0.033-1.0 ng OTA/ml) and commercial red wines provided recoveries >90% and < 10%, with limit of detection (LOD) and limit of quantification (LOQ) of 0.01 and 0.033 ng/ml. However, a similarly favorable performance characteristics was observed in control experiments in which the MIP was replaced by the corresponding non-imprinted polymer (NIP). These findings provide evidence that under the employed experimental conditions specific analyte binding to imprinted binding sites plays a minor role in selective OTA retention. In the framework of this study, other problems inherent to MIP-based solid-phase extraction have been addressed. These include the reproducible preparation of MIP materials with consistent molecular recognition characteristics, the potential for repeated use of MIP, unfavorable polymer swelling in application-relevant solvents, potential sample contamination by template bleeding, and slow analyte binding kinetics.     

Quartz crystal microbalance for the determination of daminozide using molecularly imprinted polymers as recognition element

As the daminozide (DM) and its metabolite have been identified to be potentially carcinogenic, rapid detection method for them is necessary for food safety. A type of piezoelectric crystal sensor has been prepared by using a molecularly imprinted polymer (MIP) as recognition element. The molecularly imprinted polymer was prepared by hot-induced precipitation polymerization, and then the polymer particles were fixed on the surface of the electrode. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to evaluate the obtained imprinted polymer particles and the MIP sensitive film coated on the electrode. The results showed that a typical time-response curve of the MIP-coated crystal to the DM solution had been given, frequency shifts versus logarithm changes of DM showed good linear correlation within the concentration range of 1.0x10(-9) to 10(-6) mg/mL (y=11.38 lg x+115.45, r=0.9872) and 1.0x10(-6) to 10(-1) mg/mL (y=25.22lgx+209.44, r=0.9938), respectively. The detection limit was 5.0x10(-8) mg/mL (S/N=3), which is lower than that of conventional methods. Further, computer simulation technology was employed to investigate the interaction between methacrylic acid and DM for elucidating the recognition mechanism. The influencing factor pH has also been investigated. The injection experiments of DM structurally related compounds indicated that the obtained sensor has high sensitivity, excellent selectivity, low cost, good reproducibility, and reusable property by combining with piezoelectric crystal and molecularly imprinted polymer.     

Amperometric immunosensor for diagnosis of BLV infection

A new amperometric immunosensor for detection of antibodies against bovine leukemia protein (gp51) was designed. The detection of antibody-antigen complex formation was based on application of secondary antibodies labeled with horseradish peroxidase (HRP). Ferrocenecarboxylic acid (FCA) and N,N,N',N'-tetramethylbenzidine (TMB) were selected as suitable mediators for this immunosensor. Optimal conditions for amperometric detection were found. Sensitivity of created system was compared with the results of enzyme-linked immunosorbent assay (ELISA) and agar gel immunodiffusion (AGID) reaction, and was sufficient for detection of usual anti-gp51 antibody concentration present in the blood serum of BLV-infected cattle.     

Investigation of the nature of MIP recognition: the development and characterisation of a MIP for Ibuprofen

This paper describes the rational design, generation and testing of a molecularly imprinted polymer specific for Ibuprofen. Ibuprofen is a member of the class of drugs termed non-steroidal anti-inflammatory drugs (NSAIDS). In the present study, Ibuprofen was used as a template molecule for the preparation of molecularly imprinted polymers. A MIP has been produced which is capable of recognising Ibuprofen in aqueous media. Furthermore, Ibuprofen can be selectively extracted from aqueous conditions by molecularly imprinted solid phase extraction (MISPE). Recoveries were typically high (>80%) and good selectivity for Ibuprofen over structurally related analogues was seen. Moreover, the nature of the recognition between MIP and template has been investigated by NMR and molecular modelling to analyse whether or not it is possible to predict how well a given MIP will perform under set conditions. In addition, the physical characteristics of the MIP have been investigated including the particle size distribution on exposure of the MIP to different solvents. This has been related to the ability of the MIP to rebind Ibuprofen under the same conditions. The data from the characterisation of the MIP has been used to further enhance the understanding of the nature of MIP recognition.     

‘Bite-and-Switch’ approach using computationally designed molecularly imprinted polymers for sensing of creatinine

A method for the selective detection of creatinine is reported, which is based on the reaction between polymerised hemithioacetal, formed by allyl mercaptan, o-phthalic aldehyde, and primary amine leading to the formation of fluorescent isoindole complex. This method has been demonstrated previously for the detection of creatine using creatine-imprinted molecularly imprinted polymers (MIPs) Since MIPs created using traditional methods were unable to differentiate between creatine and creatinine, a new approach to the rational design of a molecularly imprinted polymer (MIP) selective for creatinine was developed using computer simulation. A virtual library of functional monomers was assigned and screened against the target molecule, creatinine, using molecular modelling software. The monomers giving the highest binding score were further tested using simulated annealing in order to mimic the complexation of the functional monomers with template in the monomer mixture. The result of this simulation gave an optimised MIP composition. The computationally designed polymer demonstrated superior selectivity in comparison to the polymer prepared using traditional approach, a detection limit of 25 μM and good stability. The ‘Bite-and-Switch’ approach combined with molecular imprinting can be used for the design of assays and sensors, selective for amino containing substances.     

Towards the rational development of molecularly imprinted polymers: 1H NMR studies on hydrophobicity and ion-pair interactions as driving forces for selectivity

The preparation of molecularly imprinted polymers (MIP) based on non-covalent interactions has become a widely used technique for creating highly specific sorbent materials predominantly used in separation chemistry. A crucial factor in a successful imprinting protocol is the optimisation of the template/functional monomer interaction in the pre-polymerisation mixture, eventually leading to a maximum of high-affinity binding sites in the resulting polymer matrix. In order to develop more efficient preparation technologies for imprinted polymers, two separate pre-polymerisation complexes were investigated by NMR spectroscopic techniques in order to identify the types of interactions occurring in the pre-polymerisation mixture, and their implications for the subsequently formed imprinted polymer. In particular, hydrophobic effects have been followed by NMR spectroscopy and their contribution to the selectivity of the resulting MIP has been investigated. The 2,4-D imprint system is used as an example to fundamentally study whether observations at the pre-polymerisation stage correlate with properties of the finally prepared MIP, and which parameters govern success of an imprinting protocol.     

Synthesis and evaluation of a selective molecularly imprinted polymer for the contraceptive drug levonorgestrel

A molecularly imprinted polymer (MIP) has been prepared using levonorgestrel (LEV) as template. The polymer was synthesised in a non-covalent approach using methacrylic acid (MAA) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as cross-linking monomer via a free radical polymerization. An equivalent blank polymer was also synthesised in the absence of the template compound. Batch adsorption experiments were used to evaluate the binding affinity of the imprinted polymer. After packing MIP into a stainless steel column (150 mm x 4.6 mm i.d.), retention and elution of the template and related compounds were evaluated by high-performance liquid chromatography (HPLC). This LEV imprinted polymer was further applied for selective solid phase extraction (SPE) of LEV from human serum. It was confirmed that the binding ability of the prepared MIP for LEV was essentially sufficient in the presence of other compounds coexisting in serum sample. Therefore, as a selective and efficient solid phase material, LEV imprinted polymer has a high potential application in analysis of this steroidal hormone in clinical purposes.     

Class-specific molecularly imprinted polymers for the selective extraction and determination of sulfonylurea herbicides in maize samples by high-performance liquid chromatography–tandem mass spectrometry

A novel method based on the molecularly imprinted solid-phase extraction (MISPE) procedure has been developed for the simultaneous determination of concentrations of sulfonylurea herbicides such as chlorsulfuron (CS), monosulfuron (MNS), and thifensulfuron methyl (TFM) in maize samples by liquid chromatography–tandem quadrupole mass spectrometry (LC–MS/MS). The molecularly imprinted polymer (MIP) for sulfonylurea herbicides was synthesized by precipitation polymerization using chlorsulfuron as the template molecule, 2-(diethylamino)ethyl methacrylate (DEAMA) as the functional monomer, and trimethylolpropane trimethacrylate (TRIM) as the cross-linker. The selectivities of the chlorsulfuron template and its analogs on the molecularly imprinted polymer were evaluated by high-performance liquid chromatography (HPLC). The extraction and purification procedures for the solid-phase extraction (SPE) cartridge with a molecularly imprinted polymer as the adsorbent for the selected sulfonylurea herbicides were then established. A molecularly imprinted solid-phase extraction method followed by high-performance liquid chromatography–tandem mass spectrometry for the determination of chlorsulfuron, monosulfuron, and thifensulfuron methyl was also established. The mean recoveries of these compounds in maize were in the range 75–110% and the limits of detection (LOD) of chlorsulfuron, monosulfuron, and thifensulfuron methyl were 0.02, 0.75, and 1.45 μg kg⁻¹, respectively. It was demonstrated that the MISPE–HPLC–MS/MS method could be applied to the determination of chlorsulfuron, monosulfuron, and thifensulfuron methyl in maize samples.     

Selective solid-phase extraction using molecularly imprinted polymer for analysis of methamidophos in water and soil samples

An analytical methodology for the analysis of methamidophos in water and soil samples incorporating a molecularly imprinted solid-phase extraction process using methamidophos-imprinted polymer was developed. Binding study demonstrated that the polymer exhibited excellent affinity and high selectivity to the methamidophos. Evidence was also found by FT-IR analysis that hydrogen bonding between the CO(2)H in the polymer cavities and the NH(2) and P=O of the template was the origin of methamidophos recognition. The use of molecularly imprinted solid-phase extraction improved the accuracy and precision of the GC method and lowered the limit of detection. The recovery of methamidophos extracted from a 10.0 g soil sample at the 100 ng/g spike level was 95.4%. The limit of detection was 3.8 ng/g. The recovery of methamidophos extracted from 100 mL tap and river water at 1 ng/mL spike level was 96.1% and 95.8%, and the limits of detection were 10 and 13 ng/L respectively. These molecularly imprinted solid-phase extraction procedures enabled selective extraction of polar methamidophos successfully from water and soil samples, demonstrating the potential of molecularly imprinted solid-phase extraction for rapid, selective, and cost-effective sample pretreatment.     

Molecularly imprinted polymer of 5-methyluridine for solid-phase extraction of pyrimidine nucleoside cancer markers in urine

Normal and modified urinary nucleosides represent potential biomarkers for cancer diagnosis. To selectively extract modified nucleosides, we developed a molecularly imprinted polymer (MIP) of 5-methyluridine as selective material for molecularly imprinted solid-phase extraction (MISPE). The MIPs were obtained from vinyl-phenylboronate ester derivative of the template, acrylamide and pentaerythritol triacrylate co-polymer, and were tested in batch and cartridge experiments with aqueous samples. Our results indicated that the imprinted polymer was selective for pyrimidine nucleosides with a K(d) and a B(max) of 46 microM and 18 micromol/g, respectively. Finally, a MISPE of the most common pyrimidine nucleoside cancer markers in urine sample was realized.     

Displacement imprinted polymer receptor analysis (DIPRA) for chlorophenolic contaminants in drinking water and packaging materials

The preparation of a molecularly imprinted polymer (MIP) for pentachlorophenol is described together with two alternative reporter derivatives for use in a displacement imprinted polymer receptor analysis (DIPRA) format procedure. In this procedure, alternative reporter molecules were rebound to the synthetic receptor sites and their displacement by the target analyte was employed as the basis of a simple procedure for the measurement of chlorophenols in water and packaging material samples. Water samples were extracted using the standard procedure (EPA 528) and a detection limit of 0.5 microg l(-1) was achieved using the DIPRA detection method, with good agreement between the displacement technique and GC-ECD analysis. A variety of packaging materials, extracted using a buffered detergent solution were also analysed using the DIPRA procedure and showed good agreement with GC results. In addition, investigation of the cross-reactivity of a range of pesticides and materials commonly encountered in environmental analysis indicated the procedure gave good discrimination between pesticides bearing a chlorophenolic moiety and other materials. The procedure is considered highly suitable for use as a rapid field-test method or for incorporation into a test kit device.     

Solid-phase extraction of tramadol from plasma and urine samples using a novel water-compatible molecularly imprinted polymer

In this study, a novel method is described for the determination of tramadol in biological fluids using molecularly imprinted solid-phase extraction (MISPE) as the sample clean-up technique combined with high-performance liquid chromatography (HPLC). The water-compatible molecularly imprinted polymers (MIPs) were prepared using methacrylic acid as functional monomer, ethylene glycol dimethacrylate as cross-linker, chloroform as porogen and tramadol as template molecule. The novel imprinted polymer was used as a solid-phase extraction (SPE) sorbent for the extraction of tramadol from human plasma and urine. Various parameters affecting the extraction efficiency of the polymer have been evaluated. The optimal conditions for the MIP cartridges were studied. The MIP selectivity was evaluated by checking several substances with similar molecular structures to that of tramadol. The limit of detection (LOD) and limit of quantification (LOQ) for tramadol in urine samples were 1.2 and 3.5 μg L⁻¹, respectively. These limits for tramadol in plasma samples were 3.0 and 8.5 μg L⁻¹, respectively. The recoveries for plasma and urine samples were higher than 91%.     

Reading Biochips by Raman and Surface-Enhanced Raman Spectroscopies

Biochips are a rapidly increasing research field, driven by the versatility of sensing devices and the importance of their applications. The regular approaches for creating biochips and for reading them suffer from some limitations, motivating development of miniature biochips and label-free formats. To push forward these challenges, we have chosen to combine the methods of printing of droplets of synthetic receptors by pipettes or nanofountain pens with detection by Raman spectroscopy or its surface-assisted plasmon variant, namely, surface-enhanced Raman spectroscopy (SERS). The selected receptors included molecularly imprinted polymers (MIPs), produced by polymerization of functional and cross-linking monomers around a molecular template, the β-blocking drug propranolol. The measured Raman and SERS spectra of the MIP constituents enabled identification of the template presence and consequently chemical imaging of individual and multiple dots in an array. This concept, combining nanolithography techniques with SERS paves the road toward miniaturized arrayed MIP sensors with label-free, specific and quantitative molecular recognition.