Plasticization of poly(L-lactide) with poly(propylene glycol)

A new plasticizer for poly(L-lactide) (PLA)-poly(propylene glycol) (PPG) is proposed. The advantage of using PPG is that it does not crystallize, has low glass transition temperature, and is miscible with PLA. PLA was plasticized with PPGs with nominal Mw of 425 and 1000 g/mol. Poly(ethylene glycol) (PEG), long known as a plasticizer for PLA, with nominal Mw of 600 g/mol, was also used to plasticize PLA for comparison. The thermal and tensile properties of PLA and PLA with 5-12.5 wt % of the plasticizers were studied. In blends of PLA with PPGs the glass transition temperature was lower than that of neat PLA. Both PPGs enhanced the crystallizability of PLA albeit less than PEG. All of the plasticizers increased also the ability of PLA to plastic deformation which was reflected in a decrease of yield stress and in an increase of elongation at break. The effect was enhanced by the higher PPG content and also by lower molecular weight of PPG. A phase separation occurred only in the blend containing 12.5 wt % of PPG with higher molecular weight. The evidences of crazing were found in deformed samples of PLA with low plasticizer content, whereas the samples with higher content of plasticizers crystallized due to deformation.     

Compatibilization effect of poly(epsilon-caprolactone)-b-poly(ethylene glycol) block copolymers and phase morphology analysis in immiscible poly(lactide)/poly(epsilon-caprolactone) blends

The miscibility and phase behavior of two stereoisomer forms of poly(lactide) (PLA: poly (L-lactide) (PLLA) and poly(DL-lactide) (PDLLA)) blends with poly(epsilon-caprolactone)-b-poly(ethylene glycol) (PCL-b-PEG) and PCL-b-monomethoxy-PEG (PCL-b-MPEG) block copolymers have been investigated by differential scanning calorimetry (DSC). The DSC thermal behavior of both the blend systems revealed that PLA is miscible with the PEG segment phase of PCL-b-(M)PEG but is still immiscible with its PCL segment phase although PCL was block-copolymerized with PEG. On the basis of these results, PCL-b-PEG was added as a compatibilizer to PLA/PCL binary blends. The improvement in mechanical properties of PLA/PCL blends was achieved as anticipated upon the addition of PCL-b-PEG. In addition, atomic force microscopy (AFM) measurements have been performed in order to study the compositional synergism to be observed in mechanical tests. AFM observations of the morphological dependency on blend composition indicate that PLA/PCL blends are immiscible but compatible to some extent and that synergism of compatibilizing may be maximized in the compositional blend ratio before apparent phase separation and coarsening.     

Novel chitosan-based films cross-linked by genipin with improved physical properties

Novel cross-linked chitosan-based films were prepared using the solution casting technique. A naturally occurring and nontoxic cross-linking agent, genipin, was used to form the chitosan and chitosan/poly(ethylene oxide) (PEO) blend networks, where two types of PEO were used, one with a molecular weight of 20 000 g/mol (HPEO) and the other of 600 g/mol (LPEO). Genipin is used in traditional Chinese medicine and extracted from gardenia fruit. Importantly, it overcomes the problem of physiological toxicity inherent in the use of some common synthetic chemicals as cross-linking agents. The mechanical properties and the stability in water of cross-linked and un-crosslinked chitosan and chitosan/PEO blend films were investigated. It was shown that, compared to the transparent yellow, un-cross-linked chitosan/PEO blend films, the genipin-cross-linked chitosan-based film, blue in color, was more elastic, was more stable, and had better mechanical properties. Genipin-cross-linking produced chitosan networks that were insoluble in acidic and alkaline solutions but were able to swell in these aqueous media. The swelling characteristics of the films exhibit sensitivity to the environmental pH and temperature. The surface properties of the films were also examined by contact angle measurements using water and mixtures of water/ethanol. The results showed that, with the one exception of cross-linked pure chitosan in 100% water, the cross-linked chitosan and chitosan/PEO blends were more hydrophobic than un-crosslinked ones.     

Molecular dynamics and dissipative particle dynamics simulations for prediction of miscibility in polyethylene terephthalate/polylactide blends

The miscibility of polyethylene terephthalate (PET)/polylactide (PLA) blends is studied through atomistic molecular dynamics (MD) and mesoscale dissipative particle dynamics (DPD) simulation. Five PET/PLA blends (with the weight ratio at 90/10, 70/30, 50/50, 30/70 and 10/90) as well as pure PET and PLA are examined. The solubility parameter values obtained by using the MD simulation are in good agreement with the reference data. The Flory–Huggins parameters, χ, which are computed for different blends and determined from the cohesive energy densities, with the radial distribution functions g(r) of the inter-molecular atoms, suggest that PET is completely miscible with PLA over the entire composition range. This is further proved by the mesoscopic morphologies of PET/PLA blends. All the simulation results are qualitatively consistent with the experimental results, and demonstrate that the modelling strategies in this study may serve as a powerful tool for predicting miscibility and mesoscopic morphology of polymer blends.     

Morphology and properties of soy protein and polylactide blends

Blends of soy protein (SP) and a semicrystalline polylactide (PLA) were prepared using a twin-screw extruder. The melt rheology, phase morphology, mechanical properties, water resistance, and thermal and dynamic mechanical properties were investigated on specimens prepared by injection molding of these blends. The melt flowability of soy-based plastics was improved through blending with PLA. Scanning electron microscopy revealed that a co-continuous phase structure existed in the blends with soy protein concentrate (SPC) to PLA ratios ranging from 30:70 to 70:30. SPC/PLA blends showed fine co-continuous phase structures, while soy protein isolate (SPI)/PLA blends presented severe phase coarsening. At the same SP to PLA ratios, SPC/PLA blends demonstrated a higher tensile strength than SPI/PLA blends. The water absorption of soy plastics was greatly reduced by blending with PLA. The compatibility was improved by adding 1-5 phr poly(2-ethyl-2-oxazoline) (PEOX) in the blends, and the resulting blends showed an obvious increase in tensile strength and a reduction in water absorption for SPI/PLA blends. The compatibility between SP and PLA was evaluated by mechanical testing, dynamic mechanical analysis (DMA), water absorption, and scanning electron microscopy (SEM) experiments. Differential scanning calorimetry (DSC) revealed that PLA in the blends was mostly amorphous in the injection molded articles, and SP accelerated the cold crystallization and could increase the final crystallinity of PLA in the blends.     

Compatible ternary blends of chitosan/poly(vinyl alcohol)/poly(lactic acid) produced by oil-in-water emulsion processing

Ternary compatible blends of chitosan, poly(vinyl alcohol), and poly(lactic acid) were prepared by an oil-in-water (O/W) emulsion process. Solutions of chitosan in aqueous acetic acid, poly(vinyl alcohol) (PVA) in water, and poly(lactic acid) (PLA) in chloroform were blended with a high-shear mixer. PVA was used as an emulsifier to stabilize the emulsion and to reduce the interfacial tension between the solid polymers in the blends produced. It proved to work very well because the emulsions were stable for periods of days or weeks and compatible blends were obtained when PVA was added. This effect was attributed to a synergistic effect of PVA and chitosan because the binary blends PVA/PLA and chitosan/PLA were completely incompatible. The blends were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermal mechanical analysis (TMA), stress-strain tests, and Fourier transform infrared spectroscopy (FTIR). The results indicated that despite the fact that the system contained distinct phases some degree of molecular miscibility occurred when the three components were present in the blend.     

A study of conformational stability of poly(L-alanine), poly(L-valine), and poly(L-alanine)/poly(L-valine) blends in the solid state by (13)C cross-polarization/magic angle spinning NMR

13C cross-polarization/magic angle spinning (CP/MAS) NMR and (1)H T(1rho) experiments of poly(L-alanine) (PLA), poly(L-valine) (PLV), and PLA/PLV blends have been carried out in order to elucidate the conformational stability of the polypeptides in the solid state. These were prepared by adding a trifluoroacetic acid (TFA) solution of the polymer with a 2.0 wt/wt % of sulfuric acid (H(2)SO(4)) to alkaline water. From these experimental results, it is clarified that the conformations of PLA and PLV in their blends are strongly influenced by intermolecular hydrogen-bonding interactions that cause their miscibility at the molecular level.     

Preparation and properties of plasticized poly(lactic acid) films

Poly(lactic acid), PLA, was blended with monomeric and oligomeric plasticizers in order to enhance its flexibility and thereby overcome its inherent problem of brittleness. Differential scanning calorimetry, dynamic mechanical analysis, transmission electron microscopy, and tensile testing were used to investigate the properties of the blends. Monomeric plasticizers, such as tributyl citrate, TbC, and diethyl bishydroxymethyl malonate, DBM, drastically decreased the T(g) of PLA, but the blends showed no morphological stability over time since rapid cold crystallization caused a size reduction of the amorphous domains in PLA. Consequently, the ability of PLA to accommodate the plasticizer diminished with the increase in crystallinity and migration of the plasticizer occurred. Increasing the molecular weight of the plasticizers by synthesizing oligoesters and oligoesteramides resulted in blends that displayed T(g) depressions slightly smaller than with the monomeric plasticizers. The compatibility with PLA was dependent on the molecular weight of the oligomers and on the presence or not of polar amide groups that were able to positively interact with the PLA chains. Aging the materials at ambient temperature revealed that the enhanced flexibility as well as the morphological stability of the films plasticized with the oligomers could be maintained as a result of the higher molecular weight and the polar interactions with PLA.     

Effect of filler content and size on transport properties of water vapor in PLA/calcium sulfate composites

Starting from calcium sulfate (gypsum) as fermentation byproduct of lactic acid production process, high-performance composites have been produced by melt-blending polylactide (PLA) and beta-anhydrite II (AII) filler, i.e., calcium sulfate hemihydrate previously dried at 500 degrees C. Characterized by attractive properties due to good filler dispersion throughout the polyester matrix and favorable interactions between components, these composites are interesting for potential use as biodegradable rigid packaging. The effect of filler content and mean particle diameter on the barrier properties such as sorption and diffusion to water vapor has been examined and compared to unfilled PLA. Even without additional treatments, the presence of the filler introduced constraints on molecular mobility in the permeable phase of amorphous PLA and the amount of solvent absorbed appears lower in the highly filled composites. Surprisingly, for PLA-30% AII compositions, by addition of filler characterized by high mean particle diameter (e.g., 43 microm) the thermodynamic diffusion parameter, D(0), decreased up to 2 orders of magnitude. The dimension of filler particles and their percentage in the continuous polymeric phase seem to be the most important parameters that determine the barrier properties of the PLA-AII composites to water vapor.     

Study of biodegradable polylactide/poly(butylene adipate-co-terephthalate) blends

Both polylactide (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable polymers. They are thermoplastics which can be processed using most conventional polymer processing methods. PLA is high in strength and modulus (63 MPa and 3.4 GPa, respectively) but brittle (strain at break 3.8%) while PBAT is flexible and tough (strain at break approximately 710%). In view of their complementary properties, blending PLA with PBAT becomes a natural choice to improve PLA properties without compromising its biodegradability. In this study, PLA and PBAT were melt blended using a twin screw extruder. Melt elasticity and viscosity of the blends increased with the concentration of PBAT. Crystallization of the PLA component, phase morphology of the blend, mechanical properties, and toughening mechanism were investigated. The blend comprised an immiscible, two-phase system with the PBAT evenly dispersed in the form of approximately 300 nm domains within the PLA matrix. The PBAT component accelerated the crystallization rate of PLA but had little effect on its final degree of crystallinity. With the increase in PBAT content (5-20 wt %), the blend showed decreased tensile strength and modulus; however, elongation and toughness were dramatically increased. With the addition of PBAT, the failure mode changed from brittle fracture of the neat PLA to ductile fracture of the blend as demonstrated by tensile test and scanning electron microcopy (SEM) micrographs. Debonding between the PLA and PBAT domains induced large plastic deformation in PLA matrix ligaments.     

Liquid,phenylazide-end-capped copolymers of epsilon-caprolactone and trimethylene carbonate: preparation,photocuring characteristics,and surface layering

Photoreactive phenylazide-end-capped liquid copolymers were prepared by ring-opening copolymerization of epsilon-caprolactone (CL) and trimethylene carbonate (TMC) at an equimolar monomer feed ratio in the presence of a polyol, namely, a low-molecular-weight alcohol (di-, tri-, and tetraol) or poly(ethylene glycol) (PEG) as an initiator and tin(II) 2-ethylhexanoate as a catalyst, followed subsequently by phenylazide derivatization at their hydroxyl terminus. These tri- and tetrabranched liquid copolymers (precursors) with a molecular weight from approximately 2500 to 7000 g/mol were cross-linked to yield insoluble solids by ultraviolet (UV) light irradiation. The photocuring rate increased with increasing functionality of phenylazide and UV intensity and decreasing thickness of the liquid film of precursors. The photo-cross-linkability of phenylazide-derivatized liquid copolymers was found to be higher than that of the corresponding coumarin-derivatized liquid copolymers. Poly(lactide) (PLA) films surface-layered with photocured copolymers were prepared by coating surfaces with phenylazide-derivatized copolymers and their subsequent photoirradiation. Endothelial cells adhered well on the nontreated PLA and low-molecular-weight alcohol-based copolymer-layered and photocured films. Little cell adhesion was observed on the hydrolytically surface-eroded PLA film and the PEG-based copolymer-layered film. When a phenylazide-derivatized hexapeptide with the cell-adhesion tripeptidyl sequence, Arg-Gly-Asp (RGD), common to cell adhesive proteins, was photoimmobilized on these surfaces, the surfaces became cell adhesive. Microarchitectured surfaces, which were prepared by sequential procedures of surface coating and photocuring using a photomask with lattice windows, produced regionally differentiated cell adhesiveness.     

Investigation of the role of hydrophilic chain length in amphiphilic perfluoropolyether/poly(ethylene glycol) networks: towards high-performance antifouling coatings

The facile preparation of amphiphilic network coatings having a hydrophobic dimethacryloxy-functionalized perfluoropolyether (PFPE-DMA; M(w) = 1500 g mol(-1)) crosslinked with hydrophilic monomethacryloxy functionalized poly(ethylene glycol) macromonomers (PEG-MA; M(w) = 300, 475, 1100 g mol(-1)), intended as non-toxic high-performance marine coatings exhibiting antifouling characteristics is demonstrated. The PFPE-DMA was found to be miscible with the PEG-MA. Photo-cured blends of these materials containing 10 wt% of PEG-MA oligomers did not swell significantly in water. PFPE-DMA crosslinked with the highest molecular weight PEG oligomer (ie PEG1100) deterred settlement (attachment) of algal cells and cypris larvae of barnacles compared to a PFPE control coating. Dynamic mechanical analysis of these networks revealed a flexible material. Preferential segregation of the PEG segments at the polymer/air interface resulted in enhanced antifouling performance. The cured amphiphilic PFPE/PEG films showed decreased advancing and receding contact angles with increasing PEG chain length. In particular, the PFPE/PEG1100 network had a much lower advancing contact angle than static contact angle, suggesting that the PEG1100 segments diffuse to the polymer/water interface quickly. The preferential interfacial aggregation of the larger PEG segments enables the coating surface to have a substantially enhanced resistance to settlement of spores of the green seaweed Ulva, cells of the diatom Navicula and cypris larvae of the barnacle Balanus amphitrite as well as low adhesion of sporelings (young plants) of Ulva, adhesion being lower than to a polydimethyl elastomer, Silastic T2.     

Sizing the Bacillus anthracis PA63 channel with nonelectrolyte poly(ethylene glycols)

Nonelectrolyte polymers of poly(ethylene glycol) (PEG) were used to estimate the diameter of the ion channel formed by the Bacillus anthracis protective antigen 63 (PA₆₃). Based on the ability of different molecular weight PEGs to partition into the pore and reduce channel conductance, the pore appears to be narrower than the one formed by Staphylococcus aureus α-hemolysin. Numerical integration of the PEG sample mass spectra and the channel conductance data were used to refine the estimate of the pore's PEG molecular mass cutoff (∼1400 g/mol). The results suggest that the limiting diameter of the PA₆₃ pore is <2 nm, which is consistent with an all-atom model of the PA₆₃ channel and previous experiments using large ions.     

A study of conformational stability of polyglycine and poly(L-alanine), and polyglycine/poly(L-alanine) blends in the solid state by (13)C cross-polarization/magic angle spinning NMR

13C Cross-Polarization/Magic Angle Spinning nmr and T(1rhoH) experiments of polyglycine (PG), poly(L-alanine) (PLA), and PG/PLA blends prepared from dichloroacetic acid solution have been carried out, in order to elucidate the conformational stability of these polypeptides in the solid state. From these experimental results, it was clarified that the conformations of PG and PLA in their blends are strongly influenced by intermolecular hydrogen-bonding interactions that cause their miscibility at the molecular level.     

FT-IR imaging spectroscopy of phase separation in blends of poly(3-hydroxybutyrate) with poly(L-lactic acid) and poly(epsilon-caprolactone)

The detection of phase separation and identification of miscibility in biopolymer blends is an important aspect for the improvement of their physical properties. In this article, the phase separation in blends of poly(3-hydroxybutyrate) (PHB) with poly(L-lactic acid) (PLA) and poly(epsilon-caprolactone) (PCL), respectively, has been studied as a function of the blend composition by FT-IR imaging spectroscopy. For both polymer blend systems, a miscibility gap has been found around the 50:50% (w/w) composition of the two components. Furthermore, the separating phases have been identified as blends of the two polymer components and their compositions could be determined from calibrations based on the spectra of the blends in the compositional range of miscibility. The data derived from FT-IR spectroscopic imaging were corroborated by additional DSC analyses and mechanical stress-strain measurements of polymer blend films, which exhibited a characteristic fracture behavior as a function of PHB composition.     

Chemical synthesis of cross-linked poly(KGGVG), an elastin-like biopolymer

Previous studies afforded on peptides and polypeptides containing repetitive sequences of elastin have largely demonstrated that their molecular and supramolecular properties are fully representative of those of tropoelastin, the soluble, linear precursor of elastin itself. In the attempt to synthesize cross-linked elastin-mimetic polypeptides, the repeating sequence VGGVG (V: valine; G: glycine), typical of elastin, was modified to incorporate lysine residues, yielding the polymer poly(KGGVG) (K: lysine). This imparts primary amine functionality susceptible to cross-linking reaction with appropriate bifunctional cross-linking reagents. We report herein the chemical synthesis and cross-linking of poly(KGGVG) with glutaraldehyde (GTA) and with disuccinimidyl glutarate (DSG). In both cases, the characterization of the polymers, both linear and cross-linked, has been carried out by CD spectroscopy and transmission electron microscopy measurements. The obtained results, although not conclusive, demonstrate that poly(KGGVG), both linear and cross-linked, may be considered very similar to tropoelastin and mature elastin, as concerns its molecular and supramolecular properties.     

Polycaprolactone-poly(ethylene glycol) multiblock copolymers as potential substitutes for di(ethylhexyl) phthalate in flexible poly(vinyl chloride) formulations

New high-molecular-weight hydrophobic/hydrophilic segmented copolymers of poly(ester ether carbonate) structure, containing poly(epsilon-caprolactone) (PCL) and poly(ethylene glycol) (PEG) segments in their main chain, were synthesized and characterized. These copolymers were obtained by a two-step chain-extension reaction carried out in the presence of alpha,omega-dihydroxy-oligoPCL of molecular weight 1250 and PEG samples of molecular weight 150, 400, 600, 1000, and 2000. The molecular structures of all synthesized materials were characterized by means of (1)H NMR and (13)C NMR spectroscopy, their molecular weights were determined by means of size exclusion chromatography, and their thermal properties were obtained by means of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The poly(ester ether carbonate)s of this study are partly or totally miscible at least up to 50 wt % with poly(vinyl chloride) (PVC) and could be used to produce flexible PVC formulations. The miscibility between PVC and the poly(ester ether carbonate)s reported in this paper was investigated by means of DSC and DMA analysis. PVC blends were also analyzed by determining their swellability and the amount of extractables in aqueous media. By comparison purposes, the chain-extension product of PCL1250, that is, PCL polycarbonate, was also synthesized and characterized. The results obtained demonstrated that the copolymers with shortest PEG segment length, i.e. PEG150, 400, and 600, give the best results in terms of miscibility with PVC and lead to blends with maximum resistance to extraction by water. Therefore, they represent, in principle, good substitutes for low-molecular-weight, leachable PVC plasticizers, such as di(ethylhexyl) phthalate.     

Photo-cross-linked hybrid polymer networks consisting of poly(propylene fumarate) and poly(caprolactone fumarate): controlled physical properties and regulated bone and nerve cell responses

Aiming to achieve suitable polymeric biomaterials with controlled physical properties for hard and soft tissue replacements, we have developed a series of blends consisting of two photo-cross-linkable polymers: polypropylene fumarate (PPF) and polycaprolactone fumarate (PCLF). Physical properties of both un-cross-linked and UV cross-linked PPF/PCLF blends with PPF composition ranging from 0% to 100% have been investigated extensively. It has been found that the physical properties such as thermal, rheological, and mechanical properties could be modulated efficiently by varying the PPF composition in the blends. Thermal properties including glass transition temperature (T g) and melting temperature (T m) have been correlated with their rheological and mechanical properties. Surface characteristics such as surface morphology, hydrophilicity, and the capability of adsorbing serum protein from culture medium have also been examined for the cross-linked polymer and blend disks. For potential applications in bone and nerve tissue engineering, in vitro cell studies including cytotoxicity, cell adhesion, and proliferation on cross-linked disks with controlled physical properties have been performed using rat bone marrow stromal cells and SPL201 cells, respectively. In addition, the role of mechanical properties such as surface stiffness in modulating cell responses has been emphasized using this model blend system.     

Effect of homo poly(L-amino acids) on fibrin assembly: role of charge and molecular weight

Positively charged molecules such as protamine, leukocyte cationic protein, and the carboxyl terminus of platelet factor 4 have been shown to increase fibrin fiber thickness. Synthetic homo poly(L-amino acids) were used to explore the role of charge and molecular weight of cationic molecules on fibrin assembly. The effects of poly(L-lysine) (PLL), poly(L-glutamic acid) (PLG), poly(L-aspartic acid) (PLA), poly(L-histidine) (PLH), and poly(L-arginine) (PLArg) on the assembly and structure of fibrin gels were studied by using light-scattering techniques. At a PLG (Mr 60,000) concentration of 80 micrograms/mL and a PLA (Mr 20,000) concentration of 64 microgram/mL, neither of these negatively charged polymers produced a detectable change in either fibrin assembly kinetics or final structure. Positively charged PLArg (16 micrograms/mL) caused a 30% increase in fibrin fiber mass/length ratio without calcium. In contrast, PLH (16 micrograms/mL), also positively charged, had no effect in the absence of CaCl2 but produced a 40% increase in fiber mass/length ratio with 5 mM CaCl2. At concentrations as low as 1 microgram/mL, positively charged PLL increased the initial fibrin assembly kinetics and led to larger fiber mass/length ratio. The impact on fibrin mass/length ratio was equivalent for three different molecular weight preparations of PLL (Mr 25,000, 90,000, and 240,000). The lack of a molecular weight effect on fiber thickness and the low polymer concentrations required to produce the perturbation argue against an excluded volume effect as the mechanism by which lateral fiber growth is augmented. Mechanisms by which poly(L-amino acids) may perturb fibrin assembly are discussed.     

Structural and functional properties of BaTX, a new Lys49 phospholipase A2 homologue isolated from the venom of the snake Bothrops alternatus

BaTX PLA(2), a K49 phospholipase A(2) homologue was purified from Bothrops alternatus venom after two chromatographic steps, molecular exclusion on Superdex 75 and reverse phase HPLC on mu-Bondapack C-18. A molecular mass of 13898.71 Da was determined by MALDI-TOF mass spectrometry. The amino acid composition showed that BaTX has a high content of Lys, Tyr, Gly, Pro, and 14 half-Cys residues, typical of a basic PLA(2). The complete amino acid sequence of BaTX PLA(2) contains 121 residues, resulting in a calculated pI value of 8.63. This sequence shows high identity values when compared to other K49 PLA(2)s isolated from the venoms of viperid snakes. Lower identity is observed in comparison to D49 PLA(2)s. The sequence was SLFELGKMIL QETGKNPAKS YGAYYCYCGW GGQGQPKDAT DRCCYVHKCC YKKLTGCNPK KDRYSYSWKD KTIVCGENNS CLKELCECDK AVAICLRENL NTYNKKYRYY LKPLCKKADA C. In mice, BaTX induced myonecrosis and edema, upon intramuscular or subcutaneous injections, respectively. The LD(50) of BaTX was 7 mug/g body weight, by intravenous route. In vitro, the toxin caused a potent blockade of neuromuscular transmission in young chicken biventer cervicis preparations. The blockage 50% was achieved at a concentration of 0.03 microM: 40+/-0.4 min and 0.07 microM: 35+/-0.3 min. Moreover, this protein induced a rapid cytolytic effect upon mouse skeletal muscle myoblasts in culture. Thus, the combined structural and functional information obtained identify BaTX as a new member of the K49 PLA(2) family, which presents the typical bioactivities described for such proteins.