Embedding Media for 1-2 Micron Sectioning. 2. Hydroxyethyl Methacrylate Combined with 2-Butoxyethanol

A hydroxyethyl methacrylate monomer medium incorporating 2-butoxyethanol requires 2 stock solutions for embedding. Solution A: 80 ml of hydroxyethyl methacrylate (Rohm and Haas Co., Philadelphia, Pa.) is mixed well with 16 ml of 2-butoxyethanol; 0.27 gm of benzoyl peroxide, the catalyst, is added and permitted to dissolve. Heating to 40-50 C may be used to accelerate its solution. Solution B: polyethylene glycol 200 or 400, 15 parts, and N,N-dimethylaniline, 1 part, are mixed thoroughly. Tissues are dehydrated in the customary manner to absolute ethanol or other comparable dehydrant, infiltrated completely with A, then cast in a mixture consisting of 42 parts of A well mixed with 1 part of B. Polymerizaion occurs in 4-7 hr. In a water bath at 20 C the time required was about 7 hr; at 28 C, 4 hr. This medium is based on the author's water-polyethylene glycol-hydroxyethyl methacrylate monomer medium (Stain Techn., 42: 119-23, 1967).     

Bleaching of chlorophylls in alcohol extracts with benzoyl peroxide for liquid scintillation counting of C-labeled compounds

Benzoyl peroxide in toluene was used to bleach chlorophylls in alcohol extracts from plants fed with ¹⁴CO₂ for improved direct measurement by liquid seintillation counting. The 0.5% benzoyl peroxide was better than the saturated solution due to less color quenching. Increased counts occurred with all five common scintillation systems when the leaf extracts were bleached with the 0.5% benzoyl peroxide. However, the relatively colorless root extracts of ¹⁴C-labeled photosynthates in alcohol did not require the addition of benzoyl peroxide for decolorization. The addition of 0.5 ml of benzoyl peroxide solution (0.5%) to 0.5 ml of a solution of 10 ¹⁴C-labeled compounds did not induce the degradation of these compounds. In contrast, sodium hypochlorite at an equal concentration caused considerable losses of radioactivity, with an overall average of 30% reduction of the 10 ¹⁴C-labeled compounds examined.     

Embedding Media for 1-2 Micron Sectioning. 3. Hydroxyethyl Methacrylate-Benzoyl Peroxide Activated with Pyridine

A hydroxyethyl methacrylate (HEMA) monomer medium containing 2-butoxyethanol as the plasticizer requites only one stock solution consisting of: 50 ml of 94 or 96% HEMA containing 200 ppm inhibitor (Rohm and Haas, Philadelphia) is mixed with 12 ml 2-butoxyethanol; 0.25 gm benzoyl peroxide is added and permitted to dissolve at 20-25 C. This mixture is activated by the addition of 0.8-1.0 ml of pyridine. Polymerization of the activated mixture is initated in 15-20 hr at 25 C and in 2-4 hr at 50 C; polymerization of the mixture is complete in 2-3 days and 3-6 hr, respectively. The activated monomer mixture is stable at temperatures below 18 C; hence infiltration of tissues may be extended to 7-10 days by keeping the mixture at 0 to -40 C.     

A Plastic Embedding Medium for Thin Sectioning in Light Microscopy

Tissue blocks with surface areas up to 2 cm² can be sectioned at 1 or 2 μ after embedding in a medium consisting of: methyl methacrylate, 27 ml; polyethylene glycol distearate MW 1540, 6 gm; dibutyl phthalate, 4 ml; and Plexiglas molding powder A-100, 9 gm (added last). The methacrylate mixture is polymerized at 50° C by benzoyl peroxide, 0.8 gm/ 100 ml of methacrylate. The polymerized matrix is transparent and the blocks can be cut on a rotary microtome with a steel knife. The plastic can be removed from sections with acetone prior to staining. Artifacts caused by embedding and sectioning are negligible     

Corrosion casting method for the gross anatomy of the blood vascular system of fish

A corrosion cast of the entire blood vascular system was made by a single injection of resin from the heart of carp and a Japanese catfish. Either semipolymerized methyl methacrylate or Mercox CL with 30–50% methyl methacrylate monomer was used as the resin preparation. The latter was better for photographing. Both were polymerized by addition of 1 % benzoyl peroxide. The segmental blood vessels of carp and a catfish showed an alternating arrangement of artery and vein in successive segments with some irregularity.     

Effect of alpha-tocopherol and N-acetylcysteine on benzoyl peroxide toxicity in human keratinocytes

Benzoyl peroxide is a free-radical generating compound widely used in the polymer industry and also in pharmaceuticals as antimicrobial agent to treat acne. However, benzoyl peroxide causes irritation and contact dermatitis in about 1% of patients. Concern over the use of this compound is motivated by the demonstration that it can also act as skin tumor promoter in mice. In addition, benzoyl peroxide induces DNA strand breaks in many cells, including keratinocytes. Benzoyl peroxide toxicity is presumably mediated by the formation of reactive free radicals and by the consumption of intracellular antioxidants.In this work we investigated the effect of both the lipophilic antioxidant alpha-tocopherol and the hydrophilic thiol donor N-acetylcysteine (NAC) in human keratinocyte line HaCaT exposed to benzoyl peroxide. A protective effect against benzoyl peroxide cytotoxicity was achieved when cells were grown on a alpha-tocopherol layer. On the contrary, the addition of alpha-tocopherol dissolved in ethanol had a pro-oxidant effect, leading to an enhancement of benzoyl peroxide toxicity. Cytotoxicity was also reduced adding NAC to the culture medium; the presence of both NAC and alpha-tocopherol exerts a synergistic cytoprotection.     

A Simplified Technique for Low Temperature Methyl Methacrylate Embedding

A simplified method for low temperature methyl methacrylate embedding with inhibited methyl methacrylate monomer is demonstrated using proper concentrations of benzoyl peroxide and N,N-dimethylaniline. The polymerized tissue blocks cut well and the tissue sections obtained show excellent acid phosphatase activity when demonstrated with the newly improved technique and Goldner's staining. Likewise, double tetracycline labels are well revealed by fluorescence microscopy.     

A simplified technique for low temperature methyl methacrylate embedding

A simplified method for low temperature methyl methacrylate embedding with inhibited methyl methacrylate monomer is demonstrated using proper concentrations of benzoyl peroxide and N,N-dimethylaniline. The polymerized tissue blocks cut well and the tissue sections obtained show excellent acid phosphatase activity when demonstrated with the newly improved technique and Goldner's staining. Likewise, double tetracycline labels are well revealed by fluorescence microscopy.     

Effects of rifampicin and doxycycline on the production of hydrogen peroxide by macrophages]

The influence of rifampicin and doxycycline on oxidative metabolism of macrophages was estimated in vitro by production of hydrogen peroxide. It was shown that low concentrations of rifampicin and doxycycline stimulated production of hydrogen peroxide by macrophages of guinea pigs. In concentrations of 1 to 10 micrograms/ml corresponding to the mean therapeutic ones doxycycline increased both the spontaneous and zymosan-induced production of hydrogen peroxide by the macrophages. The potentiating activity of doxycycline on the cells activated by opsonized zymosan was higher. The maximum increase in the induced production of hydrogen peroxide (by 40 per cent) was observed when the antibiotic concentration was 1 microgram/ml. Rifampicin in concentrations of 0.1 to 1 microgram/ml corresponding to the mean therapeutic ones stimulated the zymosan-induced production of hydrogen peroxide by the macrophages. The maximum increase in the production of hydrogen peroxide (by 22 per cent) was noted at the rifampicin concentration of 1 microgram/ml.     

Hydroxyethyl Methacrylate Combined with Polyethylene Glycol 400 and Water; an Embedding Medium for Routine 1-2 Micron Sectioning

Pieces of tissue, with the largest dimension not exceeding 7 mm, are fixed and dehydrated by the procedures of choice. Two stock solutions: A, for infiltration; and B, the accelerator, are used in embedding. Formulas: A, 80 ml of glycol methacrylate (2-hydroxyethyl methacrylate—Rohm and Haas Co., Philadelphia, Pa.) is mixed well with 12 ml of polyethylene glycol (Carbowax) 400 and 8 ml of water; then 0.27 gm of benzoyl peroxide added, heated to dissolve the peroxide, and allowed to cool to room temperature. B, polyethylene 200 or 400, 15 parts, and N,N-dimethylaniline, 1 part, mixed thoroughly. Tissues are first infiltrated completely with solution A, then cast in a mixture consisting of 42 parts of A mixed with 1 part of B. Polymerization occurs in 45 min to 3 hr, depending on the temperature. In a water bath at 20 C, the time required was found to be about 3 hr; at 25 C, 1.5 hr; and at 30 C, 45 min. The plastic block can be trimmed easily, and sections 1-2 μ thick readily cut. Sections can be attached to slides by water flotation, without adhesive, and should be dried at room temperature. Staining with aqueous solutions of basic and acid dyes, without removing the embedding matrix, is sharp and brilliant. When staining of the matrix by basic dyes occurs, this background stain can be completely removed by differentiating in either 2-butoxyethanol, pure ethanol, or a mixture of the two. A number of histochemical reagents have been found compatible with this embedding procedure.     

Septage treatments to reduce the numbers of bacteria and polioviruses.

Disposal of the pumped contents of septic tanks (septage) represents a possible means of dissemination of enteric pathogens including viruses, since persistence of enteroviruses in septic tank sludge for greater than 100 days has been demonstrated. The risk of exposure to potentially infectious agents can be reduced by disinfecting septages before their disposal. Of the septage disinfectants examined (technical and analytical grade glutaraldehyde, hydrogen peroxide, heat treatments, and a combination of heat and hydrogen peroxide), the treatment including hydrogen peroxide (5 mg, plus 0.33 mg of trichloroacetic acid, per ml of septage) and 55 degrees C killed virtually all the bacteria in septage within 1 h, whereas 55 degrees C alone inactivated inoculated polioviruses within 30 min. Virus was the most sensitive to heat, whereas fecal coliforms appeared to be the most sensitive to all chemical treatments. The responses of fecal streptococci and virus to both grades of glutaraldehyde (each at 1 mg/ml) were similar. Virus was more resistant than either fecal streptococci or total bacteria to low concentrations of hydrogen peroxide (1 to 5 mg/ml); however, virus and fecal streptococci were more labile than total bacteria to the highest peroxide concentration (10 mg/ml) examined. It is possible that the treatment combining heat and hydrogen peroxide was the most effective in reducing the concentrations of all bacteria, because catalase and peroxidases as well as other enzymes were heat inactivated, although catalase seems the most likely cause of damage. However, this most effective treatment does not appear to be practical for on-site use as performed, so further work on septage disinfection is recommended.     

Septage treatments to reduce the numbers of bacteria and polioviruses

Disposal of the pumped contents of septic tanks (septage) represents a possible means of dissemination of enteric pathogens including viruses, since persistence of enteroviruses in septic tank sludge for greater than 100 days has been demonstrated. The risk of exposure to potentially infectious agents can be reduced by disinfecting septages before their disposal. Of the septage disinfectants examined (technical and analytical grade glutaraldehyde, hydrogen peroxide, heat treatments, and a combination of heat and hydrogen peroxide), the treatment including hydrogen peroxide (5 mg, plus 0.33 mg of trichloroacetic acid, per ml of septage) and 55 degrees C killed virtually all the bacteria in septage within 1 h, whereas 55 degrees C alone inactivated inoculated polioviruses within 30 min. Virus was the most sensitive to heat, whereas fecal coliforms appeared to be the most sensitive to all chemical treatments. The responses of fecal streptococci and virus to both grades of glutaraldehyde (each at 1 mg/ml) were similar. Virus was more resistant than either fecal streptococci or total bacteria to low concentrations of hydrogen peroxide (1 to 5 mg/ml); however, virus and fecal streptococci were more labile than total bacteria to the highest peroxide concentration (10 mg/ml) examined. It is possible that the treatment combining heat and hydrogen peroxide was the most effective in reducing the concentrations of all bacteria, because catalase and peroxidases as well as other enzymes were heat inactivated, although catalase seems the most likely cause of damage. However, this most effective treatment does not appear to be practical for on-site use as performed, so further work on septage disinfection is recommended.     

Inhibition of benzoyl peroxide and ultraviolet-B radiation induced oxidative stress and tumor promotion markers by cycloartenol in murine skin

The chemopreventive potential of cycloartenol on benzoyl peroxide and UVB radiation-induced cutaneous tumor promotion markers and oxidative stress in murine skin is assessed. Benzoyl peroxide treatment (20 mg/animal/0.2 ml acetone) and UVB radiation (0.420 J/m(2)/s) caused a decrease in the activities of cutaneous antioxidant enzymes namely, catalase, glutathione peroxidase, glutathione reductase, glucose-6-phosphate dehydrogenase, phase II metabolizing enzyme such as glutathione-S-transferase and quinone reductase and depletion in the level of cutaneous glutathione. There was also enhancement in cutaneous microsomal lipid peroxidation, xanthine oxidase activity, [(14)C]-ornithine decarboxylase activity and [(3)H]-thymidine incorporation into cutaneous DNA. Cycloartenol was topically applied prior to the application of benzoyl peroxide at dose levels of 0.2 mg and 0.4 mg/kg body weight in acetone, which resulted in significant inhibition of epidermal ornithine decarboxylase activity and DNA synthesis (P < 0.001). There was also significant reduction of lipid peroxidation and xanthine oxidase activity (P < 0.001). In addition, the depleted levels of glutathione, inhibited activities of antioxidant and phase II metabolizing enzymes, were also recovered to a significant level (P < 0.001). The data indicate that cycloartenol is an effective chemopreventive agent in skin carcinogenesis.     

The treatment of skin carcinoma, induced by UV B radiation, using 1-oxo-5beta, 6beta-epoxy-witha-2-enolide, isolated from the roots of Withania somnifera, in a rat model.

Histopathological studies of the cutaneous tissues of Wistar rats exposed to UV B radiation (294 nm) for 20 days and rats exposed to UV B radiation for 20 days, followed by topical treatment with benzoyl peroxide, a tumor promoter (20 mg/animal/0.2 ml acetone) twice a week for 1 month, and kept under observation for 12 weeks, demonstrate the development of malignancy. Pretreatment of the animals with 1-oxo-5beta, 6beta-epoxy-witha-2-enolide (20 mg/kg bwt.), isolated from the roots of Withania somnifera, prior to exposing the animals to UV B radiation, prevents the incidence of skin carcinoma. The administration of 1-oxo-5beta, 6beta-epoxy-witha-2-enolide, to the animals after exposing them to UV B radiation/UV B radiation and benzoyl peroxide also prevents the occurrence of malignancy in the cutaneous tissue. Immunohistochemical staining of the cutaneous tissues of rats exposed to UV B radiation show the presence of p53 + foci (clusters of cells containing the mutated p53 protein), whereas an absence of p53 + foci is observed in animals pretreated with 1-oxo-5beta, 6beta-epoxy-witha-2-enolide. These results prove that 1-oxo-5beta, 6beta-epoxy-witha-2-enolide has the potential for acting as an effective agent to prevent the incidence of skin carcinoma induced by UV B radiation.     

An improved method for embedding hard tissue in polymethyl methacrylate

An improved routine method for embedding tissue, especially hard tissue, in polymethyl methacrylate (pMMA) is described. The improvements were: the final dehydration step before MMA infiltration was performed with methanol in a Soxhlet apparatus; the stabilizer hydroquinone was not extracted from the monomer (MMA), and more important, the commonly used polymerization initiator, benzoyl peroxide (bpo), was replaced by the initiator, bis (4-tert-butylcyclohexyl)peroxydicarbonate (bbpd). Bbpd is preferred to bpo because it is not explosive, far less is needed and it has a suitable half life. Moreover, bbpd, as obtained from the manufacturer, needs no further purification, in contrast to bpo. Temperatures during bbpd initiated polymerization did not exceed 48 C. In bbpd initiated pMMA, bubbles were almost never generated.     

An Improved Method for Embedding Hard Tissue in Poeymethyl Methacrylate

An improved routine method for embedding tissue, especially hard tissue, in poly-methyl methacrylate (pMMA) is described. The improvements were: the final dehydration step before MMA infiltration was performed with methanol in a Soxhlet apparatus; the stabilizer hydroquinone was not extracted from the monomer (MMA), and more important, the commonly used polymerization initiator, benzoyl peroxide (bpo), was replaced by the initiator, bis (4-tert-butylcyclohexyl)peroxydicarbonate (bbpd). Bbpd is preferred to bpo because it is not explosive, far less is needed and it has a suitable half life. Moreover, bbpd, as obtained from the manufacturer, needs no further purification, in contrast to bpo. Temperatures during bbpd initiated polymerization did not exceed 48 C. In bbpd initiated pMMA, bubbles were almost never generated.     

Inhibitory effect of eugenol on Cu2+-catalyzed lipid peroxidation in human erythrocyte membranes

1. The effects of eugenol on lipid peroxidation catalyzed by hydrogen peroxide (H2O2) or benzoyl peroxide (BPO) in the presence of copper ions were studied in human erythrocyte membranes. 2. The production of hydroxyl radicals was suggested in the peroxidation system catalyzed by H2O2/Cu2+. 3. H2O2/Cu2+-dependent peroxidation was inhibited by eugenol in a concentration-dependent manner; peroxidation was inhibited 62% by 200 microM eugenol. 4. In the presence of eugenol, the peroxidation catalyzed by BPO/Cu2+ was inhibited in a concentration-dependent manner, and more than 100 microM eugenol completely inhibited peroxidation. 5. The inhibitory effect of eugenol was non-competitive against Cu2+ in H2O2/Cu2+- and BPO/Cu2+-dependent peroxidation. 6. It is suggested that eugenol inhibits formation of hydroxyl radicals.     

A Tungstate Modification of the Golgi-Cox Method

Pieces of fresh nervous tissue 4-5 mm thick are put into the following solution: HgCl₂, 1 gm; K₂Cr₂O₇, 1 gm; K₂CrO₄, 0.8 gm; K₂WO₄ (or Na₂WO₄), 0.5 gm; distilled water 100 ml. They are kept undisturbed in the dark at room temperature for 20-30 days, then transferred to the following alkaline solution: LiOH (or NaOH), 1 gm; KNO₃, 15 gm; distilled water, 100 ml. After 12-24 hr in this solution they are washed for 12-24 hr in several changes of distilled water. (If sodium hydroxide was used, 0.5 ml of acetic acid should be added per 100 ml of wash water.) Embedding in celloidin follows dehydration. Sections are dehydrated in 3 parts of absolute alcohol and 1 part of chloroform, cleared in iodobenzene and mounted with a cover slip using a mounting medium with a refractive index around 1.61. The use of tungstate improves the general results and allows especially successful impregnations in very young animals, when the usual technic fails.     

Modification of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) film by chemical graft copolymerization

The graft copolymerization of 2-hydroxyethylmethacrylate (HEMA) onto poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBHV) films has been investigated. The graft copolymerization was conducted in aqueous media using benzoyl peroxide (BPO) as chemical initiator. PHBHV films were prepared by solvent casting. Different parameters affecting the graft yield were studied such as monomer concentration, initiator concentration, and reaction time. The extent of grafting has been modulated by the preparation conditions, in particular the concentration of HEMA. However, it is interesting to note that the initiator concentration had only a slight influence on the graft yield. Characterization of the grafted PHBHV films assumed that the graft copolymerization not only occurred on the film surface but also took place into the film bulk. Differential scanning calorimetry showed that crystallinity dramatically decreased with increasing graft yield, indicating that graft copolymerization hindered the crystallization process. Wettability has been obviously improved by grafting a hydrophilic monomer such as HEMA for high graft yield (>130%).     

A continuous-flow automated assay for iodometric estimation of hydroperoxides

An iodometric method for the analysis of hydroperoxides has been automated to allow analysis of aqueous biological samples (containing less than 20 mg/ml protein) and lipid hydroperoxide extracts. The evolution of triiodide ions is measured spectrophotometrically at 360 nm. Dependent on the type of sample, 30-60 samples can be analyzed per hour and the system allows detection of less than 100 pmol of peroxide. The assay is linear over a range of 100 pmol to 25 nmol. The sample volume used routinely was 80 microliters.