Preparation and characterization of cellulose nanocrystals from rice straw

Pure cellulose have been isolated from rice straw at 36% yield and hydrolyzed (64% H₂SO₄, 8.75 mL/g, 45 °C) for 30 and 45 min to cellulose nanocrystals (CNCs), i.e., CNC30 and CNC45, respectively. CNC45 was smaller (11.2 nm wide, 5.06 nm thick and 117 nm long) than CNC30 (30.7 nm wide, 5.95 nm thick and 270 nm long). Freeze-drying of diluted CNC suspensions showed both assembled into long fibrous structures: ultra-fine fibers (∼400 nm wide) from CNC45 and 1-2 μm wide broad ribbons interspersed with CNC clusters from CNC30. The self-assembled fibers from CNC30 and CNC45 were more highly crystalline (86.0% and 91.2%, respectively) and contained larger crystallites (7.36 nm and 8.33 nm, respectively) than rice straw cellulose (61.8%, 4.42 nm). These self-assembled fibers had essentially nonporous or macroporous structures with the CNCs well aligned along the fiber axis. Furthermore, the self-assembled ultra-fine fibers showed extraordinary structural stability, withstanding vigorous shaking and prolong stirring in water.     

Direct observation of unstained wet biological samples by scanning-electron generation X-ray microscopy

Analytical tools of nanometre-scale resolution are indispensable in the fields of biology, physics and chemistry. One suitable tool, the soft X-ray microscope, provides high spatial resolution of visible light for wet specimens. For biological specimens, X-rays of water-window wavelength between carbon (284 eV; 4.3 nm) and oxygen (540 eV; 2.3 nm) absorption edges provide high-contrast imaging of biological samples in water. Among types of X-ray microscope, the transmission X-ray microscope using a synchrotron radiation source with diffractive zone plates offers the highest spatial resolution, approaching 15-10 nm. However, even higher resolution is required to measure proteins and protein complexes in biological specimens; therefore, a new type of X-ray microscope with higher resolution that uses a simple light source is desirable. Here we report a novel scanning-electron generation X-ray microscope (SGXM) that demonstrates direct imaging of unstained wet biological specimens. We deposited wet yeasts in the space between two silicon nitride (Si₃N₄) films. A scanning electron beam of accelerating voltage 5 keV and current 1.6 nA irradiates the titanium (Ti)-coated Si₃N₄ film, and the soft X-ray signal from it is detected by an X-ray photodiode (PD) placed below the sample. The SGXM can theoretically achieve better than 5 nm resolution. Our method can be utilized easily for various wet biological samples of bacteria, viruses, and protein complexes.     

4Pi microscopy of the nuclear pore complex

To explore whether super-resolution fluorescence microscopy is able to resolve topographic features of single cellular protein complexes, a two-photon 4Pi microscope was used to study the nuclear pore complex (NPC). The microscope had an axial resolution of 110-130 nm and a two-color localization accuracy of 5-10 nm. In immune-labeled HeLa cells, NPCs could be resolved much better by 4Pi than by confocal microscopy. When two epitopes of the NPC, one localized at the tip of the cytoplasmic filaments and the other at the ring of the nuclear basket, were immune-labeled, they could be clearly resolved in single NPCs, with the distance between them determined to be 152 ± 30 nm. In cells expressing a green fluorescent protein construct localized at the NPC center, the distances between the ring of the nuclear filaments and the NPC center was 76 ± 12 (Potorous tridactylus cells) or 91 ± 21 nm (normal rat kidney cells), whereas the distance between the NPC center and the tips of the cytoplasmic filaments was 84 ± 18 nm, all values in good agreement with previous electron or single-molecule fluorescence estimates. We conclude that super-resolution fluorescence microscopy is a powerful method for analyzing single protein complexes and the cellular nanomachinery in general.     

The impact of DNA topology on polyplex uptake and transfection efficiency in mammalian cells

The effect of DNA vector topology when complexed to poly-l-lysine (PLL) and its quantification in transfection efficiency has not been fully addressed even though it is thought to be of importance from both production and regulatory viewpoints. This study investigates and quantifies cell uptake followed by transfection efficiency of PLL:DNA complexes (polyplexes) in Chinese hamster ovary (CHO) cells and their dependence on DNA topology. PLL is known for its ability to condense DNA and serve as an effective gene delivery vehicle. Characterization of PLL conjugated to a 6.9 kb plasmid was carried out. Dual labeling of both the plasmid DNA (pDNA) and PLL enabled quantitative tracking of the complexed as well as dissociated elements, within the cell, and their dependence on DNA topology. Polyplex uptake was quantified by confocal microscopy and image analysis. Supercoiled (SC) pDNA when complexed with PLL, forms a polyplex with a mean diameter of 139.06 nm (±0.84% relative standard error [RSE]), whereas open circular (OC) and linear-pDNA counterparts displayed mean diameters of 305.54 (±3.2% RSE) and 841.5 nm (±7.2% RSE) respectively. Complexes containing SC-pDNA were also more resistant to nuclease attack than its topological counterparts. Confocal microscope images reveal how the PLL and DNA remain bound post transfection. Quantification studies revealed that by 1 h post transfection 61% of SC-pDNA polyplexes were identified to be associated with the nucleus, in comparison to OC- (24.3%) and linear-pDNA polyplexes (3.5%) respectively. SC-pDNA polyplexes displayed the greatest transfection efficiency of 41% which dwarfed that of linear-pDNA polyplexes of 18.6%. Collectively these findings emphasize the importance of pDNA topology when complexed with PLL for gene delivery with the SC-form being a key pre-requisite.     

Synthesis, characterization and DNA interactions of 5,15-(4-pyridyl)-10,20-(pentafluorophenyl)porphyrin coordinated to two [Ru(bipy)2Cl] groups

A new porphyrin 5,15-(4-pyridyl)-10,20-(pentafluorophenyl)porphyrin (H₂DPDPFPP) and its diruthenium(II) analog ([trans-H₂(DPDPFPP)Ru₂(bipy)₄Cl₂(PF₆)₂]) have been synthesized and characterized. Electronic transitions associated with the porphyrin consist of an intense Soret band near 400 nm and four Q-bands from 500 nm to 650 nm. Coordination of two [Ru(bipy)₂Cl]⁺ groups, where bipy = 2,2′-bipyridine, to the pyridyl nitrogens of the porphyrin give additional electronic transitions associated with the bipy orbitals and metal to ligand charge transfer (MLCT) transitions associated with the Ru(II) and bipy orbitals. Reversible redox couples in the cathodic region occur at E_1/2 = −0.74 V and −1.21 V versus Ag/AgCl reference which are shifted to more positive potentials when the porphyrin is coordinated to the Ru(II) groups. Gel electrophoresis studies with linearized pUC18 indicate an interaction between the metallated porphyrin and DNA which is confirmed by UV/Vis titrations with calf thymus (CT) DNA giving a binding constant of ca. 10⁵ M⁻¹. When buffered, pH 7, solutions of circular plasmid DNA containing the ruthenium porphyrin are irradiated with a 50 W tungsten lamp cleavage of the DNA is observed.     

Determination of nanomolar uric and ascorbic acids using enlarged gold nanoparticles modified electrode

Individual and simultaneous determination of 50 nM uric acid (UA) and ascorbic acid (AA) using enlarged, citrate-stabilized gold nanoparticles (AuNPs) self-assembled to 2,5-dimercapto-1,3,4-thiadiazole (DMT) monolayer modified Au (Au/DMT) electrode by an amperometric method is described for the first time. Self-assembly of AuNPs on the electrode surface was confirmed by atomic force microscopy (AFM), attenuated total reflectance FT-IR and diffuse reflectance spectral measurements. The electron transfer reaction (ETR) of [Fe(CN)₆]^3−/4− was blocked at Au/DMT electrode, whereas it was restored with a peak separation of 200 mV after the attachment of AuNPs on the Au/DMT (Au/DMT/AuNPs) electrode, which was confirmed from the ETR of the [Fe(CN)₆]^3−/4− redox couple. When the self-assembled AuNPs were enlarged by hydroxylamine seeding, the ETR of [Fe(CN)₆]^3−/4− was improved significantly with a peak separation of 100 mV. Tapping mode AFM showed that the average size of the enlarged-AuNPs (E-AuNPs) was 50-70 nm. The E-AuNPs modified electrode catalyzes the oxidation of AA and UA, separates their voltammetric signals by 200 mV, and has excellent sensitivity towards AA and UA with a detection limit of 50 nM. The practical application of the modified electrode was demonstrated by measuring the concentration of UA in blood serum and urine.     

Investigation of riboflavin sensitized degradation of purine and pyrimidine derivatives of DNA and RNA under UVA and UVB

DNA and RNA undergo photodegradation in UVC (200-290 nm) due to direct absorption by the purine and pyrimidine bases. Limited effects are observed under UVB (290-320 nm) or UVA (320-400 nm). We have observed that an endogenous photosensitizer, riboflavin (RF), upon exposure to UVB or UVA can extensively damage the DNA and RNA bases. Guanine, uracil, thymine, adenine and cytosine were degraded by 100%, 82%, 60.4%, 46.3% and 10.3% under UVA (12 J) and by 100%, 54.1%, 38.9%, 42.2% and <1.0% under UVB (6 J), respectively. Guanosine and deoxyguanosine were degraded by 98 ± 1.0% and 80 ± 1.0% under UVA (4 J) and UVB (12 J), respectively. With an exception of GMP (53-82%), dGMP (51-88%) and to some extent TMP (3-4%) the remaining nucleosides and nucleotides were resistant to RF-induced photodecomposition. The photodegradation of G derivatives by RF was 2-fold higher than a well known photodynamic agent rose bengal. A comparison of the intensities of UVA and UVB sources used in this study with natural sunlight suggests that exposure with the latter along with an endogenous photosensitizer can have similar effects on DNA and RNA depending upon the duration of exposure.     

Electrochemical detection of short sequences of hepatitis C 3a virus using a peptide nucleic acid-assembled gold electrode

Development of an electrochemical DNA biosensor, using a gold electrode modified with a self-assembled monolayer composed of a peptide nucleic acid (PNA) probe and 6-mercapto-1-hexanol, is described. The sensor relies on covalent attachment of the14-mer PNA probe related to the hepatitis C virus genotype 3a (pHCV3a) core/E1 region on the electrode. Covalently self-assembled PNA could selectively hybridize with a complementary sequence in solution to form double-stranded PNA-DNA on the surface. The increase of peak current of methylene blue (MB), upon hybridization of the self-assembled probe with the target DNA in the solution, was observed and used to detect the target DNA sequence. Some hybridization experiments with noncomplementary oligonucleotides were carried out to assess whether the suggested DNA sensor responds selectively to the target. Diagnostic performance of the biosensor is described and the detection limit was found to be 5.7 × 10⁻¹¹ M with a relative standard deviation of 1.4% in phosphate buffer solution, pH 7.0. This sensor exhibits high reproducibility and could be used for detection of the target DNA for seven times after the regeneration process.     

The self-assembly, elasticity, and dynamics of cardiac thin filaments

Solutions of intact cardiac thin filaments were examined with transmission electron microscopy, dynamic light scattering (DLS), and particle-tracking microrheology. The filaments self-assembled in solution with a bell-shaped distribution of contour lengths that contained a population of filaments of much greater length than the in vivo sarcomere size (∼1 μm) due to a one-dimensional annealing process. Dynamic semiflexible modes were found in DLS measurements at fast timescales (12.5 ns-0.0001 s). The bending modulus of the fibers is found to be in the range 4.5-16 × 10⁻²⁷ Jm and is weakly dependent on calcium concentration (with Ca²⁺ ≥ without Ca²⁺). Good quantitative agreement was found for the values of the fiber diameter calculated from transmission electron microscopy and from the initial decay of DLS correlation functions: 9.9 nm and 9.7 nm with and without Ca²⁺, respectively. In contrast, at slower timescales and high polymer concentrations, microrheology indicates that the cardiac filaments act as short rods in solution according to the predictions of the Doi-Edwards chopsticks model (viscosity, η ∼ c³, where c is the polymer concentration). This differs from the semiflexible behavior of long synthetic actin filaments at comparable polymer concentrations and timescales (elastic shear modulus, G′ ∼ c^1.4, tightly entangled) and is due to the relative ratio of the contour lengths (∼30). The scaling dependence of the elastic shear modulus on the frequency (ω) for cardiac thin filaments is G′ ∼ ω^{3/4 ± 0.03}, which is thought to arise from flexural modes of the filaments.     

Cartilage aggrecan can undergo self-adhesion

Here it is reported that aggrecan, the highly negatively charged macromolecule in the cartilage extracellular matrix, undergoes Ca²⁺-mediated self-adhesion after static compression even in the presence of strong electrostatic repulsion in physiological-like solution conditions. Aggrecan was chemically end-attached onto gold-coated planar silicon substrates and gold-coated microspherical atomic force microscope probe tips (end radius R ≈ 2.5 μm) at a density (∼40 mg/mL) that simulates physiological conditions in the tissue (∼20-80 mg/mL). Colloidal force spectroscopy was employed to measure the adhesion between opposing aggrecan monolayers in NaCl (0.001-1.0 M) and NaCl + CaCl₂ ([Cl⁻] = 0.15 M, [Ca²⁺] = 0 - 75 mM) aqueous electrolyte solutions. Aggrecan self-adhesion was found to increase with increasing surface equilibration time upon compression (0-30 s). Hydrogen bonding and physical entanglements between the chondroitin sulfate-glycosaminoglycan side chains are proposed as important factors contributing to aggrecan self-adhesion. Self-adhesion was found to significantly increase with decreasing bath ionic strength (and hence, electrostatic double-layer repulsion), as well as increasing Ca²⁺ concentration due to the additional ion-bridging effects. It is hypothesized that aggrecan self-adhesion, and the macromolecular energy dissipation that results from this self-adhesion, could be important factors contributing to the self-assembled architecture and integrity of the cartilage extracellular matrix in vivo.     

The structure of DNA-DOPC aggregates formed in presence of calcium and magnesium ions: A small-angle synchrotron X-ray diffraction study

The structure of aggregates formed due to DNA interaction with dioleoylphosphatidylcholine (DOPC) vesicles in presence of Ca²⁺ and Mg²⁺ cations was investigated using synchrotron small-angle X-ray diffraction. For DOPC/DNA = 1:1 mol/base and in the range of concentration of the cation²⁺ 0-76.5 mM, the diffractograms show the coexistence of two lamellar phases: L^x phase with repeat distance d_Lx ∼ 8.26-7.39 nm identified as a phase where the DNA strands are intercalated in water layers between adjacent lipid bilayers, and L_DOPC phase with repeat distance d_DOPC ∼ 6.45-5.65 nm identified as a phase of partially dehydrated DOPC bilayers without any divalent cations and DNA strands. The coexistence of these phases was investigated as a function of DOPC/DNA molar ratio, length of DNA fragments and temperature. If the amount of lipid increases, the fraction of partially dehydrated L_DOPC phase is limited, depends on the portion of DNA in the sample and also on the length of DNA fragments. Thermal behaviour of DOPC + DNA + Ca²⁺ aggregates was investigated in the range 20-80 °C. The transversal thermal expansivities of both phases were evaluated.     

Light induced DNA scission by a luminescent mixed-ligand uranyl complex

Efficient cleavage of supercoiled pBR322 DNA by X-ray crystallographically characterized complex, [UO₂(phen)(aba)(OC₂H₅)] (phen = 1,10-phenanthroline; aba = 4-dimethylamino benzoate) has been observed on irradiation with UV (350 nm) or visible light without any external additives through a mechanistic pathway involving singlet oxygen. This complex having 1,10-phenanthroline as an intercalator/binder to supercoiled DNA and N,N-(dimethylamino)benzoate as a chromophore.     

Synthesis and biological studies of 4', 7, 8-trihydroxy-isoflavone metal complexes

A new series of complexes of a ligand 4′, 7, 8-trihydroxy-isoflavone with transition metal (zinc, copper, manganese, nickel, cobalt) and selenium have been synthesized and characterized with the aid of elemental analysis, IR, electron ionization mass spectrum (EI-MS) and ¹H NMR spectrometric techniques. The compounds were evaluated for their in vitro antibacterial activities and antitumor properties. The metal complexes were found to be more active than the free ligand. Investigation on the interaction between the complexes and calf-thymus DNA (CT DNA) showed that the absorbance of CT DNA increased and the maximum peak (λ_max = 260 nm) red-shifted, while the intensity of fluorescence spectra of Epstein-Bart DNA (EB-DNA) gradually weakened, which indicated that all of these metal complexes tightly combined with CT DNA.     

AFM study on the electric-field effects on supported bilayer lipid membranes

Electric-field induced changes in structure and conductivity of supported bilayer lipid membranes (SLM) have been studied at submicroscopic resolution using atomic force microscopy and electrochemical impedance spectroscopy. The SLMs are formed on gold surfaces modified with mixed self-assembled monolayers of a cholesterol-tether and 6-mercaptohexanol. At applied potentials of ≤−0.25 V versus standard hydrogen electrode, the conductance of the SLM increases and membrane areas of <150 nm in size are found to elevate from the surface up to 15 nm in height. To estimate the electric field experienced by the lipid membrane, electrowetting has been used to determine the point of zero charge of a 6-mercaptohexanol-modified surface (0.19 ± 0.13 V versus standard hydrogen electrode). The effects of electric fields on the structure and conductance of supported membranes are discussed.     

Transparent cellulose sheets as synthesis matrices for inorganic functional particles

Transparent cellulose sheets were prepared through tape-casting a solution of cellulose. Flexible, luminescent sheets were produced by adding europium trichloride to the casting solution and treating the sheets with an aqueous solution of ammonium fluoride. Scanning electron micrographs of the resulting sheets showed europium trifluoride particles with diameters from 200 nm to 500 nm. These were found by transmission electron microscopy to be agglomerates of crystallites in the size range of 10-20 nm. The structure of supercritically dried sheets was further assessed by small-angle X-ray scattering and suggests a preferred orientation of slightly elongated pores of roughly 12 nm in diameter. Evaluation of the emission characteristics of the sheets showed the band pattern between 580 nm and 700 nm typical for Eu³⁺ phosphors. Our developed process is a versatile tool for the fabrication of transparent cellulose structures with different shapes and various embedded functional particles.     

Magnetic single-enzyme nanoparticles with high activity and stability

Magnetic single-enzyme nanoparticles (SENs) encapsulated within a composite inorganic/organic polymer network were fabricated via the surface modification and in situ aqueous polymerization of separate enzyme molecule. The resultant nanoparticles were characterized by transmission electron microscope (TEM), Fourier transform infrared (FTIR) spectrometer and X-ray diffraction (XRD). These particles are almost spherical in shape and have a unique size of about 50 nm in diameter. Electrical and magnetic measurements reveal that the magnetic SENs have a conductivity of 2.7 × 10⁻³ S cm⁻¹, and are superparamagnetic with a saturation magnetization of 14.5 emu g⁻¹ and a coercive force of 60 Oe. Compared with free enzyme, encapsulated enzyme exhibits a strong tolerance to the variation of solution pH, high temperature, organic solvent and long-term storage, thus showing significantly enhanced enzyme performance and stability.     

2-Aminopurine/cytosine base pair containing oligonucleotides: fluorescence spectroscopy studies on DNA-polyamide binding

Studies on the binding of a triamide f-IPI (1) to its cognate sequence labeled with a 2-aminopurine (2AP or G^∗) group are described. ITC studies showed that f-IPI (1) bound to the cognate site (ACG^∗CGT) with only 3.5-fold lower affinity than binding to the unlabeled DNA (ACGCGT) (K_eq = 2 × 10⁷ and 7 × 10⁷ M⁻¹, respectively). Titration of f-IPI (1) to both sequences gave strong induced bands at 330 nm via circular dichroism studies. The compound also gave comparable ΔT_m values of 5.0 and 7.8 °C, respectively. These techniques also proved that the sequence selectivity of f-IPI (1) was uncompromised, as only limited binding to the non-cognate sequence ACCG^∗GT was observed. Fluorescence studies demonstrated a 2:1 ligand:DNA binding motif as anticipated, and indicated that the limit of detection for this technique was 20 μM DNA concentration. The results demonstrate that 2-aminopurine is a sufficient substitute for guanine in a G·C base pair useful in DNA binding studies.     

Molecular shape and binding force of Mycoplasma mobile’s leg protein Gli349 revealed by an AFM study

Recent studies of the gliding bacteria Mycoplasma mobile have identified a family of proteins called the Gli family which was considered to be involved in this novel and yet fairly unknown motility system. The 349 kDa protein called Gli349 was successfully isolated and purified from the bacteria, and electron microscopy imaging and antibody experiments led to the hypothesis that it acts as the “leg” of M. mobile, responsible for attachment to the substrate as well as for gliding motility. However, more precise evidence of the molecular shape and function of this protein was required to asses this theory any further. In this study, an atomic force microscope (AFM) was used both as an imaging and a force measurement device to provide new information about Gli349 and its role in gliding motility. AFM images of the protein were obtained revealing a complex structure with both rigid and flexible parts, consistent with previous electron micrographs of the protein. Single-molecular force spectroscopy experiments were also performed, revealing that Gli349 is able to specifically bind to sialyllactose molecules and withstand unbinding forces around 70 pN. These findings strongly support the idea that Gli349 is the “leg” protein of M. mobile, responsible for binding and also most probably force generation during gliding motility.     

Electrochemical biosensor for the detection of cauliflower mosaic virus 35 S gene sequences using lead sulfide nanoparticles as oligonucleotide labels

Lead sulfide (PbS) nanoparticles were synthesized in aqueous solution and used as oligonucleotide labels for electrochemical detection of the 35 S promoter from cauliflower mosaic virus (CaMV) sequence. The PbS nanoparticles were modified with mercaptoacetic acid and could easily be linked with CaMV 35 S oligonucleotide probe. Target DNA sequences were covalently linked on a mercaptoacetic acid self-assembled gold electrode, and DNA hybridization of target DNA with probe DNA was completed on the electrode surface. PbS nanoparticles anchored on the hybrids were dissolved in the solution by oxidation of HNO₃ and detected using a sensitive differential pulse anodic stripping voltammetric method. The detection results can be used to monitor the hybridization reaction. The CaMV 35 S target sequence was satisfactorily detected with the detection limit as 4.38 × 10⁻¹² mol/L (3σ). The established method extends nanoparticle-labeled electrochemical DNA analysis to specific sequences from genetically modified organisms with higher sensitivity and selectivity.     

Synthesis, double stranded DNA-binding and photocleavage studies of a functionalized ruthenium(II) complex with 7,7′-methylenedioxyphenyldipyrido[3,2-a:2′,3′-c]-phenazine

A new Ru(II) complex [Ru(phen)₂(mdpz)]²⁺ (phen = 1,10-phenanthroline, mdpz = 7,7′-methylenedioxyphenyl-dipyrido-[3,2-a:2′,3′-c]phenazine) has been synthesized and characterized in detail by elemental analysis, mass spectrometry and ¹H NMR spectroscopy. The interaction of the complex with calf thymus DNA was investigated by spectroscopic and viscosity measurements. The results suggest that the complex binds to DNA via an intercalative mode and serves as a molecular “light switch” for DNA. Moreover, the complex has been found to promote the photocleavage of plasmid DNA pBR322 under irradiation at 365 nm. The mechanism studies reveal that singlet oxygen (¹O₂) plays a significant role in the photocleavage.