Nanoparticle-based electrochemical detection of hepatitis B virus using stripping chronopotentiometry

A selective and sensitive gold nanoparticle-based electrochemical method for detection of hepatitis B virus DNA sequences was used. This method relies on the hybridization of amplified hepatitis B virus DNA strands with probes that are extended on paramagnetic beads. After separation of noncomplementary sequences, hybridized magnetic beads were treated with streptavidin-modified gold followed by silver enhancement. High selectivity and high sensitivity were obtained using electrochemical stripping detection of silver ions that were deposited on gold nanoparticles. With a signal/noise ratio of approximately 4.6, the detection limit was estimated to be 0.7ng/ml.     

A nucleic acid biosensor for the detection of a short sequence related to the hepatitis B virus using bis(benzimidazole)cadmium(II) dinitrate as an electrochemical indicator

A novel hybridization indicator, bis(benzimidazole)cadmium(II) dinitrate (Cd(bzim)(2)(NO(3))(2)), was utilized to develop an electrochemical DNA biosensor for the detection of a short DNA sequence related to the hepatitis B virus (HBV). The sensor relies on the immobilization and hybridization of the 21-mer single-stranded oligonucleotide from the HBV long repeat at the glassy carbon electrode (GCE). The hybridization between the probe and its complementary sequence as the target was studied by enhancement of the peak of the Cd(bzim)(2)(2+) indicator using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Numerous factors affecting the probe immobilization, target hybridization, and indicator binding reactions were optimized to maximize the sensitivity and speed of the assay time. With this approach, a sequence of the HBV could be quantified over the range from 1.49x10(-7)M to 1.06x10(-6)M, with a linear correlation of r=0.9973 and a detection limit of 8.4x10(-8)M. The Cd(bzim)(2)(2+) signal observed from the probe sequence before and after hybridization with a four-base mismatch containing sequence was lower than that observed after hybridization with a complementary sequence, showing good selectivity. These results demonstrate that the Cd(bzim)(2)(2+) indicator provides great promise for the rapid and specific measurement of the target DNA.     

Electrochemical nucleic acid hybridization biosensor based on poly(L-Aspartic acid)-modified electrode for the detection of short oligonucleotide sequences related to hepatitis C virus 1a

Abstract

This work describes, for the first time, the fabrication of poly(L-aspartic acid) (PAA) film modified pencil graphite electrode (PGE) for the detection of hepatitis C Virus 1a (HCV1a). The presence of PAA on the electrode surface can provide free carboxyl groups for covalent binding of biomolecules. The PGE surface was first coated with PAA via electropolymerization of the L-aspartic acid, and avidin was subsequently attached to the PAA modified electrode by covalent attachment. Biotinylated HCV1a probes were immobilized on avidin/PAA/PGE via avidin-biotin interaction. The morphology of PAA/PGE was examined using a scanning electron microscope. The hybridization events were monitored with square wave voltammetry using Meldola’s blue (MDB). Compared to non-complementary oligonucleotide sequences, when hybridization was carried out between the probe and its synthetic targets or the synthetic polymerase chain reaction analog of HCV1a, the highest MDB signal was observed. The linear range of the biosensor was 12.5 to 100?nM and limit of detection was calculated as 8.7?nM. The biosensor exhibited favorable stability over relatively long-term storage. All these results suggest that PAA-modified electrode can be used to nucleic acid biosensor application and electropolymerization of L-aspartic acid can be considered as a good candidate for the immobilization of biomolecules.     

Label-free electrochemical aptasensor for thrombin detection based on the nafion@graphene as platform

A sensitive label-free electrochemical aptasensor was successfully fabricated for thrombin detection with nafion@graphene as platform. With electrostatic interaction between nafion and methylene blue (MB), positive charged MB was successfully assembled on nafion@graphene modified electrode surface, which provided amounts of redox probes for electrochemical aptasensor. In the presence of thrombin, the thrombin aptamer (TBA) on the electrode surface would catch the target on the electrode interface, which made a barrier for electrons and inhibits the electro-transfer, resulting in the decreased differential pulse voltammetry signals of MB. As a result, the proposed approach showed a high sensitivity and a wider linearity to thrombin in the range 0.01–50 nM with a detection limit of 6 pM.     

Electrochemical detection of short sequences of hepatitis C 3a virus using a peptide nucleic acid-assembled gold electrode

Development of an electrochemical DNA biosensor, using a gold electrode modified with a self-assembled monolayer composed of a peptide nucleic acid (PNA) probe and 6-mercapto-1-hexanol, is described. The sensor relies on covalent attachment of the14-mer PNA probe related to the hepatitis C virus genotype 3a (pHCV3a) core/E1 region on the electrode. Covalently self-assembled PNA could selectively hybridize with a complementary sequence in solution to form double-stranded PNA-DNA on the surface. The increase of peak current of methylene blue (MB), upon hybridization of the self-assembled probe with the target DNA in the solution, was observed and used to detect the target DNA sequence. Some hybridization experiments with noncomplementary oligonucleotides were carried out to assess whether the suggested DNA sensor responds selectively to the target. Diagnostic performance of the biosensor is described and the detection limit was found to be 5.7 × 10⁻¹¹ M with a relative standard deviation of 1.4% in phosphate buffer solution, pH 7.0. This sensor exhibits high reproducibility and could be used for detection of the target DNA for seven times after the regeneration process.     

Designing primers from multiple sequences using matchup program to improve detection of hepatitis B virus by polymerase chain reaction

Traditionally primers for PCR detection of viruses have been selected from genomic sequence of single or representative viral strain. However, high mutation rate of viral genomes often results in failure in detecting viruses in clinical and environmental samples. Thus, it seems necessary to consider primers designed from multiple viral sequences in order to improve detection of viral variants. Matchup is a program intended to select universal primers from multiple sequences. We designed using Matchup program primer pairs for HBV detection from 691 full genomic HBV DNA sequences available from NCBI GenBank database. Thousands of primer candidates were initially extracted and these were sequentially filtered down to 5 primer pairs. These primer pairs were tested by PCR using 5 HBV Korean HBsAg(+) patient sera, and eventually one universal primer pair was selected and named MUW (multiple-universal-worldwide). This primer pair, 3 HBV reference primer pairs reported by others and 1 commercial primer pair were compared using 86 HBV HBsAg(+) sera from Korean and Vietnamese patients. The detection rate for MUW primer pair was 72.1%, much greater than those obtained by reference and commercial primers (32.5 to 40.7%). The superiority of MUW primer pair appeared to be correlated with the conserved sequences of the forward primer binding sites and primer quality score. These results suggest that the universal primers designed by the Matchup program from multiple sequences could be useful in detecting viruses from clinical samples.     

Label-free impedance detection of oligonucleotide hybridisation on interdigitated ultramicroelectrodes using electrochemical redox probes

The direct detection of oligodeoxynucleotide (ODN) hybridisation using electrochemical impedance spectroscopy was made on interdigitated array (IDA) gold (Au) ultramicroelectrodes manufactured by silicon technology. The immobilisation of single stranded ODNs (ssODNs) was accomplished by self-assembling of thiol-modified ODNs onto an Au-electrode surface. Faradaic impedance was measured in the presence of K(3)[Fe(CN)(6)]. Double strand formation was identified by a decrease of approximately 50% in impedance in the low frequency region in the presence of K(3)[Fe(CN)(6)], compared to the spectrum of single stranded ODN. The frequency dependent diffusion of Fe(CN)(6)(3-) ions through defects in the ODN monolayer determines the impedance of Au-ssODN surface. The influence of DNA intercalator methylene blue on the impedance of both, single and double strands, was examined along with K(3)[Fe(CN)(6)] and confirmed by cyclic voltammetry. The layer densities and the hybridisation have been further corroborated by chronoamperometric redox recycling of para-aminophenol (p-AP) in ELISA like experiments. It can be concluded, that a performed impedance spectroscopy did not change the layer density. The impedance spectroscopy at ultramicroelectrodes combined with faradaic redox reactions enhances the impedimetric detection of DNA hybridisation on IDA platforms.     

Label-free electrical detection of DNA hybridization for the example of influenza virus gene sequences

Microarrays based on DNA-DNA hybridization are potentially useful for detecting and subtyping viruses but require fluorescence labeling and imaging equipment. We investigated a label-free electrical detection system using electrochemical impedance spectroscopy that is able to detect hybridization of DNA target sequences derived from avian H5N1 influenza virus to gold surface-attached single-stranded DNA oligonucleotide probes. A 23-nt probe is able to detect a 120-nt base fragment of the influenza A hemagglutinin gene sequence. We describe a novel method of data analysis that is compatible with automatic measurement without operator input, contrary to curve fitting used in conventional electrochemical impedance spectroscopy (EIS) data analysis. A systematic investigation of the detection signal for various spacer molecules between the oligonucleotide probe and the gold surface revealed that the signal/background ratio improves as the length of the spacer increases, with a 12- to 18-atom spacer element being optimal. The optimal spacer molecule allows a detection limit between 30 and 100 fmol DNA with a macroscopic gold disc electrode of 1 mm radius. The dependence of the detection signal on the concentration of a 23-nt target follows a binding curve with an approximate 1:1 stoichiometry and a dissociation constant of KD=13+/-4 nM at 295 K.     

Data mining on DNA sequences of hepatitis B virus

Extraction of meaningful information from large experimental data sets is a key element in bioinformatics research. One of the challenges is to identify genomic markers in Hepatitis B Virus (HBV) that are associated with HCC (liver cancer) development by comparing the complete genomic sequences of HBV among patients with HCC and those without HCC. In this study, a data mining framework, which includes molecular evolution analysis, clustering, feature selection, classifier learning, and classification, is introduced. Our research group has collected HBV DNA sequences, either genotype B or C, from over 200 patients specifically for this project. In the molecular evolution analysis and clustering, three subgroups have been identified in genotype C and a clustering method has been developed to separate the subgroups. In the feature selection process, potential markers are selected based on Information Gain for further classifier learning. Then, meaningful rules are learned by our algorithm called the Rule Learning, which is based on Evolutionary Algorithm. Also, a new classification method by Nonlinear Integral has been developed. Good performance of this method comes from the use of the fuzzy measure and the relevant nonlinear integral. The nonadditivity of the fuzzy measure reflects the importance of the feature attributes as well as their interactions. These two classifiers give explicit information on the importance of the individual mutated sites and their interactions toward the classification (potential causes of liver cancer in our case). A thorough comparison study of these two methods with existing methods is detailed. For genotype B, genotype C subgroups C1, C2, and C3, important mutation markers (sites) have been found, respectively. These two classification methods have been applied to classify never-seen-before examples for validation. The results show that the classification methods have more than 70 percent accuracy and 80 percent sensitivity for most data sets, which are considered high as an initial scanning method for liver cancer diagnosis.     

Label-free electrochemical detection of DNA using ferrocene-containing cationic polythiophene and PNA probes on nanogold modified electrodes

A label-free electrochemical method for the detection of DNA-PNA hybridization using a water-soluble, ferrocene-functionalized polythiophene transducer and single-stranded PNA probes on the nanogold modified electrode is investigated. Nanogold modified electrodes can largely increase the immobilization amount of ss-PNA capture probe and lead to an increase of the electrical signal. The ferrocene-containing cationic polythiophene do not interact electrostatically with the PNA probes due to the absence of the anionic phosphate groups on the PNA probes. But after DNA-PNA hybridization, cationic polythiophene is adsorbed on the DNA backbone, giving a clear hybridization detection signal in differential pulse voltammetry (DPV). Very good discrimination against non-complementary DNA and four-base mismatch DNA is observed. These studies show that the proposed method can provide an alternative for expanding the range of detection methods available for DNA hybridization.     

Label-free and reagentless electrochemical detection of PCR fragments using self-assembled quinone derivative monolayer: application to Mycobacterium tuberculosis

We report a signal-on, label-free and reagentless electrochemical DNA biosensor, based on a mixed self-assembled monolayer of thiolated hydroxynaphthoquinone and thiolated oligonucleotide. Electrochemical changes resulting from hybridization were evidenced with oligonucleotide targets (as models), as well as with polymerase chain reaction (PCR) products related to different lineages of Mycobacterium tuberculosis strains. With pure oligonucleotides, this system achieves high sensitivity (～300 pM of DNA target, i.e. 30 fmol in a 100 μL sample) and excellent selectivity, allowing to detect a single mismatch on a sequence of 20 bases. With PCR products, current changes are specific to the bacterial strain from which the PCR fragment is produced. In addition, the sensor response is of the signal-on type, giving a positive signal change upon hybridization, and therefore does not suffer from false positive responses due to non-specific adsorption of DNA.     

Hepatitis B surface antigen levels and sequences of natural hepatitis B virus variants influence the assembly and secretion of hepatitis d virus

Various domains of hepatitis B surface antigen (HBsAg) are essential for the assembly and secretion of hepatitis D virus (HDV). This study investigated the influences of the levels and sequences of HBsAg of naturally occurring HBV variants on the assembly and secretion of HDV. Six hepatitis B virus (HBV)-producing plasmids (three genotype B and three genotype C) and six HBsAg expression plasmids that expressed various HBsAg levels were constructed from the sera of HDV-infected patients. These plasmids were cotransfected with six expression plasmids of HDV of genotype 1, 2, or 4 into the Huh-7 hepatoma cell line. Serum HBsAg and HBV DNA levels were correlated with HDV RNA levels and outcomes of chronic hepatitis D (CHD) patients. The secretion of genotype 1, 2, or 4 HDV generally correlated with HBsAg levels but not with HBV genotypes or HBV DNA levels. Swapping and residue mutagenesis experiments of HBsAg-coding sequences revealed that the residue Pro-62 in the cytosolic domain-I affects the assembly and secretion of genotype 2 and 4 HDV and not those of genotype 1. The pre-S2 N-terminal deletion HBV mutant adversely affects secretion of the three HDV genotypes. In patients, serum HDV RNA levels correlated with HBsAg levels but not with HBV DNA levels. Viremia of HDV or HBV correlated with poor outcomes. In conclusion, the assembly and secretion of HDV were influenced by the amounts and sequences of HBsAg. For an effective treatment of CHD, reduction of HBsAg production in addition to the suppression of HBV and HDV replication might be crucial.     

Label-free electrochemical immunosensor for the determination of fetoprotein based on core-shell-shell nanocomposite particles

A new approach toward the development of advanced immunosensors based on chemically functionalized core-shell-shell magnetic nanocomposite particles, and the preparation, characteristics, and measurement of relevant properties of the immunosensor useful for the detection of alpha-1-fetoprotein (AFP) in clinical immunoassays. The core-shell NiFe2O4/3-aminopropyltriethoxysilance (APTES) (NiFe2O4@APTES) was initially prepared by covalent conjugation, then gold nanoparticles were adsorbed onto the surface of NiFe2O4@APTES, and then anti-AFP molecules were conjugated on the gold nanoparticles. The core-shell-shell nanocomposite particles not only had the properties of magnetic nanoparticles, but also provided a good biocompatibility for the immobilization of biomolecules. The core-shell-shell nanostructure present good magnetic properties to facilitate and modulate the way it was integrated into a carbon paste. The analytical performance of the immunosensor was investigated by using an electrochemical method. Under optimal conditions, the resulting composite presents good electrochemical response for the detection of AFP, and exhibits wide linear range from 0.9 to 110 ng/mL AFP with a detection limit of 0.5 ng/mL. Moreover, the proposed immunosensors were used to analyze AFP in human serum specimens. Analytical results, obtained for the clinical serum specimen by the developed immunosensor, were in accordance with those assayed by the standard ELISA. Importantly, the proposed immunoassay system could be further developed for the immobilization of other antigens or biocompounds.     

Rapid detection of hepatitis B virus DNA level based on interval-point data fusion of infrared spectra

Hepatitis B is an infectious disease cause by the hepatitis B virus (HBV). In recent years, HBV-DNA level clinically gets more attention for its detailed information than other serological markers. Unfortunately, common clinical method for HBV-DNA level detection is limited for its hours consuming. This study combined infrared spectroscopy with machine learning to investigate the feasibility of near-infrared (NIR) and mid-infrared (MIR) spectra for rapid detection of HBV-DNA level. Based on partial least squares-discriminant analysis (PLS-DA) modeling method, the optimal NIR and MIR models and traditional data fusion models were constructed, respectively. Considering inequal weight between interval and point data in machine learning, interval-point data fusion method was used to compare with other traditional date fusion methods. The results of the study illustrate that interval-point data fusion of NIR and MIR spectra combined with PLS-DA modeling can provide a rapid method for HBV-DNA level detection.     

Enhanced chemiluminescence ELISA for the detection of antibody to hepatitis B virus surface antigen

A chemiluminescent enzyme linked immunosorbent assay (ELISA) for the detection of antibody to hepatitis B virus surface antigen (anti-HBs) in human serum has been developed. Polystyrene microtitre plates were coated with recombinant, yeast-derived hepatitis B surface antigen (rec-HBsAg). Patient serum samples and appropriate controls were added to the rec-HBsAg-coated wells and incubated to bind anti-HBs. The wells were then washed and a fluorescein isothiocyanate (FITC) conjugate of a human plasma-derived hepatitis B surface antigen (HBsAg) was added. Following incubation and further washing the bound FITC-labelled HBsAg was detected after addition of a horseradish peroxidase (HRP) conjugate of a monoclonal anti-FITC antibody and assaying for the enzyme. The activity of the HRP was measured using luminol and hydrogen peroxide as substrates and iodophenol as a chemiluminescence enhancer. The luminescence was recorded using a camera luminometer. Preliminary tests have shown the assay to be suitable for the detection of antibody in sera from both vaccinees and also from individuals with a past hepatitis B virus infection. The use of the FITC-anti-FITC system together with the measurement of a chemiluminescence signal makes possible the completion of this assay in a few hours. The assay has been shown to be both specific and sensitive and provides a permanent photographic record.     

Enhanced detection of human immunodeficiency virus type 1-specific T-cell responses to highly variable regions by using peptides based on autologous virus sequences

The antigenic diversity of human immunodeficiency virus type 1 (HIV-1) represents a significant challenge for vaccine design as well as the comprehensive assessment of HIV-1-specific immune responses in infected persons. In this study we assessed the impact of antigen variability on the characterization of HIV-1-specific T-cell responses by using an HIV-1 database to determine the sequence variability at each position in all expressed HIV-1 proteins and a comprehensive data set of CD8 T-cell responses to a reference strain of HIV-1 in infected persons. Gamma interferon Elispot analysis of HIV-1 clade B-specific T-cell responses to 504 overlapping peptides spanning the entire expressed HIV-1 genome derived from 57 infected subjects demonstrated that the average amino acid variability within a peptide (entropy) was inversely correlated to the measured frequency at which the peptide was recognized (P = 6 x 10(-7)). Subsequent studies in six persons to assess T-cell responses against p24 Gag, Tat, and Vpr peptides based on autologous virus sequences demonstrated that 29% (12 of 42) of targeted peptides were only detected with peptides representing the autologous virus strain compared to the HIV-1 clade B consensus sequence. The use of autologous peptides also allowed the detection of significantly stronger HIV-1-specific T-cell responses in the more variable regulatory and accessory HIV-1 proteins Tat and Vpr (P = 0.007). Taken together, these data indicate that accurate assessment of T-cell responses directed against the more variable regulatory and accessory HIV-1 proteins requires reagents based on autologous virus sequences. They also demonstrate that CD8 T-cell responses to the variable HIV-1 proteins are more common than previously reported.     

Nucleotide sequences in human chromosomal DNA from nonhepatic tissues homologous to the hepatitis B virus genome

DNA extracted from human nonhepatic tissues (placenta and kidney) have been digested with restriction endonucleases and examined by the Southern procedure with cloned 32P-labelled DNA of hepatitis B virus (HBV). In placental DNAs of women with the history of a hepatitis B infection and in one out of four cases of patients with no known HBV exposure or manifestation, HBV-related chromosomal nucleotide sequences were detected. The integration of HBV-related sequences was observed also in human kidney DNA. Moreover, in the placenta of women who had hepatitis B infection prior to delivery, unusual unintegrated forms of HBV have been found. We conclude that HBV sequences can be found not only in hepatic tissue but also in placental and kidney DNA, both of HBV-exposed and in one case even of a nonexposed patient.