Production and molecular characteristics of four groups of exopolysaccharides from submerged culture of Phellinus gilvus

AIMS: The objective of the present study was to determine the optimal culture conditions for the production of four groups of exopolysaccharides (EPSs) in Phellinus gilvus by submerged culture and to investigate their molecular properties by multi-angle laser-light scattering (MALLS) analysis. METHODS AND RESULTS: The optimal temperature and initial pH for the production of both mycelial biomass and EPSs in P. gilvus by submerged flask cultures were found to be 30 degrees C and pH 9.0, respectively. Glucose and corn steep powder were the most suitable carbon and nitrogen source for both mycelial biomass and EPS production. Optimal medium composition was determined to be glucose 30 g l-1, corn steep powder 5 g l-1, MgSO4 1.23 g l-1, KH2PO4 0.68 g l-1, and K2HPO4 0.87 g l-1. Four groups of EPSs (Fr-I, II, III, and IV) were obtained from the culture filtrates by gel filtration chromatography on Sepharose CL-4B and characterized by size exclusion chromatography (SEC) coupled with MALLS. The weight average molar mass (Mw) of Fr-I, Fr-II, Fr-III and Fr-IV were determined to be 8.628 x 106 (+/-129 420), 1.045 x 106 (+/-19 855), 61.09 x 104 (+/-1244), and 33.55 x 104 (+/-134) g mol-1, respectively. CONCLUSIONS: Under optimal culture conditions, the maximum EPS production in a 5-l stirred fermenter indicated 5.3 g l-1 after 11 days of fermentation. The SEC/MALLS analysis revealed that Fr-I, which has extremely high molecular weight, was presumably an aggregate of complex polysaccharides forming a compact globular shape; whereas Fr-II was nearly spherical, Fr-III and Fr-IV were rod-like chains in an aqueous solution. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first report on the production of high amounts of EPSs from liquid-culture of the basidiomycete, P. gilvus. The SEC/MALLS approach used in this study could be useful in providing greater insight into the characterization of the mushroom polysaccharides without carrying out elaborate fractionation procedures prior to analysis.     

A Review of: “Progress in Separation and Purification Vol. 3, E. S. Perry and C. J,van Oss,eds., Willy/Intersciencc,New York, 1970; xi + 316 pares; hard cover; 515.95”

The optimal culture conditions of exopolysaccharides (EPS) production in submerged culture medium by Pleurotus geesteranus 5 ^# were determined using an orthogonal matrix method. The optimal defined medium (per liter) was 60.0 g maltose, 5.0 g tryptone, 1 mM NaCl, 5 mM KH₂PO₄, and initial pH 6.0 at 28 °C. In the optimal culture medium, the maximum EPS production was 16.97 g/L in a shake flask. Two groups of EPSs (designated as Fr-I and Fr-II) were obtained from the culture filtrates by size exclusion chromatography (SEC), and their molecular characteristics were examined by a multiangle laser-light scattering (MALLS) and refractive index (RI) detector system. The approximate weight-average molar masses of the Fr-I and Fr-II of EPS were determined to be 3.263 × 10⁴ and 5.738 × 10³ g/mol, respectively. The low values of polydispersity ratio (1.176 and 1.124 for Fr-I and Fr-II, respectively) of EPSs mean that these EPS molecules exist much less dispersed in aqueous solution without forming large aggregates. Furthermore, the experiments in vitro indicated that P. geesteranus 5^# EPS exhibit high antitumor and antioxidative effects.     

Characterization and antioxidant activity for exopolysaccharide from submerged culture of Boletus aereus

Three polysaccharide fractions (designated as Fr-I, Fr-II and Fr-III) were successfully purified from the crude exopolysaccharide (EPS) produced from submerged culture of Boletus aereus by gel filtration chromatography on Sepharose CL-6B. The size exclusion chromatography/multi-angle laser light scattering (SEC/MALLS) system showed that the average molecular weights (Mws) of these three fractions were 1.365 × 10⁶, 1.048 × 10⁵ and 2.471 × 10⁴ g/mol, respectively. The SEC/MALLS also revealed that the molecular conformation of the Fr-I was a random coil, with Fr-II being a rigid rod in aqueous solution. Moreover, monosaccharide composition analysis indicated that Fr-I was mainly composed of glucose, while both of Fr-II and Fr-III were mainly composed of mannose and glucose. Then, FT-IR spectral analysis of the purified EPS revealed prominent characteristic groups. Furthermore, thermo gravimetric analysis (TGA) indicated the degradation temperature of the Fr-I (170 °C) was higher than those of Fr-II (156 °C) and Fr-III (155 °C). Finally, on the basis of the antioxidant activity test in vitro, Fr-I exhibited the highest antioxidant ability among these samples, which might be attributed to the monosaccharide composition and molecular weight in the EPS fraction.     

Medium optimization, molecular characterization, and bioactivity of exopolysaccharides from Pleurotus eryngii

An optimal medium for exopolysaccharides (EPS) production was obtained through one-factor-at-a-time method and response surface methodology. Under optimal culture medium, the maximum EPS concentration in shake flask was 5.16 g/l. Two groups of EPSs (designated as Fr-I and Fr-II) were obtained from the culture filtrates by size exclusion chromatography/multiangle laser light scattering, and the weight average molar masses (M _w) of Fr-I and Fr-II were determined to be 4.098 × 10⁴ and 1.114 × 10⁴ g/mol, respectively. The molecular confirmation of Fr-I was revealed to be a rigid rod form in aqueous solution. Moreover, monosaccharide composition and characteristic groups were investigated by GC and Fourier transform infrared, respectively. Finally, pharmacology experiment in vitro indicated EPS Fr-II of Pleurotus eryngii exhibited higher antioxidant and antitumor abilities than Fr-I, which might be attributed to the different molecular weights and chemical compositions in the EPS fraction.     

Apoptosis of human hepatocarcinoma (HepG2) and neuroblastoma (SKN-SH) cells induced by polysaccharides-peptide complexes produced by submerged mycelial culture of an entomopathogenic fungus Cordyceps sphecocephala

Three different polysaccharide-peptide complexes (PPC, named as Fr-I, Fr-II, and Fr-III) were produced by submerged mycelial culture of an entomopathogenic fungus Cordyceps sphecocephala, and their anticancer activities were investigated in human hepatocarcinoma (HepG2) and neuroblastoma (SK-N-SH) cells. The highest inhibitory effects of PPC on both HepG2 and SK-N-SH cells were achieved with Fr-I, whereas Fr-III with low molecular mass showed lower inhibition effects. Interestingly, the inhibitory effects of the three fractions were increased after protease digestion, suggesting that the inhibitory effects resulted mainly from the carbohydrate moiety, at least in the case of Fr-II and Fr-III, of PPC. The results of DNA fragmentation in PPC-induced apoptotic cells were confirmed by both DNA ladder assay and comet assay. Our investigation also showed that PPC-induced apoptosis of both cancer cells was associated with intracellular events including DNA fragmentation, activation of caspase-3, and modulation of Bcl-2 and Bax. We conclude that PPC has potential as a novel therapeutic agent for the treatment of both HepG2 and SK-N-SH cancer cells without any cytotoxicity against normal cells.     

Optimization of a liquid medium for beauvericin production in <Emphasis Type="Italic">Fusarium redolens</Emphasis> Dzf2 mycelial culture

Beauvericin (BEA) is a proven and potent antibiotic compound useful for bio-control and a potential antifungal and anticancer agent for human. This study was to evaluate and optimize the nutrient medium for BEA production in mycelial liquid culture of a high BEA-producing fungus Fusarium redolens Dzf2 isolated from a medicinal plant. Among various organic and inorganic carbon and nitrogen sources, glucose and peptone were found the most favorable for the F. redolens Dzf2 mycelial growth and BEA production. Through a Plackett-Burman screening test on a basal medium, glucose, peptone, and medium pH were identified as the significant factors for mycelial growth and BEA production. These factors were optimized through central composite design of experiments and response surface methodology, as 49.0 g/L glucose, 13.0 g/L peptone and pH 6.6, yielding 198 mg/L BEA (versus 156 mg/L in the basal medium). The BEA yield was further increased to 234 mg/L by feeding 10 g/L glucose to the culture during exponential phase. The results show that F. redolens Dzf2 mycelial fermentation is a feasible and promising process for production of BEA.     

Factors affecting mycelial biomass and exopolysaccharide production in submerged cultivation of Antrodia cinnamomea using complex media

Submerged cultures were used to identify growth-limiting nutrients by Antrodia cinnamomea strains. The mycelial biomass and EPS production by A. cinnamomea BCRC 35396 were markedly higher than other A. cinnamomea strains. A relatively high C/N ratio was favorable for both the mycelial growth (5.41 g/l) and EPS production (0.55 g/l); the optimum ratio was 40. The glucose was available utilized preferentially for mycelial growth, rather than for EPS production. Flushing the culture medium with nitrogen had a stimulating effect on both mycelial growth and EPS production. In addition, peptone, yeast extract and malt extract appeared to be important and significant component for EPS production. Phosphate ion, magnesium ion and thiamine were probably not essential for mycelial growth. By optimizing the effects of additional nutrition, the results showed that 5% (w/v) glucose, 0.8% (w/v) peptone, 0.8% (w/v) yeast extract, 0.8% (w/v) malt extract, 0.03% (w/v) KH2PO4, 0.1% (w/v) MgSO4 .7H2O and 0.1% (w/v) thiamine could lead to the maximum production of EPS (1.36 g/l).     

Optimization of culture conditions and medium components for the production of mycelial biomass and exo-polysaccharides with Cordyceps militaris in liquid culture

Both crude exo-biopolymers and mycelial biomass, produced by liquid culture of Cordyceps species, are believed to possess several potential health benefits. As a result of its known biological activities, Cordyceps militaris has been extensively characterized in regards to potential medicinal applications. However, optimized liquid culture conditions for enhanced polysaccharide productivity have yet to be developed, which is a necessary step for industrial applications. Therefore, in this study, the liquid culture conditions were optimized for maximal production of mycelial biomass and exo-polysaccharide (EPS) by C. militaris. The effects of medium composition, environmental factors, and C/N ratio were investigated. Among these variables 80 g, glucose; 10 g, yeast extract; 0.5 g, MgSO₄·7H₂O; and 0.5 g, KH₂PO₄ in 1 L distilled water were found to be the most suitable carbon, nitrogen, and mineral sources, respectively. The optimal temperature, initial pH, agitation, and aeration were determined to be 24°C, uncontrolled pH, 200 rpm, and 1.5 vvm, respectively. Under these optimal conditions, mycelial growth in shake flask cultures and 5 L jar bioreactors was 29.43 and 40.60 g/L, respectively, and polysaccharide production in shake flask cultures and 5 L jar bioreactors was 2.53 and 6.74 g/L, respectively.     

Study of mycelial growth and bioactive polysaccharide production in batch and fed-batch culture of Grifola frondosa

The fermentation of Grifola frondosa was investigated in the shake flasks and a 5-L jar fermenter in batch and fed-batch modes. In the shake-flask experiments, the preferable mycelial growth and exopolysaccharide (EPS) production was observed at relatively low pH; maltose and glucose were preferred carbon sources for high mycelial production. The EPS was doubled after 13 d of cultivation when glucose was increased from 2% to 4%. Yeast extract (YE) (0.4%) in combination with corn steep powder (CSP) (0.6%) and YE (0.8%) in combination with CSP (1.2%) were preferred nitrogen sources for high mycelial production and EPS production, respectively. All plant oils tested significantly stimulate cell growth of G. frondosa but they failed to enhance EPS production. The EPS products usually consisted of two fractions of different molecular sizes varied by the plant oils used. The fed-batch fermentation by glucose feeding was performed when the glucose concentration in the medium was lower than 0.5% (5g/L), which greatly enhanced the accumulation of mycelial biomass and EPS; the mycelial biomass and EPS were 3.97g/L and 1.04g/L before glucose feeding, which reached 8.23g/L and 3.88g/L at 13 d of cultivation. In contrast, the mycelial biomass and EPS in the batch fermentation were 6.7g/L and 3.3g/L at 13 d of cultivation.     

Optimization of exopolysaccharide overproduction by Lactobacillus confusus in solid state fermentation under high salinity stress

It is believed that high concentrations of sodium chloride (NaCl) suppress the biosynthesis of exopolysaccharide (EPS) in lactic acid bacteria (LAB). Nevertheless, overproduction of EPSs due to high salinity stress in solid state fermentation performed on an agar surface was demonstrated in this study using a response surface methodology via a central composite design (CCD). Under optimized conditions with NaCl 4.97% and sucrose 136.5 g/L at 40.79 h of incubation, the EPS yield was 259% (86.36 g/L of EPS), higher than the maximum yield produced with the modified MRS medium containing only 120 g/L of sucrose without NaCl (33.4 g/L of EPS). Biosynthesis of EPS by Lactobacillus confusus TISTR 1498 was independent of biomass production. Our results indicated that high salinity stress can enhance EPS production in solid state fermentation.     

Effects of culture conditions on the mycelial growth and bioactive metabolite production in submerged culture of Cordyceps militaris

The influence of initial pH value, various nitrogen sources, plant oils, and modes of propagation (shake-flask and static culture) on the production of biomass, exopolysaccharide (EPS), adenosine and, in particular, cordycepin, by Cordyceps militaris CCRC 32219 were investigated. Optimal conditions for mycelial growth, EPS and cordycepin production were observed at relatively low pH. Amongst organic sources, yeast extract (YE) was favorable for EPS and cordycepin production, while corn steep powder (CSP) was favorable for adenosine production. A lower C/N ratio was favorable for adenosine and cordycepin production; however, too low a C/N ratio led to diminished production. All plant oils tested stimulate mycelial growth and EPS production of C. militaris, but they did not show much effect on the adenosine and cordycepin production. A two-stage fermentation process by combining shake-flask fermentation with static culture significantly enhanced cordycepin production. A Box–Behnken experimental design was employed to optimize the production of cordycepin, which showed that the optimum conditions to produce cordycepin by C. militaris CCRC 32219 were at pH 6, YE concentration of 45 g/l and 8.0 day of the shake culture followed by 16 days of the static culture. Under the optimized conditions, the maximum production (2214.5 mg/l) of cordycepin was obtained, which is much higher than those reported up to date.     

Factors influencing the production of water-soluble endopolysaccharides and exopolysaccharides from Lentinus lepideus and their effects on immune cytokine production

An efficient method to produce water-soluble polysaccharides from Lentinus lepideus is described. The productivity of both endopolysaccharides (PPS) and exopolysaccharides (EPS) was compared under various culture conditions. The effect of treating their own PPS and EPS on immune cytokine production was also studied in relation to culture factors. High yield production of EPS required moderate culture temperature (25 degrees ) as well as long culture period (16-20 days). In contrast, PPS production required high culture temperature (30 degrees ) and short culture period ( days). Most of the carbon sources did not affect polysaccharides and mycelial production except for sucrose. Immune cytokine levels in the EPS treatment varied among carbon sources or culture periods. PPS did not appear to affect much on the production of cytokines, regardless of the culturing factors, except for the culture period. These results suggest that the optimal culture conditions for L. lepideus vary according to culture purposes, and different culture conditions should be used for different targets including mycelial biomass, EPS, and PPS. Whereas the immunomodulating activity of EPS appeared to be affected by culture conditions in L. lepideus, that of PPS did not.     

Production of exopolysaccharides by submerged mycelial culture of <Emphasis Type="Italic">Grifola frondosa</Emphasis> TFRI1073 and their antioxidant and antiproliferative activities

The exopolysaccharide (EPS) extract of a newly screened Grifola frondosa TFRI1073 was evaluated antioxidant activity, including superoxide anion scavenging activity and reducing power, and the antiproliferative activities by using lung (A549 cells) and breast (MDA-MD-231 cells) cancer cell line. The exopolysaccharide of G. frondosa plays the important role on antioxidant and antiproliferative activities. Nutritional requirements for mycelial biomass and EPS production by G. frondosa were studied. Flushing the culture medium with carbon sources has a stimulating effect on both mycelial biomass and EPS production. In addition, nitrogen sources appeared to be an important and significant component for mycelial biomass. Vitamins were probably not essential for mycelial biomass and EPS production. Inorganic salts appeared to have a significant effect on both mycelial biomass and EPS productions. The effect of phosphate ion on mycelial biomass was better than on EPS production. The information generated in this study will facilitate physiological research of a newly screened G. frondosa TFRI1073, helping to develop the exopolysaccharide of a new dietary supplement and functional food from G. frondosa.     

Enhanced production of exopolysaccharides by fed-batch culture of Ganoderma resinaceum DG-6556

The objectives of this study were to optimize submerged culture conditions of a new fungal isolate, Ganorderma resinaceum, and to enhance the production of bioactive mycelial biomass and exopolysaccharides (EPS) by fed-batch culture. The maximum mycelial growth and EPS production in batch culture were achieved in a medium containing 10 g/l glucose, 8 g/l soy peptone, and 5 mM MnCl(2) at an initial pH 6.0 and temperature 31 degrees C. After optimization of culture medium and environmental conditions in batch cultures, a fed-batch culture strategy was employed to enhance production of mycelial biomass and EPS. Five different EPS with molecular weights ranging from 53,000 to 5,257,000 g/mole were obtained from either top or bottom fractions of ethanol precipitate of culture filtrate. A fed-batch culture of G. resinaceum led to enhanced production of both mycelial biomass and EPS. The maximum concentrations of mycelial biomass (42.2 g/l) and EPS (4.6 g/l) were obtained when 50 g/l of glucose was fed at day 6 into an initial 10 g/l of glucose medium. It may be worth attempting with other mushroom fermentation processes for enhanced production of mushroom polysaccharides, particularly those with industrial potential.     

Optimization of submerged culture condition for the production of mycelial biomass and exopolysaccharides by Agrocybe cylindracea

The optimization of submerged culture conditions and nutritional requirements was studied for the production of exopolysaccharide (EPS) from Agrocybe cylindracea ASI-9002 using the statistically based experimental design in a shake flask culture. Both maximum mycelial biomass and EPS were observed at 25 degrees C. The optimal initial pH for the production of mycelial biomass and EPS were found to be pH 4.0 and pH 6.0, respectively. Subsequently, optimum concentration of each medium component was determined using the orthogonal matrix method. The optimal combination of the media constituents for mycelial growth was as follows: maltose 80 g/l, Martone A-1 6 g/l, MgSO4 x 7H2O 1.4 g/l, and CaCl2 1.1 g/l; for EPS production: maltose 60 g/l, Martone A-1 6 g/l, MgSO4 x 7H2O 0.9 g/l, and CaCl2 1.1 g/l. Under the optimal culture condition, the maximum EPS concentration achieved in a 5-l stirred-tank bioreactor indicated 3.0 g/l, which is about three times higher than that at the basal medium.     

Effects of C/N ratio and trace elements on mycelial growth and exo-polysaccharide production of <Emphasis Type="Italic">Tricholoma matsutake</Emphasis>

Although its demand increased greatly due to the volatile strong flavor and bioactive molecules, little information has been about the cultural characteristics of Tricholoma matsutake. In this study, we investigated the optimal medium composition of liquid culture with the goal of shortening the culture period, and to maximize polysaccharide production and mycelial growth. From these experiments we found that the optimal medium contained 40 g/L, glucose; 30 g/L, yeast extract; 1.5 g/L, KH₂PO₄; and 1 g/L MgSO₄·7H₂O. In flask culture, the maximum mycelial growth and polysaccharide production were 22.45 and 5.3 g/L, which were about 9 and 3 g/L higher than that at the basal medium, respectively.     

Optimisation of submerged culture conditions for the production of mycelial biomass and exopolysaccharide byPleurotus nebrodensis

The optimisation of submerged culture conditions and nutritional requirements was studied for the production of exopolysaccharide (EPS) fromPleurotus nebrodensis. The optimal temperature and initial pH for both mycelial growth and EPS production in shake flask cultures were 25 °C and 8.0, respectively. Maltose was found the most suitable carbon source for both mycelial biomass and EPS production. Yeast extract was favourable nitrogen source for both mycelial biomass and EPS production. Optimum concentration of each medium component was determined using the orthogonal matrix method. The optimal combination of the media constituents for mycelial growth and EPS production was as follows: 200 g l^?1 bran, 25 g l^?1 maltose, 3 g l^?1 yeast extract, 1 g l^?1 KH₂PO₄, 1 g l^?1 MgSO₄ 7H₂O. Under the optimal conditions, the mycelial biomass (4.13 g l^?1) and EPS content (2.40 g l^?1) ofPleurotus nebrodensis was 2.3 and 3.6 times compared to the control with basal medium respectively.     

Optimization of submerged culture requirements for the production of mycelial growth and exopolysaccharide by Cordyceps jiangxiensis JXPJ 0109

AIMS: The objective of the present study was to investigate the optimal culture requirements for mycelial growth and exopolysaccharide production by Cordyceps jiangxiensis JXPJ 0109 in submerged culture. METHODS AND RESULTS: The effects of medium ingredients (i.e. carbon and nitrogen sources, and growth factor) and other culture requirements (i.e. initial pH, temperature, etc.) on the production of mycelia and exopolysaccharide were observed using a one-factor-at-a-time method. More suitable culture requirements for mycelial growth and exopolysaccharide production were proved to be maltose, glycerol, tryptone, soya bean steep powder, yeast extract, medium capacity 200 ml in a 500-ml flask, agitation rate 180 rev min(-1), seed age 4-8 days, inoculum size 2.5-7.5% (v/v), etc. The optimal temperatures and initial pHs for mycelial growth and exopolysaccharide production were at 26 degrees C and pH 5 and at 28 degrees C and pH 7, respectively, and corresponding optimal culture age were observed to be 8 and 10 days respectively. According to the primary results of the one-factor-at-a-time experiments, the optimal medium for the mycelial growth and exopolysaccharide production were obtained using an orthogonal layout method to optimize further. Herein the effects of medium ingredients on the mycelial growth of C. jiangxiensis JXPJ 0109 were in the order of yeast extract > tryptone > maltose > CaCl2 > glycerol > MgSO4 > KH2PO4 and the optimal concentration of each composition was 15 g maltose (food-grade), 10 g glycerol, 10 g tryptone, 10 g yeast extract, 1 g KH2PO4, 0.2 g MgSO4, and 0.5 g CaCl2 in 1 l of distilled water, while the order of effects of those components on exopolysaccharide production was yeast extract > maltose > tryptone > glycerol > KH2PO4 > CaCl2 > MgSO4, corresponding to the optimal concentration of medium was as follows: 20 g maltose (food-grade), 8 g glycerol, 5 g tryptone, 10 g yeast extract, 1 g KH2PO4, and 0.5 g CaCl2 in 1 l of distilled water. CONCLUSIONS: Under the optimal culture requirements, the maximum exopolysaccharide production reached 3.5 g l(-1) after 10 days of fermentation, while the maximum production of mycelial growth achieved 14.5 g l(-1) after 8 days of fermentation. SIGNIFICANCE AND IMPACT OF THE STUDY: This is the first report on the submerged culture requirements for mycelial growth and exopolysaccharide in C. jiangxiensis, and this two-step optimization strategy in this study can be widely applied to other microbial fermentation processes.     

Exopolysaccharide production and mycelial growth in an air-lift bioreactor using Fomitopsis pinicola

For effective exopolysaccharide production and mycelial growth by a liquid culture of Fomitopsis pinicola in an air-lift bioreactor, the culture temperature, pH, carbon source, nitrogen source, and mineral source were initially investigated in a flask. The optimal temperature and pH for mycelial growth and exopolysaccharide production were 25degrees C and 6.0, respectively. Among the various carbon sources tested, glucose was found to be the most suitable carbon source. In particular, the maximum mycelial growth and exopolysaccharide production were achieved in 4% glucose. The best nitrogen sources were yeast extract and malt extract. The optimal concentrations of yeast extract and malt extract were 0.5 and 0.1%, respectively. K2HPO4 and MgSO4 x 7H2O were found to be the best mineral sources for mycelial growth and exopolysaccharide production. In order to investigate the effect of aeration on mycelial growth and exopolysaccharide production in an air-lift bioreactor, various aerations were tested for 8 days. The maximum mycelial growth and exopolysaccharide production were 7.9 g/l and 2.6 g/l, respectively, at 1.5 vvm of aeration. In addition, a batch culture in an air-lift bioreactor was carried out for 11 days under the optimal conditions. The maximum mycelial growth was 10.4 g/l, which was approximately 1.7-fold higher than that of basal medium. The exopolysaccharide production was increased with increased culture time. The maximum concentration of exopolysaccharide was 4.4 g/l, which was about 3.3-fold higher than that of basal medium. These results indicate that exopolysaccharide production increased in parallel with the growth of mycelium, and also show that product formation is associated with mycelial growth. The developed model in an air-lift bioreactor showed good agreement with experimental data and simulated results on mycelial growth and exopolysaccharide production in the culture of F pinicola.     

Improved simultaneous production of mycelial biomass and polysaccharides by submerged culture of <Emphasis Type="Italic">Hericium erinaceum</Emphasis>: optimization using a central composite rotatable design (CCRD)

The aim of this study was to optimize the culture medium used for the mycelial growth and production of intracellular polysaccharides (IPS) and exopolysaccharides (EPS) in a submerged culture of Hericium erinaceum. Of the various factors examined, including carbon and nitrogen sources, vitamins, mineral elements, and initial pH, those that proved to have a significant effect were then tested using a 2⁴ central composite rotatable design (CCRD). Under the optimal culture conditions, the maximal yield of biomass reached 14.24 ± 0.45 g l⁻¹ and was 1.85-fold higher than in the basal medium. The kinetics of EPS biosynthesis in a bioreactor showed that although the highest yield of EPS (2.75 ± 0.27 g l⁻¹) could be obtained on day 8, the process of biosynthesizing high molecular weight polysaccharides proceeded until the depletion of the carbon source in the medium (after 14 days of cultivation). Our results could be very helpful in the large-scale production of bioactive polysaccharides from H. erinaceum.