Development of a localized surface plasmon resonance-based gold nanobiosensor for the determination of prolactin hormone in human serum

A localized surface plasmon resonance immunoassay has been developed to determine prolactin hormone in human serum samples. Gold nanoparticles were synthesized, and the probe was prepared by electrostatic adsorption of antibody on the surfaces of gold nanoparticles. The pH and the antibody-to-gold nanoparticle ratio, as the factors affecting the probe functions, were optimized. The constructed nanobiosensor was characterized by dynamic light scattering. The sensor was applied for the determination of prolactin antigen concentration based on the amount of localized surface plasmon resonance peak shift. A linear dynamic range of 1–40 ng ml⁻¹, a detection limit of 0.8 ng ml⁻¹, and sensitivity of 10 pg ml⁻¹ were obtained. Finally, the nanobiosensor was applied for the determination of prolactin in human control serum sample.     

Gold Nanoring Arrays for Near Infrared Plasmonic Biosensing

Gold nanoring array surfaces that exhibit strong localized surface plasmon resonances (LSPR) at near infrared (NIR) wavelengths from 1.1 to 1.6 μm were used as highly sensitive real-time refractive index biosensors. Arrays of gold nanorings with tunable diameter, width, and spacing were created by the nanoscale electrodeposition of gold nanorings onto lithographically patterned nanohole array conductive surfaces over large areas (square centimeters). The bulk refractive index sensitivity of the gold nanoring arrays was determined to be up to 3,780 cm⁻¹/refractive index unit by monitoring shifts in the LSPR peak by FT-NIR transmittance spectroscopy measurements. As a first application, the surface polymerization reaction of dopamine to form polydopamine thin films on the nanoring sensor surface from aqueous solution was monitored with the real-time LSPR peak shift measurements. To demonstrate the utility of the gold nanoring arrays for LSPR biosensing, the hybridization adsorption of DNA-functionalized gold nanoparticles onto complementary DNA-functionalized gold nanoring arrays was monitored. The adsorption of DNA-modified gold nanoparticles onto nanoring arrays modified with mixed DNA monolayers that contained only 0.5 % complementary DNA was also detected; this relative surface coverage corresponds to the detection of DNA by hybridization adsorption from a 50 pM solution.

     

Design of Localized Surface Plasmon Resonance (LSPR) Biosensor for Immunodiagnostic of E. coli O157:H7 Using Gold Nanoparticles Conjugated to the Chicken Antibody

E. coli O157:H7 is one of the most important pathogens in food-borne diseases and is the main cause of the pseudo pandemic development of hemorrhagic colitis and hemolytic uremic syndrome. Also E. coli O157:H7 is the most common serotype of Shiga-toxin-producing E. coli. Traditional methods for detecting E. coli O157:H7 are expensive, time-consuming, and less sensitive. A method with high sensitivity and high-resolution optical detection is utilizes the LSPR property of spherical gold nanoparticles (GNP). In this work, we constructed a novel nano-bio probe to detect E. coli O157:H7 by synthesizing citrate gold nanoparticle conjugated (non-covalent bond) with specific chicken anti-E. coli O157:H7 antibody (IgY) by changing the pH of the nanoparticles’ environment. UV-visible and DLS methods were used to confirm the bonding between the antibody and nanoparticles and the LSPR sensitivity of the nano-bio probe was evaluated by ELISA method. We could optically detect this bacterium in less than 2 h by measuring the LSPR band λ max shifts of GNPs. The sensitivity of this novel biosensor was determined by about 10 CFU/ml, using the LSPR property of spherical gold nanoparticles. So that, the LSPR λ max red shifted from 530 to 543 nm in presence of 10 CFU bacterium. In conclusion, this nano biosensor can be used to detect this important pathogen among the clinical specimens.

     

Localized Surface Plasmon Resonance (LSPR)-Based Nanobiosensor for Methamphetamin Measurement

Aptamers are DNA or RNA single-stranded molecules that bind specifically to target molecules with high affinity. Function of nucleic acid aptamers is based on organized tertiary structure of them that is related to primary sequence, length of nucleic acid molecule, and environmental conditions. Herein, a localized surface plasmon resonance (LSPR) nanobioprobe has been developed based on specific aptamer-conjugated gold nanoparticles for rapid detection of methamphetamine. Detection of methamphetamine was studied via monitoring the gold nanoparticles (GNPs) LSPR band alterations in the presence of different concentrations. The covalent conjugation has been confirmed with FT-IR spectroscopy, and size alterations of gold nanoparticles before and after the conjugation state were monitored using dynamic light scattering (DLS) technique. The results show high affinity of aptamer to methamphetamine. Moreover, the results show conjugated aptamer with GNP in different concentrations of methamphetamine that contribute to color changes that is visible with unaided eye. Also, 14 nm LSPR shift was seen after conjugation of aptamer with GNP. Nanoparticle diameter after conjugation with aptamer was increased from 30 to 91 nm and decreased after incubation with methamphetamine (due to folding) from 91 to 84 nm. Detection limit of this designed nanoprobe is 500 nM. Plasmonic nanoparticle-based nanobioprobe is a new field for development of sensitive detection systems.

     

Label-free electrochemical immunosensor based on Nile blue A-reduced graphene oxide nanocomposites for carcinoembryonic antigen detection

In this article, a novel, label-free, and inherent electroactive redox immunosensor for carcinoembryonic antigen (CEA) based on gold nanoparticles (AuNPs) and Nile blue A (NB) hybridized electrochemically reduced graphene oxide (NB–ERGO) is proposed. The composite of NB–graphene oxide (NB–GO) was prepared by π–π stacking interaction. Then, chronoamperometry was adopted to simultaneously reduce HAuCl₄ and nanocomposites of NB–GO for synthesizing AuNPs/NB–ERGO. The immunosensor was fabricated by capturing CEA antibody (anti-CEA) at this nanocomposite modified electrode. The immunosensor determination was based on the fact that, due to the formation of antigen–antibody immunocomplex, the decreased response currents of NB were directly proportional to the concentrations of CEA. Under optimal conditions, the linear range of the proposed immunosensor was estimated to be from 0.001 to 40 ng ml⁻¹ and the detection limit was estimated to be 0.00045 ng ml⁻¹. The proposed immunosensor was used to determine CEA in clinical serum samples with satisfactory results. The proposed method may provide promising potential application in clinical immunoassays with the properties of facile procedure, stability, high sensitivity, and selectivity.     

Clinical application of a novel sliver nanoparticles biosensor based on localized surface plasmon resonance for detecting the microalbuminuria

In order to explore the clinical application of the nanobiosensor based on localized surface plasmon resonance (LSPR), we used our LSPR biosensor to detect the microalbuminuria in this work. The sliver nanoparticles were fabricated by using nanosphere lithography. The anti-human albumin antibody was immobilized on the sensor surface by amine coupling method. The different concentrations of commercial albumin and albumin in urine samples from three mild preeclampsia patients were determined according to the peak of LSPR extinction spectra. Under optimum conditions, our results showed that the biosensor displayed a detection limit of 1 ng/ml and wide dynamic range of 1 ng/ml to 1 μg/ml. Furthermore, the microalbuminuria of three patients was determined by our biosensor within a short assay time, without sample purification. This biosensor proposed herein is easy to prepare and could be used for low-cost, rapid, label-free, and sensitive screening of the microalbuminuria. This approach provides a promising platform for developing clinical diagnostic applications.     

Investigation of the Plasmonic Interaction of Gold Nanoparticles Toward Plasmonic Photothermal Therapeutics

Plasmonic interaction of nanoparticles located in close proximity, embedded in breast tissue, is simulated for estimating the optical characteristics like optical absorption cross-section, plasmonic wavelength as well as full-width half maxima (FWHM). The computations are done for the monomers, homodimers, and heterodimers of spherical and rod-shaped gold nanoparticles considering various interparticle spacings for gold nanospheres and the interparticle spacing as well as the orientation for gold nanorods (GNRs). The results indicate that for the spherical dimer, with the change in interparticle spacing from 1 to 20 nm, the peak absorption cross-section decreases by 43%. Whereas for the GNRs, the absorption cross-section increases/decreases, within 9–18%, depending on the homodimer or heterodimer configuration. Furthermore, secondary peaks for the absorption cross-section are obtained within wavelengths of 630–940 nm due to antibonding modes for GNR heterodimers. For GNR heterodimer located end-to-end, this secondary peak for the absorption cross-section appears at 780 nm irrespective of interparticle spacing within 1–5 nm. The absorption coefficient is considerably dependent on the configuration and proximity of GNRs located within the tissue. While FWHM is not significantly influenced by GNRs configuration and interparticle spacing. For interparticle spacing from 1 to 20 nm, the plasmonic wavelength shifts by 38 nm for the spherical dimer and by 35–86 nm for various GNR dimers. The findings of this study are useful for plasmonic photothermal therapeutics as the heat generation is governed by the resulting absorption cross-section due to plasmonic coupling of the closely spaced and different orientations of the nanoparticles.

     

Determination of collagen type IV by Surface Plasmon Resonance Imaging using a specific biosensor

Serum collagen type IV (COLIV) is a promising tumor marker. High COLIV concentrations have been found in the serum of patients with colorectal, gastric, lung, liver and breast cancers. The aim of this work was to develop a biosensor for use with the Surface Plasmon Resonance Imaging (SPRI) technique for COLIV determination. The biosensor consists of glass covered with gold and immobilized monoclonal mouse anti-human collagen type IV antibody via cysteamine linker. The biosensor works selectively within a dynamic response range between 10 and 300 ng mL⁻¹, with LOD 2.4 ng mL⁻¹ and LOQ 8 ng mL⁻¹. The precision of determination is 4.7% at a 150 ng mL⁻¹ COLIV spike and 8.0% at a 20 ng mL⁻¹ spike, with recoveries of 101% and 106% respectively. A 100-fold excess of collagen I, albumin, laminin and fibronectin is tolerated. The average COLIV blood plasma concentration of healthy donors determined by the developed method was 69 ± 10 ng mL⁻¹, while the median of six results available in the literature was approximately 80 ng mL⁻¹. The average COLIV blood plasma concentration of breast cancer patients was 360 ± 68 ng mL⁻¹, showing the high potential of COLIV as a marker of this type of cancer.     

An ultrasensitive electrochemical genosensor for Brucella based on palladium nanoparticles

Palladium nanoparticles were potentiostatically electrodeposited on a gold surface at a highly negative potential. The nanostructure, as a transducer, was utilized to immobilize a Brucella-specific probe and the process of immobilization and hybridization was detected by electrochemical methods. The proposed method for detection of the complementary sequence and a non-complementary sequence was applied. The fabricated genosensor was evaluated for the assay of the bacteria in the cultured and human samples with and without PCR. The genosensor could detect the complementary sequence with a sensitivity of 0.02 μA dm³ mol⁻¹, a linear concentration range of 1.0 × 10⁻¹² to 1.0 × 10⁻¹⁹ mol dm⁻³, and a detection limit of 2.7 × 10⁻²⁰ mol dm⁻³.     

Simultaneous detection of two tumor markers using silver and gold nanoparticles decorated carbon nanospheres as labels

In this work, a multiplexed electrochemical immunosensor was developed for sensitive detection of carcinoembryonic antigen (CEA) and α-fetoprotein (AFP) using silver nanoparticles (Ag NPs) or gold nanoparticles (Au NPs) coated-carbon nanospheres (CNSs) as labels. CNSs were employed as the carrier for the immobilization of nanoparticles (Ag NPs or Au NPs), thionine (Thi), and secondary antibodies (Ab₂) due to their good monodispersity and uniform structure. Au NPs reduced graphene oxide (rGO) nanocomposites were used as sensing substrate for assembling two primary antibodies (Ab₁). In the presence of target proteins, two labels were attached onto the surface of the rGO/Au NPs nanocomposites via a sandwich immunoreaction. Two distinguishable peaks, one at +0.16 V (corresponding to Ag NPs) and another at −0.33 V (corresponding to Thi), were obtained in differential pulse voltammetry (DPV). The peak difference was approximately 490 mV, indicating that CEA and AFP can be simultaneously detected in a single run. Under optimal conditions, the peak currents were linearly related to the concentrations of CEA or AFP in the range of 0.01–80 ng ml⁻¹. The detection limits of CEA and AFP were 2.8 and 3.5 pg ml⁻¹, respectively (at a signal-to-noise ratio of 3). Moreover, when the immunosensor was applied to serum samples, the results obtained were in agreement with those of the reference method, indicating that the immunosensor would be promising in the application of clinical diagnosis and screening of biomarkers.     

A novel electrochemical biosensor for selective determination of mercury ions based on DNA hybridization

An electrochemical biosensor was developed for Hg²⁺ determination based on DNA hybridization. In the presence of Hg²⁺, the target and probe DNAs with thymine–thymine (T–T) mismatches could hybridize by forming T–Hg²⁺–T complex. This induced DNA hybridization led to the decrease in reduction peak currents of ethyl green (EG) as electroactive label, which could be used for determination of Hg²⁺. The difference in the value of the peak currents of EG before and after DNA hybridization (ΔI) was linear with the concentration of Hg²⁺ in the range of 9.0 × 10⁻¹¹–1.0 × 10⁻⁹ M. The detection limit was 3.08 × 10⁻¹¹ M.     

Localized Surface Plasmon Resonance (LSPR) Biosensor for the Protein Detection

In this paper, we investigate the ability of the gold nanorods (GNRs) to detect some proteins and demonstrate their potential to be used as plasmonic nanobiosensors. The GNRs were synthesized by a two-step seed-mediated growth procedure at room temperature. Firstly, a seed solution of gold nanoparticles was synthesized in the presence of cetyltrimethylammonium bromide surfactant and, subsequently, incorporated with appropriate amount of silver nitrate and tetrachloroauric acid solutions to grow GNRs with average length of 50 nm and diameter of 14 nm. We study the interaction of GNRs with proteins whose molecular weight varies from 6.5 up to 75 kDa. We investigate the resulting solutions by means of UV–vis absorption spectroscopy to determine the effect of the proteins characteristics on the shift of the localized surface plasmon resonance (LSPR). We show that for the case when proteins are in large excess compared to the GNRs concentration, whatever the protein is, the LSPR shift is constant and does not depend on the protein molecular weight. Moreover, we have been able to demonstrate that the sensitivity of such LSPR sensor is around 10^–9 M/nm on a concentration range from 10^–10 to 10^–8 M. Some comparison with finite-difference time-domain simulations have also shown that the number of proteins adsorbed at the GNRs surface is around 40.     

An electrochemical aptasensor electrocatalyst for detection of thrombin

This work reports a novel signal amplification strategy based on three-dimensional ordered macroporous C₆₀-poly(3,4-ethylenedioxythiophene)-1-butyl-3-methylimidazolium hexafluorophosphate (3DOM C₆₀-PEDOT-[BMIm][BF₆]) for ultrasensitive detection of thrombin by cascade catalysis of Au-PEDOT@SiO₂ microspheres and alcohol dehydrogenase (ADH). Au-PEDOT@SiO₂ microspheres were constructed not only as nanocarriers to anchor the large amounts of secondary thrombin aptamers but also as nanocatalysts to catalyze the oxidation of ethanol efficiently. Significantly, the electrochemical signal was greatly enhanced based on cascade catalysis: First, ADH catalyzed the oxidation of ethanol to acetaldehyde with the concomitant generation of NADH in the presence of β-nicotinamide adenine dinucleotide hydrate (NAD⁺). Then, gold nanoparticles (AuNPs) as nanocatalysts could effectively catalyze NADH to produce NAD⁺ with the help of PEDOT as redox probe. Under the optimal conditions, the proposed aptasensor exhibits a linear range of 2 × 10⁻¹³ to 2 × 10⁻⁸ M with a low detection limit of 2 × 10⁻¹⁴ M for thrombin detection and shows high sensitivity and good specificity.     

Whole serum BSA antibody screening using a label-free biophotonic nanoparticle array

Bovine serum albumin antibodies (aBSA) have been screened from whole leporine anti serum on a biophotonic array. The array was initially printed with seed gold nanoparticles into a 96-spot configuration, and 130-nm gold nanoparticles were synthesised in situ on the surface of each spot. The gold nanoparticle surface was then functionalized with the proteins bovine serum albumin (BSA), fibrinogen, and immunoglobulin G (IgG) and with the amino acid glycine. The concentration of aBSA in the whole serum was determined using a kinetic analysis of the time-dependent light scattering from the nanoparticles. The aBSA-BSA kinetic parameters derived from the array are k_a = (1.3 ± 0.3) × 10⁵ M⁻¹ s⁻¹, k_d = (4 ± 2) × 10⁻⁴ s⁻¹, and K_D = 3 nM, which compare favorably with those from continuous gold surfaces. The ultimate sensitivity of the array reader to the bulk refractive index (RI) is 1 × 10⁻⁴ refractive index units (RIU), corresponding to 1 μg ml⁻¹ for aBSA. The nanoparticles appear to be more sensitive than the continuous gold surface to the aBSA binding event from whole serum, and this is interpreted in terms of the difference in RI contrast in the plasmon fields.     

Theoretical Study of the Anchoring Influence on Plasmonic Resonance Tunability of Metallic Nanoparticles Embedded in a Liquid Crystal Cell

In this paper, the localized surface plasmon resonance (LSPR) peak position of an ordered gold nanoparticles array embedded in a nematic liquid crystal (LC) media is investigated using finite-difference time-domain method. The influence of the anchoring effects between nematic LC molecules and glass substrate on the shift of LSPR wavelength is taken into account, and results are compared with the case of a perfect alignment of the LC molecules.     

One-step preparation of antibody and oligonucleotide dual-labeled gold nanoparticle bio-probes and their properties

A novel method of one-step preparation of dual-labeled gold nanoparticle bio-probes was established by the electrostatic adsorption and the covalent bonding of gold nanoparticles with antibodies and thiol-modified oligonucleotides, respectively. Characterization of probes, the coverage and activity of antibodies and oligonucleotides on probe surfaces were detected. The results indicated that the gold nanoparticles labeled with antibodies and oligonucleotides possess good bioactivity and the coverage of oligonucleotide and antibody on a dual-labeled gold nanoparticle bio-probe was (92 ± 20) and (8 ± 3), respectively. The preparative method is simple and stable. The dual-labeled gold nanoparticle bio-probes have an application value in detection of ultramicro protein.     

Surface Plasmon Coupling Effect of Gold Nanoparticles with Different Shape and Size on Conventional Surface Plasmon Resonance Signal

The labeling strategy with gold nanoparticles for the conventional surface plasmon resonance (SPR) signal enhancement has been frequently used for the sensitive determination of small molecules binding to its interaction partners. However, the influence of gold nanoparticles with different size and shape on SPR signal is not known. In this paper, three kinds of gold nanoparticles, namely nanorods, nanospheres, and nanooctahedrons with different size, were prepared and used to investigate their effects on the conventional SPR signal at a fixed excitation wavelength 670 nm. It was found that the SPR signal (i.e., resonant angle shift) was varied with the shapes and sizes of gold nanoparticles in suspension at a fixed concentration due to their different plasmon absorbance bands. For gold nanorods with different longitudinal absorbance bands, three conventional SPR signal regions could be clearly observed when the gold nanorod suspensions were separately introduced onto the SPR sensor chip surface. One region was the longitudinal absorbance bands coinciding with or close to the SPR excitation wavelength that suppressed the SPR angle shift. The second region was the longitudinal absorbance bands at 624 to 639 and 728 to 763 nm that produced a moderate increase on the SPR resonant angle shift. The third region was found for the longitudinal absorbance bands from 700 to 726 nm that resulted in a remarkable increase in the SPR angle shift responses. This phenomenon can be explained on the basis of calculation of the correlation of SPR angle shift response with the gold nanorod longitudinal absorbance bands. For nanospheres and nanooctahedrons, the SPR angle shift responses were found to be particle shape and size dependent in a simple way with a sustaining increase when the sizes of the nanoparticles were increased. Consequently, a guideline for choosing gold nanoparticles as tags is suggested for the SPR determination of small molecules with binding to the immobilized interaction partners.     

Fluorescein-labeled “arch-like” DNA probes for electrochemical detection of DNA on gold nanoparticle-modified gold electrodes

In the present study, a gold nanoparticle-modified gold electrode (nanogold electrode) was used to develop a novel fluorescein electrochemical DNA biosensor based on a target-induced conformational change. The nanogold electrode was obtained by electrodepositing gold nanoparticles onto a bare gold electrode. This modification not only immobilized probe oligonucleotides, but also adsorbed fluorescein onto the surface of the gold nanoparticles to form an “arch-like” structure. This article compares the electrochemical signal changes caused by the hybridization of “arch-like” DNA on nanogold electrode and linear DNA on bare gold electrode. The results showed that the adsorption effect of nanogold can enhance the sensitivity of the sensor. The linear range of target ssDNA is from 2.0 × 10⁻⁹ M to 2.0 × 10⁻⁸ M with a correlation coefficient of 0.9956 and detection limit (3σ) of 7.10 × 10⁻¹⁰ M. Additionally, the specificity and hybridization response of this simple sensor were investigated.     

Determination of nanomolar uric and ascorbic acids using enlarged gold nanoparticles modified electrode

Individual and simultaneous determination of 50 nM uric acid (UA) and ascorbic acid (AA) using enlarged, citrate-stabilized gold nanoparticles (AuNPs) self-assembled to 2,5-dimercapto-1,3,4-thiadiazole (DMT) monolayer modified Au (Au/DMT) electrode by an amperometric method is described for the first time. Self-assembly of AuNPs on the electrode surface was confirmed by atomic force microscopy (AFM), attenuated total reflectance FT-IR and diffuse reflectance spectral measurements. The electron transfer reaction (ETR) of [Fe(CN)₆]^3−/4− was blocked at Au/DMT electrode, whereas it was restored with a peak separation of 200 mV after the attachment of AuNPs on the Au/DMT (Au/DMT/AuNPs) electrode, which was confirmed from the ETR of the [Fe(CN)₆]^3−/4− redox couple. When the self-assembled AuNPs were enlarged by hydroxylamine seeding, the ETR of [Fe(CN)₆]^3−/4− was improved significantly with a peak separation of 100 mV. Tapping mode AFM showed that the average size of the enlarged-AuNPs (E-AuNPs) was 50-70 nm. The E-AuNPs modified electrode catalyzes the oxidation of AA and UA, separates their voltammetric signals by 200 mV, and has excellent sensitivity towards AA and UA with a detection limit of 50 nM. The practical application of the modified electrode was demonstrated by measuring the concentration of UA in blood serum and urine.     

Electrochemical immunosensor based on Pd–Au nanoparticles supported on functionalized PDDA-MWCNT nanocomposites for aflatoxin B1 detection

This paper reports a label-free electrochemical immunosensor for the determination of aflatoxin B1 (AFB1), which is based on a gold electrode modified by a biocompatible film of carbon nanotubes/poly(diallyldimethylammoniumchloride)/Pd–Au nanoparticles (CNTs/PDDA/Pd–Au). The nanocomposite was characterized by transmission electron microscopy and the electrochemical behavior of modified electrodes was investigated by cyclic voltammetry. The CNTs/PDDA/Pd–Au nanocomposites film showed good electron transfer ability, which ensured high sensitivity to detect AFB1 in a range from 0.05 to 25 ng mL⁻¹ with a detection limit of 0.03 ng mL⁻¹ obtained at 3σ (where σ is the standard deviation of the blank solution, n = 10). The proposed immunosensor provides a simple tool for AFB1 detection. This strategy can be extended to any other antigen detection by using the corresponding antibodies.