Cardiovascular Effects of Implanted Acrylic Bone Cement

A pilot study has shown that there is usually but not invariably a fall in systemic arterial blood pressure within 90 seconds of implanting acrylic cement into the femoral shaft during hip arthroplasty. There is usually no change in arterial blood pressure on implanting acrylic cement into the acetabulum. The observed hypotension may be due to absorption of monomer or additives into the circulation, but the role of other factors needs investigation.     

Modelling heat transfer in a bone-cement-prosthesis system

The heat transfer in a general bone-cement-prosthesis system was modelled. A quantitative understanding of the heat transfer and the polymerization kinetics in the system is necessary because injury of the bone tissue and the mechanical properties of the cement have been suggested to be effected by the thermal and chemical history of the system. The mathematical model of the heat transfer was based on first principles from polymerization kinetics and heat transfer, rather than certain in vitro observed properties, which has been the common approach. Our model was valid for general three-dimensional geometries and an arbitrary bone cement consisting of an initiator and monomer. The model was simulated for a cross-section of a hip with a potential femoral stem prosthesis and for a cement similar to Palacos R. The simulations were conducted by using the finite element method. These simulations showed that this general model described an auto accelerating heat production and a residual monomer concentration, which are two phenomena suggested to cause bone tissue damage and effect the mechanical properties of the cement.     

The influence of cement mantle thickness and stem geometry on fatigue damage in two different cemented hip femoral prostheses

Experimental models can be used for pre-clinical testing of cemented and other type of hip replacements. Total hip replacement (THR) failure scenarios include, among others, cement damage accumulation and the assessment of accurate stress and strain magnitudes at the cement mantle interfaces (stem-cement and cement-bone) can be used to predict mechanical failure. The aseptic loosening scenario in cemented hip replacements is currently not fully understood, and methods of evaluating medical devices must be developed to improve clinical performance. Different results and conclusions concerning the cement micro-cracking mechanism have been reported.The aim of this study was to verify the in vitro behavior of two cemented femoral stems with respect to fatigue crack formation. Fatigue crack damage was assessed at the medial, lateral, anterior and posterior sides of the Lubinus SPII and Charnley stems. All stems were loaded and tested in stair climbing fatigue loading during one million cycles at 2 Hz. After the experiments each implanted synthetic femur was sectioned and analyzed. We observed more damage (cracks per area) for the Lubinus SPII stem, mainly on the proximal part of the cement mantle. The micro-cracking formation initiated in the stem–cement interface and grew towards the direction of cortical bone of the femur.Overall, the cement–bone interface seems to be crucial for the success of the hip replacement. The Charnley stem provoked more damage on the cement–bone interface. A failure index (maximum length of crack/maximum thickness of cement) considered was higher for the cement–stem interface of the Lubinus SPII stem. For a cement mantle thickness higher than 5 mm, cracking initiated at the cement–bone interface and depended on the opening canal process (reaming procedure and instrumentation). The analysis also showed that fatigue-induced damage on the cement mantle, increasing proximally, and depended on the axial position of the stem. The cement thickness is an important factor for the success of THR and this study evidenced that cement thickness higher than 2 mm apparently does not affect the mechanical behavior of the cement mantel and induce more crack formation on the cement–bone interface.     

A Genetic Predictive Model for Canine Hip Dysplasia: Integration of Genome Wide Association Study (GWAS) and Candidate Gene Approaches

Canine hip dysplasia is one of the most prevalent developmental orthopedic diseases in dogs worldwide. Unfortunately, the success of eradication programs against this disease based on radiographic diagnosis is low. Adding the use of diagnostic genetic tools to the current phenotype-based approach might be beneficial. The aim of this study was to develop a genetic prognostic test for early diagnosis of hip dysplasia in Labrador Retrievers. To develop our DNA test, 775 Labrador Retrievers were recruited. For each dog, a blood sample and a ventrodorsal hip radiograph were taken. Dogs were divided into two groups according to their FCI hip score: control (A/B) and case (D/E). C dogs were not included in the sample. Genetic characterization combining a GWAS and a candidate gene strategy using SNPs allowed a case-control population association study. A mathematical model which included 7 SNPs was developed using logistic regression. The model showed a good accuracy (Area under the ROC curve = 0.85) and was validated in an independent population of 114 dogs. This prognostic genetic test represents a useful tool for choosing the most appropriate therapeutic approach once genetic predisposition to hip dysplasia is known. Therefore, it allows a more individualized management of the disease. It is also applicable during genetic selection processes, since breeders can benefit from the information given by this test as soon as a blood sample can be collected, and act accordingly. In the authors’ opinion, a shift towards genomic screening might importantly contribute to reducing canine hip dysplasia in the future. In conclusion, based on genetic and radiographic information from Labrador Retrievers with hip dysplasia, we developed an accurate predictive genetic test for early diagnosis of hip dysplasia in Labrador Retrievers. However, further research is warranted in order to evaluate the validity of this genetic test in other dog breeds.     

Failure prediction of the total hip prosthesis system

The mechanical failure of the prosthesis-cement-femur system is analyzed by using a two-dimensional finite element model. The strain energy density (SED) criterion is applied to locate potential failure sites in the PMMA and prosthesis stem for five different prosthesis positions.

Medial and lateral failure sites in the proximal regions of the cement are found to be the most sensitive to prosthesis position. According to the SED criterion, these are the weakest regions of the cement. Additional bilateral failure sites are also located at the distal end of the prosthesis, but are less likely to fail. The overall structural integrity of the total hip system is found to be adequate for the ideal case considered herein. In practice, the combination of energy concentration coupled with imperfections such as voids and cracks in the cement are potential sites of failure initiation.

On the basis of clinical evidence on cement and prosthesis stem fracture, local reductions in the cement elastic modulus were introduced into the finite element model in order to model cement defects. The bilateral reduction of modulus by 40% in the cement adjacent to the distal portion of the prosthesis stem can lead to an increase of the strain energy density by 19%.     

Cement flow during impaction allografting: a finite element analysis

Cement intrusion into cancellous or impacted bone is not well understood. We adopted an engineering mechanics approach to predict the effect of surgical variables on the cement intrusion into impacted cancellous bone, used for the revision of failed total hip replacement with the impaction allografting technique. Specifically, a three-dimensional finite element model was used to determine the effects of cement viscosity, the magnitude and duration of pressurization, and the distribution of the porosity along the femur on cement intrusion. The overall averaged mean intrusion depth difference between the finite element model prediction and the cadaveric measurements was 1.1mm. The depth of penetration increased with higher pressurization pressure, duration of pressurization, and earlier stem insertion (lower viscosity), but maintained a similar profile. The distribution of the porosity along the femur determined the intrusion profile. Cement viscosity, the applied pressure or the duration of the pressurization can be adjusted to limit the cement volume injected into the medullary canal and therefore prevent the cement from reaching the endosteal surface.     

Residual stresses at the stem-cement interface of an idealized cemented hip stem

During the operation of total hip arthroplasty, when the cement polymerizes between the stem implant and the bone, residual stresses are generated in the cement. The purpose of this study was to determine whether including residual stresses at the stem-cement interface of cemented hip implants affected the cement stress distributions due to externally applied loads. An idealized cemented hip implant subjected to bending was numerically investigated for an early post-operative situation. The finite element analysis was three-dimensional and used non-linear contact elements to represent the debonded stem-cement interface. The results showed that the inclusion of the residual stresses at the interface had up to a 4-fold increase in the von Mises cement stresses compared to the case without residual stresses.     

Use of an absorbable membrane to position biologically inductive materials in the periprosthetic space of cemented joints

A device is presented that positions ultrahigh molecular weight polyethylene (UHMWPE) debris against periprosthetic bone surfaces. This can facilitate the study of aseptic loosening associated with cemented joint prostheses by speeding the appearance of this debris within the periprosthetic space. The device, composed of a 100 microm thick bioabsorbable membrane impregnated with 1.4 x 10(9) sub-micron particles of UHMWPE debris, is positioned on the endosteum of the bone prior to the insertion of the cemented orthopedic implant. An in vitro pullout study and an in vivo canine pilot study were performed to investigate its potential to accelerate "time to aseptic loosening" of cemented prosthetic joints. Pullout studies characterized the influence of the membrane on initial implant fixation. The tensile stresses (mean+/-std.dev.) required to withdraw a prosthesis cemented into canine femurs with and without the membrane were 1.15+/-0.3 and 1.54+/-0.01 MPa, respectively; these findings were not significantly different (p > 0.4). The in vivo pilot study, involving five dogs, was performed to evaluate the efficacy of the debris to accelerate loosening in a canine cemented hip arthroplasty. Aseptic loosening and lameness occurred within 12 months, quicker than the 30 months reported in a retrospective clinical review of canine hip arthroplasty.     

Possibilities of avoiding an intra-femoral increase in pressure during hip revision surgery]

An earlier experimental study carried out by us revealed an increase in intrafemoral pressure during removal of cement in hip revision arthroplasty. This increase is greater while removing cement from the distal femoral shaft. Maximum pressure increases occurred while removing the medullary plug (cement stopper), and the measured pressure of more than 150 mmHg is associated with an increased risk of fat embolism. The present study shows that this phenomenon can be avoided through the use of cannulated instruments.     

Differential genetic regulation of canine hip dysplasia and osteoarthritis

Background

Canine hip dysplasia (HD) is a common polygenic trait characterized by hip malformation that results in osteoarthritis (OA). The condition in dogs is very similar to developmental dysplasia of the human hip which also leads to OA.

Methodology/Principal Findings

A total of 721 dogs, including both an association and linkage population, were genotyped. The association population included 8 pure breeds (Labrador retriever, Greyhounds, German Shepherd, Newfoundland, Golden retriever, Rottweiler, Border Collie and Bernese Mountain Dog). The linkage population included Labrador retrievers, Greyhounds, and their crosses. Of these, 366 dogs were genotyped at ∼22,000 single nucleotide polymorphism (SNP) loci and a targeted screen across 8 chromosomes with ∼3,300 SNPs was performed on 551 dogs (196 dogs were common to both sets). A mixed linear model approach was used to perform an association study on this combined association and linkage population. The study identified 4 susceptibility SNPs associated with HD and 2 SNPs associated with hip OA.

Conclusion/Significance

The identified SNPs included those near known genes (PTPRD, PARD3B, and COL15A1) reported to be associated with, or expressed in, OA in humans. This suggested that the canine model could provide a unique opportunity to identify genes underlying natural HD and hip OA, which are common and debilitating conditions in both dogs and humans.     

Microdamage accumulation in the cement layer of hip replacements under flexural loading.

Mechanical fatigue of bone cement leading to damage accumulation is implicated in the loosening of cemented hip components. Even though cracks have been identified in autopsy-retrieved mantles, damage accumulation by continuous growth and increase in number of microcracks has not yet been demonstrated experimentally. To determine just how damage accumulation occurs in the cement layer of a hip replacement, a physical model of the joint was used in an experimental study. The model regenerates the stress pattern found in the cement layers whilst at the same time allowing visualisation of microcrack initiation and growth. In this way the gradual process of damage accumulation can be determined. Six specimens were tested to 5 million cycles and a total of 1373 cracks were observed. It was found that, under the flexural loading allowed by the model, the majority of cracks come from pores in the bulk cement and not from the interfaces. Furthermore, the lateral and medial sides have statistically different damage accumulation behaviours, and pre-load cracks significantly accelerate the damage accumulation process. The experimental results confirm that damage accumulation commences early on in the loading history and that it is continuously increasing with load in the form of crack initiation and crack propagation. The results highlight the importance of replicating the loading and restraint conditions of clinical cement mantles when endeavouring to accurately model the damage accumulation process.     

Genetic evaluation of hip score in UK Labrador Retrievers

Hip dysplasia is an important and complex genetic disease in dogs with both genetic and environmental influences. Since the osteoarthritis that develops is irreversible the only way to improve welfare, through reducing the prevalence, is through genetic selection. This study aimed to evaluate the progress of selection against hip dysplasia, to quantify potential improvements in the response to selection via use of genetic information and increases in selection intensity, and to prepare for public provision of estimated breeding values (EBV) for hip dysplasia in the UK. Data consisted of 25,243 single records of hip scores of Labrador Retrievers between one and four years old, from radiographs evaluated between 2000 and 2007 as part of the British Veterinary Association (BVA) hip score scheme. A natural logarithm transformation was applied to improve normality and linear mixed models were evaluated using ASREML. Genetic correlations between left and right scores, and total hip scores at one, two and three years of age were found to be close to one, endorsing analysis of total hip score in dogs aged one to three as an appropriate approach. A heritability of 0.35±0.016 and small but significant litter effect (0.07±0.009) were estimated. The observed trends in both mean hip score and mean EBV over year of birth indicate that a small genetic improvement has been taking place, approximately equivalent to avoiding those dogs with the worst 15% of scores. Deterministic analysis supported by simulations showed that a 19% greater response could be achieved using EBV compared to phenotype through increases in accuracy alone. This study establishes that consistent but slow genetic improvement in the hip score of UK Labrador Retrievers has been achieved over the previous decade, and demonstrates that progress may be easily enhanced through the use of EBVs and more intense selection.     

Finite element and experimental models of cemented hip joint reconstructions can produce similar bone and cement strains in pre-clinical tests

Finite element (FE) models could be used for pre-clinical testing of cemented hip replacement implants against the damage accumulation failure scenario. To accurately predict mechanical failure, the models should accurately predict stresses and strains. This should be the case for various implants. In the current study, two FE models of composite hip reconstructions with two different implants were validated relative to experimental bone and cement strains. The objective was an overall agreement within 10% between experimental and FE strains. Two stem types with different clinical results were analyzed: the Lubinus SPII and the Mueller Curved with loosening rates of 4% and 16% after 10 yr, respectively (Prognosis of total hip replacement. 63rd Annual Meeting of the American Academy of orthopaedic surgeons, Atlanta, USA). For both implant types, six stems were implanted in composite femurs. All specimens were subjected to bending. The Mueller Curved specimens were additionally subjected to torsion. Bone strains were recorded at 10 locations on the cortex and cement strains at three locations within the cement mantle. An FE model was built for both stem types and the experiments were simulated. Bone and cement strains were calculated at the experimental gauge locations. Most FE bone strains corresponded to the mean experimental strains within two standard deviations; most FE cement strains within one standard deviation. Linear regression between the FE and mean experimental strains produced slopes between 0.82 and 1.03, and R(2) values above 0.98. Particularly for the Mueller Curved, agreement improved considerably when FE strains were compared to the strains from the experimental specimen used to build the FE model. The objective of overall agreement within 10% was achieved, indicating that both FE models were successfully validated. This prerequisite for accurately predicting long-term failure has been satisfied.     

人工髋关节置换术在320例股骨头缺血性坏死中的治疗体会

目的：探讨人工髋关节置换术在治疗股骨头缺血性坏死（ANFH）中的临床疗效。方法：选择2007年2月-2011年2月我院收治的320例（340髋）股骨头缺血性坏死患者,均采用人工髋关节置换术对患者进行治疗,其中160例（172髋）患者应用骨水泥型假体进行治疗,另外160例（168）患者采用非骨水泥型假体进行治疗。采用Harris评分对患者手术前后的髋关节功能情况进行评价,并比较骨水泥治疗组和非骨水泥治疗组的临床疗效。结果：患者均获得随访,随访时间为3～18个月。全部患者手术后的Harris评分明显高于手术前,差异有统计学意义（P〈0．05）。骨水泥治疗组和非骨水泥治疗组在术后出血量、术后Harris评分及住院时间方面的差异无统计学意义（P〉0．05）,但非骨水泥治疗组的并发症发生率明显低于骨水泥治疗组（P〈0．05）。结论：采用人工髋关节置换术治疗ANFH疗效显著,能明显改善患者的生活质量,骨水泥型假体与非骨水泥型假体的治疗效果相当,应根据患者的具体情况进行合理的选择。     

In vitro interface and cement mantle analysis of different femur stem designs

The aim of this study is to define stem design related factors causing both gaps in the metal-bone cement interface and cracks within the cement mantle. Six different stem designs (Exeter; Lubinus SP II; Ceraver Osteal; Mueller-straight stem; Centega; Spectron EF) (n=15 of each design) were cemented into artificial femur bones. Ten stems of each design were loaded, while five stems served as an unloaded control. Physiologically adapted cyclical loading (DIN ISO 7206-4) was performed with a hip simulator. After loading both interfaces and the bone cement itself were analysed regarding gaps and cracks in the cement mantle. Significant differences between the stem designs concerning gaps in the metal-bone cement interface and cracks in the cement mantle became apparent. Additionally, a high correlation between gaps in the metal-bone cement interface and cracks within the cement mantle could be proven. Gaps in the metal-bone cement interface but no cracks within the cement mantle were seen in the unloaded specimens. Differences between the unloaded control groups and the cyclical loaded stems regarding the longitudinal extension and width of gaps in the metal-bone cement interface were obvious. The designs of cemented femoral stems have an influence on both the quality of the metal-bone cement contact and the failure rate of the cement mantle. Less interface gaps and less cement defects were found with anatomically formed, collared, well-rounded stem designs without undercuttings.     

Evaluation of bone cement failure criteria with applications to the acetabular region

A Strain energy density (SED) criterion based on a fracture mechanics approach was used to assess the possible failure of acetabular bone cement after total hip replacement. Stress distributions in the cement at the bone-cement interface were calculated using two-dimensional finite element analyses. The results indicate that increasing the thickness of bone cement reduces the risk of cement fracture. The addition of a metal backing to the polyethylene cup and retention of the subchondral bone further reduces the risk of failure. The SED criterion was found to predict the same critical regions as zones of possible cement failure as the von Mises' criterion. Although either criterion can be used for predicting failure in this acetabular analysis both criteria are excessively conservative in predicting failure in regions where high principal compressive stresses are present. Further development of cement failure criteria are indicated.     

人工髋关节置换术在320 例股骨头缺血性坏死中的治疗体会

目的：探讨人工髋关节置换术在治疗股骨头缺血性坏死（ANFH）中的临床疗效。方法：选择2007 年2 月-2011 年2 月我院收 治的320 例（340 髋）股骨头缺血性坏死患者,均采用人工髋关节置换术对患者进行治疗,其中160 例（172 髋）患者应用骨水泥型 假体进行治疗,另外160 例（168）患者采用非骨水泥型假体进行治疗。采用Harris评分对患者手术前后的髋关节功能情况进行评 价,并比较骨水泥治疗组和非骨水泥治疗组的临床疗效。结果：患者均获得随访,随访时间为3～18 个月。全部患者手术后的 Harris评分明显高于手术前,差异有统计学意义（P<0.05）。骨水泥治疗组和非骨水泥治疗组在术后出血量、术后Harris 评分及住 院时间方面的差异无统计学意义（P>0.05）,但非骨水泥治疗组的并发症发生率明显低于骨水泥治疗组（P<0.05）。结论：采用人工 髋关节置换术治疗ANFH疗效显著,能明显改善患者的生活质量,骨水泥型假体与非骨水泥型假体的治疗效果相当,应根据患者 的具体情况进行合理的选择。     

In vitro fatigue failure of cemented acetabular replacements: a hip simulator study

Although hip simulators for in vitro wear testing of prosthetic materials used in total hip arthroplasty (THA) have been available for a number of years, similar equipment has yet to appear for endurance testing of fixation in cemented THA, despite considerable evidence of late aseptic loosening as one of the most significant failure mechanisms in this type of replacements. An in vitro study of fatigue behavior in cemented acetabular replacements has been carried out, utilizing a newly developed hip simulator. The machine was designed to simulate the direction and the magnitude of the hip contact force under typical physiological loading conditions, including normal walking and stair climbing, as reported by Bergmann et al. (2001, Hip 98, Freie Universitaet, Berlin). A 3D finite element analysis has been carried out to validate the function of the hip simulator and to evaluate the effects of boundary conditions and geometry of the specimen on the stress distribution in the cement mantle. Bovine pelvic bones were implanted with a Charnley cup, using standard manual cementing techniques. Experiments were carried out under normal walking and descending stairs loading conditions with selected load levels from a body weight of 75-125 kg. Periodically, the samples were removed from the test rigs to allow CT scanning for the purpose of monitoring damage development in the cement fixation. The hip simulator was found to be satisfactory in reproducing the hip contact force during normal walking and stair climbing, as reported by Bergmann et al. Finite element analysis shows that the stress distributions in the cement mantle and at the bone-cement interface are largely unaffected by the geometry and the boundary conditions of the model. Three samples were tested up to 17 x 10(6) cycles and sectioned post-testing for microscopic studies. Debonding at the bone-cement interface of various degrees in the posterior-superior quadrant was revealed in these samples, and the location of the failures corresponds to the highest stressed region from the finite-element analysis. Preliminary experimental results from a newly developed hip simulator seem to suggest that debonding at the bone-cement interface is the main failure mechanism in cemented acetabular replacements, and descending stairs seem to be more detrimental than normal walking or ascending stairs with regard to fatigue integrity of cement fixation.     

Probabilistic analysis of the influence of the bonding degree of the stem-cement interface in the performance of cemented hip prostheses

The long-term behavior of the stem-cement interface is one of the most frequent topics of discussion in the design of cemented total hip replacements, especially with regards to the process of damage accumulation in the cement layer. This effect is analyzed here comparing two different situations of the interface: completely bonded and debonded with friction. This comparative analysis is performed using a probabilistic computational approach that considers the variability and uncertainty of determinant factors that directly compromise the damage accumulation in the cement mantle. This stochastic technique is based on the combination of probabilistic finite elements (PFEM) and a cumulative damage approach known as B-model. Three random variables were considered: muscle and joint contact forces at the hip (both for walking and stair climbing), cement damage and fatigue properties of the cement. The results predicted that the regions with higher failure probability in the bulk cement are completely different depending on the stem-cement interface characteristics. In a bonded interface, critical sites appeared at the distal and medial parts of the cement, while for debonded interfaces, the critical regions were found distally and proximally. In bonded interfaces, the failure probability was higher than in debonded ones. The same conclusion may be established for stair climbing in comparison with walking activity.     

Kinetic gait analysis in English Bulldogs

Background

Canine breed conformation may interfere with locomotion and may predispose to orthopedic disease. Bulldogs have a high incidence of orthopedic diseases such as hip dysplasia. Kinetic gait analysis provides an objective way to assess and analyze locomotion. The aim of this study was to study the vertical forces of English Bulldogs during walk using a pressure sensitive walkway. We hypothesize that Bulldogs affected by orthopedic diseases have decreased weight bearing and asymmetric locomotion in the limbs despite having mild to no sings during clinical examination. Thirty English Bulldogs were tested. Peak vertical force, vertical impulse, rate of loading, stance phase duration, symmetry index, goniometry and incidence of orthopedic diseases were recorded.

Results

Although none of the dogs showed signs of pain or discomfort upon manipulation of the hip joints, all dogs had radiographic evidences of hip dysplasia and lack of significant peak vertical force, vertical impulse and stance time differences. The dogs had a mean hind limb symmetry index of 19.8 ± 19.5% and rates of loading ranged from 1.0 to 3.1.

Conclusions

Despite the lack of evident decrease in weight bearing, subclinical lameness can be inferred. The examined dogs had a mean hind limb symmetry index of 19.8 ± 19.5%. Symmetry indices reported in dogs free from orthopedic diseases range from 0.3 to 9.6%. Given non-lame dogs are expected to have a symmetry index close to 0%, data from this study suggests that Bulldogs have gait dysfunctions, which translates into hind limb asymmetries and rate of loading was consistent with severe hip dysplasia despite no visible signs of gait dysfunction. Future studies comparing lame and non-lame Bulldogs are warranted.