首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
Diagnosing dysfunctional atlantoaxial motion is challenging given limitations of current diagnostic imaging techniques. Three-dimensional imaging during upright functional motion may be useful in identifying dynamic instability not apparent on static imaging. Abnormal atlantoaxial motion has been linked to numerous pathologies including whiplash, cervicogenic headaches, C2 fractures, and rheumatoid arthritis. However, normal C1/C2 rotational kinematics under dynamic physiologic loading have not been previously reported owing to imaging difficulties. The objective of this study was to determine dynamic three-dimensional in vivo C1/C2 kinematics during upright axial rotation. Twenty young healthy adults performed full head rotation while seated within a biplane X-ray system while radiographs were collected at 30 images per second. Six degree-of-freedom kinematics were determined for C1 and C2 via a validated volumetric model-based tracking process. The maximum global head rotation (to one side) was 73.6 ± 8.3°, whereas maximum C1 rotation relative to C2 was 36.8 ± 6.7°. The relationship between C1/C2 rotation and head rotation was linear through midrange motion (±20° head rotation from neutral) in a nearly 1:1 ratio. Coupled rotation between C1 and C2 included 4.5 ± 3.1° of flexion and 6.4 ± 8.2° of extension, and 9.8 ± 3.8° of contralateral bending. Translational motion of C1 relative to C2 was 7.8 ± 1.5 mm ipsilaterally, 2.2 ± 1.2 mm inferiorly, and 3.3 ± 1.0 mm posteriorly. We believe this is the first study describing 3D dynamic atlantoaxial kinematics under true physiologic conditions in healthy subjects. C1/C2 rotation accounts for approximately half of total head axial rotation. Additionally, C1 undergoes coupled flexion/extension and contralateral bending, in addition to inferior, lateral and posterior translation.  相似文献   

2.
《Journal of thermal biology》2001,26(4-5):365-370
(1) This study describes the performance and the acute physiological responses of heat acclimatised cyclists during three sets of 5×20 s sprints followed by a final sprint to exhaustion in temperate (mean±standard deviation 20.2±0.4°C; 46±2% humidity, 108.5±1.4 kPa water vapour pressure) and in warm conditions (30.5±0.4°C; 47±10% humidity, 206.8±6.4 kPa water vapour pressure). (2) Oxygen consumption was greater in the warm condition and there was no evidence of an increased reliance on anaerobic metabolism as has been reported for submaximal exercise in the heat. (3) Subjects lost 2.1±0.2% of body mass in 53.8±0.2 min during the warm condition. While the duration of the time to exhaustion final sprint was 50±13 s during the warm condition it was 60±7 s for the temperate condition (p=0.020).  相似文献   

3.
In the event of abdominal aortic aneurysm (AAA) rupture, the outcome is often death. This paper aims to experimentally identify the rupture locations of in vitro AAA models and validate these rupture sites using finite element analysis (FEA). Silicone rubber AAA models were manufactured using two different materials (Sylgard 160 and Sylgard 170, Dow Corning) and imaged using computed tomography (CT). Experimental models were inflated until rupture with high speed photography used to capture the site of rupture. 3D reconstructions from CT scans and subsequent FEA of these models enabled the wall stress and wall thickness to be determined for each of the geometries. Experimental models ruptured at regions of inflection, not at regions of maximum diameter. Rupture pressures (mean±SD) for the Sylgard 160 and Sylgard 170 models were 650.6±195.1 mmHg and 410.7±159.9 mmHg, respectively. Computational models accurately predicted the locations of rupture. Peak wall stress for the Sylgard 160 and Sylgard 170 models was 2.15±0.26 MPa at an internal pressure of 650 mmHg and 1.69±0.38 MPa at an internal pressure of 410 mmHg, respectively. Mean wall thickness of all models was 2.19±0.40 mm, with a mean wall thickness at the location of rupture of 1.85±0.33 and 1.71±0.29 mm for the Sylgard 160 and Sylgard 170 materials, respectively. Rupture occurred at the location of peak stress in 80% (16/20) of cases and at high stress regions but not peak stress in 10% (2/20) of cases. 10% (2/20) of models had defects in the AAA wall which moved the rupture location away from regions of elevated stress. The results presented may further contribute to the understanding of AAA biomechanics and ultimately AAA rupture prediction.  相似文献   

4.
IntroductionCutting is an important skill in team-sports, but unfortunately is also related to non-contact ACL injuries. The purpose was to examine knee kinetics and kinematics at different cutting angles.Material and methods13 males and 16 females performed cuts at different angles (45°, 90°, 135° and 180°) at maximum speed. 3D kinematics and kinetics were collected. To determine differences across cutting angles (45°, 90°, 135° and 180°) and sex (female, male), a 4 × 2 repeated measures ANOVA was conducted followed by post hoc comparisons (Bonferroni) with alpha level set at α  0.05 a priori.ResultsAt all cutting angles, males showed greater knee flexion angles than females (p < 0.01). Also, where males performed all cutting angles with no differences in the amount of knee flexion −42.53° ± 8.95°, females decreased their knee flexion angle from −40.6° ± 7.2° when cutting at 45° to −36.81° ± 9.10° when cutting at 90°, 135° and 180° (p < 0.01). Knee flexion moment decreased for both sexes when cutting towards sharper angles (p < 0.05). At 90°, 135° and 180°, males showed greater knee valgus moments than females. For both sexes, knee valgus moment increased towards the sharper cutting angles and then stabilized compared to the 45° cutting angle (p < 0.01). Both females and males showed smaller vGRF when cutting to sharper angles (p < 0.01).ConclusionIt can be concluded that different cutting angles demand different knee kinematics and kinetics. Sharper cutting angles place the knee more at risk. However, females and males handle this differently, which has implications for injury prevention.  相似文献   

5.
Acoustic heart signals, generated by the mechanical processes of the cardiac cycle, carry significant information about the underlying functioning of the cardiovascular system. We describe a computational analysis framework for identifying distinct morphologies of heart sounds and classifying them into physiological states. The analysis framework is based on hierarchical clustering, compact data representation in the feature space of cluster distances and a classification algorithm. We applied the proposed framework on two heart sound datasets, acquired during controlled alternations of the physiological conditions, and analyzed the morphological changes induced to the first heart sound (S1), and the ability to predict physiological variables from the morphology of S1. On the first dataset of 12 subjects, acquired while modulating the respiratory pressure, the algorithm achieved an average accuracy of 82 ± 7% in classifying the level of breathing resistance, and was able to estimate the instantaneous breathing pressure with an average error of 19 ± 6%. A strong correlation of 0.92 was obtained between the estimated and the actual breathing efforts. On the second dataset of 11 subjects, acquired during pharmacological stress tests, the average accuracy in classifying the stress stage was 86 ± 7%. The effects of the chosen raw signal representation, distance metrics and classification algorithm on the performance were studied on both real and simulated data. The results suggest that quantitative heart sound analysis may provide a new non-invasive technique for continuous cardiac monitoring and improved detection of mechanical dysfunctions caused by cardiovascular and cardiopulmonary diseases.  相似文献   

6.
This study aims to quantify the biomechanical properties of murine temporomandibular joint (TMJ) articular disc and condyle cartilage using AFM-nanoindentation. For skeletally mature, 3-month old mice, the surface of condyle cartilage was found to be significantly stiffer (306 ± 84 kPa, mean ± 95% CI) than those of the superior (85 ± 23 kPa) and inferior (45 ± 12 kPa) sides of the articular disc. On the disc surface, significant heterogeneity was also detected across multiple anatomical sites, with the posterior end being the stiffest and central region being the softest. Using SEM, this study also found that the surfaces of disc are composed of anteroposteriorly oriented collagen fibers, which are sporadically covered by thinner random fibrils. Such fibrous nature results in both an F-D3/2 indentation response, which is a typical Hertzian response for soft continuum tissue under a spherical tip, and a linear F-D response, which is typical for fibrous tissues, further signifying the high degree of tissue heterogeneity. In comparison, the surface of condyle cartilage is dominated by thinner, randomly oriented collagen fibrils, leading to Hertzian-dominated indentation responses. As the first biomechanical study of murine TMJ, this work will provide a basis for future investigations of TMJ tissue development and osteoarthritis in various murine TMJ models.  相似文献   

7.
To better protect soldiers from blast threat, that principally affect air-filled organs such a lung, it is necessary to develop an adapted injury criterion and, prior to this, to evaluate the response of a biological model against that threat. The objective of this study is to provide some robust data to quantify the chest response of post-mortem swine under blast loadings.7 post-mortem swine (54.5 ± 2.6 kg), placed side-on to the threat and against the ground, were exposed to 5 shock-waves of increasing intensities. Their thorax were instrumented with a piezo-resistive pressure sensor, an accelerometer directly exposed to the shock-wave and a target was mounted on the latter in order to track the chest wall displacement.For incident impulses ranging from 47 kPa ms ± 2% to 173 kPa ms ± 6%, the measured maximum of linear chest wall acceleration (Γmax) goes from 5800 m/s2 ± 16% to 41,000 m/s2 ± 8%, with a duration of 0.8 ms. Chest wall displacements ranging from 5 mm ± 20% to 20 mm ± 15%, with a duration of 9 ms, are reached. These reproducible data were used to find simple relations (linear, 2nd and 3rd order polynomials) between the kinematic parameters (plus the viscous criterion) and the incident and reflected impulses.Correlating the new reproducible data with the prediction from the Bowen curves showed a lung injury threshold in terms of Γmax similar to that of Cooper (10,000 m/s2). However, the limits defined for the viscous criterion in the automobile field and for non-lethal weapons seems not adapted for the blast threat.  相似文献   

8.
The Pacinian corpuscle (PC) is a cutaneous mechanoreceptor sensitive to high-frequency vibrations (20–1000 Hz). The PC is of importance due to its integral role in somatosensation and the critical need to understand PC function for haptic feedback system development. Previous theoretical and computational studies have modeled the physiological response of the PC to sustained or vibrating mechanical stimuli, but they have used estimates of the receptor’s mechanical properties, which remain largely unmeasured. In this study, we used micropipette aspiration (MPA) to determine an apparent Young’s modulus for PCs isolated from a cadaveric human hand. MPA was applied in increments of 5 mm H2O (49 Pa), and the change in protrusion length of the PC into the pipette was recorded. The protrusion length vs. suction pressure data were used to calculate the apparent Young’s modulus. Using 10 PCs with long-axis lengths of 2.99 ± 0.41 mm and short-axis lengths of 1.45 ± 0.22 mm, we calculated a Young’s modulus of 1.40 ± 0.86 kPa. Our measurement is on the same order of magnitude as those approximated in previous models, which estimated the PC to be on the same order of magnitude as skin or isolated cells, so we recommend that a modulus in the kPa range be used in future studies.  相似文献   

9.
Intraoperative digitization of osseous structures is an integral component of computer-assisted orthopaedic surgery. This study determined the repeatability and accuracy of predicting known radii and center locations of spherical objects for different proportions of digitized surface areas and various sphere sizes. Also, we investigated these accuracies for some relevant near-spherical osseous structures where results from full area digitizations were considered to be true. Digitizations were performed using an electromagnetic tracker with a stylus on the total and fractional surfaces of 10 hemispheres, ranging from 10 to 28 mm in radius. Repeatability was quantified by digitizing five trials of the entire surface and various fractional areas of selected hemisphere sizes. Similar trials were conducted on models of a humeral and femoral head, using the full head area as baseline and digitizing 15 and 30 mm diameter areas of the full head. Mean error for the predicted radii and center positions of the hemispheres ranged from 0.39±0.29 to 0.14±0.07 mm and 0.52±0.31 to 0.22±0.12 mm, respectively. Repeatability for the predicted radii and centers produced maximum standard deviations of 0.31 and 0.42 mm, respectively. All errors decreased as fractional area (40%, 60%, 80% and 100%) increased (p<0.05). Radius of curvature and center position errors for the humeral head model were 1.51±2.11 and 2.28±1.51 mm, respectively. These errors for the femoral head model were 3.37±4.14 and 4.25±4.14 mm, respectively. Errors resulting from the prediction of radius and center indicate that non-spherical anatomical structures are more sensitive to the digitized area, and hence digitization of the largest surface possible seems warranted.  相似文献   

10.
This paper investigates the relationship between plasma trace element and plasma leptin, as well as percent fat mass, in 16 male basketball athletes. Blood samples were obtained before intensive training and 24 h after intensive training to measure plasma zinc (Zn), copper (Cu), calcium (Ca), magnesium (Mg), iron (Fe), and leptin levels. High-density lipoprotein cholesterol (HDL), low-density lipoprotein cholesterol (LDL), triglyceride (TG), total and cholesterol (TC) levels were determined using commercially available kits for humans. Subjects presented similar values in terms of age (21.1 ± 2.2 years old), body mass index (23.9 ± 2.00 kg/m2), percent body fat (14.40 ± 1.52%), plasma hemoglobin (150.1 ± 9.4 g/L), plasma Zn (17.47 ± 1.28 μmol/l), plasma Cu (13.42 ± 1.40 μmol/L), plasma Ca (2.41 ± 0.14 mmol/L), and plasma Mg (0.96 ± 0.02 mmol/L). The correlation analysis between degree of plasma leptin and plasma element contents was performed using the SPSS 16.0 software. Plasma Zn correlated positively with plasma leptin (r = 0.746, P < 0.01), Cu–Zn SOD (r = 0.827, P < 0.01), and negatively with percent fat mass (r = –0.598, P < 0.05) under no-training conditions. Meanwhile, plasma Cu, Ca, Mg, and Fe did not correlate with plasma leptin or percent fat mass (P > 0.05). In conclusion, plasma Zn may be involved in the regulation of plasma leptin and may serve as a lipid-mobilizing factor in Chinese men's basketball athletes.  相似文献   

11.
We developed an intravaginal instrumented probe (covered with a 10 × 10 matrix of capacitive sensors) for assessing the three-dimensional (3D) spatiotemporal pressure profile of the vaginal canal. The pressure profile was compared to the pelvic floor (PF) digital assessment, and the reliability of the instrument and repeatability of the protocol was tested. We also tested its ability to characterize and differentiate two tasks: PF maximum contraction and Valsalva maneuver (maximum intra-abdominal effort with downward movement of the PF). Peak pressures were calculated for the total matrix, for three major sub-regions, and for 5 planes and 10 rings throughout the vaginal canal. Intraclass correlation coefficients indicated excellent inter- and intra-rater reliability and intra-trial repeatability for the total and medial areas, with moderate reliability for the cranial and caudal areas. There was a moderate correlation between peak pressure and PF digital palpation [Spearman’s coefficient r = 0.55 (p < 0.001)]. Spatiotemporal profiles were completely different between tasks (2-way ANOVAs for repeated measures) with notably higher pressures (above 30 kPa) for the maximum contraction task compared to Valsalva (below 15 kPa). At maximum contraction, higher pressures occurred in the mid-antero-posterior zone, with earlier peak pressure onsets and more variable along the vaginal depth (from rings 3 to 10-caudal). During Valsalva, the highest pressures were observed in rings 4–6, with peak pressure onsets more synchronized between rings. With this protocol and novel instrument, we obtained a high-resolution and highly reliable innovative 3D pressure distribution map of the PF capable of distinguishing vaginal sub-regions, planes, rings and tasks.  相似文献   

12.
The carob moth, Ectomyelois ceratoniae (Lepidoptera: Pyralidae), is the most important pest of pomegranate orchards (in terms of economic damage) within Iran, and hence, several control procedures, including biological methods of control, have been attempted as a means of controlling populations of this insect. This research was carried out in order to study the biology of Apanteles myeloenta (Hymenoptera: Braconidae), a larval parasitoid of the carob moth. Laboratory studies were conducted to determine larval developmental time, adult longevity, sex ratio, parasite progeny production, and host stage preference of A. myeloenta. At 25 ± 1 °C, immature developmental time (egg to pupa; mean ± SE) was 28.33 ± 0.85 days and 27.46 ± 0.37 days for male and females, respectively. Adult females survived on average 17.5 ± 0.14, 11.7 ± 0.22, 3.4 ± 0.18, and 2.8 ± 0.12 days at 25 C when provided with honey and water, honey only, water only or no food source, respectively. The sex ratio (females to males) of A. myeloenta was 1:3.5 from hosts parasitized in the first instar, 1:3 for second instars and 1:2 for third instar carob moth larvae. Female A. myeloenta typically preferred to parasitize second instar over third or first instar. The oviposition activity peaked on the 7th and 8th days following emergence, when provided with honey, and 10% sucrose solution, respectively.  相似文献   

13.
Planting density influence on fibrous root reinforcement of soils   总被引:2,自引:0,他引:2  
Reinforcement of soil by fibrous roots is crucial for preventing soil erosion and degradation, yet the underlying mechanisms are poorly understood. We investigated soil reinforcement by roots of barley (Hordeum vulgare) planted at different densities in a controlled glasshouse and a separate field study. Soil shear strength increased with planting density (0–950 m?2) at 5 weeks with an average 6.7 ± 1.40 kPa increase in strength over the fallow (7.5 ± 0.47 kPa). At 20 weeks, planting density had less of an effect, with on average a 29% increase in strength contributed by roots. In the glasshouse study, roots increased shear strength by an average of 53%, with a positive effect found for the eight planting densities tested ranging from 0 to 1130 plants/m2. Detailed measures of root tensile strength, and diameter distributions at the shear plane, allowed us to apply and test two existing root reinforcement models of Wu et al. [Wu, T.H., Mckinnell, W.P., Swanston, D.N., 1979. Strength of tree roots and landslides on Prince-Of-Wales-Island, Alaska. Canadian Geotechnical Journal 16, 19–33] and Pollen and Simon [Pollen, N., Simon, A., 2005. Estimating the mechanical effects of riparian vegetation on stream bank stability using a fiber bundle model. Water Resources Research, 41]. A progressive failure Fibre Bundle Model, developed by Pollen and Simon [Pollen, N., Simon, A., 2005. Estimating the mechanical effects of riparian vegetation on stream bank stability using a fiber bundle model. Water Resources Research, 41], predicted reinforcement better than the catastrophic failure model by Wu et al. [Wu, T.H., Mckinnell, W.P., Swanston, D.N., 1979. Strength of tree roots and landslides on Prince-Of-Wales-Island, Alaska. Canadian Geotechnical Journal 16, 19–33], but neither described reinforcement well for field-grown plants near maturity at 20 weeks.  相似文献   

14.
The main purpose of this study was to compare three methods of determining relative effort during sit-to-stand (STS). Fourteen young (mean 19.6 ± SD 1.2 years old) and 17 older (61.7 ± 5.5 years old) adults completed six STS trials at three speeds: slow, normal, and fast. Sagittal plane joint torques at the hip, knee, and ankle were calculated through inverse dynamics. Isometric and isokinetic maximum voluntary contractions (MVC) for the hip, knee, and ankle were collected and used for model parameters to predict the participant-specific maximum voluntary joint torque. Three different measures of relative effort were determined by normalizing STS joint torques to three different estimates of maximum voluntary torque. Relative effort at the hip, knee, and ankle were higher when accounting for variations in maximum voluntary torque with joint angle and angular velocity (hip = 26.3 ± 13.5%, knee = 78.4 ± 32.2%, ankle = 27.9 ± 14.1%) compared to methods which do not account for these variations (hip = 23.5 ± 11.7%, knee = 51.7 ± 15.0%, ankle = 20.7 ± 10.4%). At higher velocities, the difference in calculating relative effort with respect to isometric MVC or incorporating joint angle and angular velocity became more evident. Estimates of relative effort that account for the variations in maximum voluntary torque with joint angle and angular velocity may provide higher levels of accuracy compared to methods based on measurements of maximal isometric torques.  相似文献   

15.
The purpose of this study was to determine the changes that occur in tendinous tissue properties during the early phase of tetanic summation in the in vivo human tibialis anterior muscle (TA). The torque response and tendinous tissue elongation following single stimuli, two-pulse trains, and three-pulse trains were recorded in the TA during isometric contractions. The elongation, compliance, and lengthening velocity of tendinous tissue were determined by real-time ultrasonography. The contribution of the response to the second stimulation (C2) was obtained by subtracting the response to the single stimulation (C1) from the response of doublet. The third contribution (C3) was obtained by subtracting the response to the doublet from that of the triplet. C2 (7.8±0.5 Nm) and C3 (7.3±0.6 Nm) had torque responses significantly higher than C1 (3.6±0.7 Nm). In contrast, the elongations of tendinous tissue for C2 (2.8±0.4 mm) and C3 (1.7±0.2 mm) were significantly lower than for C1 (4.9±0.3 mm), indicating that the summation pattern of tendinous tissue elongation is different from the summation pattern of torque response. In addition, this showed considerable difference both between C1 (0.12±0.01 mm/N; 83±4.6 mm/s) and C2 (0.03±0.005 mm/N; 50±6.3 mm/s) and between C1 and C3 (0.02±0.002 mm/N; 39±6.4 mm/s) in the compliance and lengthening velocity of tendinous tissue. These results suggest that changes in tendinous tissue properties between first and second contraction are related to different summation patterns of force and tendinous tissue elongation during early phase of tetanic summation.  相似文献   

16.
This study used subject-specific measures of three-dimensional (3D) free Achilles tendon geometry in conjunction with a finite element method to investigate the effect of variation in subject-specific geometry and subject-specific material properties on tendon stress during submaximal isometric loading. Achilles tendons of eight participants (Aged 25–35 years) were scanned with freehand 3D ultrasound at rest and during a 70% maximum voluntary isometric contraction. Ultrasound images were segmented, volume rendered and transformed into subject-specific 3D finite element meshes. The mean (±SD) lengths, volumes and cross-sectional areas of the tendons at rest were 62 ± 13 mm, 3617 ± 984 mm3 and 58 ± 11 mm2 respectively. The measured tendon strain at 70% MVIC was 5.9 ± 1.3%. Subject-specific material properties were obtained using an optimisation approach that minimised the difference between measured and modelled longitudinal free tendon strain. Generic geometry was represented by the average mesh and generic material properties were taken from the literature. Local stresses were subsequently computed for combinations of subject-specific and generic geometry and material properties. For a given geometry, changing from generic to subject-specific material properties had little effect on the stress distribution in the tendon. In contrast, changing from generic to subject-specific geometry had a 26-fold greater effect on tendon stress distribution. Overall, these findings indicate that the stress distribution experienced by the living free Achilles tendon of a young and healthy population during voluntary loading are more sensitive to variation in tendon geometry than variation in tendon material properties.  相似文献   

17.
We aimed to reveal the anti-convulsant effects of oxytocin (OT) in pentylenetetrazol (PTZ)-induced seizures in rats. Thirty rats were randomly divided into 5 equal groups. Using stereotaxy, we implanted electroencephologram (EEG) electrodes in the left nucleus of the posterior thalamus. After 2 days, the first and second groups were used as the control and PTZ (35 mg/kg) groups, respectively. We administered 40, 80 and 160 nmol/kg OT + 35 mg/kg PTZ to the rats, constituting the third, fourth, and fifth groups, respectively, for 5 days. At the end of 5 days, we recorded EEGs via bipolar EEG electrodes. After 12 h, all groups except the first received 70 mg/kg PTZ and we determined the dose–response ratio. Racine's Convulsion Scale was used to evaluate seizures. The spike–wave complex percentage in the EEG was determined as 0% for the first group, 38.6% ± 7.2 for the second group, 36.4% ± 5.6 for the third group, 4.3% ± 1.8 for the fifth group and 4.1% ± 1.1 for the fifth group. The fourth and fifth groups had significantly decreased spike–wave complex percentages compared to the second group (p < 0.0001). OT may prevent PTZ-induced epilepsy on an EEG. OT may also be considered for use in the treatment of epilepsy in the future.  相似文献   

18.
There has been a broad spectrum of theoretical and experimental works on microorganism disruption methods undertaken in the past. However, there is a lack of understanding regarding the actual reasons for microorganism disruption using ultrasound and whether it is caused by shock or shear. In the case of shear stress, which is the focus of this paper, analysis of the intense turbulent flow region of an in-house built shear apparatus combined with the experimental results demonstrated that when the energy dissipation rate in the turbulence region is high, and the size of the eddy is smaller than the size of the cell, the likelihood of yeast disruption is high. The mechanical properties of yeast cells combined with the calculated energy dissipation rate were used to evaluate the yeast disruption efficiency (log reduction). The results show that the shear apparatus can efficiently and effectively disrupt S. cerevisiae at different treatment times, suspension temperatures and rotor speeds. The experimental work suggests that maximum yeast log reduction was achieved when the maximum power dissipation of 2.095 kW was recorded at 10,000 RPM, while suspension temperature was controlled below 35 °C. The corresponding shear stress at 10,000 RPM was 2586.2 Pa.  相似文献   

19.
Blood platelets when activated are involved in the mechanisms of hemostasis and thrombosis, and their migration toward injured vascular endothelium necessitates interaction with red blood cells (RBCs). Rheology co-factors such as a high hematocrit and a high shear rate are known to promote platelet mass transport toward the vessel wall. Hemodynamic conditions promoting RBC aggregation may also favor platelet migration, particularly in the venous system at low shear rates. The aim of this study was to confirm experimentally the impact of RBC aggregation on platelet-sized micro particle migration in a Couette flow apparatus. Biotin coated micro particles were mixed with saline or blood with different aggregation tendencies, at two shear rates of 2 and 10 s−1 and three hematocrits ranging from 20 to 60%. Streptavidin membranes were respectively positioned on the Couette static and rotating cylinders upon which the number of adhered fluorescent particles was quantified. The platelet-sized particle adhesion on both walls was progressively enhanced by increasing the hematocrit (p < 0.001), reducing the shear rate (p < 0.001), and rising the aggregation of RBCs (p < 0.001). Particle count was minimum on the stationary cylinder when suspended in saline at 2 s−1 (57 ± 33), and maximum on the rotating cylinder at 60% hematocrit, 2 s−1 and the maximum dextran-induced RBC aggregation (2840 ± 152). This fundamental study is confirming recent hypotheses on the role of RBC aggregation on venous thrombosis, and may guide molecular imaging protocols requiring injecting active labeled micro particles in the venous flow system to probe human diseases.  相似文献   

20.
In this study we investigated balancing responses to lateral perturbations during slow walking (0.85 m/s). A group of seven healthy individuals walked on an instrumented treadmill while being perturbed at the level of waist at left heel strike in outward and inward lateral directions. Centre of mass (COM) and centre of pressure (COP), rotation of pelvis around vertical axis, step lengths, step widths and step times were assessed. The results have shown that beside control of COP in lateral direction, facilitated by adequate step widths, control of COP in sagittal direction, slowing down movement of COM was present after commencement of lateral perturbations. Sagittal component of COM was significantly retarded as compared to unperturbed walking for both inward (4.32 ± 1.29 cm) and outward (9.75 ± 2.17 cm) perturbations. This was necessary since after an inward perturbation first step length (0.29 ± 0.04 m compared to 0.52 ± 0.02 m in unperturbed walking) and step time (0.45 ± 0.05 s compared to 0.61 ± 0.04 s in unperturbed walking) were shortened while after an outward perturbation first two step lengths (0.36 ± 0.05 m and 0.32 ± 0.11 m compared to 0.52 ± 0.03 m in unperturbed walking) were shortened that needed to be accommodated by the described modulation of COP in sagittal plane. In addition pronounced pelvis rotation assisted in bringing swing leg to new location. The results of this study show that counteracting lateral perturbations at slow walking requires adequate response in all three planes of motion.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号