Ion-Pair Chromatography for Simultaneous Analysis of Ethionamide and Pyrazinamide from Their Porous Microparticles

Ethionamide (ETA) and pyrazinamide (PZA) are considered the drugs of choice for the treatment of multidrug-resistant tuberculosis. Current methods available in the literature for simultaneous determination of ETA and PZA have low sensitivity or involve column modifications with lipophilic cations. The aim of this study was to develop a simple and validated reversed-phase ion-pair HPLC method for simultaneous determination of ETA and PZA for the characterization of polymeric-based porous inhalable microparticles in in vitro and spiked human serum samples. Chromatographic separation was achieved on a Phenomenex C₁₈ column (250 mm × 4.6 mm) using a Shimadzu LC 10 series HPLC. The mobile phase consisted of A: 0.01% trifluoroacetic acid in distilled water and B: ACN/MeOH at 1:1 v/v. Gradient elution was run at a flow rate of 1.5 mL/min and a fixed UV wavelength of 280 nm. The validation characteristics included accuracy, precision, linearity, analytical range, and specificity. Calibration curves at seven levels for ETA and PZA were linear in the analytical range of 0.1–3.0 μg/mL with correlation coefficient of r² > 0.999. Accuracy for both ETA and PZA ranged from 94 to 106% at all quality control (QC) standards. The method was precise with relative standard deviation less than 2% at all QC levels. Limits of quantitation for ETA and PZA were 50 and 70 ng/mL, respectively. There was no interference from either the polymeric matrix ions or the biological matrix in the analysis of ETA and PZA.Key words: ethionamide, HPLC, microparticles, pyrazinamide, tuberculosis     

Optimization of Storage and Manufacture Conditions for Imidapril Hydrochloride in Solid State as a Way to Reduce Costs of Antihypertensive Therapy

The effect of temperature and relative humidity (RH) on the stability of imidapril hydrochloride (IMD) in solid state was investigated. The main aim of this study was to determine the most appropriate conditions of storage and manufacture of IMD so that the efficiency of the technological process could be improved and its costs could be minimized. A reversed-phase high-performance liquid chromatography was validated and applied for the determination of IMD degradation samples under the following operating conditions: stationary phase, LiChrospher 100 RP-18 (size 5 μm) 250 × 4 mm I.D., and mobile phase, acetonitrile–methanol–phosphate buffer, pH 2.0, 0.035 mol L⁻¹ (60:10:30 v/v/v). The effect of temperature on IMD degradation rate was analyzed under increased RH ∼76.4% (within temperature range of 70–90°C) and decreased RH ∼0% (within temperature range of 90–110°C). The influence of RH was investigated under 90°C within RH range of 25.0–76.4%. IMD degradation accords with autocatalytic reaction model, and RH has no influence on its mechanism yet it increases its rate. The reaction also accelerates under high temperatures and in the presence of IMD degradation product. Pure IMD is more stable than other structurally related angiotensin-converting enzyme inhibitors, such as enalapril maleate, but it still should be stored in tightly closed containers and protected from moisture and high temperatures.KEY WORDS: angiotensin-converting enzyme inhibitors, imidapril hydrochloride, RP-HPLC, stability, thermodynamics     

Factors Affecting the Stability and Performance of Ipratropium Bromide; Fenoterol Hydrobromide Pressurized-Metered Dose Inhalers

The aim of the study was to investigate the factors affecting the stability and performance of ipratropium bromide and fenoterol hydrobromide in a pressurized-metered dose inhaler (pMDI). A factorial design was applied to investigate the effects of three parameters (propellant, water, and ethanol) on the performance of 27 designed formulations of a solution-based pMDI. The formulations that contained a hydrofluoroalkane (HFA) propellant lower than 72% v/v and an ethanol concentration higher than 27% v/v remained as clear solutions. Nine formulations that contained the HFA propellant higher than 74% v/v precipitated. The results indicated that it was not only the HFA propellant content of the formulations that was related to the formulation instability but also ethanol content. Only six formulations from the 18 formulations, that did not precipitate, produced drug contents that were within the acceptable range (80–120%). These six formulations generated aerosols with mass median aerodynamic diameters (MMAD) of approximately 2 μm with a fine particle fraction (FPF; particle size, <6.4 μm) between 45% and 52%. The MMAD and FPF did not change significantly after 6 months of storage (P > 0.05).KEY WORDS: fenoterol hydrobromide, ipratropium bromide, pressurized metered dose inhaler, stability     

Niosomal Gel of Lornoxicam for Topical Delivery: In vitro Assessment and Pharmacodynamic Activity

Lornoxicam is a potent oxicam class of non steroidal anti-inflammatory agent, prescribed for mild to moderate pain and inflammation. Niosomal gel of lornoxicam was developed for topical application. Lornoxicam niosomes (Lor-Nio) were fabricated by thin film hydration technique. Bilayer composition of niosomal vesicles was optimized. Lor-Nio dispersion was characterized by DSC, XRD, and FT-IR. Morphological evaluation was performed by scanning electron microscopy (SEM). Lor-Nio dispersion was incorporated into a gel using 2% w/w Carbopol 980 NF. Rheological and texture properties of Lor-Nio gel formulation showed suitability of the gel for topical application. The developed formulation was evaluated for in vitro skin permeation and skin deposition studies, occlusivity test and skin irritation studies. Pharmacodynamic activity of the Lor-Nio gel was performed by carragenan-induced rat paw model. Optimized Lor-Nio comprised of Span 60 and cholesterol in a molar ratio of 3:1 with 30 μM dicetyl palmitate as a stabilizer. It had particle size of 1.125 ± 0.212 μm (d₉₀), with entrapment efficiency of 52.38 ± 2.1%. DSC, XRD, and IR studies showed inclusion of Lor into niosomal vesicles. SEM studies showed spherical closed vesicular structure with particles in nanometer range. The in vitro skin permeation studies showed significant improvement in skin permeation and skin deposition for Lor-Nio gel (31.41 ± 2.24 μg/cm², 30.079 ± 1.2 μg/cm²) over plain lornoxicam gel (7.37 ± 1.27 μg/cm², 6.6 ± 2.52 μg/cm²). The Lor-Nio gel formulation showed enhanced anti-inflammatory activity by exhibiting mean edema inhibition (87.69 ± 1.43%) which was significantly more than the plain lornoxicam gel (53.84 ± 2.21%).KEY WORDS: anti-inflammatory activity, lornoxicam, niosomes, rheology, texture analysis     

Increased In Situ Intestinal Absorption of Phytoestrogenic Diarylheptanoids from Curcuma comosa in Nanoemulsions

Curcuma comosa has long been used as a gynecological medicine. Several diarylheptanoids have been purified from this plant, and their pharmacological effects were proven. However, there is no information about the absorption of C. comosa components to support the formulation usage. In the present study, C. comosa hexane extract and the mixture of its two major compounds, (4E,6E)-1,7-diphenylhepta-4,6-dien-3-ol (DA1) and (6E)-1,7-diphenylhept-6-en-3-ol (DA2), were formulated into nanoemulsions. The physical properties of the nanoemulsions and the in situ intestinal absorptions of DA1 and DA2 were evaluated. The results demonstrated the mean particle sizes at 0.207 ± 0.001 and 0.408 ± 0.014 μm, and the zeta potential at −14.57 ± 0.85 and −10.47 ± 0.32 mV for C. comosa nanoemulsion (C.c-Nano) and mixture of diarlylheptanoid nanoemulsions (DA-Nano), respectively. The entrapments of DA1 and DA2 were 76.61% and 75.41%, and 71.91% and 71.63% for C.c-Nano and DA-Nano, respectively. The drug loading ratios of DA1 and DA2 were 351.47 and 614.53 μg/mg, and 59.48 and 126.72 μg/mg for C.c-Nano and DA-Nano. The intestinal absorption rates of DA1 and DA2 were 0.329 ± 0.015 and 0.519 ± 0.026 μg/min/cm² in C.c-Nano, and 0.380 ± 0.006 and 0.428 ± 0.036 μg/min/cm² in DA-Nano, which were five to ten times faster than those in oil. In conclusion, the formulation in nanoemulsion forms obviously increased the intestinal absorption rate of diarylheptanoids.KEY WORDS: Curcuma comosa, diarylheptanoids, intestinal absorption, nanoemulsion, phytoestrogen     

Development and Clinical Evaluation of Clotrimazole–β-Cyclodextrin Eyedrops for the Treatment of Fungal Keratitis

Fungal keratitis is a serious corneal disease that may result in loss of vision. There are limited treatment options available in Iraqi eye hospitals which might be the main reason behind the poor prognosis of many cases. The purpose of this study was to prepare and pharmaceutically evaluate clotrimazole–β-cyclodextrin (CTZ–β-CD) eyedrops then clinically assess its therapeutic efficacy on fungal keratitis compared with extemporaneous amphotericin B eyedrops (0.5% w/v). A CTZ–β-CD ophthalmic solution was prepared and evaluated by various physicochemical, microbiological, and biological tests. The prepared formula was stable in 0.05 M phosphate buffer pH 7.0 at 40 ± 2°C and 75 ± 5% RH for a period of 6 months. Light has no significant effect on the formula’s stability. The CTZ–β-CD eyedrops efficiently complied with the isotonicity, sterility, and antimicrobiological preservative effectiveness tests. Results of the clinical study revealed that 20 (80%) patients showed a favorable response to the CTZ–β-CD eyedrops, while 16 patients (64%) exhibited a favorable response to amphotericin B (P > 0.05). The mean course of treatment was significantly (P < 0.05) less in the CTZ treatment group than in the amphotericin group (21.5 ± 5.2 vs. 28.3 ± 6.4 days, respectively). The CTZ formulation was significantly (P < 0.05) more effective in the management of severe cases and also against Candida sp. than amphotericin B. There was no significant difference (P < 0.05) between both therapies against filamentous fungi. The CTZ–β-CD formulation can be used alternatively to other ophthalmic antimycotic treatment options in developing countries where stability, cost, or efficacy is a limiting factor.Key words: clotrimazole, β-cyclodextrin, eyedrops, fungal keratitis, Iraq     

Micropropagtion of Terminalia bellerica from nodal explants of mature tree and assessment of genetic fidelity using ISSR and RAPD markers

The present study reports an efficient in vitro micropropagation protocol for a medicinally important tree, Terminalia bellerica Roxb. from nodal segments of a 30 years old tree. Nodal segments taken from the mature tree in March-April and cultured on half strength MS medium gave the best shoot bud proliferation response. Combinations of serial transfer technique (ST) and incorporation of antioxidants (AO) [polyvinylpyrrolidone, PVP (50 mg l⁻¹) + ascorbic acid (100 mg l⁻¹) + citric acid (10 mg l⁻¹)] in the culture medium aided to minimize browning and improve explant survival during shoot bud induction. Highest multiplication of shoots was achieved on medium supplemented with 6-benzyladenine (BA, 8.8 μM) and α-naphthalene acetic acid (NAA, 2.6 μM) in addition to antioxidants. Shoot elongation was obtained on MS medium containing BA (4.4 μM) + phloroglucinol (PG, 3.9 μM). Elongated shoots were transferred to half strength MS medium containing indole-3-butyric acid (IBA, 2.5 μM) for root development. The acclimatization of plantlets was carried out under greenhouse conditions. The genetic fidelity of the regenerated plants was checked using inter simple sequence repeats (ISSR) and randomly amplified polymorphic DNA (RAPD) analysis. Comparison of the bands among the regenerants and mother plant confirmed true-to-type clonal plants.     

Enhanced Topical Delivery of Finasteride Using Glyceryl Monooleate-Based Liquid Crystalline Nanoparticles Stabilized by Cremophor Surfactants

The aim of this study was to investigate the capability of two surfactants, Cremophor RH 40 (RH) and Cremophor EL (EL), to prepare liquid crystalline nanoparticles (LCN) and to study its influence on the topical delivery of finasteride (FNS). FNS-loaded LCN was formulated with the two surfactants and characterized for size distribution, morphology, entrapment efficiency, in vitro drug release, and skin permeation/retention. Influence of FNS-loaded LCN on the conformational changes on porcine skin was also studied using attenuated total reflectance Fourier-transform infrared spectroscopy. Transmission electron microscopical image confirmed the formation of LCN. The average particle size of formulations was in the range of 165.1–208.6 and 153.7–243.0 nm, respectively. The formulations prepared with higher surfactant concentrations showed faster release and significantly increased skin permeation. Specifically, LCN prepared with RH 2.5% presented higher permeation flux (0.100 ± 0.005 μgcm⁻²h⁻¹) compared with lower concentration (0.029 ± 0.007 μgcm⁻²h⁻¹). Typical spectral bands of lipid matrix of porcine skin were shifted to higher wavenumber, indicating increased degree of disorder of the lipid acyl chains which might cause fluidity increase of stratum corneum. Taken together, Cremophor surfactants exhibited a promising potential to stabilize the LCN and significantly augmented the skin permeation of FNS.KEY WORDS: Cremophor, finasteride, liquid crystalline nanoparticles, skin permeation–retention     

Plasma levels of alpha-1-antichymotrypsin are elevated in patients with chronic heart failure,but are of limited prognostic value

Background

There is increasing interest in utilising novel markers of cardiovascular disease risk in patients with chronic heart failure (HF). Recently, it was shown that alpha-1-antichymotrypsin (ACT), an acute-phase protein and major inhibitor of cathpesin G, plays a role in the pathophysiology of HF and may serve as a marker for myocardial distress.

Objective

To assess whether ACT is independently associated with long-term mortality in chronic HF patients.

Methods

ACT plasma levels were categorised into quartiles. Survival times were analysed using Kaplan-Meier curves and Cox proportional hazards regression, without and with correction for clinically relevant risk factors, including sex, age, duration of HF, kidney function (MDRD), ischaemic HF aetiology and NT-proBNP.

Results

Twenty healthy individuals and 224 patients (mean age 71 years, 72 % male, median HF duration 1.6 years) with chronic HF were included. In total, 159 (71 %) patients died. The median survival time was 5.3 (95 % CI 4.5–6.1) years. ACT was significantly elevated in patients (median 433 μg/ml, IQR 279–680) in comparison with controls (median 214 μg/ml, IQR 166–271; p < 0.001). Cox regression analysis demonstrated that ACT was not independently related to long-term mortality in chronic HF patients (crude HR = 1.03, 95 % CI 0.75–1.41, p = 0.871; adjusted HR = 1.12, 95 % CI 0.78–1.60, p = 0.552), which was confirmed by Kaplan-Meier curves.

Conclusion

ACT levels are elevated in chronic HF patients, but no independent association with long-term mortality can be established.     

An efficient in vitro shoot regeneration from immature inflorescence and ex vitro rooting of Arnebia hispidissima (Lehm). DC. - A red dye (Alkannin) yielding plant

Arnebia hispidissima, which belongs to the family Boraginaceae, is an important medicinal and dye yielding plant. The alkannin, a red dye, are root-specific secondary metabolites of A. hispidissima. Shoots were regenerated from callus derived from immature inflorescence explants obtained from field grown plants. MS medium containing 4.52 μM 2, 4-D and 3.33 μM BAP was found to be most effective for the proliferation of callus, induced on medium containing 4.52 μM 2, 4-D. Maximum number (43.1 ± 0.25) with average length (5.2 ± 0.23) of shoots regenerated when callus was transferred to MS medium supplemented with 1.11 μM BAP, 1.16 μM Kin and 0.57 μM IAA. About 75.5 % of in vitro regenerated shoots were rooted on half-strength MS medium supplemented with 9.84 μM of IBA and 200 mg l⁻¹ of activated charcoal. In comparison to in vitro, higher percent (90.2 %) of shoots were rooted under ex vitro conditions when treated with IBA (0.98 mM) for 5 min. Plantlets rooted in vitro as well as ex vitro were acclimatized successfully under the green house conditions. Ex vitro rooted plants exhibited higher survival percentage (75 %) as compared to in vitro rooted plantlets (60 %). Present study may be applicable in the large-scale root-specific red dye (alkannin) production via root induction under ex vitro condition.     

Mixed Polyethylene Glycol-Modified Breviscapine-Loaded Solid Lipid Nanoparticles for Improved Brain Bioavailability: Preparation,Characterization, and In Vivo Cerebral Microdialysis Evaluation in Adult Sprague Dawley Rats

Breviscapine is used in the treatment of ischemic cerebrovascular diseases, but it has a low bioavailability in the brain due to its poor physicochemical properties and the activity of P-glycoprotein efflux pumps located at the blood–brain barrier. In the present study, breviscapine-loaded solid lipid nanoparticles (SLN) coated with polyethylene glycol (PEG) derivatives were formulated and evaluated for their ability to enhance brain bioavailability. The SLNs were either coated with polyethylene glycol (40) (PEG-40) stearate alone (Bre-GBSLN-PS) or a mixture of PEG-40 stearate and 1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-PEG2000 (DSPE-PEG₂₀₀₀) (Bre-GBSLN-PS-DSPE) and were characterized both in vitro and in vivo. The mean particle size, polydispersity index, and entrapment efficiency for Bre-GBSLN-PS and Bre-GBSLN-PS-DSPE were 21.60 ± 0.10 and 22.60 ± 0.70 nm, 0.27 ± 0.01 and 0.26 ± 0.04, and 46.89 ± 0.73% and 47.62 ± 1.86%, respectively. The brain pharmacokinetic parameters revealed that the brain bioavailability of breviscapine from the Bre-GBSLN-PS and Bre-GBSLN-PS-DSPE was significantly enhanced (p < 0.01) with the area under concentration–time curve (AUC) of 1.59 ± 0.39 and 1.42 ± 0.58 μg h/mL of breviscapine, respectively, in comparison to 0.11 ± 0.02 μg h/mL from the commercial breviscapine injection. The ratios of the brain AUC for scutellarin in comparison with the plasma scutellarin AUC for commercial breviscapine injection, Bre-GBSLN-PS, and Bre-GBSLN-PS-DSPE were 0.66%, 2.82%, and 4.51%, respectively. These results showed that though both SLN formulations increased brain uptake of breviscapine, Bre-GBSLN-PS-DSPE which was coated with a binary combination of PEG-40 stearate and DSPE-PEG₂₀₀₀ had a better brain bioavailability than Bre-GBSLN-PS. Thus, the coating of SLNs with the appropriate PEG derivative combination could improve brain bioavailability of breviscapine and can be a promising tool for brain drug delivery.KEY WORDS: breviscapine, microdialysis, mixed PEGylation, P-glycoprotein (P-gp), solid lipid nanoparticles     

Development and Characterization of Lyophilized Diazepam-Loaded Polymeric Micelles

Polymeric micelles were studied as delivery carriers of diazepam, a practically insoluble drug in water, for rectal administration. The diazepam-loaded polymeric micelles were developed by using poloxamer 407 (P407), poloxamer 188, and d-α-tocopheryl poly(ethylene glycol) 1000 succinate (TPGS). Among the used polymers, TPGS resulted in polymeric micelles with good characteristics for encapsulation of diazepam which had the small particle size of 8–12 nm and narrow size distribution (PI 0.053–0.275). Additionally, 7.5% w/v of TPGS could entirely entrap the desired concentration of diazepam (5 mg/mL). To improve the physical stability upon lyophilization, an addition of P407 of 1% w/v prevented aggregation, increased physical stability, and maintained chemical stability of the lyophilized powders of diazepam-loaded polymeric micelles for 3 months storage at 4°C. The rate and amount of diazepam release from TPGS polymeric micelles mainly depended on the concentration of TPGS. The release data were fitted to Higuchi''s model suggesting that the drug release mechanism was controlled by Fickian diffusion. In conclusion, 10% w/v TPGS and 1% w/v P407 were the optimum formulation of lyophilized diazepam-loaded polymeric micelles.Key words: diazepam, lyophilization, poloxamer 407, polymeric micelles, d-α-tocopheryl poly(ethylene glycol) 1000 succinate (TPGS)     

Design and In Vitro Evaluation of Finasteride-Loaded Liquid Crystalline Nanoparticles for Topical Delivery

In this study, liquid crystalline nanoparticles (LCN) have been proposed as new carrier for topical delivery of finasteride (FNS) in the treatment of androgenetic alopecia. To evaluate the potential of this nanocarrier, FNS-loaded LCN was prepared by ultrasonication method and characterized for size, shape, in vitro release, and skin permeation–retention properties. The particle size ranged from 153.8 to 170.2 nm with a cubical shape and exhibited controlled release profile with less than 20% of the drug released in the first 24 h. The release profile was significantly altered with addition of different additives. Formulation with lower monoolein exhibited higher skin permeation with a flux rate of 0.061 ± 0.005 μg cm⁻² h⁻¹ in 24 h. The permeation however, significantly increased with glycerol, propylene glycol, and polyethylene glycol 400, while it declined for the addition of oleic acid. A similar trend was observed with skin retention study. In conclusion, FNS-loaded LCN could be advocated as a viable alternative for oral administration of the drug.Key words: androgenetic alopecia, finasteride, liquid crystalline nanoparticles, release, skin permeation–retention     

Development of Controlled-Release Matrix Tablet of Risperidone: Influence of Methocel®- and Ethocel®-Based Novel Polymeric Blend on <Emphasis Type="Italic">In Vitro</Emphasis> Drug Release and Bioavailability

Controlled-release (CR) matrix tablet of 4 mg risperidone was developed using flow bound dry granulation–slugging method to improve its safety profile and compliance. Model formulations F1, F2, and F3, consisting of distinct blends of Methocel® K100 LV-CR and Ethocel® standard 7FP premium, were slugged. Each batch of granules (250–1,000 μm), obtained by crushing the slugs, was divided into three portions after lubrication and then compressed to 9-, 12-, and 15-kg hard tablets. In vitro drug release studies were carried out in 0.1 N HCl (pH 1.2) and phosphate buffer (pH 6.8) using a paddle dissolution apparatus run at 50 rpm. The CR test tablet, containing 30% Methocel® and 60% Ethocel® (F3) with 12-kg hardness, exhibited pH-independent zero-order release kinetics for 24 h. The drug release rate was inversely proportional to the content of Ethocel®, while the gel layer formed of Methocel® helped in maintaining the integrity of the matrix. Changes in the hardness of tablet did not affect the release kinetics. The tablets were reproducible and stable for 6 months at 40 ± 2°C/75 ± 5% relative humidity. Risperidone and its active metabolite, 9-hydroxyrisperidone, present in the pooled rabbit’s serum, were analyzed with HPLC-UV at λ_max 280 nm. The CR test tablet exhibited bioequivalence to reference conventional tablet in addition to the significantly (p < 0.05) optimized peak concentration, C_max, and extended peak time, T_max, of the active moiety. There was a good association between drug absorption in vivo and drug release in vitro (R² = 0.7293). The successfully developed CR test tablet may be used for better therapeutic outcomes of risperidone.KEY WORDS: controlled release, dry granulation slugging method, risperidone     

Formulation and In Vitro Evaluation of Salbutamol Sulphate In Situ Gelling Nasal Inserts

The aim of this study was to formulate salbutamol sulfate (SS), a model drug, as mucoadhesive in situ gelling inserts having a high potential as nasal drug delivery system bypassing the first-pass metabolism. In situ gelling inserts, each containing 1.4% SS and 2% gel-forming polymer, hydroxypropyl methylcellulose (HPMC), carboxymethylcellulose sodium (CMC Na), sodium alginate (AL), and chitosan (CH) were prepared. The inserts were investigated for their different physicochemical properties. The weight of inserts was 16–27 mg, drug content was 3.9–4.2 mg, thickness ranged between 15 and 28 μm and surface pH was 5–7. Cumulative drug released from the inserts exhibited extended release for more than 10 h following the decreasing order: CH > AL > CMC Na > HPMC. The drug release from CMC Na and AL inserts followed zero-order kinetics while HPMC and CH inserts exhibited non-Fickian diffusion mechanism. The inserts exhibited different water uptake (7–23%) with the smallest values for CH. Differential scanning calorimetry study pointed out possible interaction of SS and oppositely charged anionic polymers (CMC Na and AL). The mucoadhesive in situ gelling inserts exhibited satisfactory mucoadhesive and extended drug release characteristics. The inserts could be used for nasal delivery of SS over about 12 h; bypassing the hepatic first-pass metabolism without potential irritation.KEY WORDS: in situ gelling inserts, mucoadhesion, nasal delivery, salbutamol sulfate     

Simultaneous quantification of 12 different nucleotides and nucleosides released from renal epithelium and in human urine samples using ion-pair reversed-phase HPLC

Nucleotides and nucleosides are not only involved in cellular metabolism but also act extracellularly via P1 and P2 receptors, to elicit a wide variety of physiological and pathophysiological responses through paracrine and autocrine signalling pathways. For the first time, we have used an ion-pair reversed-phase high-performance liquid chromatography ultraviolet (UV)-coupled method to rapidly and simultaneously quantify 12 different nucleotides and nucleosides (adenosine triphosphate, adenosine diphosphate, adenosine monophosphate, adenosine, uridine triphosphate, uridine diphosphate, uridine monophosphate, uridine, guanosine triphosphate, guanosine diphosphate, guanosine monophosphate, guanosine): (1) released from a mouse renal cell line (M1 cortical collecting duct) and (2) in human biological samples (i.e., urine). To facilitate analysis of urine samples, a solid-phase extraction step was incorporated (overall recovery rate ≥ 98 %). All samples were analyzed following injection (100 μl) into a Synergi Polar-RP 80 Å (250 × 4.6 mm) reversed-phase column with a particle size of 10 μm, protected with a guard column. A gradient elution profile was run with a mobile phase (phosphate buffer plus ion-pairing agent tetrabutylammonium hydrogen sulfate; pH 6) in 2–30 % acetonitrile (v/v) for 35 min (including equilibration time) at 1 ml min⁻¹ flow rate. Eluted compounds were detected by UV absorbance at 254 nm and quantified using standard curves for nucleotide and nucleoside mixtures of known concentration. Following validation (specificity, linearity, limits of detection and quantitation, system precision, accuracy, and intermediate precision parameters), this protocol was successfully and reproducibly used to quantify picomolar to nanomolar concentrations of nucleosides and nucleotides in isotonic and hypotonic cell buffers that transiently bathed M1 cells, and urine samples from normal subjects and overactive bladder patients.

Electronic supplementary material

The online version of this article (doi:10.1007/s11302-012-9321-8) contains supplementary material, which is available to authorized users.     

Photodegradation and Stabilization of Betamethasone-17 Valerate in Aqueous/Organic Solvents and Topical Formulations

The effects of solvent [acetonitrile, methanol, and acetonitrile/water mixture (20:80, v/v)], buffer concentration (phosphate buffer, pH 7.5), ionic strength and commonly employed adjuvants on the photodegradation of betamethasone-17 valerate in cream and gel formulations have been studied on exposure to UV light (300–400 nm). A validated high-performance liquid chromatography method has been used to determine the parent compound and its photodegraded products. The photodegradation data in the studied solvents showed greater decomposition of the drug in solvents with a lower dielectric constant. A comparatively higher rate of photodegradation was observed in the cream formulation compared to that for the gel formulation. The kinetic treatment of the photodegradation data revealed that the degradation of the drug follows first-order kinetics and the apparent first-order rate constants for the photodegradation reactions, in the media studied, range from 1.62 to 11.30 × 10⁻³ min⁻¹. The values of the rate constants decrease with increasing phosphate concentration and ionic strength which could be due to the deactivation of the excited state and radical quenching. The second-order rate constant (k′) for the phosphate ion-inhibited reactions at pH 7.5 has been found to be 5.22 × 10⁻² M⁻¹ s⁻¹. An effective photostabilization of the drug has been achieved in cream and gel formulations with titanium dioxide (33.5–42.5%), vanillin (21.6–28.7%), and butyl hydroxytoluene (18.2–21.6%).Key words: betamethasone-17 valerate, creams and gels, kinetics, photodegradation, photostabilization     

Simultaneous Determination of EDTA, Sorbic Acid, and Diclofenac Sodium in Pharmaceutical Preparations Using High-Performance Liquid Chromatography

A simple high-performance liquid chromatographic method for simultaneous determination of ethylenediaminetetraacetic acid (EDTA), sorbic acid, and diclofenac sodium was developed and validated. Separation was achieved on a C₁₈ column (10 cm × 4.6 mm) using gradient elution. The mobile phase consisted of acetonitrile–ammonium dihydrogen phosphate buffer solution (0.01 M, pH = 2.5, containing 0.8% tetra-n-butyl ammonium hydroxide). The detector wavelength was set at 254 nm. Under these conditions, separation of three compounds was achieved in less than 10 min. The effect of two metal salts and metal concentration on peak area of EDTA was investigated. The pH effect on retention of EDTA and sorbic acid was studied. The method showed linearity for EDTA, sorbic acid, and diclofenac in the ranges of 2.5–100.0, 5.0–200.0, and 20.0–120.0 μg/mL, respectively. The within- and between-day relative standard deviations ranged from 0.52 to 1.94%, 0.50 to 1.34%, and 0.78 to 1.67% for EDTA, sorbic acid, and diclofenac, respectively. The recovery of EDTA, sorbic acid, and diclofenac from pharmaceutical preparation ranged from 96.0–102.0%, 99.7–101.5%, to 97.0–102.5%, respectively. To the best of our knowledge, this is the first report about simultaneous determination of EDTA, sorbic acid, and diclofenac.KEY WORDS: diclofenac sodium, EDTA, high-performance liquid chromatography, pharmaceutical preparations, sorbic acid     

In vitro propagation and withaferin A production in Withania ashwagandha,a rare medicinal plant of India

Withania ashwagandha, belonging to the family Solanaceae, is an important medicinal herb of India with restricted geographic distribution. It is a rich source of withaferin A (WA) and other bioactive withanolides. In the present study a rapid in vitro mass propagation protocol of W. ashwagandha was developed from nodal explants. Nodal explants were cultured on MS medium supplemented with various concentrations and combinations of plant growth regulators (PGRs). The highest number of regenerated shoots per ex-plant (33 ± 2.7) and highest WA (13.4 ± 1.15 mg/g of DW) production was obtained on MS medium supplemented with 5.0 μM 6-benzyladenine (BA) and 1.0 μM Kinetin (Kn). In vitro raised shoots were further rooted on half-strength MS medium containing 2.0 μM Indole-3-butyric acid (IBA) and analyzed for WA production. The rooted plantlets when transferred to poly bags in the greenhouse showed 90 % survival frequency. Levels of WA were higher in the in vitro and ex vitro derived shoot and root tissues as compared to field grown mother plants. In an attempt to further maximize WA production, shoot cultures were further grown in liquid MS medium supplemented with 5.0 μM 6-benzyladenine (BA) and 1.0 μM Kinetin (Kn). Root cultures were grown on half strength MS liquid medium fortified with 2.0 μM of IBA. WA production in the liquid cultures was significantly higher compared to the static composition of the same media. This protocol, first of its kind in this plant, can be successfully employed for conservation, proliferation and large-scale production of WA. The regenerated plants can also be used in traditional medicine as an alternative to naturally collected plants.     

Adaptation of cancer cells from different entities to the MDM2 inhibitor nutlin-3 results in the emergence of p53-mutated multi-drug-resistant cancer cells

Six p53 wild-type cancer cell lines from infrequently p53-mutated entities (neuroblastoma, rhabdomyosarcoma, and melanoma) were continuously exposed to increasing concentrations of the murine double minute 2 inhibitor nutlin-3, resulting in the emergence of nutlin-3-resistant, p53-mutated sublines displaying a multi-drug resistance phenotype. Only 2 out of 28 sublines adapted to various cytotoxic drugs harboured p53 mutations. Nutlin-3-adapted UKF-NB-3 cells (UKF-NB-3^rNutlin^10 μM, harbouring a G245C mutation) were also radiation resistant. Analysis of UKF-NB-3 and UKF-NB-3^rNutlin^10 μM cells by RNA interference experiments and lentiviral transduction of wild-type p53 into p53-mutated UKF-NB-3^rNutlin^10 μM cells revealed that the loss of p53 function contributes to the multi-drug resistance of UKF-NB-3^rNutlin^10 μM cells. Bioinformatics PANTHER pathway analysis based on microarray measurements of mRNA abundance indicated a substantial overlap in the signalling pathways differentially regulated between UKF-NB-3^rNutlin^10 μM and UKF-NB-3 and between UKF-NB-3 and its cisplatin-, doxorubicin-, or vincristine-resistant sublines. Repeated nutlin-3 adaptation of neuroblastoma cells resulted in sublines harbouring various p53 mutations with high frequency. A p53 wild-type single cell-derived UKF-NB-3 clone was adapted to nutlin-3 in independent experiments. Eight out of ten resulting sublines were p53-mutated harbouring six different p53 mutations. This indicates that nutlin-3 induces de novo p53 mutations not initially present in the original cell population. Therefore, nutlin-3-treated cancer patients should be carefully monitored for the emergence of p53-mutated, multi-drug-resistant cells.