High cell density perfusion cultures of anchorage-dependent Vero cells in a depth filter perfusion system

A depth filter perfusion system (DFPS) with polypropylene fibers had been demonstrated to support high density cultures of anchorage-independent hybridoma cells. The DFPS provides advantages of high surface-to-volume ratio of 450–600 cm²/cm³, low cost set-up, easy operation and scale-up. To test the feasibility of using DFPS for high density cultures of anchorage-dependent cells, Vero cells were cultivated in the DFPS. Gelatin coating on polypropylene fibers in the DFPS was necessary to promote cell attachment and growth. Dissolved oxygen (DO) concentrations could be controlled by sparging air into the reservoir vessel through a filter sparger. When DO concentration was controlled above 40% of air saturation in the DFPS with 40 m pore size, the maximum cell concentration as estimated on specific lactate production rate, was 3.81×10⁷ cells/ml of the total reactor volume. This viable cell concentration is approximately 18 times higher than that obtained in a T-flask batch culture. Taken together, the results obtained here showed the potential of DFPS for high-density cultures of anchorage-dependent cells.     

Very high density of CHO cells in perfusion by ATF or TFF in WAVE bioreactor™. Part I. Effect of the cell density on the process

High cell density perfusion process of antibody producing CHO cells was developed in disposable WAVE Bioreactor? using external hollow fiber filter as cell separation device. Both “classical” tangential flow filtration (TFF) and alternating tangential flow system (ATF) equipment were used and compared. Consistency of both TFF‐ and ATF‐based cultures was shown at 20–35 × 10⁶ cells/mL density stabilized by cell bleeds. To minimize the nutrients deprivation and by‐product accumulation, a perfusion rate correlated to the cell density was applied. The cells were maintained by cell bleeds at density 0.9–1.3 × 10⁸ cells/mL in growing state and at high viability for more than 2 weeks. Finally, with the present settings, maximal cell densities of 2.14 × 10⁸ cells/mL, achieved for the first time in a wave‐induced bioreactor, and 1.32 × 10⁸ cells/mL were reached using TFF and ATF systems, respectively. Using TFF, the cell density was limited by the membrane capacity for the encountered high viscosity and by the pCO₂ level. Using ATF, the cell density was limited by the vacuum capacity failing to pull the highly viscous fluid. Thus, the TFF system allowed reaching higher cell densities. The TFF inlet pressure was highly correlated to the viscosity leading to the development of a model of this pressure, which is a useful tool for hollow fiber design of TFF and ATF. At very high cell density, the viscosity introduced physical limitations. This led us to recommend cell densities under 1.46 × 10⁸ cell/mL based on the analysis of the theoretical distance between the cells for the present cell line. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 29:754–767, 2013     

Recovery of insect cells using hollow fiber microfiltration

An efficient method was developed for media separation and cell collection for eukaryotic cells growing in suspension. The method is based on tangential flow microfiltration using an open channel arrangement in a hollow fiber configuration. Best results (highest processing flux rate) for polysulfone hollow fibers were obtained using fibers with internal diameter of 0.75 mm, 0.45 mum pore size, and a cell suspension flow at a shear rate of 14000 s(-1) (0.032 L/min per fiber). A flux rate of 500 L/m(2) h can be obtained by maintaining the surface area/cell ratio at 0.05 m(2)/10 L of cells at a concentration of 2.5 x 10(6) cells/mL. Forty liters of infected insect cells can be concentrated 10 times in 20 min without affecting cell viability. (c) 1995 John Wiley & Sons, Inc.     

High density culture of hybridoma cells using a perfusion culture vessel with an external centrifuge

The influence of centrifugal force on the growth of cells was examined by exposing the cells of the mouse-human hybridoma X87 line to centrifugal force (100–500 G) for ten minutes twice a day and comparing the static culture with that of unexposed cells. In this experiment, both cell proliferation and specific antibody productivity were independent of the centrifugal effect, and gave the same results as in the case of no exposure to centrifugal force. High density cultivation of the mouse-human hybridoma X87 line was obtained by a perfusion system where the cells were separated from the culture medium by continuous centrifugation. In the serum-free culture, the maximum viable cell density exceeded 10⁷ cells/ml, and monoclonal antibody was stably produced for 37 days. The results in this culture were equivalent to those obtained by intermittent centrifugal cell separation from the culture medium, and separation by gravitational settlement.     

Design and validation of a pulsatile perfusion bioreactor for 3D high cell density cultures

This study presents the design and validation of a pulsatile flow perfusion bioreactor able to provide a suitable environment for 3D high cell density cultures for tissue engineering applications. Our bioreactor system is mobile, does not require the use of traditional cell culture incubators and is easy to sterilize. It provides real‐time monitoring and stable control of pH, dissolved oxygen concentration, temperature, pressure, pulsation frequency, and flow rate. In this bioreactor system, cells are cultured in a gel within a chamber perfused by a culture medium fed by hollow fibers. Human umbilical vein endothelial cells (HUVEC) suspended in fibrin were found to be living, making connections and proliferating up to five to six times their initial seeding number after a 48‐h culture period. Cells were uniformly dispersed within the 14.40 mm × 17.46 mm × 6.35 mm chamber. Cells suspended in 6.35‐mm thick gels and cultured in a traditional CO₂ incubator were found to be round and dead. In control experiments carried out in a traditional cell culture incubator, the scarcely found living cells were mostly on top of the gels, while cells cultured under perfusion bioreactor conditions were found to be alive and uniformly distributed across the gel. Biotechnol. Bioeng. 2009; 104: 1215–1223. © 2009 Wiley Periodicals, Inc.     

哺乳动物细胞灌流培养工艺开发与优化

近年来生物药市场需求量激增,高产量、高质量、低成本的哺乳动物细胞灌流培养工艺顺势成为工业界和学术界普遍关注的热点。文中围绕灌流培养工艺特有的操作环节及工艺优化应着重关注的细节展开论述,综述了近年来在灌流培养工艺开发和优化上取得的进步和提出的策略,以期为哺乳动物细胞灌流培养技术的开发提供参考。     

High density culture of mouse-human hybridoma cells using a perfusion culture apparatus with multi-settling zones to separate cells from the culture medium

Mouse-human hybridoma X87X cells were cultivated using a novel perfusion culture apparatus provided with three-settling zones to separate the cells from the culture medium by gravitational settling. The maximum viable cell density in a serum-free culture medium attained 3.0×10⁷ cells/ml, when the specific perfusion rate was set to 2.3 vol day^-1, and monoclonal antibody was continuously produced. These results were almost the same as those in the perfusion culture vessel with one settling zone and revealed that the process with a plurality of settling zones is a promising one for scale-up of a gravitation type of perfusion culture vessel.     

High cell density perfusion culture of hybridoma cells recycling high molecular weight components

We have developed a high cell density and high product concentration culture system recycling high molecular weight components. The production of monoclonal antibodies in high concentration was performed by this culture system with mouse human hybridoma H2 and V6 cells in serum-free defined media.The concentration of IgG after 48 days culture of H2 cells in ITES-eRDF reached 2 mg/ml and the purity of IgG in culture fluid was 61%. In addition, high molecular weight components in serum-free media, such as transferrin or BSA, could be reduced to 5% of the original concentration.     

High density continuous production of murine pluripotent cells in an acoustic perfused bioreactor at different oxygen concentrations

Strategies for the production of pluripotent stem cells (PSCs) rely on serially dissociated adherent or aggregate‐based culture, consequently limiting robust scale‐up of cell production, on‐line control and optimization of culture conditions. We recently developed a method that enables continuous (non‐serially dissociated) suspension culture‐mediated reprogramming to pluripotency. Herein, we use this method to demonstrate the scalable production of PSCs and early derivatives using acoustic filter technology to enable continuous oxygen‐controlled perfusion culture. Cell densities of greater than 1 × 10⁷ cells/mL were achieved after 7 days of expansion at a specific growth rate (µ) of 0.61 ± 0.1 day^?1 with a perfusion rate (D) of 5.0 day^?1. A twofold increase in maximum cell density (to greater than 2.5 × 10⁷ cells/mL) was achieved when the medium dissolved oxygen was reduced (5% DO). Cell densities and viabilities >80% were maintained for extended production periods during which maintenance of pluripotency was confirmed by stable expression of pluripotency factors (SSEA‐1 and Nanog), as well as the capacity to differentiate into all three germ layers. This work establishes a versatile biotechnological platform for the production of pluripotent cells and derivatives in an integrated, scalable and intensified stirred suspension culture. Biotechnol. Bioeng. 2013; 110: 648–655. © 2012 Wiley Periodicals, Inc.     

Virus harvesting in perfusion culture: Choosing the right type of hollow fiber membrane

The use of bioreactors coupled to membrane-based perfusion systems enables very high cell and product concentrations in vaccine and viral vector manufacturing. Many virus particles, however, are not stable and either lose their infectivity or physically degrade resulting in significant product losses if not harvested continuously. Even hollow fiber membranes with a nominal pore size of 0.2 µm can retain much smaller virions within a bioreactor. Here, we report on a systematic study to characterize structural and physicochemical membrane properties with respect to filter fouling and harvesting of yellow fever virus (YFV; ~50 nm). In tangential flow filtration perfusion experiments, we observed that YFV retention was only marginally determined by nominal but by effective pore sizes depending on filter fouling. Evaluation of scanning electron microscope images indicated that filter fouling can be reduced significantly by choosing membranes with (i) a flat inner surface (low boundary layer thickness), (ii) a smooth material structure (reduced deposition), (iii) a high porosity (high transmembrane flux), (iv) a distinct pore size distribution (well-defined pore selectivity), and (v) an increased fiber wall thickness (larger effective surface area). Lowest filter fouling was observed with polysulfone (PS) membranes. While the use of a small-pore PS membrane (0.08 µm) allowed to fully retain YFV within the bioreactor, continuous product harvesting was achieved with the large-pore PS membrane (0.34 µm). Due to the low protein rejection of the latter, this membrane type could also be of interest for other applications, that is, recombinant protein production in perfusion cultures.     

High density culture of mammalian cells with dynamic perfusion based on on-line oxygen uptake rate measurements

In a continuous culture with cell retention the perfusion rate must be adjusted dynamically to meet the cellular demand. An automated mechanism of adjusting the perfusion rate based on real-time measurement of the metabolic load of the bioreactor is important in achieving a high cell concentration and maintaining high viability. We employed oxygen uptake rate (OUR) measurement as an on-line metabolic indicator of the physiological state of the cells in the bioreactor and adjusted the perfusion rate accordingly. Using an internal hollow fiber microfiltration system for total cell retention, a cell concentration of almost 10⁸ cells/mL was achieved. Although some aggregates were formed during the cultivation, the viability remained high as examined with confocal microscopy after fluorescent vital staining. The results demonstrate that on-line OUR measurement facilitates automated dynamic perfusion and allows a high cell concentration to be achieved.     

Three hours of perfusion culture prior to 28 days of static culture, enhances osteogenesis by human cells in a collagen GAG scaffold

In tissue engineering, bioreactors can be used to aid in the in vitro development of new tissue by providing biochemical and physical regulatory signals to cells and encouraging them to undergo differentiation and/or to produce extracellular matrix prior to in vivo implantation. This study examined the effect of short term flow perfusion bioreactor culture, prior to long‐term static culture, on human osteoblast cell distribution and osteogenesis within a collagen glycosaminoglycan (CG) scaffold for bone tissue engineering. Human fetal osteoblasts (hFOB 1.19) were seeded onto CG scaffolds and pre‐cultured for 6 days. Constructs were then placed into the bioreactor and exposed to 3 × 1 h bouts of steady flow (1 mL/min) separated by 7 h of no flow over a 24‐h period. The constructs were then cultured under static osteogenic conditions for up to 28 days. Results show that the bioreactor and static culture control groups displayed similar cell numbers and metabolic activity. Histologically, however, peripheral cell‐encapsulation was observed in the static controls, whereas, improved migration and homogenous cell distribution was seen in the bioreactor groups. Gene expression analysis showed that all osteogenic markers investigated displayed greater levels of expression in the bioreactor groups compared to static controls. While static groups showed increased mineral deposition; mechanical testing revealed that there was no difference in the compressive modulus between bioreactor and static groups. In conclusion, a flow perfusion bioreactor improved construct homogeneity by preventing peripheral encapsulation whilst also providing an enhanced osteogenic phenotype over static controls. Bioeng. 2011; 108:1203–1210. © 2010 Wiley Periodicals, Inc.     

A high-rate perfusion bioreactor for plant cells

A perfusion bioreactor allowing continuous extraction of secondary metabolites was designed and challenged for Eschscholtzia californica plant cell suspensions. Four sedimentation columns mounted inside a 2.5-L bioreactor separated single cells and cell aggregates from the culture medium. Cells were elicited with chitin at day 4 and the liquid medium free of cells and debris was then continuously pumped to the extraction columns containing fluidized XAD-7 resins, and then recirculated back to the cell suspension. A medium upward velocity corresponding to cell sedimentation velocity maintained a stable cell/medium separation front in the columns for sedimented cell volume (SCV) of 90% (70% packed cell volume, PCV). Two perfusion bioreactor cultures of 10 and 14 days were performed. A maximum dilution rate of 20.4/day was reached from day 4 to day 6, and was then reduced to 5/day at day 9 for 55% SCV. Control cultures were performed without and with free extraction resins into the cell suspension. Perfusion cultures showed similar specific growth rates of 0.24 +/- 0.04/day before and after elicitation. However, production level in the perfusion cultures was similar to that from the culture without resins with a maximum of 2.06 micromole/gDW total alkaloids, with 1.54 micromole/gDW in the resins. Cultures with free resins resulted in 30.94 micromole/gDW with 28.4 +/- 8.8 micromole/gDW in the resins. Difference in the cells nutritional state from elicitation was identified as a major cause in the production reduction. However, pathway to chelilutine was favored in the continuous extraction culture.     

High density microcarrier culture with a new device which allows oxygenation and perfusion of microcarrier cultures

A novel system useful for aeration and cell retention in continuous perfused microcarrier cultures is described. The system is based on a vibrating cage that separates cells and microcarriers from the oxygenation chamber and allows gas bubble free oxygen transfer. In the cultivation of monkey kidney cells (VERO) on gelatin coated microcarriers, using different concentrations (5, 10 and 15 g Cytodex 3/liter) cell densities up to 10⁷ cells per ml were obtained. The described system is scaleable.     

Occurrence of the Crabtree effect in HeLa cells

The occurrence of a Crabtree effect in HeLa cells was detected. Some properties of pyruvate kinase (PK) were also evaluated. Hexose phosphate, triose-phosphate and phosphoenolpyruvate (PEP) significantly decreased the oxygen consumption of digitonin-permeabilized HeLa cells, which were oxidizing succinate. The Crabtree effect promoted by PEP was concentration-dependent and was lowered by an increase of ADP concentration, suggesting a participation of PK. The dependence of fructose-1,6-bisphosphate (FDP) by HeLa cell PK was observed. The PK of HeLa cells was inhibited by L -alanine only in the absence of FDP, while in the presence of the metabolite, an increase in the activity was observed. PK was also inhibited in the presence of L -histidine and L -leucine, while L -serine promoted activation. L -Cysteine and L -phenylalanine also inhibited the PK of HeLa cells. This, together with the sigmoidal character in relation to substrate concentration, suggests the presence of the K-type of PK in HeLa cells. © 1998 John Wiley & Sons, Ltd.     

Modulation of transmembrane pressure in manufacturing scale tangential flow filtration N-1 perfusion seed culture

Mammalian cells were grown to high density in a 3,000 L culture using perfusion with hollow fibers operated in a tangential flow filtration mode. The high-density culture was used to inoculate the production stage of a biomanufacturing process. At constant permeate flux operation, increased transmembrane pressures (TMPs) were observed on the final day of the manufacturing batches. Small scale studies suggested that the filters were not irreversibly fouled, but rather exposed to membrane concentration polarization that could be relieved by tangential sweeping of the hollow fibers. Studies were undertaken to analyze parameters that influence the hydrodynamic profile within hollow fibers; including filter area, cell density, recirculation flow rate, and permeate flow rate. Results indicated that permeate flow rate had the greatest influence on modulating TMP. Further evaluation showed a significant decrease in TMP when permeate flow was reduced, and this occurred without any negative effect on cell growth or viability. Hence, a 30% reduction of permeate flow rate was implemented at manufacturing scale. A stable operation was achieved as TMP was successfully reduced by 75% while preserving all critical factors for performance in the perfusion bioreactor.     

Effect of culture temperature on erythropoietin production and glycosylation in a perfusion culture of recombinant CHO cells

To investigate the effect of culture temperature on erythropoietin (EPO) production and glycosylation in recombinant Chinese hamster ovary (CHO) cells, we cultivated CHO cells using a perfusion bioreactor. Cells were cultivated at 37 degrees C until viable cell concentration reached 1 x 10(7) cells/mL, and then culture temperature was shifted to 25 degrees C, 28 degrees C, 30 degrees C, 32 degrees C, 37 degrees C (control), respectively. Lowering culture temperature suppressed cell growth but was beneficial to maintain high cell viability for a longer period. In a control culture at 37 degrees C, cell viability gradually decreased and fell below 80% on day 18 while it remained over 90% throughout the culture at low culture temperature. The cumulative EPO production and specific EPO productivity, q(EPO), increased at low culture temperature and were the highest at 32 degrees C and 30 degrees C, respectively. Interestingly, the cumulative EPO production at culture temperature below 32 degrees C was not as high as the cumulative EPO production at 32 degrees C although the q(EPO) at culture temperature below 32 degrees C was comparable or even higher than the q(EPO) at 32 degrees C. This implies that the beneficial effect of lowering culture temperature below 32 degrees C on q(EPO) is outweighed by its detrimental effect on the integral of viable cells. The glycosylation of EPO was evaluated by isoelectric focusing, normal phase HPLC and anion exchange chromatography analyses. The quality of EPO at 32 degrees C in regard to acidic isoforms, antennary structures and sialylated N-linked glycans was comparable to that at 37 degrees C. However, at culture temperatures below 32 degrees C, the proportions of acidic isoforms, tetra-antennary structures and tetra-sialylated N-linked glycans were further reduced, suggesting that lowering culture temperature below 32 degrees C negatively affect the quality of EPO. Thus, taken together, cell culture at 32 degrees C turned out to be the most satisfactory since it showed the highest cumulative EPO production, and moreover, EPO quality at 32 degrees C was not deteriorated as obtained at 37 degrees C.     

Effect of interferon on the infectivity of Trypanosoma cruzi in cultured HeLa cells

Results are presented on the effects of human lymphoblastoid interferon (HUIFN-α-ly) on the infectivity of metacyclic culture forms of Trypanosoma cruzi in HeLa cells. When cells were pretreated with interferon the parasitisation ratios of the cultures increased with respect to controls. This phenomenon also occurs when interferon was added during the period of parasite-cell interaction. When parasites were pretreated with interferon but cells were not, no increase in the parasitisation ratios was observed.